Commit 567c8903 authored by Johan Rudholm's avatar Johan Rudholm Committed by Chris Ball

mmc: core: Break out start_signal_voltage_switch

Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.

Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: default avatarJohan Rudholm <johan.rudholm@stericsson.com>
Acked-by: default avatarUlf Hansson <ulf.hansson@linaro.org>
Tested-by: default avatarWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: default avatarChris Ball <cjb@laptop.org>
parent d887874e
......@@ -1317,7 +1317,26 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
return ocr;
}
int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11)
int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
{
int err = 0;
int old_signal_voltage = host->ios.signal_voltage;
host->ios.signal_voltage = signal_voltage;
if (host->ops->start_signal_voltage_switch) {
mmc_host_clk_hold(host);
err = host->ops->start_signal_voltage_switch(host, &host->ios);
mmc_host_clk_release(host);
}
if (err)
host->ios.signal_voltage = old_signal_voltage;
return err;
}
int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
{
struct mmc_command cmd = {0};
int err = 0;
......@@ -1328,7 +1347,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11
* Send CMD11 only if the request is to switch the card to
* 1.8V signalling.
*/
if ((signal_voltage != MMC_SIGNAL_VOLTAGE_330) && cmd11) {
if (signal_voltage != MMC_SIGNAL_VOLTAGE_330) {
cmd.opcode = SD_SWITCH_VOLTAGE;
cmd.arg = 0;
cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
......@@ -1341,15 +1360,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11
return -EIO;
}
host->ios.signal_voltage = signal_voltage;
if (host->ops->start_signal_voltage_switch) {
mmc_host_clk_hold(host);
err = host->ops->start_signal_voltage_switch(host, &host->ios);
mmc_host_clk_release(host);
}
return err;
return __mmc_set_signal_voltage(host, signal_voltage);
}
/*
......@@ -1412,7 +1423,7 @@ static void mmc_power_up(struct mmc_host *host)
mmc_set_ios(host);
/* Set signal voltage to 3.3V */
mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, false);
__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
/*
* This delay should be sufficient to allow the power supply
......
......@@ -40,8 +40,8 @@ void mmc_set_ungated(struct mmc_host *host);
void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode);
void mmc_set_bus_width(struct mmc_host *host, unsigned int width);
u32 mmc_select_voltage(struct mmc_host *host, u32 ocr);
int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage,
bool cmd11);
int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
void mmc_set_timing(struct mmc_host *host, unsigned int timing);
void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type);
void mmc_power_off(struct mmc_host *host);
......
......@@ -769,11 +769,11 @@ static int mmc_select_hs200(struct mmc_card *card)
if (card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V &&
host->caps2 & MMC_CAP2_HS200_1_2V_SDR)
err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120, 0);
err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
if (err && card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_8V &&
host->caps2 & MMC_CAP2_HS200_1_8V_SDR)
err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180, 0);
err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
/* If fails try again during next card power cycle */
if (err)
......@@ -1221,8 +1221,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
* WARNING: eMMC rules are NOT the same as SD DDR
*/
if (ddr == MMC_1_2V_DDR_MODE) {
err = mmc_set_signal_voltage(host,
MMC_SIGNAL_VOLTAGE_120, 0);
err = __mmc_set_signal_voltage(host,
MMC_SIGNAL_VOLTAGE_120);
if (err)
goto err;
}
......
......@@ -757,7 +757,7 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr)
*/
if (!mmc_host_is_spi(host) && rocr &&
((*rocr & 0x41000000) == 0x41000000)) {
err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180, true);
err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
if (err) {
ocr &= ~SD_OCR_S18R;
goto try_again;
......
......@@ -647,8 +647,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
* it.
*/
if ((ocr & R4_18V_PRESENT) && mmc_host_uhs(host)) {
err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
true);
err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
if (err) {
ocr &= ~R4_18V_PRESENT;
host->ocr &= ~R4_18V_PRESENT;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment