Commit 5d5ddb5e authored by Brian Norris's avatar Brian Norris Committed by Kalle Valo

mwifiex: pcie: don't loop/retry interrupt status checks

The following sequence occurs when using IEEE power-save on 8997:
(a) driver sees SLEEP event
(b) driver issues SLEEP CONFIRM
(c) driver recevies CMD interrupt; within the interrupt processing loop,
    we do (d) and (e):
(d) wait for FW sleep cookie (and often time out; it takes a while), FW
    is putting card into low power mode
(e) re-check PCIE_HOST_INT_STATUS register; quit loop with 0 value

But at (e), no one actually signaled an interrupt (i.e., we didn't check
adapter->int_status). And what's more, because the card is going to
sleep, this register read appears to take a very long time in some cases
-- 3 milliseconds in my case!

Now, I propose that (e) is completely unnecessary. If there were any
additional interrupts signaled after the start of this loop, then the
interrupt handler would have set adapter->int_status to non-zero and
queued more work for the main loop -- and we'd catch it on the next
iteration of the main loop.

So this patch drops all the looping/re-reading of PCIE_HOST_INT_STATUS,
which avoids the problematic (and slow) register read in step (e).

Incidentally, this is a very similar issue to the one fixed in commit
ec815dd2 ("mwifiex: prevent register accesses after host is
sleeping"), except that the register read is just very slow instead of
fatal in this case.

Tested on 8997 in both MSI and (though not technically supported at the
moment) MSI-X mode.
Signed-off-by: default avatarBrian Norris <briannorris@chromium.org>
Signed-off-by: default avatarKalle Valo <kvalo@codeaurora.org>
parent 062e008a
......@@ -2334,79 +2334,41 @@ static int mwifiex_process_pcie_int(struct mwifiex_adapter *adapter)
}
}
}
while (pcie_ireg & HOST_INTR_MASK) {
if (pcie_ireg & HOST_INTR_DNLD_DONE) {
pcie_ireg &= ~HOST_INTR_DNLD_DONE;
mwifiex_dbg(adapter, INTR,
"info: TX DNLD Done\n");
ret = mwifiex_pcie_send_data_complete(adapter);
if (ret)
return ret;
}
if (pcie_ireg & HOST_INTR_UPLD_RDY) {
pcie_ireg &= ~HOST_INTR_UPLD_RDY;
mwifiex_dbg(adapter, INTR,
"info: Rx DATA\n");
ret = mwifiex_pcie_process_recv_data(adapter);
if (ret)
return ret;
}
if (pcie_ireg & HOST_INTR_EVENT_RDY) {
pcie_ireg &= ~HOST_INTR_EVENT_RDY;
mwifiex_dbg(adapter, INTR,
"info: Rx EVENT\n");
ret = mwifiex_pcie_process_event_ready(adapter);
if (ret)
return ret;
}
if (pcie_ireg & HOST_INTR_CMD_DONE) {
pcie_ireg &= ~HOST_INTR_CMD_DONE;
if (adapter->cmd_sent) {
mwifiex_dbg(adapter, INTR,
"info: CMD sent Interrupt\n");
adapter->cmd_sent = false;
}
/* Handle command response */
ret = mwifiex_pcie_process_cmd_complete(adapter);
if (ret)
return ret;
if (adapter->hs_activated)
return ret;
}
if (card->msi_enable) {
spin_lock_irqsave(&adapter->int_lock, flags);
adapter->int_status = 0;
spin_unlock_irqrestore(&adapter->int_lock, flags);
}
if (mwifiex_pcie_ok_to_access_hw(adapter)) {
if (mwifiex_read_reg(adapter, PCIE_HOST_INT_STATUS,
&pcie_ireg)) {
mwifiex_dbg(adapter, ERROR,
"Read register failed\n");
return -1;
}
if ((pcie_ireg != 0xFFFFFFFF) && (pcie_ireg)) {
if (mwifiex_write_reg(adapter,
PCIE_HOST_INT_STATUS,
~pcie_ireg)) {
mwifiex_dbg(adapter, ERROR,
"Write register failed\n");
return -1;
}
}
}
if (!card->msi_enable) {
spin_lock_irqsave(&adapter->int_lock, flags);
pcie_ireg |= adapter->int_status;
adapter->int_status = 0;
spin_unlock_irqrestore(&adapter->int_lock, flags);
if (pcie_ireg & HOST_INTR_DNLD_DONE) {
pcie_ireg &= ~HOST_INTR_DNLD_DONE;
mwifiex_dbg(adapter, INTR, "info: TX DNLD Done\n");
ret = mwifiex_pcie_send_data_complete(adapter);
if (ret)
return ret;
}
if (pcie_ireg & HOST_INTR_UPLD_RDY) {
pcie_ireg &= ~HOST_INTR_UPLD_RDY;
mwifiex_dbg(adapter, INTR, "info: Rx DATA\n");
ret = mwifiex_pcie_process_recv_data(adapter);
if (ret)
return ret;
}
if (pcie_ireg & HOST_INTR_EVENT_RDY) {
pcie_ireg &= ~HOST_INTR_EVENT_RDY;
mwifiex_dbg(adapter, INTR, "info: Rx EVENT\n");
ret = mwifiex_pcie_process_event_ready(adapter);
if (ret)
return ret;
}
if (pcie_ireg & HOST_INTR_CMD_DONE) {
pcie_ireg &= ~HOST_INTR_CMD_DONE;
if (adapter->cmd_sent) {
mwifiex_dbg(adapter, INTR,
"info: CMD sent Interrupt\n");
adapter->cmd_sent = false;
}
/* Handle command response */
ret = mwifiex_pcie_process_cmd_complete(adapter);
if (ret)
return ret;
}
mwifiex_dbg(adapter, INTR,
"info: cmd_sent=%d data_sent=%d\n",
adapter->cmd_sent, adapter->data_sent);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment