Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
 "The usual collection of new drivers, non-critical fixes, and updates
  to existing clk drivers. The bulk of the work is on Allwinner and
  Rockchip SoCs, but there's also an Intel Atom driver in here too.

  New Drivers:
   - Tegra BPMP firmware
   - Hisilicon hi3660 SoCs
   - Rockchip rk3328 SoCs
   - Intel Atom PMC
   - STM32F746
   - IDT VersaClock 5P49V5923 and 5P49V5933
   - Marvell mv98dx3236 SoCs
   - Allwinner V3s SoCs

  Removed Drivers:
   - Samsung Exynos4415 SoCs

  Updates:
   - Migrate ABx500 to OF
   - Qualcomm IPQ4019 CPU clks and general PLL support
   - Qualcomm MSM8974 RPM
   - Rockchip non-critical fixes and clk id additions
   - Samsung Exynos4412 CPUs
   - Socionext UniPhier NAND and eMMC support
   - ZTE zx296718 i2s and other audio clks
   - Renesas CAN and MSIOF clks for R-Car M3-W
   - Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
   - TI CDCE913, CDCE937, and CDCE949 clk generators
   - Marvell Armada ap806 CPU frequencies
   - STM32F4* I2S/SAI support
   - Broadcom BCM2835 DSI support
   - Allwinner sun5i and A80 conversion to new style clk bindings"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (130 commits)
  clk: renesas: mstp: ensure register writes complete
  clk: qcom: Do not drop device node twice
  clk: mvebu: adjust clock handling for the CP110 system controller
  clk: mvebu: Expand mv98dx3236-core-clock support
  clk: zte: add i2s clocks for zx296718
  clk: sunxi-ng: sun9i-a80: Fix wrong pointer passed to PTR_ERR()
  clk: sunxi-ng: select SUNXI_CCU_MULT for sun5i
  clk: sunxi-ng: Check kzalloc() for errors and cleanup error path
  clk: tegra: Add BPMP clock driver
  clk: uniphier: add eMMC clock for LD11 and LD20 SoCs
  clk: uniphier: add NAND clock for all UniPhier SoCs
  ARM: dts: sun9i: Switch to new clock bindings
  clk: sunxi-ng: Add A80 Display Engine CCU
  clk: sunxi-ng: Add A80 USB CCU
  clk: sunxi-ng: Add A80 CCU
  clk: sunxi-ng: Support separately grouped PLL lock status register
  clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
  clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
  clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
  clk: qcom: SDHCI enablement on Nexus 5X / 6P
  ...

Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt

@@ -16,7 +16,20 @@ Required properties:
 - #clock-cells:	Should be <1>. The permitted clock-specifier values can be
 		  found in include/dt-bindings/clock/bcm2835.h
 - reg:		Specifies base physical address and size of the registers
-- clocks:	The external oscillator clock phandle
+- clocks:	phandles to the parent clocks used as input to the module, in
+		  the following order:
+
+		  - External oscillator
+		  - DSI0 byte clock
+		  - DSI0 DDR2 clock
+		  - DSI0 DDR clock
+		  - DSI1 byte clock
+		  - DSI1 DDR2 clock
+		  - DSI1 DDR clock
+
+		  Only external oscillator is required.  The DSI clocks may
+		  not be present, in which case their children will be
+		  unusable.
 
 Example:
 

Documentation/devicetree/bindings/clock/exynos4415-clock.txt

-* Samsung Exynos4415 Clock Controller
-
-The Exynos4415 clock controller generates and supplies clock to various
-consumer devices within the Exynos4415 SoC.
-
-Required properties:
-
-- compatible: should be one of the following:
-  - "samsung,exynos4415-cmu" - for the main system clocks controller
-    (CMU_LEFTBUS, CMU_RIGHTBUS, CMU_TOP, CMU_CPU clock domains).
-  - "samsung,exynos4415-cmu-dmc" - for the Exynos4415 SoC DRAM Memory
-    Controller (DMC) domain clock controller.
-
-- reg: physical base address of the controller and length of memory mapped
-  region.
-
-- #clock-cells: should be 1.
-
-Each clock is assigned an identifier and client nodes can use this identifier
-to specify the clock which they consume.
-
-All available clocks are defined as preprocessor macros in
-dt-bindings/clock/exynos4415.h header and can be used in device
-tree sources.
-
-Example 1: An example of a clock controller node is listed below.
-
-	cmu: clock-controller@10030000 {
-		compatible = "samsung,exynos4415-cmu";
-		reg = <0x10030000 0x18000>;
-		#clock-cells = <1>;
-	};
-
-	cmu-dmc: clock-controller@105C0000 {
-		compatible = "samsung,exynos4415-cmu-dmc";
-		reg = <0x105C0000 0x3000>;
-		#clock-cells = <1>;
-	};

Documentation/devicetree/bindings/clock/hi3660-clock.txt

+* Hisilicon Hi3660 Clock Controller
+
+The Hi3660 clock controller generates and supplies clock to various
+controllers within the Hi3660 SoC.
+
+Required Properties:
+
+- compatible: the compatible should be one of the following strings to
+	indicate the clock controller functionality.
+
+	- "hisilicon,hi3660-crgctrl"
+	- "hisilicon,hi3660-pctrl"
+	- "hisilicon,hi3660-pmuctrl"
+	- "hisilicon,hi3660-sctrl"
+	- "hisilicon,hi3660-iomcu"
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- #clock-cells: should be 1.
+
+Each clock is assigned an identifier and client nodes use this identifier
+to specify the clock which they consume.
+
+All these identifier could be found in <dt-bindings/clock/hi3660-clock.h>.
+
+Examples:
+	crg_ctrl: clock-controller@fff35000 {
+		compatible = "hisilicon,hi3660-crgctrl", "syscon";
+		reg = <0x0 0xfff35000 0x0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	uart0: serial@fdf02000 {
+		compatible = "arm,pl011", "arm,primecell";
+		reg = <0x0 0xfdf02000 0x0 0x1000>;
+		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&crg_ctrl HI3660_CLK_MUX_UART0>,
+			 <&crg_ctrl HI3660_PCLK>;
+		clock-names = "uartclk", "apb_pclk";
+		status = "disabled";
+	};

Documentation/devicetree/bindings/clock/idt,versaclock5.txt

+Binding for IDT VersaClock5 programmable i2c clock generator.
+
+The IDT VersaClock5 are programmable i2c clock generators providing
+from 3 to 12 output clocks.
+
+==I2C device node==
+
+Required properties:
+- compatible:	shall be one of "idt,5p49v5923" , "idt,5p49v5933".
+- reg:		i2c device address, shall be 0x68 or 0x6a.
+- #clock-cells:	from common clock binding; shall be set to 1.
+- clocks:	from common clock binding; list of parent clock handles,
+		- 5p49v5923: (required) either or both of XTAL or CLKIN
+					reference clock.
+		- 5p49v5933: (optional) property not present (internal
+					Xtal used) or CLKIN reference
+					clock.
+- clock-names:	from common clock binding; clock input names, can be
+		- 5p49v5923: (required) either or both of "xin", "clkin".
+		- 5p49v5933: (optional) property not present or "clkin".
+
+==Mapping between clock specifier and physical pins==
+
+When referencing the provided clock in the DT using phandle and
+clock specifier, the following mapping applies:
+
+5P49V5923:
+	0 -- OUT0_SEL_I2CB
+	1 -- OUT1
+	2 -- OUT2
+
+5P49V5933:
+	0 -- OUT0_SEL_I2CB
+	1 -- OUT1
+	2 -- OUT4
+
+==Example==
+
+/* 25MHz reference crystal */
+ref25: ref25m {
+	compatible = "fixed-clock";
+	#clock-cells = <0>;
+	clock-frequency = <25000000>;
+};
+
+i2c-master-node {
+
+	/* IDT 5P49V5923 i2c clock generator */
+	vc5: clock-generator@6a {
+		compatible = "idt,5p49v5923";
+		reg = <0x6a>;
+		#clock-cells = <1>;
+
+		/* Connect XIN input to 25MHz reference */
+		clocks = <&ref25m>;
+		clock-names = "xin";
+	};
+};
+
+/* Consumer referencing the 5P49V5923 pin OUT1 */
+consumer {
+	...
+	clocks = <&vc5 1>;
+	...
+}

Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt

@@ -7,6 +7,7 @@ Required properties:
 - compatible : must be "marvell,armada-370-corediv-clock",
 		       "marvell,armada-375-corediv-clock",
 		       "marvell,armada-380-corediv-clock",
+                       "marvell,mv98dx3236-corediv-clock",
 
 - reg : must be the register address of Core Divider control register
 - #clock-cells : from common clock binding; shall be set to 1

Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt

@@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms
 Required properties:
 - compatible : shall be one of the following:
 	"marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP
+	"marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC
 - reg : Address and length of the clock complex register set, followed
         by address and length of the PMU DFS registers
 - #clock-cells : should be set to 1.

Documentation/devicetree/bindings/clock/qcom,rpmcc.txt

@@ -11,6 +11,7 @@ Required properties :
                compatible "qcom,rpmcc" should be also included.
 
 			"qcom,rpmcc-msm8916", "qcom,rpmcc"
+			"qcom,rpmcc-msm8974", "qcom,rpmcc"
 			"qcom,rpmcc-apq8064", "qcom,rpmcc"
 
 - #clock-cells : shall contain 1

Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt

@@ -42,6 +42,10 @@ Required Properties:
 	Domain bindings in
 	Documentation/devicetree/bindings/power/power_domain.txt.
 
+  - #reset-cells: Must be 1
+      - The single reset specifier cell must be the module number, as defined
+	in the datasheet.
+
 
 Examples
 --------
@@ -55,6 +59,7 @@ Examples
 		clock-names = "extal", "extalr";
 		#clock-cells = <2>;
 		#power-domain-cells = <0>;
+		#reset-cells = <1>;
 	};
 
 
@@ -69,5 +74,6 @@ Examples
 		dmas = <&dmac1 0x13>, <&dmac1 0x12>;
 		dma-names = "tx", "rx";
 		power-domains = <&cpg>;
+		resets = <&cpg 310>;
 		status = "disabled";
 	};

Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt

+* Rockchip RK3328 Clock and Reset Unit
+
+The RK3328 clock controller generates and supplies clock to various
+controllers within the SoC and also implements a reset controller for SoC
+peripherals.
+
+Required Properties:
+
+- compatible: should be "rockchip,rk3328-cru"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- #clock-cells: should be 1.
+- #reset-cells: should be 1.
+
+Optional Properties:
+
+- rockchip,grf: phandle to the syscon managing the "general register files"
+  If missing pll rates are not changeable, due to the missing pll lock status.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. All available clocks are defined as
+preprocessor macros in the dt-bindings/clock/rk3328-cru.h headers and can be
+used in device tree sources. Similar macros exist for the reset sources in
+these files.
+
+External clocks:
+
+There are several clocks that are generated outside the SoC. It is expected
+that they are defined using standard clock bindings with following
+clock-output-names:
+ - "xin24m" - crystal input - required,
+ - "clkin_i2s" - external I2S clock - optional,
+ - "gmac_clkin" - external GMAC clock - optional
+ - "phy_50m_out" - output clock of the pll in the mac phy
+
+Example: Clock controller node:
+
+	cru: clock-controller@ff440000 {
+		compatible = "rockchip,rk3328-cru";
+		reg = <0x0 0xff440000 0x0 0x1000>;
+		rockchip,grf = <&grf>;
+
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+Example: UART controller node that consumes the clock generated by the clock
+  controller:
+
+	uart0: serial@ff120000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0xff120000 0x100>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clocks = <&cru SCLK_UART0>;
+	};

Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt

@@ -13,6 +13,12 @@ Required Properties:
 - #clock-cells: should be 1.
 - #reset-cells: should be 1.
 
+Optional Properties:
+
+- rockchip,grf: phandle to the syscon managing the "general register files".
+  It is used for GRF muxes, if missing any muxes present in the GRF will not
+  be available.
+
 Each clock is assigned an identifier and client nodes can use this identifier
 to specify the clock which they consume. All available clocks are defined as
 preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be

Documentation/devicetree/bindings/clock/st,stm32-rcc.txt

@@ -10,6 +10,7 @@ Required properties:
 - compatible: Should be:
   "st,stm32f42xx-rcc"
   "st,stm32f469-rcc"
+  "st,stm32f746-rcc"
 - reg: should be register base and length as documented in the
   datasheet
 - #reset-cells: 1, see below
@@ -84,6 +85,25 @@ The secondary index is bound with the following magic numbers:
 	12	CLK_I2SQ_PDIV	(post divisor of pll i2s q divisor)
 	13	CLK_SAIQ_PDIV	(post divisor of pll sai q divisor)
 
+	14	CLK_HSI		(Internal ocscillator clock)
+	15	CLK_SYSCLK	(System Clock)
+	16	CLK_HDMI_CEC	(HDMI-CEC clock)
+	17	CLK_SPDIF	(SPDIF-Rx clock)
+	18	CLK_USART1	(U(s)arts clocks)
+	19	CLK_USART2
+	20	CLK_USART3
+	21	CLK_UART4
+	22	CLK_UART5
+	23	CLK_USART6
+	24	CLK_UART7
+	25	CLK_UART8
+	26	CLK_I2C1	(I2S clocks)
+	27	CLK_I2C2
+	28	CLK_I2C3
+	29	CLK_I2C4
+	30	CLK_LPTIMER	(LPTimer1 clock)
+)
+
 Example:
 
 	/* Misc clock, FCLK */

Documentation/devicetree/bindings/clock/stericsson,abx500.txt

+Clock bindings for ST-Ericsson ABx500 clocks
+
+Required properties :
+- compatible : shall contain the following:
+  "stericsson,ab8500-clk"
+- #clock-cells should be <1>
+
+The ABx500 clocks need to be placed as a subnode of an AB8500
+device node, see mfd/ab8500.txt
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/ste-ab8500.h header and can be used in device
+tree sources.
+
+Example:
+
+clock-controller {
+	compatible = "stericsson,ab8500-clk";
+	#clock-cells = <1>;
+};

Documentation/devicetree/bindings/clock/sun9i-de.txt

+Allwinner A80 Display Engine Clock Control Binding
+--------------------------------------------------
+
+Required properties :
+- compatible: must contain one of the following compatibles:
+		- "allwinner,sun9i-a80-de-clks"
+
+- reg: Must contain the registers base address and length
+- clocks: phandle to the clocks feeding the display engine subsystem.
+	  Three are needed:
+  - "mod": the display engine module clock
+  - "dram": the DRAM bus clock for the system
+  - "bus": the bus clock for the whole display engine subsystem
+- clock-names: Must contain the clock names described just above
+- resets: phandle to the reset control for the display engine subsystem.
+- #clock-cells : must contain 1
+- #reset-cells : must contain 1
+
+Example:
+de_clocks: clock@3000000 {
+	compatible = "allwinner,sun9i-a80-de-clks";
+	reg = <0x03000000 0x30>;
+	clocks = <&ccu CLK_DE>, <&ccu CLK_SDRAM>, <&ccu CLK_BUS_DE>;
+	clock-names = "mod", "dram", "bus";
+	resets = <&ccu RST_BUS_DE>;
+	#clock-cells = <1>;
+	#reset-cells = <1>;
+};

Documentation/devicetree/bindings/clock/sun9i-usb.txt

+Allwinner A80 USB Clock Control Binding
+---------------------------------------
+
+Required properties :
+- compatible: must contain one of the following compatibles:
+		- "allwinner,sun9i-a80-usb-clocks"
+
+- reg: Must contain the registers base address and length
+- clocks: phandle to the clocks feeding the USB subsystem. Two are needed:
+  - "bus": the bus clock for the whole USB subsystem
+  - "hosc": the high frequency oscillator (usually at 24MHz)
+- clock-names: Must contain the clock names described just above
+- #clock-cells : must contain 1
+- #reset-cells : must contain 1
+
+Example:
+usb_clocks: clock@a08000 {
+	compatible = "allwinner,sun9i-a80-usb-clks";
+	reg = <0x00a08000 0x8>;
+	clocks = <&ccu CLK_BUS_USB>, <&osc24M>;
+	clock-names = "bus", "hosc";
+	#clock-cells = <1>;
+	#reset-cells = <1>;
+};

Documentation/devicetree/bindings/clock/sunxi-ccu.txt

@@ -7,6 +7,8 @@ Required properties :
 		- "allwinner,sun8i-a23-ccu"
 		- "allwinner,sun8i-a33-ccu"
 		- "allwinner,sun8i-h3-ccu"
+		- "allwinner,sun8i-v3s-ccu"
+		- "allwinner,sun9i-a80-ccu"
 		- "allwinner,sun50i-a64-ccu"
 
 - reg: Must contain the registers base address and length

Documentation/devicetree/bindings/clock/ti,cdce925.txt

-Binding for TO CDCE925 programmable I2C clock synthesizers.
+Binding for TI CDCE913/925/937/949 programmable I2C clock synthesizers.
 
 Reference
 This binding uses the common clock binding[1].
 
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] http://www.ti.com/product/cdce925
+[2] http://www.ti.com/product/cdce913
+[3] http://www.ti.com/product/cdce925
+[4] http://www.ti.com/product/cdce937
+[5] http://www.ti.com/product/cdce949
 
 The driver provides clock sources for each output Y1 through Y5.
 
 Required properties:
- - compatible: Shall be "ti,cdce925"
+ - compatible: Shall be one of the following:
+	- "ti,cdce913": 1-PLL, 3 Outputs
+	- "ti,cdce925": 2-PLL, 5 Outputs
+	- "ti,cdce937": 3-PLL, 7 Outputs
+	- "ti,cdce949": 4-PLL, 9 Outputs
  - reg: I2C device address.
  - clocks: Points to a fixed parent clock that provides the input frequency.
  - #clock-cells: From common clock bindings: Shall be 1.
@@ -18,7 +25,7 @@ Optional properties:
  - xtal-load-pf: Crystal load-capacitor value to fine-tune performance on a
                  board, or to compensate for external influences.
 
-For both PLL1 and PLL2 an optional child node can be used to specify spread
+For all PLL1, PLL2, ... an optional child node can be used to specify spread
 spectrum clocking parameters for a board.
   - spread-spectrum: SSC mode as defined in the data sheet.
   - spread-spectrum-center: Use "centered" mode instead of "max" mode. When

Documentation/devicetree/bindings/clock/zx296718-clk.txt

@@ -13,6 +13,9 @@ Required properties:
 	"zte,zx296718-lsp1crm":
 		zx296718 device level clock selection and gating
 
+	"zte,zx296718-audiocrm":
+		zx296718 audio clock selection, divider and gating
+
 - reg: Address and length of the register set
 
 The clock consumer should specify the desired clock by having the clock

MAINTAINERS

@@ -6270,6 +6270,11 @@ S:	Maintained
 F:	drivers/mfd/lpc_ich.c
 F:	drivers/gpio/gpio-ich.c
 
+IDT VersaClock 5 CLOCK DRIVER
+M:	Marek Vasut <marek.vasut@gmail.com>
+S:	Maintained
+F:	drivers/clk/clk-versaclock5.c
+
 IDE SUBSYSTEM
 M:	"David S. Miller" <davem@davemloft.net>
 L:	linux-ide@vger.kernel.org

arch/arm/boot/dts/sun5i-a10s.dtsi

@@ -65,8 +65,9 @@ framebuffer@0 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-hdmi";
-			clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
-				 <&ahb_gates 43>, <&ahb_gates 44>;
+			clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_HDMI>,
+				 <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DRAM_DE_BE>,
+				 <&ccu CLK_DE_BE>, <&ccu CLK_HDMI>;
 			status = "disabled";
 		};
 
@@ -74,8 +75,8 @@ framebuffer@1 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0";
-			clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
-				 <&ahb_gates 44>;
+			clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_TCON_CH0>, <&ccu CLK_DRAM_DE_BE>;
 			status = "disabled";
 		};
 
@@ -83,77 +84,19 @@ framebuffer@2 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-tve0";
-			clocks = <&pll3>, <&pll5 1>, <&ahb_gates 34>,
-				 <&ahb_gates 36>, <&ahb_gates 44>;
+			clocks = <&ccu CLK_AHB_TVE>, <&ccu CLK_AHB_LCD>,
+				 <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_TCON_CH1>, <&ccu CLK_DRAM_DE_BE>;
 			status = "disabled";
 		};
 	};
 
-	clocks {
-		ahb_gates: clk@01c20060 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a10s-ahb-gates-clk";
-			reg = <0x01c20060 0x8>;
-			clocks = <&ahb>;
-			clock-indices = <0>, <1>,
-					<2>, <5>, <6>,
-					<7>, <8>, <9>,
-					<10>, <13>,
-					<14>, <17>, <18>,
-					<20>, <21>, <22>,
-					<26>, <28>, <32>,
-					<34>, <36>, <40>,
-					<43>, <44>,
-					<46>, <51>,
-					<52>;
-			clock-output-names = "ahb_usbotg", "ahb_ehci",
-					     "ahb_ohci", "ahb_ss", "ahb_dma",
-					     "ahb_bist", "ahb_mmc0", "ahb_mmc1",
-					     "ahb_mmc2", "ahb_nand",
-					     "ahb_sdram", "ahb_emac", "ahb_ts",
-					     "ahb_spi0", "ahb_spi1", "ahb_spi2",
-					     "ahb_gps", "ahb_stimer", "ahb_ve",
-					     "ahb_tve", "ahb_lcd", "ahb_csi",
-					     "ahb_hdmi", "ahb_de_be",
-					     "ahb_de_fe", "ahb_iep",
-					     "ahb_mali400";
-		};
-
-		apb0_gates: clk@01c20068 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a10s-apb0-gates-clk";
-			reg = <0x01c20068 0x4>;
-			clocks = <&apb0>;
-			clock-indices = <0>, <3>,
-					<5>, <6>,
-					<10>;
-			clock-output-names = "apb0_codec", "apb0_iis",
-					     "apb0_pio", "apb0_ir",
-					     "apb0_keypad";
-		};
-
-		apb1_gates: clk@01c2006c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a10s-apb1-gates-clk";
-			reg = <0x01c2006c 0x4>;
-			clocks = <&apb1>;
-			clock-indices = <0>, <1>,
-					<2>, <16>,
-					<17>, <18>,
-					<19>;
-			clock-output-names = "apb1_i2c0", "apb1_i2c1",
-					     "apb1_i2c2", "apb1_uart0",
-					     "apb1_uart1", "apb1_uart2",
-					     "apb1_uart3";
-		};
-	};
-
 	soc@01c00000 {
 		emac: ethernet@01c0b000 {
 			compatible = "allwinner,sun4i-a10-emac";
 			reg = <0x01c0b000 0x1000>;
 			interrupts = <55>;
-			clocks = <&ahb_gates 17>;
+			clocks = <&ccu CLK_AHB_EMAC>;
 			allwinner,sram = <&emac_sram 1>;
 			status = "disabled";
 		};
@@ -169,7 +112,7 @@ mdio: mdio@01c0b080 {
 		pwm: pwm@01c20e00 {
 			compatible = "allwinner,sun5i-a10s-pwm";
 			reg = <0x01c20e00 0xc>;
-			clocks = <&osc24M>;
+			clocks = <&ccu CLK_HOSC>;
 			#pwm-cells = <3>;
 			status = "disabled";
 		};
@@ -180,7 +123,7 @@ uart0: serial@01c28000 {
 			interrupts = <1>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 16>;
+			clocks = <&ccu CLK_APB1_UART0>;
 			status = "disabled";
 		};
 
@@ -190,12 +133,16 @@ uart2: serial@01c28800 {
 			interrupts = <3>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 18>;
+			clocks = <&ccu CLK_APB1_UART2>;
 			status = "disabled";
 		};
 	};
 };
 
+&ccu {
+	compatible = "allwinner,sun5i-a10s-ccu";
+};
+
 &pio {
 	compatible = "allwinner,sun5i-a10s-pinctrl";
 

arch/arm/boot/dts/sun5i-a13.dtsi

@@ -61,8 +61,8 @@ framebuffer@0 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0";
-			clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&de_be_clk>,
-				 <&tcon_ch0_clk>, <&dram_gates 26>;
+			clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_TCON_CH0>, <&ccu CLK_DRAM_DE_BE>;
 			status = "disabled";
 		};
 	};
@@ -99,114 +99,6 @@ cpu_crit: cpu_crit {
 		};
 	};
 
-	clocks {
-		ahb_gates: clk@01c20060 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-ahb-gates-clk";
-			reg = <0x01c20060 0x8>;
-			clocks = <&ahb>;
-			clock-indices = <0>, <1>,
-					<2>, <5>, <6>,
-					<7>, <8>, <9>,
-					<10>, <13>,
-					<14>, <20>,
-					<21>, <22>,
-					<28>, <32>, <34>,
-					<36>, <40>, <44>,
-					<46>, <51>,
-					<52>;
-			clock-output-names = "ahb_usbotg", "ahb_ehci",
-					     "ahb_ohci", "ahb_ss", "ahb_dma",
-					     "ahb_bist", "ahb_mmc0", "ahb_mmc1",
-					     "ahb_mmc2", "ahb_nand",
-					     "ahb_sdram", "ahb_spi0",
-					     "ahb_spi1", "ahb_spi2",
-					     "ahb_stimer", "ahb_ve", "ahb_tve",
-					     "ahb_lcd", "ahb_csi", "ahb_de_be",
-					     "ahb_de_fe", "ahb_iep",
-					     "ahb_mali400";
-		};
-
-		apb0_gates: clk@01c20068 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-apb0-gates-clk";
-			reg = <0x01c20068 0x4>;
-			clocks = <&apb0>;
-			clock-indices = <0>, <5>,
-					<6>;
-			clock-output-names = "apb0_codec", "apb0_pio",
-					     "apb0_ir";
-		};
-
-		apb1_gates: clk@01c2006c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-apb1-gates-clk";
-			reg = <0x01c2006c 0x4>;
-			clocks = <&apb1>;
-			clock-indices = <0>, <1>,
-					<2>, <17>,
-					<19>;
-			clock-output-names = "apb1_i2c0", "apb1_i2c1",
-					     "apb1_i2c2", "apb1_uart1",
-					     "apb1_uart3";
-		};
-
-		dram_gates: clk@01c20100 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-dram-gates-clk",
-				     "allwinner,sun4i-a10-gates-clk";
-			reg = <0x01c20100 0x4>;
-			clocks = <&pll5 0>;
-			clock-indices = <0>,
-					<1>,
-					<25>,
-					<26>,
-					<29>,
-					<31>;
-			clock-output-names = "dram_ve",
-					     "dram_csi",
-					     "dram_de_fe",
-					     "dram_de_be",
-					     "dram_ace",
-					     "dram_iep";
-		};
-
-		de_be_clk: clk@01c20104 {
-			#clock-cells = <0>;
-			#reset-cells = <0>;
-			compatible = "allwinner,sun4i-a10-display-clk";
-			reg = <0x01c20104 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll5 1>;
-			clock-output-names = "de-be";
-		};
-
-		de_fe_clk: clk@01c2010c {
-			#clock-cells = <0>;
-			#reset-cells = <0>;
-			compatible = "allwinner,sun4i-a10-display-clk";
-			reg = <0x01c2010c 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll5 1>;
-			clock-output-names = "de-fe";
-		};
-
-		tcon_ch0_clk: clk@01c20118 {
-			#clock-cells = <0>;
-			#reset-cells = <1>;
-			compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
-			reg = <0x01c20118 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
-			clock-output-names = "tcon-ch0-sclk";
-		};
-
-		tcon_ch1_clk: clk@01c2012c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
-			reg = <0x01c2012c 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
-			clock-output-names = "tcon-ch1-sclk";
-		};
-	};
-
 	display-engine {
 		compatible = "allwinner,sun5i-a13-display-engine";
 		allwinner,pipelines = <&fe0>;
@@ -217,11 +109,11 @@ tcon0: lcd-controller@01c0c000 {
 			compatible = "allwinner,sun5i-a13-tcon";
 			reg = <0x01c0c000 0x1000>;
 			interrupts = <44>;
-			resets = <&tcon_ch0_clk 1>;
+			resets = <&ccu RST_LCD>;
 			reset-names = "lcd";
-			clocks = <&ahb_gates 36>,
-				 <&tcon_ch0_clk>,
-				 <&tcon_ch1_clk>;
+			clocks = <&ccu CLK_AHB_LCD>,
+				 <&ccu CLK_TCON_CH0>,
+				 <&ccu CLK_TCON_CH1>;
 			clock-names = "ahb",
 				      "tcon-ch0",
 				      "tcon-ch1";
@@ -254,7 +146,7 @@ tcon0_out: port@1 {
 		pwm: pwm@01c20e00 {
 			compatible = "allwinner,sun5i-a13-pwm";
 			reg = <0x01c20e00 0xc>;
-			clocks = <&osc24M>;
+			clocks = <&ccu CLK_HOSC>;
 			#pwm-cells = <3>;
 			status = "disabled";
 		};
@@ -263,11 +155,11 @@ fe0: display-frontend@01e00000 {
 			compatible = "allwinner,sun5i-a13-display-frontend";
 			reg = <0x01e00000 0x20000>;
 			interrupts = <47>;
-			clocks = <&ahb_gates 46>, <&de_fe_clk>,
-				 <&dram_gates 25>;
+			clocks = <&ccu CLK_DE_FE>, <&ccu CLK_DE_FE>,
+				 <&ccu CLK_DRAM_DE_FE>;
 			clock-names = "ahb", "mod",
 				      "ram";
-			resets = <&de_fe_clk>;
+			resets = <&ccu RST_DE_FE>;
 			status = "disabled";
 
 			ports {
@@ -290,14 +182,14 @@ fe0_out_be0: endpoint@0 {
 		be0: display-backend@01e60000 {
 			compatible = "allwinner,sun5i-a13-display-backend";
 			reg = <0x01e60000 0x10000>;
-			clocks = <&ahb_gates 44>, <&de_be_clk>,
-				 <&dram_gates 26>;
+			clocks = <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_DRAM_DE_BE>;
 			clock-names = "ahb", "mod",
 				      "ram";
-			resets = <&de_be_clk>;
+			resets = <&ccu RST_DE_BE>;
 			status = "disabled";
 
-			assigned-clocks = <&de_be_clk>;
+			assigned-clocks = <&ccu CLK_DE_BE>;
 			assigned-clock-rates = <300000000>;
 
 			ports {
@@ -330,6 +222,10 @@ be0_out_tcon0: endpoint@0 {
 	};
 };
 
+&ccu {
+	compatible = "allwinner,sun5i-a13-ccu";
+};
+
 &cpu0 {
 	clock-latency = <244144>; /* 8 32k periods */
 	operating-points = <

arch/arm/boot/dts/sun5i-r8.dtsi

@@ -51,9 +51,9 @@ framebuffer@1 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-tve0";
-			clocks = <&ahb_gates 34>, <&ahb_gates 36>,
-				 <&ahb_gates 44>, <&de_be_clk>,
-				 <&tcon_ch1_clk>, <&dram_gates 26>;
+			clocks = <&ccu CLK_AHB_TVE>, <&ccu CLK_AHB_LCD>,
+				 <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_TCON_CH1>, <&ccu CLK_DRAM_DE_BE>;
 			status = "disabled";
 		};
 	};
@@ -62,8 +62,8 @@ soc@01c00000 {
 		tve0: tv-encoder@01c0a000 {
 			compatible = "allwinner,sun4i-a10-tv-encoder";
 			reg = <0x01c0a000 0x1000>;
-			clocks = <&ahb_gates 34>;
-			resets = <&tcon_ch0_clk 0>;
+			clocks = <&ccu CLK_AHB_TVE>;
+			resets = <&ccu RST_TVE>;
 			status = "disabled";
 
 			port {

arch/x86/Kconfig

@@ -2787,10 +2787,6 @@ config X86_DMA_REMAP
 	bool
 	depends on STA2X11
 
-config PMC_ATOM
-	def_bool y
-        depends on PCI
-
 source "net/Kconfig"
 
 source "drivers/Kconfig"

arch/x86/platform/atom/Makefile

-obj-$(CONFIG_PMC_ATOM)		+= pmc_atom.o
 obj-$(CONFIG_PUNIT_ATOM_DEBUG)	+= punit_atom_debug.o

drivers/acpi/acpi_lpss.c

@@ -18,6 +18,7 @@
 #include <linux/mutex.h>
 #include <linux/platform_device.h>
 #include <linux/platform_data/clk-lpss.h>
+#include <linux/platform_data/x86/pmc_atom.h>
 #include <linux/pm_domain.h>
 #include <linux/pm_runtime.h>
 #include <linux/delay.h>
@@ -31,7 +32,6 @@ ACPI_MODULE_NAME("acpi_lpss");
 #include <asm/cpu_device_id.h>
 #include <asm/intel-family.h>
 #include <asm/iosf_mbi.h>
-#include <asm/pmc_atom.h>
 
 #define LPSS_ADDR(desc) ((unsigned long)&desc)
 

drivers/clk/Kconfig

@@ -95,16 +95,17 @@ config COMMON_CLK_CDCE706
 	  This driver supports TI CDCE706 programmable 3-PLL clock synthesizer.
 
 config COMMON_CLK_CDCE925
-	tristate "Clock driver for TI CDCE925 devices"
+	tristate "Clock driver for TI CDCE913/925/937/949 devices"
 	depends on I2C
 	depends on OF
 	select REGMAP_I2C
 	help
 	---help---
-	  This driver supports the TI CDCE925 programmable clock synthesizer.
-	  The chip contains two PLLs with spread-spectrum clocking support and
-	  five output dividers. The driver only supports the following setup,
-	  and uses a fixed setting for the output muxes.
+	  This driver supports the TI CDCE913/925/937/949 programmable clock
+	  synthesizer. Each chip has different number of PLLs and outputs.
+	  For example, the CDCE925 contains two PLLs with spread-spectrum
+	  clocking support and five output dividers. The driver only supports
+	  the following setup, and uses a fixed setting for the output muxes.
 	  Y1 is derived from the input clock
 	  Y2 and Y3 derive from PLL1
 	  Y4 and Y5 derive from PLL2
@@ -198,6 +199,16 @@ config COMMON_CLK_OXNAS
 	---help---
 	  Support for the OXNAS SoC Family clocks.
 
+config COMMON_CLK_VC5
+	tristate "Clock driver for IDT VersaClock5 devices"
+	depends on I2C
+	depends on OF
+	select REGMAP_I2C
+	help
+	---help---
+	  This driver supports the IDT VersaClock5 programmable clock
+	  generator.
+
 source "drivers/clk/bcm/Kconfig"
 source "drivers/clk/hisilicon/Kconfig"
 source "drivers/clk/mediatek/Kconfig"

drivers/clk/Makefile

@@ -46,6 +46,7 @@ obj-$(CONFIG_ARCH_TANGO)		+= clk-tango4.o
 obj-$(CONFIG_CLK_TWL6040)		+= clk-twl6040.o
 obj-$(CONFIG_ARCH_U300)			+= clk-u300.o
 obj-$(CONFIG_ARCH_VT8500)		+= clk-vt8500.o
+obj-$(CONFIG_COMMON_CLK_VC5)		+= clk-versaclock5.o
 obj-$(CONFIG_COMMON_CLK_WM831X)		+= clk-wm831x.o
 obj-$(CONFIG_COMMON_CLK_XGENE)		+= clk-xgene.o
 
@@ -87,6 +88,8 @@ obj-y					+= ti/
 obj-$(CONFIG_CLK_UNIPHIER)		+= uniphier/
 obj-$(CONFIG_ARCH_U8500)		+= ux500/
 obj-$(CONFIG_COMMON_CLK_VERSATILE)	+= versatile/
+ifeq ($(CONFIG_COMMON_CLK), y)
 obj-$(CONFIG_X86)			+= x86/
+endif
 obj-$(CONFIG_ARCH_ZX)			+= zte/
 obj-$(CONFIG_ARCH_ZYNQ)			+= zynq/

drivers/clk/axs10x/i2s_pll_clock.c

@@ -182,6 +182,7 @@ static int i2s_pll_clk_probe(struct platform_device *pdev)
 	if (IS_ERR(pll_clk->base))
 		return PTR_ERR(pll_clk->base);
 
+	memset(&init, 0, sizeof(init));
 	clk_name = node->name;
 	init.name = clk_name;
 	init.ops = &i2s_pll_ops;

drivers/clk/clk-cdce925.c

 /*
- * Driver for TI Dual PLL CDCE925 clock synthesizer
+ * Driver for TI Multi PLL CDCE913/925/937/949 clock synthesizer
  *
- * This driver always connects the Y1 to the input clock, Y2/Y3 to PLL1
- * and Y4/Y5 to PLL2. PLL frequency is set on a first-come-first-serve
+ * This driver always connects the Y1 to the input clock, Y2/Y3 to PLL1,
+ * Y4/Y5 to PLL2, and so on. PLL frequency is set on a first-come-first-serve
  * basis. Clients can directly request any frequency that the chip can
  * deliver using the standard clk framework. In addition, the device can
  * be configured and activated via the devicetree.
@@ -19,11 +19,32 @@
 #include <linux/slab.h>
 #include <linux/gcd.h>
 
-/* The chip has 2 PLLs which can be routed through dividers to 5 outputs.
+/* Each chip has different number of PLLs and outputs, for example:
+ * The CECE925 has 2 PLLs which can be routed through dividers to 5 outputs.
  * Model this as 2 PLL clocks which are parents to the outputs.
  */
-#define NUMBER_OF_PLLS	2
-#define NUMBER_OF_OUTPUTS	5
+
+enum {
+	CDCE913,
+	CDCE925,
+	CDCE937,
+	CDCE949,
+};
+
+struct clk_cdce925_chip_info {
+	int num_plls;
+	int num_outputs;
+};
+
+static const struct clk_cdce925_chip_info clk_cdce925_chip_info_tbl[] = {
+	[CDCE913] = { .num_plls = 1, .num_outputs = 3 },
+	[CDCE925] = { .num_plls = 2, .num_outputs = 5 },
+	[CDCE937] = { .num_plls = 3, .num_outputs = 7 },
+	[CDCE949] = { .num_plls = 4, .num_outputs = 9 },
+};
+
+#define MAX_NUMBER_OF_PLLS	4
+#define MAX_NUMBER_OF_OUTPUTS	9
 
 #define CDCE925_REG_GLOBAL1	0x01
 #define CDCE925_REG_Y1SPIPDIVH	0x02
@@ -43,7 +64,7 @@ struct clk_cdce925_output {
 	struct clk_hw hw;
 	struct clk_cdce925_chip *chip;
 	u8 index;
-	u16 pdiv; /* 1..127 for Y2-Y5; 1..1023 for Y1 */
+	u16 pdiv; /* 1..127 for Y2-Y9; 1..1023 for Y1 */
 };
 #define to_clk_cdce925_output(_hw) \
 	container_of(_hw, struct clk_cdce925_output, hw)
@@ -60,8 +81,9 @@ struct clk_cdce925_pll {
 struct clk_cdce925_chip {
 	struct regmap *regmap;
 	struct i2c_client *i2c_client;
-	struct clk_cdce925_pll pll[NUMBER_OF_PLLS];
-	struct clk_cdce925_output clk[NUMBER_OF_OUTPUTS];
+	const struct clk_cdce925_chip_info *chip_info;
+	struct clk_cdce925_pll pll[MAX_NUMBER_OF_PLLS];
+	struct clk_cdce925_output clk[MAX_NUMBER_OF_OUTPUTS];
 };
 
 /* ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** */
@@ -284,6 +306,18 @@ static void cdce925_clk_set_pdiv(struct clk_cdce925_output *data, u16 pdiv)
 	case 4:
 		regmap_update_bits(data->chip->regmap, 0x27, 0x7F, pdiv);
 		break;
+	case 5:
+		regmap_update_bits(data->chip->regmap, 0x36, 0x7F, pdiv);
+		break;
+	case 6:
+		regmap_update_bits(data->chip->regmap, 0x37, 0x7F, pdiv);
+		break;
+	case 7:
+		regmap_update_bits(data->chip->regmap, 0x46, 0x7F, pdiv);
+		break;
+	case 8:
+		regmap_update_bits(data->chip->regmap, 0x47, 0x7F, pdiv);
+		break;
 	}
 }
 
@@ -302,6 +336,14 @@ static void cdce925_clk_activate(struct clk_cdce925_output *data)
 	case 4:
 		regmap_update_bits(data->chip->regmap, 0x24, 0x03, 0x03);
 		break;
+	case 5:
+	case 6:
+		regmap_update_bits(data->chip->regmap, 0x34, 0x03, 0x03);
+		break;
+	case 7:
+	case 8:
+		regmap_update_bits(data->chip->regmap, 0x44, 0x03, 0x03);
+		break;
 	}
 }
 
@@ -474,15 +516,6 @@ static const struct clk_ops cdce925_clk_y1_ops = {
 	.set_rate = cdce925_clk_y1_set_rate,
 };
 
-
-static struct regmap_config cdce925_regmap_config = {
-	.name = "configuration0",
-	.reg_bits = 8,
-	.val_bits = 8,
-	.cache_type = REGCACHE_RBTREE,
-	.max_register = 0x2F,
-};
-
 #define CDCE925_I2C_COMMAND_BLOCK_TRANSFER	0x00
 #define CDCE925_I2C_COMMAND_BYTE_TRANSFER	0x80
 
@@ -582,13 +615,19 @@ static int cdce925_probe(struct i2c_client *client,
 	struct clk_cdce925_chip *data;
 	struct device_node *node = client->dev.of_node;
 	const char *parent_name;
-	const char *pll_clk_name[NUMBER_OF_PLLS] = {NULL,};
+	const char *pll_clk_name[MAX_NUMBER_OF_PLLS] = {NULL,};
 	struct clk_init_data init;
 	u32 value;
 	int i;
 	int err;
 	struct device_node *np_output;
 	char child_name[6];
+	struct regmap_config config = {
+		.name = "configuration0",
+		.reg_bits = 8,
+		.val_bits = 8,
+		.cache_type = REGCACHE_RBTREE,
+	};
 
 	dev_dbg(&client->dev, "%s\n", __func__);
 	data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
@@ -596,8 +635,11 @@ static int cdce925_probe(struct i2c_client *client,
 		return -ENOMEM;
 
 	data->i2c_client = client;
+	data->chip_info = &clk_cdce925_chip_info_tbl[id->driver_data];
+	config.max_register = CDCE925_OFFSET_PLL +
+		data->chip_info->num_plls * 0x10 - 1;
 	data->regmap = devm_regmap_init(&client->dev, &regmap_cdce925_bus,
-			&client->dev, &cdce925_regmap_config);
+			&client->dev, &config);
 	if (IS_ERR(data->regmap)) {
 		dev_err(&client->dev, "failed to allocate register map\n");
 		return PTR_ERR(data->regmap);
@@ -626,7 +668,7 @@ static int cdce925_probe(struct i2c_client *client,
 	init.num_parents = parent_name ? 1 : 0;
 
 	/* Register PLL clocks */
-	for (i = 0; i < NUMBER_OF_PLLS; ++i) {
+	for (i = 0; i < data->chip_info->num_plls; ++i) {
 		pll_clk_name[i] = kasprintf(GFP_KERNEL, "%s.pll%d",
 			client->dev.of_node->name, i);
 		init.name = pll_clk_name[i];
@@ -684,7 +726,7 @@ static int cdce925_probe(struct i2c_client *client,
 	init.ops = &cdce925_clk_ops;
 	init.flags = CLK_SET_RATE_PARENT;
 	init.num_parents = 1;
-	for (i = 1; i < NUMBER_OF_OUTPUTS; ++i) {
+	for (i = 1; i < data->chip_info->num_outputs; ++i) {
 		init.name = kasprintf(GFP_KERNEL, "%s.Y%d",
 			client->dev.of_node->name, i+1);
 		data->clk[i].chip = data;
@@ -702,6 +744,16 @@ static int cdce925_probe(struct i2c_client *client,
 			/* Mux Y4/5 to PLL2 */
 			init.parent_names = &pll_clk_name[1];
 			break;
+		case 5:
+		case 6:
+			/* Mux Y6/7 to PLL3 */
+			init.parent_names = &pll_clk_name[2];
+			break;
+		case 7:
+		case 8:
+			/* Mux Y8/9 to PLL4 */
+			init.parent_names = &pll_clk_name[3];
+			break;
 		}
 		err = devm_clk_hw_register(&client->dev, &data->clk[i].hw);
 		kfree(init.name); /* clock framework made a copy of the name */
@@ -720,7 +772,7 @@ static int cdce925_probe(struct i2c_client *client,
 	err = 0;
 
 error:
-	for (i = 0; i < NUMBER_OF_PLLS; ++i)
+	for (i = 0; i < data->chip_info->num_plls; ++i)
 		/* clock framework made a copy of the name */
 		kfree(pll_clk_name[i]);
 
@@ -728,13 +780,19 @@ static int cdce925_probe(struct i2c_client *client,
 }
 
 static const struct i2c_device_id cdce925_id[] = {
-	{ "cdce925", 0 },
+	{ "cdce913", CDCE913 },
+	{ "cdce925", CDCE925 },
+	{ "cdce937", CDCE937 },
+	{ "cdce949", CDCE949 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, cdce925_id);
 
 static const struct of_device_id clk_cdce925_of_match[] = {
+	{ .compatible = "ti,cdce913" },
 	{ .compatible = "ti,cdce925" },
+	{ .compatible = "ti,cdce937" },
+	{ .compatible = "ti,cdce949" },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, clk_cdce925_of_match);
@@ -750,5 +808,5 @@ static struct i2c_driver cdce925_driver = {
 module_i2c_driver(cdce925_driver);
 
 MODULE_AUTHOR("Mike Looijmans <mike.looijmans@topic.nl>");
-MODULE_DESCRIPTION("cdce925 driver");
+MODULE_DESCRIPTION("TI CDCE913/925/937/949 driver");
 MODULE_LICENSE("GPL");

drivers/clk/clk-conf.c

@@ -40,8 +40,9 @@ static int __set_clk_parents(struct device_node *node, bool clk_supplier)
 			return 0;
 		pclk = of_clk_get_from_provider(&clkspec);
 		if (IS_ERR(pclk)) {
-			pr_warn("clk: couldn't get parent clock %d for %s\n",
-				index, node->full_name);
+			if (PTR_ERR(pclk) != -EPROBE_DEFER)
+				pr_warn("clk: couldn't get parent clock %d for %s\n",
+					index, node->full_name);
 			return PTR_ERR(pclk);
 		}
 
@@ -55,8 +56,9 @@ static int __set_clk_parents(struct device_node *node, bool clk_supplier)
 		}
 		clk = of_clk_get_from_provider(&clkspec);
 		if (IS_ERR(clk)) {
-			pr_warn("clk: couldn't get assigned clock %d for %s\n",
-				index, node->full_name);
+			if (PTR_ERR(clk) != -EPROBE_DEFER)
+				pr_warn("clk: couldn't get assigned clock %d for %s\n",
+					index, node->full_name);
 			rc = PTR_ERR(clk);
 			goto err;
 		}
@@ -99,8 +101,9 @@ static int __set_clk_rates(struct device_node *node, bool clk_supplier)
 
 			clk = of_clk_get_from_provider(&clkspec);
 			if (IS_ERR(clk)) {
-				pr_warn("clk: couldn't get clock %d for %s\n",
-					index, node->full_name);
+				if (PTR_ERR(clk) != -EPROBE_DEFER)
+					pr_warn("clk: couldn't get clock %d for %s\n",
+						index, node->full_name);
 				return PTR_ERR(clk);
 			}
 

drivers/clk/clk-cs2000-cp.c

@@ -59,6 +59,10 @@ struct cs2000_priv {
 	struct i2c_client *client;
 	struct clk *clk_in;
 	struct clk *ref_clk;
+
+	/* suspend/resume */
+	unsigned long saved_rate;
+	unsigned long saved_parent_rate;
 };
 
 static const struct of_device_id cs2000_of_match[] = {
@@ -286,6 +290,9 @@ static int __cs2000_set_rate(struct cs2000_priv *priv, int ch,
 	if (ret < 0)
 		return ret;
 
+	priv->saved_rate	= rate;
+	priv->saved_parent_rate	= parent_rate;
+
 	return 0;
 }
 
@@ -489,9 +496,24 @@ static int cs2000_probe(struct i2c_client *client,
 	return ret;
 }
 
+static int cs2000_resume(struct device *dev)
+{
+	struct cs2000_priv *priv = dev_get_drvdata(dev);
+	int ch = 0; /* it uses ch0 only at this point */
+
+	return __cs2000_set_rate(priv, ch,
+				 priv->saved_rate,
+				 priv->saved_parent_rate);
+}
+
+static const struct dev_pm_ops cs2000_pm_ops = {
+	.resume_early	= cs2000_resume,
+};
+
 static struct i2c_driver cs2000_driver = {
 	.driver = {
 		.name = "cs2000-cp",
+		.pm	= &cs2000_pm_ops,
 		.of_match_table = cs2000_of_match,
 	},
 	.probe		= cs2000_probe,

drivers/clk/clk-scpi.c

@@ -290,13 +290,15 @@ static int scpi_clocks_probe(struct platform_device *pdev)
 			of_node_put(child);
 			return ret;
 		}
-	}
-	/* Add the virtual cpufreq device */
-	cpufreq_dev = platform_device_register_simple("scpi-cpufreq",
-						      -1, NULL, 0);
-	if (IS_ERR(cpufreq_dev))
-		pr_warn("unable to register cpufreq device");
 
+		if (match->data != &scpi_dvfs_ops)
+			continue;
+		/* Add the virtual cpufreq device if it's DVFS clock provider */
+		cpufreq_dev = platform_device_register_simple("scpi-cpufreq",
+							      -1, NULL, 0);
+		if (IS_ERR(cpufreq_dev))
+			pr_warn("unable to register cpufreq device");
+	}
 	return 0;
 }
 

drivers/clk/clk-wm831x.c

@@ -97,7 +97,8 @@ static int wm831x_fll_prepare(struct clk_hw *hw)
 	if (ret != 0)
 		dev_crit(wm831x->dev, "Failed to enable FLL: %d\n", ret);
 
-	usleep_range(2000, 2000);
+	/* wait 2-3 ms for new frequency taking effect */
+	usleep_range(2000, 3000);
 
 	return ret;
 }

drivers/clk/hisilicon/Kconfig

@@ -14,6 +14,13 @@ config COMMON_CLK_HI3519
 	help
 	  Build the clock driver for hi3519.
 
+config COMMON_CLK_HI3660
+	bool "Hi3660 Clock Driver"
+	depends on ARCH_HISI || COMPILE_TEST
+	default ARCH_HISI
+	help
+	  Build the clock driver for hi3660.
+
 config COMMON_CLK_HI3798CV200
 	tristate "Hi3798CV200 Clock Driver"
 	depends on ARCH_HISI || COMPILE_TEST

drivers/clk/hisilicon/Makefile

@@ -9,6 +9,7 @@ obj-$(CONFIG_ARCH_HIP04)	+= clk-hip04.o
 obj-$(CONFIG_ARCH_HIX5HD2)	+= clk-hix5hd2.o
 obj-$(CONFIG_COMMON_CLK_HI3516CV300)	+= crg-hi3516cv300.o
 obj-$(CONFIG_COMMON_CLK_HI3519)	+= clk-hi3519.o
+obj-$(CONFIG_COMMON_CLK_HI3660) += clk-hi3660.o
 obj-$(CONFIG_COMMON_CLK_HI3798CV200)	+= crg-hi3798cv200.o
 obj-$(CONFIG_COMMON_CLK_HI6220)	+= clk-hi6220.o
 obj-$(CONFIG_RESET_HISI)	+= reset.o

drivers/clk/hisilicon/clkgate-separated.c

@@ -120,6 +120,7 @@ struct clk *hisi_register_clkgate_sep(struct device *dev, const char *name,
 	sclk->bit_idx = bit_idx;
 	sclk->flags = clk_gate_flags;
 	sclk->hw.init = &init;
+	sclk->lock = lock;
 
 	clk = clk_register(dev, &sclk->hw);
 	if (IS_ERR(clk))

drivers/clk/imx/clk-imx6q.c

@@ -592,15 +592,20 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 
 	imx6q_mmdc_ch1_mask_handshake(base);
 
-	/*
-	 * The LDB_DI0/1_SEL muxes are registered read-only due to a hardware
-	 * bug. Set the muxes to the requested values before registering the
-	 * ldb_di_sel clocks.
-	 */
-	init_ldb_clks(np, base);
+	if (clk_on_imx6qp()) {
+		clk[IMX6QDL_CLK_LDB_DI0_SEL]      = imx_clk_mux_flags("ldb_di0_sel", base + 0x2c, 9,  3, ldb_di_sels,      ARRAY_SIZE(ldb_di_sels), CLK_SET_RATE_PARENT);
+		clk[IMX6QDL_CLK_LDB_DI1_SEL]      = imx_clk_mux_flags("ldb_di1_sel", base + 0x2c, 12, 3, ldb_di_sels,      ARRAY_SIZE(ldb_di_sels), CLK_SET_RATE_PARENT);
+	} else {
+		/*
+		 * The LDB_DI0/1_SEL muxes are registered read-only due to a hardware
+		 * bug. Set the muxes to the requested values before registering the
+		 * ldb_di_sel clocks.
+		 */
+		init_ldb_clks(np, base);
 
-	clk[IMX6QDL_CLK_LDB_DI0_SEL]      = imx_clk_mux_ldb("ldb_di0_sel", base + 0x2c, 9,  3, ldb_di_sels,      ARRAY_SIZE(ldb_di_sels));
-	clk[IMX6QDL_CLK_LDB_DI1_SEL]      = imx_clk_mux_ldb("ldb_di1_sel", base + 0x2c, 12, 3, ldb_di_sels,      ARRAY_SIZE(ldb_di_sels));
+		clk[IMX6QDL_CLK_LDB_DI0_SEL]      = imx_clk_mux_ldb("ldb_di0_sel", base + 0x2c, 9,  3, ldb_di_sels,      ARRAY_SIZE(ldb_di_sels));
+		clk[IMX6QDL_CLK_LDB_DI1_SEL]      = imx_clk_mux_ldb("ldb_di1_sel", base + 0x2c, 12, 3, ldb_di_sels,      ARRAY_SIZE(ldb_di_sels));
+	}
 	clk[IMX6QDL_CLK_IPU1_DI0_PRE_SEL] = imx_clk_mux_flags("ipu1_di0_pre_sel", base + 0x34, 6,  3, ipu_di_pre_sels,   ARRAY_SIZE(ipu_di_pre_sels), CLK_SET_RATE_PARENT);
 	clk[IMX6QDL_CLK_IPU1_DI1_PRE_SEL] = imx_clk_mux_flags("ipu1_di1_pre_sel", base + 0x34, 15, 3, ipu_di_pre_sels,   ARRAY_SIZE(ipu_di_pre_sels), CLK_SET_RATE_PARENT);
 	clk[IMX6QDL_CLK_IPU2_DI0_PRE_SEL] = imx_clk_mux_flags("ipu2_di0_pre_sel", base + 0x38, 6,  3, ipu_di_pre_sels,   ARRAY_SIZE(ipu_di_pre_sels), CLK_SET_RATE_PARENT);

drivers/clk/imx/clk-imx7d.c

@@ -803,6 +803,7 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
 	clks[IMX7D_DRAM_PHYM_ROOT_CLK] = imx_clk_gate4("dram_phym_root_clk", "dram_phym_cg", base + 0x4130, 0);
 	clks[IMX7D_DRAM_PHYM_ALT_ROOT_CLK] = imx_clk_gate4("dram_phym_alt_root_clk", "dram_phym_alt_post_div", base + 0x4130, 0);
 	clks[IMX7D_DRAM_ALT_ROOT_CLK] = imx_clk_gate4("dram_alt_root_clk", "dram_alt_post_div", base + 0x4130, 0);
+	clks[IMX7D_OCOTP_CLK] = imx_clk_gate4("ocotp_clk", "ipg_root_clk", base + 0x4230, 0);
 	clks[IMX7D_USB_HSIC_ROOT_CLK] = imx_clk_gate4("usb_hsic_root_clk", "usb_hsic_post_div", base + 0x4420, 0);
 	clks[IMX7D_SDMA_CORE_CLK] = imx_clk_gate4("sdma_root_clk", "ahb_root_clk", base + 0x4480, 0);
 	clks[IMX7D_PCIE_CTRL_ROOT_CLK] = imx_clk_gate4("pcie_ctrl_root_clk", "pcie_ctrl_post_div", base + 0x4600, 0);

drivers/clk/imx/clk-pllv3.c

@@ -21,6 +21,9 @@
 #define PLL_NUM_OFFSET		0x10
 #define PLL_DENOM_OFFSET	0x20
 
+#define PLL_VF610_NUM_OFFSET	0x20
+#define PLL_VF610_DENOM_OFFSET	0x30
+
 #define BM_PLL_POWER		(0x1 << 12)
 #define BM_PLL_LOCK		(0x1 << 31)
 #define IMX7_ENET_PLL_POWER	(0x1 << 5)
@@ -300,6 +303,99 @@ static const struct clk_ops clk_pllv3_av_ops = {
 	.set_rate	= clk_pllv3_av_set_rate,
 };
 
+struct clk_pllv3_vf610_mf {
+	u32 mfi;	/* integer part, can be 20 or 22 */
+	u32 mfn;	/* numerator, 30-bit value */
+	u32 mfd;	/* denominator, 30-bit value, must be less than mfn */
+};
+
+static unsigned long clk_pllv3_vf610_mf_to_rate(unsigned long parent_rate,
+		struct clk_pllv3_vf610_mf mf)
+{
+	u64 temp64;
+
+	temp64 = parent_rate;
+	temp64 *= mf.mfn;
+	do_div(temp64, mf.mfd);
+
+	return (parent_rate * mf.mfi) + temp64;
+}
+
+static struct clk_pllv3_vf610_mf clk_pllv3_vf610_rate_to_mf(
+		unsigned long parent_rate, unsigned long rate)
+{
+	struct clk_pllv3_vf610_mf mf;
+	u64 temp64;
+
+	mf.mfi = (rate >= 22 * parent_rate) ? 22 : 20;
+	mf.mfd = 0x3fffffff;	/* use max supported value for best accuracy */
+
+	if (rate <= parent_rate * mf.mfi)
+		mf.mfn = 0;
+	else if (rate >= parent_rate * (mf.mfi + 1))
+		mf.mfn = mf.mfd - 1;
+	else {
+		/* rate = parent_rate * (mfi + mfn/mfd) */
+		temp64 = rate - parent_rate * mf.mfi;
+		temp64 *= mf.mfd;
+		do_div(temp64, parent_rate);
+		mf.mfn = temp64;
+	}
+
+	return mf;
+}
+
+static unsigned long clk_pllv3_vf610_recalc_rate(struct clk_hw *hw,
+					      unsigned long parent_rate)
+{
+	struct clk_pllv3 *pll = to_clk_pllv3(hw);
+	struct clk_pllv3_vf610_mf mf;
+
+	mf.mfn = readl_relaxed(pll->base + PLL_VF610_NUM_OFFSET);
+	mf.mfd = readl_relaxed(pll->base + PLL_VF610_DENOM_OFFSET);
+	mf.mfi = (readl_relaxed(pll->base) & pll->div_mask) ? 22 : 20;
+
+	return clk_pllv3_vf610_mf_to_rate(parent_rate, mf);
+}
+
+static long clk_pllv3_vf610_round_rate(struct clk_hw *hw, unsigned long rate,
+				    unsigned long *prate)
+{
+	struct clk_pllv3_vf610_mf mf = clk_pllv3_vf610_rate_to_mf(*prate, rate);
+
+	return clk_pllv3_vf610_mf_to_rate(*prate, mf);
+}
+
+static int clk_pllv3_vf610_set_rate(struct clk_hw *hw, unsigned long rate,
+		unsigned long parent_rate)
+{
+	struct clk_pllv3 *pll = to_clk_pllv3(hw);
+	struct clk_pllv3_vf610_mf mf =
+			clk_pllv3_vf610_rate_to_mf(parent_rate, rate);
+	u32 val;
+
+	val = readl_relaxed(pll->base);
+	if (mf.mfi == 20)
+		val &= ~pll->div_mask;	/* clear bit for mfi=20 */
+	else
+		val |= pll->div_mask;	/* set bit for mfi=22 */
+	writel_relaxed(val, pll->base);
+
+	writel_relaxed(mf.mfn, pll->base + PLL_VF610_NUM_OFFSET);
+	writel_relaxed(mf.mfd, pll->base + PLL_VF610_DENOM_OFFSET);
+
+	return clk_pllv3_wait_lock(pll);
+}
+
+static const struct clk_ops clk_pllv3_vf610_ops = {
+	.prepare	= clk_pllv3_prepare,
+	.unprepare	= clk_pllv3_unprepare,
+	.is_prepared	= clk_pllv3_is_prepared,
+	.recalc_rate	= clk_pllv3_vf610_recalc_rate,
+	.round_rate	= clk_pllv3_vf610_round_rate,
+	.set_rate	= clk_pllv3_vf610_set_rate,
+};
+
 static unsigned long clk_pllv3_enet_recalc_rate(struct clk_hw *hw,
 						unsigned long parent_rate)
 {
@@ -334,6 +430,9 @@ struct clk *imx_clk_pllv3(enum imx_pllv3_type type, const char *name,
 	case IMX_PLLV3_SYS:
 		ops = &clk_pllv3_sys_ops;
 		break;
+	case IMX_PLLV3_SYS_VF610:
+		ops = &clk_pllv3_vf610_ops;
+		break;
 	case IMX_PLLV3_USB_VF610:
 		pll->div_shift = 1;
 	case IMX_PLLV3_USB:

drivers/clk/imx/clk-vf610.c

@@ -219,8 +219,8 @@ static void __init vf610_clocks_init(struct device_node *ccm_node)
 	clk[VF610_CLK_PLL6_BYPASS_SRC] = imx_clk_mux("pll6_bypass_src", PLL6_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels));
 	clk[VF610_CLK_PLL7_BYPASS_SRC] = imx_clk_mux("pll7_bypass_src", PLL7_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels));
 
-	clk[VF610_CLK_PLL1] = imx_clk_pllv3(IMX_PLLV3_GENERIC, "pll1", "pll1_bypass_src", PLL1_CTRL, 0x1);
-	clk[VF610_CLK_PLL2] = imx_clk_pllv3(IMX_PLLV3_GENERIC, "pll2", "pll2_bypass_src", PLL2_CTRL, 0x1);
+	clk[VF610_CLK_PLL1] = imx_clk_pllv3(IMX_PLLV3_SYS_VF610, "pll1", "pll1_bypass_src", PLL1_CTRL, 0x1);
+	clk[VF610_CLK_PLL2] = imx_clk_pllv3(IMX_PLLV3_SYS_VF610, "pll2", "pll2_bypass_src", PLL2_CTRL, 0x1);
 	clk[VF610_CLK_PLL3] = imx_clk_pllv3(IMX_PLLV3_USB_VF610,     "pll3", "pll3_bypass_src", PLL3_CTRL, 0x2);
 	clk[VF610_CLK_PLL4] = imx_clk_pllv3(IMX_PLLV3_AV,      "pll4", "pll4_bypass_src", PLL4_CTRL, 0x7f);
 	clk[VF610_CLK_PLL5] = imx_clk_pllv3(IMX_PLLV3_ENET,    "pll5", "pll5_bypass_src", PLL5_CTRL, 0x3);

drivers/clk/imx/clk.h

@@ -34,6 +34,7 @@ enum imx_pllv3_type {
 	IMX_PLLV3_AV,
 	IMX_PLLV3_ENET,
 	IMX_PLLV3_ENET_IMX7,
+	IMX_PLLV3_SYS_VF610,
 };
 
 struct clk *imx_clk_pllv3(enum imx_pllv3_type type, const char *name,

drivers/clk/mediatek/Kconfig

@@ -8,52 +8,53 @@ config COMMON_CLK_MEDIATEK
 
 config COMMON_CLK_MT2701
 	bool "Clock driver for Mediatek MT2701"
+	depends on (ARCH_MEDIATEK && ARM) || COMPILE_TEST
 	select COMMON_CLK_MEDIATEK
-	default ARCH_MEDIATEK
+	default ARCH_MEDIATEK && ARM
 	---help---
 	  This driver supports Mediatek MT2701 basic clocks.
 
 config COMMON_CLK_MT2701_MMSYS
 	bool "Clock driver for Mediatek MT2701 mmsys"
-	select COMMON_CLK_MT2701
+	depends on COMMON_CLK_MT2701
 	---help---
 	  This driver supports Mediatek MT2701 mmsys clocks.
 
 config COMMON_CLK_MT2701_IMGSYS
 	bool "Clock driver for Mediatek MT2701 imgsys"
-	select COMMON_CLK_MT2701
+	depends on COMMON_CLK_MT2701
 	---help---
 	  This driver supports Mediatek MT2701 imgsys clocks.
 
 config COMMON_CLK_MT2701_VDECSYS
 	bool "Clock driver for Mediatek MT2701 vdecsys"
-	select COMMON_CLK_MT2701
+	depends on COMMON_CLK_MT2701
 	---help---
 	  This driver supports Mediatek MT2701 vdecsys clocks.
 
 config COMMON_CLK_MT2701_HIFSYS
 	bool "Clock driver for Mediatek MT2701 hifsys"
-	select COMMON_CLK_MT2701
+	depends on COMMON_CLK_MT2701
 	---help---
 	  This driver supports Mediatek MT2701 hifsys clocks.
 
 config COMMON_CLK_MT2701_ETHSYS
 	bool "Clock driver for Mediatek MT2701 ethsys"
-	select COMMON_CLK_MT2701
+	depends on COMMON_CLK_MT2701
 	---help---
 	  This driver supports Mediatek MT2701 ethsys clocks.
 
 config COMMON_CLK_MT2701_BDPSYS
 	bool "Clock driver for Mediatek MT2701 bdpsys"
-	select COMMON_CLK_MT2701
+	depends on COMMON_CLK_MT2701
 	---help---
 	  This driver supports Mediatek MT2701 bdpsys clocks.
 
 config COMMON_CLK_MT8135
 	bool "Clock driver for Mediatek MT8135"
-	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on (ARCH_MEDIATEK && ARM) || COMPILE_TEST
 	select COMMON_CLK_MEDIATEK
-	default ARCH_MEDIATEK
+	default ARCH_MEDIATEK && ARM
 	---help---
 	  This driver supports Mediatek MT8135 clocks.
 

drivers/clk/meson/meson8b.c

@@ -607,7 +607,6 @@ static int meson8b_clkc_probe(struct platform_device *pdev)
 	/* Populate the base address for the MPEG clks */
 	meson8b_mpeg_clk_sel.reg = clk_base + (u32)meson8b_mpeg_clk_sel.reg;
 	meson8b_mpeg_clk_div.reg = clk_base + (u32)meson8b_mpeg_clk_div.reg;
-	meson8b_clk81.reg = clk_base + (u32)meson8b_clk81.reg;
 
 	/* Populate base address for gates */
 	for (i = 0; i < ARRAY_SIZE(meson8b_clk_gates); i++)

drivers/clk/mvebu/Makefile

@@ -9,7 +9,7 @@ obj-$(CONFIG_ARMADA_39X_CLK)	+= armada-39x.o
 obj-$(CONFIG_ARMADA_37XX_CLK)	+= armada-37xx-xtal.o
 obj-$(CONFIG_ARMADA_37XX_CLK)	+= armada-37xx-tbg.o
 obj-$(CONFIG_ARMADA_37XX_CLK)	+= armada-37xx-periph.o
-obj-$(CONFIG_ARMADA_XP_CLK)	+= armada-xp.o
+obj-$(CONFIG_ARMADA_XP_CLK)	+= armada-xp.o mv98dx3236.o
 obj-$(CONFIG_ARMADA_AP806_SYSCON) += ap806-system-controller.o
 obj-$(CONFIG_ARMADA_CP110_SYSCON) += cp110-system-controller.o
 obj-$(CONFIG_DOVE_CLK)		+= dove.o dove-divider.o

drivers/clk/mvebu/ap806-system-controller.c

@@ -55,21 +55,39 @@ static int ap806_syscon_clk_probe(struct platform_device *pdev)
 
 	freq_mode = reg & AP806_SAR_CLKFREQ_MODE_MASK;
 	switch (freq_mode) {
-	case 0x0 ... 0x5:
+	case 0x0:
+	case 0x1:
 		cpuclk_freq = 2000;
 		break;
-	case 0x6 ... 0xB:
+	case 0x6:
+	case 0x7:
 		cpuclk_freq = 1800;
 		break;
-	case 0xC ... 0x11:
+	case 0x4:
+	case 0xB:
+	case 0xD:
 		cpuclk_freq = 1600;
 		break;
-	case 0x12 ... 0x16:
+	case 0x1a:
 		cpuclk_freq = 1400;
 		break;
-	case 0x17 ... 0x19:
+	case 0x14:
+	case 0x17:
 		cpuclk_freq = 1300;
 		break;
+	case 0x19:
+		cpuclk_freq = 1200;
+		break;
+	case 0x13:
+	case 0x1d:
+		cpuclk_freq = 1000;
+		break;
+	case 0x1c:
+		cpuclk_freq = 800;
+		break;
+	case 0x1b:
+		cpuclk_freq = 600;
+		break;
 	default:
 		dev_err(&pdev->dev, "invalid SAR value\n");
 		return -EINVAL;

drivers/clk/mvebu/armada-xp.c

@@ -52,6 +52,12 @@ static u32 __init axp_get_tclk_freq(void __iomem *sar)
 	return 250000000;
 }
 
+/* MV98DX3236 TCLK frequency is fixed to 200MHz */
+static u32 __init mv98dx3236_get_tclk_freq(void __iomem *sar)
+{
+	return 200000000;
+}
+
 static const u32 axp_cpu_freqs[] __initconst = {
 	1000000000,
 	1066000000,
@@ -89,6 +95,12 @@ static u32 __init axp_get_cpu_freq(void __iomem *sar)
 	return cpu_freq;
 }
 
+/* MV98DX3236 CLK frequency is fixed to 800MHz */
+static u32 __init mv98dx3236_get_cpu_freq(void __iomem *sar)
+{
+	return 800000000;
+}
+
 static const int axp_nbclk_ratios[32][2] __initconst = {
 	{0, 1}, {1, 2}, {2, 2}, {2, 2},
 	{1, 2}, {1, 2}, {1, 1}, {2, 3},
@@ -158,6 +170,11 @@ static const struct coreclk_soc_desc axp_coreclks = {
 	.num_ratios = ARRAY_SIZE(axp_coreclk_ratios),
 };
 
+static const struct coreclk_soc_desc mv98dx3236_coreclks = {
+	.get_tclk_freq = mv98dx3236_get_tclk_freq,
+	.get_cpu_freq = mv98dx3236_get_cpu_freq,
+};
+
 /*
  * Clock Gating Control
  */
@@ -195,6 +212,15 @@ static const struct clk_gating_soc_desc axp_gating_desc[] __initconst = {
 	{ }
 };
 
+static const struct clk_gating_soc_desc mv98dx3236_gating_desc[] __initconst = {
+	{ "ge1", NULL, 3, 0 },
+	{ "ge0", NULL, 4, 0 },
+	{ "pex00", NULL, 5, 0 },
+	{ "sdio", NULL, 17, 0 },
+	{ "xor0", NULL, 22, 0 },
+	{ }
+};
+
 static void __init axp_clk_init(struct device_node *np)
 {
 	struct device_node *cgnp =

drivers/clk/mvebu/clk-cpu.c

@@ -245,3 +245,11 @@ static void __init of_cpu_clk_setup(struct device_node *node)
 
 CLK_OF_DECLARE(armada_xp_cpu_clock, "marvell,armada-xp-cpu-clock",
 					 of_cpu_clk_setup);
+
+static void __init of_mv98dx3236_cpu_clk_setup(struct device_node *node)
+{
+	of_clk_add_provider(node, of_clk_src_simple_get, NULL);
+}
+
+CLK_OF_DECLARE(mv98dx3236_cpu_clock, "marvell,mv98dx3236-cpu-clock",
+					 of_mv98dx3236_cpu_clk_setup);