mmc: dw_mmc: remove UBSAN warning in dw_mci_setup_bus()

This patch removes following UBSAN warnings in dw_mci_setup_bus().

  UBSAN: Undefined behaviour in drivers/mmc/host/dw_mmc.c:1102:14
  shift exponent 250 is too large for 32-bit type 'unsigned int'
  Call trace:
  [<ffffff90080908a8>] dump_backtrace+0x0/0x380
  [<ffffff9008090c3c>] show_stack+0x14/0x20
  [<ffffff90087457b8>] dump_stack+0xe0/0x120
  [<ffffff90087b1360>] ubsan_epilogue+0x18/0x68
  [<ffffff90087b1a94>] __ubsan_handle_shift_out_of_bounds+0x18c/0x1bc
  [<ffffff9008d89cb8>] dw_mci_setup_bus+0x3a0/0x438
  [...]

  UBSAN: Undefined behaviour in drivers/mmc/host/dw_mmc.c:1132:27
  shift exponent 250 is too large for 32-bit type 'unsigned int'
  Call trace:
  [<ffffff90080908a8>] dump_backtrace+0x0/0x380
  [<ffffff9008090c3c>] show_stack+0x14/0x20
  [<ffffff90087457b8>] dump_stack+0xe0/0x120
  [<ffffff90087b1360>] ubsan_epilogue+0x18/0x68
  [<ffffff90087b1a94>] __ubsan_handle_shift_out_of_bounds+0x18c/0x1bc
  [<ffffff9008d89c9c>] dw_mci_setup_bus+0x384/0x438
  [...]

The warnings are caused because of bit shift which is used to
filter spamming message for CONFIG_MMC_CLKGATE, but the config is
already removed. So this patch just removes the shift.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

drivers/mmc/host/dw_mmc.c

@@ -1100,12 +1100,11 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
 
 		div = (host->bus_hz != clock) ? DIV_ROUND_UP(div, 2) : 0;
 
-		if ((clock << div) != slot->__clk_old || force_clkinit)
-			dev_info(&slot->mmc->class_dev,
-				 "Bus speed (slot %d) = %dHz (slot req %dHz, actual %dHZ div = %d)\n",
-				 slot->id, host->bus_hz, clock,
-				 div ? ((host->bus_hz / div) >> 1) :
-				 host->bus_hz, div);
+		dev_info(&slot->mmc->class_dev,
+			 "Bus speed (slot %d) = %dHz (slot req %dHz, actual %dHZ div = %d)\n",
+			 slot->id, host->bus_hz, clock,
+			 div ? ((host->bus_hz / div) >> 1) :
+			 host->bus_hz, div);
 
 		/* disable clock */
 		mci_writel(host, CLKENA, 0);
@@ -1128,9 +1127,6 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
 
 		/* inform CIU */
 		mci_send_cmd(slot, sdmmc_cmd_bits, 0);
-
-		/* keep the clock with reflecting clock dividor */
-		slot->__clk_old = clock << div;
 	}
 
 	host->current_speed = clock;

drivers/mmc/host/dw_mmc.h

@@ -245,9 +245,6 @@ extern int dw_mci_resume(struct dw_mci *host);
  * @queue_node: List node for placing this node in the @queue list of
  *	&struct dw_mci.
  * @clock: Clock rate configured by set_ios(). Protected by host->lock.
- * @__clk_old: The last updated clock with reflecting clock divider.
- *	Keeping track of this helps us to avoid spamming the console
- *	with CONFIG_MMC_CLKGATE.
  * @flags: Random state bits associated with the slot.
  * @id: Number of this slot.
  * @sdio_id: Number of this slot in the SDIO interrupt registers.
@@ -262,7 +259,6 @@ struct dw_mci_slot {
 	struct list_head	queue_node;
 
 	unsigned int		clock;
-	unsigned int		__clk_old;
 
 	unsigned long		flags;
 #define DW_MMC_CARD_PRESENT	0