ARM: dts: qcom: Remove size elements from pmic reg properties

The #size-cells for the pmics are 0, but we specify a size in the
reg property so that MPP and GPIO modules can figure out how many
pins there are. Now that we've done that by counting irqs, we can
remove the size elements in the reg properties and be DT
compliant.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

arch/arm/boot/dts/qcom-pm8841.dtsi

@@ -11,7 +11,7 @@ pm8841_0: pm8841@4 {
 
 		pm8841_mpps: mpps@a000 {
 			compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp";
-			reg = <0xa000 0x400>;
+			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupts = <4 0xa0 0 IRQ_TYPE_NONE>,
@@ -22,7 +22,7 @@ pm8841_mpps: mpps@a000 {
 
 		temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
-			reg = <0x2400 0x100>;
+			reg = <0x2400>;
 			interrupts = <4 0x24 0 IRQ_TYPE_EDGE_RISING>;
 		};
 	};

arch/arm/boot/dts/qcom-pm8941.dtsi

@@ -12,15 +12,15 @@ pm8941_0: pm8941@0 {
 
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
-			reg = <0x6000 0x100>,
-			      <0x6100 0x100>;
+			reg = <0x6000>,
+			      <0x6100>;
 			reg-names = "rtc", "alarm";
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
 		pwrkey@800 {
 			compatible = "qcom,pm8941-pwrkey";
-			reg = <0x800 0x100>;
+			reg = <0x800>;
 			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 			debounce = <15625>;
 			bias-pull-up;
@@ -28,7 +28,7 @@ pwrkey@800 {
 
 		charger@1000 {
 			compatible = "qcom,pm8941-charger";
-			reg = <0x1000 0x700>;
+			reg = <0x1000>;
 			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
 				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
 				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
@@ -49,7 +49,7 @@ charger@1000 {
 
 		pm8941_gpios: gpios@c000 {
 			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
-			reg = <0xc000 0x2400>;
+			reg = <0xc000>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
@@ -92,7 +92,7 @@ pm8941_gpios: gpios@c000 {
 
 		pm8941_mpps: mpps@a000 {
 			compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
-			reg = <0xa000 0x800>;
+			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
@@ -107,7 +107,7 @@ pm8941_mpps: mpps@a000 {
 
 		pm8941_temp: temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
-			reg = <0x2400 0x100>;
+			reg = <0x2400>;
 			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
 			io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
 			io-channel-names = "thermal";
@@ -116,7 +116,7 @@ pm8941_temp: temp-alarm@2400 {
 
 		pm8941_vadc: vadc@3100 {
 			compatible = "qcom,spmi-vadc";
-			reg = <0x3100 0x100>;
+			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -141,7 +141,7 @@ ref_vdd {
 
 		pm8941_iadc: iadc@3600 {
 			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
-			reg = <0x3600 0x100>;
+			reg = <0x3600>;
 			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
 			qcom,external-resistor-micro-ohms = <10000>;
 		};
@@ -161,7 +161,7 @@ pm8941_1: pm8941@1 {
 
 		pm8941_wled: wled@d800 {
 			compatible = "qcom,pm8941-wled";
-			reg = <0xd800 0x100>;
+			reg = <0xd800>;
 			label = "backlight";
 
 			status = "disabled";