Commit 6a19309d authored by Julia Lawall's avatar Julia Lawall Committed by David S. Miller

drivers/atm: Use DIV_ROUND_UP

The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.

In the case of the file drivers/atm/eni.c, I am a little bit suspicious of
the -1 at the end of the affected expression.  Please check that that is
what is wanted.

An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression n,d;
@@

(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: default avatarJulia Lawall <julia@diku.dk>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent ca330c5a
......@@ -1270,7 +1270,7 @@ static int comp_tx(struct eni_dev *eni_dev,int *pcr,int reserved,int *pre,
if (*pre < 3) (*pre)++; /* else fail later */
div = pre_div[*pre]*-*pcr;
DPRINTK("max div %d\n",div);
*res = (TS_CLOCK+div-1)/div-1;
*res = DIV_ROUND_UP(TS_CLOCK, div)-1;
}
if (*res < 0) *res = 0;
if (*res > MID_SEG_MAX_RATE) *res = MID_SEG_MAX_RATE;
......
......@@ -635,7 +635,7 @@ static int make_rate (const hrz_dev * dev, u32 c, rounding r,
// take care of rounding
switch (r) {
case round_down:
pre = (br+(c<<div)-1)/(c<<div);
pre = DIV_ROUND_UP(br, c<<div);
// but p must be non-zero
if (!pre)
pre = 1;
......@@ -668,7 +668,7 @@ static int make_rate (const hrz_dev * dev, u32 c, rounding r,
// take care of rounding
switch (r) {
case round_down:
pre = (br+(c<<div)-1)/(c<<div);
pre = DIV_ROUND_UP(br, c<<div);
break;
case round_nearest:
pre = (br+(c<<div)/2)/(c<<div);
......@@ -698,7 +698,7 @@ static int make_rate (const hrz_dev * dev, u32 c, rounding r,
if (bits)
*bits = (div<<CLOCK_SELECT_SHIFT) | (pre-1);
if (actual) {
*actual = (br + (pre<<div) - 1) / (pre<<div);
*actual = DIV_ROUND_UP(br, pre<<div);
PRINTD (DBG_QOS, "actual rate: %u", *actual);
}
return 0;
......@@ -1967,7 +1967,7 @@ static int __devinit hrz_init (hrz_dev * dev) {
// Set the max AAL5 cell count to be just enough to contain the
// largest AAL5 frame that the user wants to receive
wr_regw (dev, MAX_AAL5_CELL_COUNT_OFF,
(max_rx_size + ATM_AAL5_TRAILER + ATM_CELL_PAYLOAD - 1) / ATM_CELL_PAYLOAD);
DIV_ROUND_UP(max_rx_size + ATM_AAL5_TRAILER, ATM_CELL_PAYLOAD));
// Enable receive
wr_regw (dev, RX_CONFIG_OFF, rd_regw (dev, RX_CONFIG_OFF) | RX_ENABLE);
......
......@@ -496,8 +496,8 @@ static int open_rx_first(struct atm_vcc *vcc)
vcc->qos.rxtp.max_sdu = 65464;
/* fix this - we may want to receive 64kB SDUs
later */
cells = (vcc->qos.rxtp.max_sdu+ATM_AAL5_TRAILER+
ATM_CELL_PAYLOAD-1)/ATM_CELL_PAYLOAD;
cells = DIV_ROUND_UP(vcc->qos.rxtp.max_sdu + ATM_AAL5_TRAILER,
ATM_CELL_PAYLOAD);
zatm_vcc->pool = pool_index(cells*ATM_CELL_PAYLOAD);
}
else {
......@@ -820,7 +820,7 @@ static int alloc_shaper(struct atm_dev *dev,int *pcr,int min,int max,int ubr)
}
else {
i = 255;
m = (ATM_OC3_PCR*255+max-1)/max;
m = DIV_ROUND_UP(ATM_OC3_PCR*255, max);
}
}
if (i > m) {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment