Merge branch 'net-phy-marvell-usb-to-mdio-controller'

Tobias Waldekranz says:

====================
net: phy: marvell usb to mdio controller

Support for an MDIO controller present on development boards for
Marvell switches from the Link Street (88E6xxx) family.

v3->v4:
- Remove unnecessary dependency on OF_MDIO.

v2->v3:
- Rename driver smi2usb -> mvusb.
- Clean up unused USB references.

v1->v2:
- Reverse christmas tree ordering of local variables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/marvell,mvusb.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/marvell,mvusb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell USB to MDIO Controller
+
+maintainers:
+  - Tobias Waldekranz <tobias@waldekranz.com>
+
+description: |+
+  This controller is mounted on development boards for Marvell's Link Street
+  family of Ethernet switches. It allows you to configure the switch's registers
+  using the standard MDIO interface.
+
+  Since the device is connected over USB, there is no strict requirement of
+  having a device tree representation of the device. But in order to use it with
+  the mv88e6xxx driver, you need a device tree node in which to place the switch
+  definition.
+
+allOf:
+  - $ref: "mdio.yaml#"
+
+properties:
+  compatible:
+    const: usb1286,1fa4
+  reg:
+    maxItems: 1
+    description: The USB port number on the host controller
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+
+examples:
+  - |
+    /* USB host controller */
+    &usb1 {
+            mvusb: mdio@1 {
+                    compatible = "usb1286,1fa4";
+                    reg = <1>;
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+            };
+    };
+
+    /* MV88E6390X devboard */
+    &mvusb {
+            switch@0 {
+                    compatible = "marvell,mv88e6190";
+                    status = "ok";
+                    reg = <0x0>;
+
+                    ports {
+                            /* Port definitions */
+                    };
+
+                    mdio {
+                            /* PHY definitions */
+                    };
+            };
+    };

MAINTAINERS

@@ -10106,6 +10106,13 @@ M:	Nicolas Pitre <nico@fluxnic.net>
 S:	Odd Fixes
 F:	drivers/mmc/host/mvsdio.*
 
+MARVELL USB MDIO CONTROLLER DRIVER
+M:	Tobias Waldekranz <tobias@waldekranz.com>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	drivers/net/phy/mdio-mvusb.c
+F:	Documentation/devicetree/bindings/net/marvell,mvusb.yaml
+
 MARVELL XENON MMC/SD/SDIO HOST CONTROLLER DRIVER
 M:	Hu Ziji <huziji@marvell.com>
 L:	linux-mmc@vger.kernel.org

drivers/net/phy/Kconfig

@@ -179,6 +179,13 @@ config MDIO_MSCC_MIIM
 	  This driver supports the MIIM (MDIO) interface found in the network
 	  switches of the Microsemi SoCs
 
+config MDIO_MVUSB
+	tristate "Marvell USB to MDIO Adapter"
+	depends on USB
+	help
+	  A USB to MDIO converter present on development boards for
+	  Marvell's Link Street family of Ethernet switches.
+
 config MDIO_OCTEON
 	tristate "Octeon and some ThunderX SOCs MDIO buses"
 	depends on (64BIT && OF_MDIO) || COMPILE_TEST

drivers/net/phy/Makefile

@@ -40,6 +40,7 @@ obj-$(CONFIG_MDIO_I2C)		+= mdio-i2c.o
 obj-$(CONFIG_MDIO_IPQ8064)	+= mdio-ipq8064.o
 obj-$(CONFIG_MDIO_MOXART)	+= mdio-moxart.o
 obj-$(CONFIG_MDIO_MSCC_MIIM)	+= mdio-mscc-miim.o
+obj-$(CONFIG_MDIO_MVUSB)	+= mdio-mvusb.o
 obj-$(CONFIG_MDIO_OCTEON)	+= mdio-octeon.o
 obj-$(CONFIG_MDIO_SUN4I)	+= mdio-sun4i.o
 obj-$(CONFIG_MDIO_THUNDER)	+= mdio-thunder.o

drivers/net/phy/mdio-mvusb.c

+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_mdio.h>
+#include <linux/phy.h>
+#include <linux/usb.h>
+
+#define USB_MARVELL_VID	0x1286
+
+static const struct usb_device_id mvusb_mdio_table[] = {
+	{ USB_DEVICE(USB_MARVELL_VID, 0x1fa4) },
+
+	{}
+};
+MODULE_DEVICE_TABLE(usb, mvusb_mdio_table);
+
+enum {
+	MVUSB_CMD_PREAMBLE0,
+	MVUSB_CMD_PREAMBLE1,
+	MVUSB_CMD_ADDR,
+	MVUSB_CMD_VAL,
+};
+
+struct mvusb_mdio {
+	struct usb_device *udev;
+	struct mii_bus *mdio;
+
+	__le16 buf[4];
+};
+
+static int mvusb_mdio_read(struct mii_bus *mdio, int dev, int reg)
+{
+	struct mvusb_mdio *mvusb = mdio->priv;
+	int err, alen;
+
+	if (dev & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
+	mvusb->buf[MVUSB_CMD_ADDR] = cpu_to_le16(0xa400 | (dev << 5) | reg);
+
+	err = usb_bulk_msg(mvusb->udev, usb_sndbulkpipe(mvusb->udev, 2),
+			   mvusb->buf, 6, &alen, 100);
+	if (err)
+		return err;
+
+	err = usb_bulk_msg(mvusb->udev, usb_rcvbulkpipe(mvusb->udev, 6),
+			   &mvusb->buf[MVUSB_CMD_VAL], 2, &alen, 100);
+	if (err)
+		return err;
+
+	return le16_to_cpu(mvusb->buf[MVUSB_CMD_VAL]);
+}
+
+static int mvusb_mdio_write(struct mii_bus *mdio, int dev, int reg, u16 val)
+{
+	struct mvusb_mdio *mvusb = mdio->priv;
+	int alen;
+
+	if (dev & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
+	mvusb->buf[MVUSB_CMD_ADDR] = cpu_to_le16(0x8000 | (dev << 5) | reg);
+	mvusb->buf[MVUSB_CMD_VAL]  = cpu_to_le16(val);
+
+	return usb_bulk_msg(mvusb->udev, usb_sndbulkpipe(mvusb->udev, 2),
+			    mvusb->buf, 8, &alen, 100);
+}
+
+static int mvusb_mdio_probe(struct usb_interface *interface,
+			    const struct usb_device_id *id)
+{
+	struct device *dev = &interface->dev;
+	struct mvusb_mdio *mvusb;
+	struct mii_bus *mdio;
+
+	mdio = devm_mdiobus_alloc_size(dev, sizeof(*mvusb));
+	if (!mdio)
+		return -ENOMEM;
+
+	mvusb = mdio->priv;
+	mvusb->mdio = mdio;
+	mvusb->udev = usb_get_dev(interface_to_usbdev(interface));
+
+	/* Reversed from USB PCAPs, no idea what these mean. */
+	mvusb->buf[MVUSB_CMD_PREAMBLE0] = cpu_to_le16(0xe800);
+	mvusb->buf[MVUSB_CMD_PREAMBLE1] = cpu_to_le16(0x0001);
+
+	snprintf(mdio->id, MII_BUS_ID_SIZE, "mvusb-%s", dev_name(dev));
+	mdio->name = mdio->id;
+	mdio->parent = dev;
+	mdio->read = mvusb_mdio_read;
+	mdio->write = mvusb_mdio_write;
+
+	usb_set_intfdata(interface, mvusb);
+	return of_mdiobus_register(mdio, dev->of_node);
+}
+
+static void mvusb_mdio_disconnect(struct usb_interface *interface)
+{
+	struct mvusb_mdio *mvusb = usb_get_intfdata(interface);
+	struct usb_device *udev = mvusb->udev;
+
+	mdiobus_unregister(mvusb->mdio);
+	usb_set_intfdata(interface, NULL);
+	usb_put_dev(udev);
+}
+
+static struct usb_driver mvusb_mdio_driver = {
+	.name       = "mvusb_mdio",
+	.id_table   = mvusb_mdio_table,
+	.probe      = mvusb_mdio_probe,
+	.disconnect = mvusb_mdio_disconnect,
+};
+
+module_usb_driver(mvusb_mdio_driver);
+
+MODULE_AUTHOR("Tobias Waldekranz <tobias@waldekranz.com>");
+MODULE_DESCRIPTION("Marvell USB MDIO Adapter");
+MODULE_LICENSE("GPL");