Commit 6ccc7435 authored by Dan Murphy's avatar Dan Murphy Committed by Jacek Anaszewski

dt: lm3532: Add lm3532 dt doc and update ti_lmu doc

Add the lm3532 device tree documentation.
Remove lm3532 device tree reference from the ti_lmu devicetree
documentation.

With the addition of the dedicated lm3532 documentation the device
can be removed from the ti_lmu.txt.

The reason for this is that the lm3532 dt documentation now defines
the ability to control LED output strings against different control
banks or groups multiple strings to be controlled by a single control
bank.

Another addition was for ALS lighting control and configuration.  The
LM3532 has a feature that can take in the ALS reading from 2 separate
ALS devices and adjust the brightness on the strings that are configured
to support this feature.

Finally the device specific properties were moved to the parent node
as these properties are not control bank configurable.  These include
the runtime ramp and the ALS configuration.
Signed-off-by: default avatarDan Murphy <dmurphy@ti.com>
Reviewed-by: default avatarRob Herring <robh@kernel.org>
Acked-for-MFD-by: default avatarLee Jones <lee.jones@linaro.org>
Acked-by: default avatarTony Lindgren <tony@atomide.com>
Signed-off-by: default avatarJacek Anaszewski <jacek.anaszewski@gmail.com>
parent 9e98c678
* Texas Instruments - lm3532 White LED driver with ambient light sensing
capability.
The LM3532 provides the 3 high-voltage, low-side current sinks. The device is
programmable over an I2C-compatible interface and has independent
current control for all three channels. The adaptive current regulation
method allows for different LED currents in each current sink thus allowing
for a wide variety of backlight and keypad applications.
The main features of the LM3532 include dual ambient light sensor inputs
each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
brightness control, dual external PWM brightness control inputs, and up to
1000:1 dimming ratio with programmable fade in and fade out settings.
Required properties:
- compatible : "ti,lm3532"
- reg : I2C slave address
- #address-cells : 1
- #size-cells : 0
Optional properties:
- enable-gpios : gpio pin to enable (active high)/disable the device.
- ramp-up-us - The Run time ramp rates/step are from one current
set-point to another after the device has reached its
initial target set point from turn-on
- ramp-down-us - The Run time ramp rates/step are from one current
set-point to another after the device has reached its
initial target set point from turn-on
Range for ramp settings: 8us - 65536us
Optional properties if ALS mode is used:
- ti,als-vmin - Minimum ALS voltage defined in Volts
- ti,als-vmax - Maximum ALS voltage defined in Volts
Per the data sheet the max ALS voltage is 2V and the min is 0V
- ti,als1-imp-sel - ALS1 impedance resistor selection in Ohms
- ti,als2-imp-sel - ALS2 impedance resistor selection in Ohms
Range for impedance select: 37000 Ohms - 1190 Ohms
Values above 37kohms will be set to the "High Impedance" setting
- ti,als-avrg-time-us - Determines the length of time the device needs to
average the two ALS inputs. This is only used if
the input mode is LM3532_ALS_INPUT_AVRG.
Range: 17920us - 2293760us
- ti,als-input-mode - Determines how the device uses the attached ALS
devices.
0x00 - ALS1 and ALS2 input average
0x01 - ALS1 Input
0x02 - ALS2 Input
0x03 - Max of ALS1 and ALS2
Required child properties:
- reg : Indicates control bank the LED string is controlled by
- led-sources : see Documentation/devicetree/bindings/leds/common.txt
- ti,led-mode : Defines if the LED strings are manually controlled or
if the LED strings are controlled by the ALS.
0x00 - LED strings are I2C controlled via full scale
brightness control register
0x01 - LED strings are ALS controlled
Optional LED child properties:
- label : see Documentation/devicetree/bindings/leds/common.txt
- linux,default-trigger :
see Documentation/devicetree/bindings/leds/common.txt
Example:
led-controller@38 {
compatible = "ti,lm3532";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x38>;
enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
ramp-up-us = <1024>;
ramp-down-us = <65536>;
ti,als-vmin = <0>;
ti,als-vmax = <2000>;
ti,als1-imp-sel = <4110>;
ti,als2-imp-sel = <2180>;
ti,als-avrg-time-us = <17920>;
ti,als-input-mode = <0x00>;
led@0 {
reg = <0>;
led-sources = <2>;
ti,led-mode = <1>;
label = ":backlight";
linux,default-trigger = "backlight";
};
led@1 {
reg = <1>;
led-sources = <1>;
ti,led-mode = <0>;
label = ":kbd_backlight";
};
};
For more product information please see the links below:
http://www.ti.com/product/LM3532
......@@ -4,7 +4,6 @@ TI LMU driver supports lighting devices below.
Name Child nodes
------ ---------------------------------
LM3532 Backlight
LM3631 Backlight and regulator
LM3632 Backlight and regulator
LM3633 Backlight, LED and fault monitor
......@@ -13,7 +12,6 @@ TI LMU driver supports lighting devices below.
Required properties:
- compatible: Should be one of:
"ti,lm3532"
"ti,lm3631"
"ti,lm3632"
"ti,lm3633"
......@@ -23,7 +21,6 @@ Required properties:
0x11 for LM3632
0x29 for LM3631
0x36 for LM3633, LM3697
0x38 for LM3532
0x63 for LM3695
Optional property:
......@@ -47,23 +44,6 @@ Optional nodes:
[2] ../leds/leds-lm3633.txt
[3] ../regulator/lm363x-regulator.txt
lm3532@38 {
compatible = "ti,lm3532";
reg = <0x38>;
enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
backlight {
compatible = "ti,lm3532-backlight";
lcd {
led-sources = <0 1 2>;
ramp-up-msec = <30>;
ramp-down-msec = <0>;
};
};
};
lm3631@29 {
compatible = "ti,lm3631";
reg = <0x29>;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment