Commit 6d6ce40f authored by Tony Lindgren's avatar Tony Lindgren Committed by Kishon Vijay Abraham I

phy: cpcap-usb: Add CPCAP PMIC USB support

Some Motorola phones like droid 4 use a custom CPCAP PMIC that has a
multiplexing USB PHY.

This USB PHY can operate at least in four modes using pin multiplexing
and two control GPIOS:

- Pass through companion PHY for the SoC USB PHY
- ULPI PHY for the SoC
- Pass through USB for the modem
- UART debug console for the SoC

This patch adds support for droid 4 USB PHY and debug UART modes,
support for other modes can be added later on as needed.

Both peripheral and host mode are working for the USB. The
host mode depends on the cpcap-charger driver for VBUS.

VBUS and ID pin detection are done using cpcap-adc IIO ADC
driver.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Acked-by: default avatarRob Herring <robh@kernel.org>
Tested-by: default avatarSebastian Reichel <sre@kernel.org>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
Signed-off-by: default avatarKishon Vijay Abraham I <kishon@ti.com>
parent 4a3449d1
Motorola CPCAP PMIC USB PHY binding
Required properties:
compatible: Shall be either "motorola,cpcap-usb-phy" or
"motorola,mapphone-cpcap-usb-phy"
#phy-cells: Shall be 0
interrupts: CPCAP PMIC interrupts used by the USB PHY
interrupt-names: Interrupt names
io-channels: IIO ADC channels used by the USB PHY
io-channel-names: IIO ADC channel names
vusb-supply: Regulator for the PHY
Optional properties:
pinctrl: Optional alternate pin modes for the PHY
pinctrl-names: Names for optional pin modes
mode-gpios: Optional GPIOs for configuring alternate modes
Example:
cpcap_usb2_phy: phy {
compatible = "motorola,mapphone-cpcap-usb-phy";
pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>;
pinctrl-1 = <&usb_ulpi_pins>;
pinctrl-2 = <&usb_utmi_pins>;
pinctrl-3 = <&uart3_pins>;
pinctrl-names = "default", "ulpi", "utmi", "uart";
#phy-cells = <0>;
interrupts-extended = <
&cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0
&cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0
&cpcap 48 1
>;
interrupt-names =
"id_ground", "id_float", "se0conn", "vbusvld",
"sessvld", "sessend", "se1", "dm", "dp";
mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH
&gpio1 0 GPIO_ACTIVE_HIGH>;
io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>;
io-channel-names = "vbus", "id";
vusb-supply = <&vusb>;
};
...@@ -53,6 +53,7 @@ source "drivers/phy/amlogic/Kconfig" ...@@ -53,6 +53,7 @@ source "drivers/phy/amlogic/Kconfig"
source "drivers/phy/broadcom/Kconfig" source "drivers/phy/broadcom/Kconfig"
source "drivers/phy/hisilicon/Kconfig" source "drivers/phy/hisilicon/Kconfig"
source "drivers/phy/marvell/Kconfig" source "drivers/phy/marvell/Kconfig"
source "drivers/phy/motorola/Kconfig"
source "drivers/phy/qualcomm/Kconfig" source "drivers/phy/qualcomm/Kconfig"
source "drivers/phy/renesas/Kconfig" source "drivers/phy/renesas/Kconfig"
source "drivers/phy/rockchip/Kconfig" source "drivers/phy/rockchip/Kconfig"
......
...@@ -16,6 +16,7 @@ obj-$(CONFIG_ARCH_TEGRA) += tegra/ ...@@ -16,6 +16,7 @@ obj-$(CONFIG_ARCH_TEGRA) += tegra/
obj-y += broadcom/ \ obj-y += broadcom/ \
hisilicon/ \ hisilicon/ \
marvell/ \ marvell/ \
motorola/ \
qualcomm/ \ qualcomm/ \
samsung/ \ samsung/ \
st/ \ st/ \
......
#
# Phy drivers for Motorola devices
#
config PHY_CPCAP_USB
tristate "CPCAP PMIC USB PHY driver"
depends on USB_SUPPORT && IIO
select GENERIC_PHY
select USB_PHY
help
Enable this for USB to work on Motorola phones and tablets
such as Droid 4.
#
# Makefile for the phy drivers.
#
obj-$(CONFIG_PHY_CPCAP_USB) += phy-cpcap-usb.o
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment