Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (coretemp) Fix checkpatch errors
  hwmon: Remove pkgtemp driver
  hwmon: (coretemp) Merge pkgtemp with coretemp
  hwmon: (pmbus) Add support for Analog Devices ADM1275
  hwmon: (pmbus) Support for TI UCD90xxx series Sequencer and System Health Controllers
  hwmon: (pmbus) Add support for TI UCD9200 series of PWM System Controllers
  hwmon: (pmbus) Use device specific function to read fan configuration
  hwmon: (pmbus) Expand scope of device specific get_status function
  hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers
  hwmon: Driver for MAX16065 System Manager and compatibles
  hwmon: (sht15) add support for CRC validation
  hwmon: (sht15) add support for the status register
  hwmon: (sht15) clean-up the probe function
  hwmon: (sht15) general code clean-up
  hwmon: Add support for MAX6642

Documentation/hwmon/adm1275

+Kernel driver adm1275
+=====================
+
+Supported chips:
+  * Analog Devices ADM1275
+    Prefix: 'adm1275'
+    Addresses scanned: -
+    Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1275.pdf
+
+Author: Guenter Roeck <guenter.roeck@ericsson.com>
+
+
+Description
+-----------
+
+This driver supports hardware montoring for Analog Devices ADM1275 Hot-Swap
+Controller and Digital Power Monitor.
+
+The ADM1275 is a hot-swap controller that allows a circuit board to be removed
+from or inserted into a live backplane. It also features current and voltage
+readback via an integrated 12-bit analog-to-digital converter (ADC), accessed
+using a PMBus. interface.
+
+The driver is a client driver to the core PMBus driver. Please see
+Documentation/hwmon/pmbus for details on PMBus client drivers.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Platform data support
+---------------------
+
+The driver supports standard PMBus driver platform data. Please see
+Documentation/hwmon/pmbus for details.
+
+
+Sysfs entries
+-------------
+
+The following attributes are supported. Limits are read-write; all other
+attributes are read-only.
+
+in1_label		"vin1" or "vout1" depending on chip variant and
+			configuration.
+in1_input		Measured voltage. From READ_VOUT register.
+in1_min			Minumum Voltage. From VOUT_UV_WARN_LIMIT register.
+in1_max			Maximum voltage. From VOUT_OV_WARN_LIMIT register.
+in1_min_alarm		Voltage low alarm. From VOLTAGE_UV_WARNING status.
+in1_max_alarm		Voltage high alarm. From VOLTAGE_OV_WARNING status.
+
+curr1_label		"iout1"
+curr1_input		Measured current. From READ_IOUT register.
+curr1_max		Maximum current. From IOUT_OC_WARN_LIMIT register.
+curr1_max_alarm		Current high alarm. From IOUT_OC_WARN_LIMIT register.

Documentation/hwmon/coretemp

@@ -15,8 +15,13 @@ Author: Rudolf Marek
 
 Description
 -----------
+This driver permits reading the DTS (Digital Temperature Sensor) embedded
+inside Intel CPUs. This driver can read both the per-core and per-package
+temperature using the appropriate sensors. The per-package sensor is new;
+as of now, it is present only in the SandyBridge platform. The driver will
+show the temperature of all cores inside a package under a single device
+directory inside hwmon.
 
-This driver permits reading temperature sensor embedded inside Intel Core CPU.
 Temperature is measured in degrees Celsius and measurement resolution is
 1 degree C. Valid temperatures are from 0 to TjMax degrees C, because
 the actual value of temperature register is in fact a delta from TjMax.
@@ -27,13 +32,15 @@ mechanism will perform actions to forcibly cool down the processor. Alarm
 may be raised, if the temperature grows enough (more than TjMax) to trigger
 the Out-Of-Spec bit. Following table summarizes the exported sysfs files:
 
-temp1_input	 - Core temperature (in millidegrees Celsius).
-temp1_max	 - All cooling devices should be turned on (on Core2).
-temp1_crit	 - Maximum junction temperature (in millidegrees Celsius).
-temp1_crit_alarm - Set when Out-of-spec bit is set, never clears.
+All Sysfs entries are named with their core_id (represented here by 'X').
+tempX_input	 - Core temperature (in millidegrees Celsius).
+tempX_max	 - All cooling devices should be turned on (on Core2).
+tempX_crit	 - Maximum junction temperature (in millidegrees Celsius).
+tempX_crit_alarm - Set when Out-of-spec bit is set, never clears.
 		   Correct CPU operation is no longer guaranteed.
-temp1_label	 - Contains string "Core X", where X is processor
-		   number.
+tempX_label	 - Contains string "Core X", where X is processor
+		   number. For Package temp, this will be "Physical id Y",
+		   where Y is the package number.
 
 The TjMax temperature is set to 85 degrees C if undocumented model specific
 register (UMSR) 0xee has bit 30 set. If not the TjMax is 100 degrees C as

Documentation/hwmon/max16065

+Kernel driver max16065
+======================
+
+Supported chips:
+  * Maxim MAX16065, MAX16066
+    Prefixes: 'max16065', 'max16066'
+    Addresses scanned: -
+    Datasheet:
+	http://datasheets.maxim-ic.com/en/ds/MAX16065-MAX16066.pdf
+ *  Maxim MAX16067
+    Prefix: 'max16067'
+    Addresses scanned: -
+    Datasheet:
+	http://datasheets.maxim-ic.com/en/ds/MAX16067.pdf
+ *  Maxim MAX16068
+    Prefix: 'max16068'
+    Addresses scanned: -
+    Datasheet:
+	http://datasheets.maxim-ic.com/en/ds/MAX16068.pdf
+ *  Maxim MAX16070/MAX16071
+    Prefixes: 'max16070', 'max16071'
+    Addresses scanned: -
+    Datasheet:
+	http://datasheets.maxim-ic.com/en/ds/MAX16070-MAX16071.pdf
+
+
+Author: Guenter Roeck <guenter.roeck@ericsson.com>
+
+
+Description
+-----------
+
+[From datasheets] The MAX16065/MAX16066 flash-configurable system managers
+monitor and sequence multiple system voltages. The MAX16065/MAX16066 can also
+accurately monitor (+/-2.5%) one current channel using a dedicated high-side
+current-sense amplifier. The MAX16065 manages up to twelve system voltages
+simultaneously, and the MAX16066 manages up to eight supply voltages.
+
+The MAX16067 flash-configurable system manager monitors and sequences multiple
+system voltages. The MAX16067 manages up to six system voltages simultaneously.
+
+The MAX16068 flash-configurable system manager monitors and manages up to six
+system voltages simultaneously.
+
+The MAX16070/MAX16071 flash-configurable system monitors supervise multiple
+system voltages. The MAX16070/MAX16071 can also accurately monitor (+/-2.5%)
+one current channel using a dedicated high-side current-sense amplifier. The
+MAX16070 monitors up to twelve system voltages simultaneously, and the MAX16071
+monitors up to eight supply voltages.
+
+Each monitored channel has its own low and high critical limits. MAX16065,
+MAX16066, MAX16070, and MAX16071 support an additional limit which is
+configurable as either low or high secondary limit. MAX16065, MAX16066,
+MAX16070, and MAX16071 also support supply current monitoring.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for devices, since there is no register which
+can be safely used to identify the chip. You will have to instantiate
+the devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Sysfs entries
+-------------
+
+in[0-11]_input		Input voltage measurements.
+
+in12_input		Voltage on CSP (Current Sense Positive) pin.
+			Only if the chip supports current sensing and if
+			current sensing is enabled.
+
+in[0-11]_min		Low warning limit.
+			Supported on MAX16065, MAX16066, MAX16070, and MAX16071
+			only.
+
+in[0-11]_max		High warning limit.
+			Supported on MAX16065, MAX16066, MAX16070, and MAX16071
+			only.
+
+			Either low or high warning limits are supported
+			(depending on chip configuration), but not both.
+
+in[0-11]_lcrit		Low critical limit.
+
+in[0-11]_crit		High critical limit.
+
+in[0-11]_alarm		Input voltage alarm.
+
+curr1_input		Current sense input; only if the chip supports current
+			sensing and if current sensing is enabled.
+			Displayed current assumes 0.001 Ohm current sense
+			resistor.
+
+curr1_alarm		Overcurrent alarm; only if the chip supports current
+			sensing and if current sensing is enabled.

Documentation/hwmon/max6642

+Kernel driver max6642
+=====================
+
+Supported chips:
+  * Maxim MAX6642
+    Prefix: 'max6642'
+    Addresses scanned: I2C 0x48-0x4f
+    Datasheet: Publicly available at the Maxim website
+               http://datasheets.maxim-ic.com/en/ds/MAX6642.pdf
+
+Authors:
+        Per Dalen <per.dalen@appeartv.com>
+
+Description
+-----------
+
+The MAX6642 is a digital temperature sensor. It senses its own temperature as
+well as the temperature on one external diode.
+
+All temperature values are given in degrees Celsius. Resolution
+is 0.25 degree for the local temperature and for the remote temperature.

Documentation/hwmon/pkgtemp

-Kernel driver pkgtemp
-======================
-
-Supported chips:
-  * Intel family
-    Prefix: 'pkgtemp'
-    CPUID:
-    Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual
-               Volume 3A: System Programming Guide
-
-Author: Fenghua Yu
-
-Description
------------
-
-This driver permits reading package level temperature sensor embedded inside
-Intel CPU package. The sensors can be in core, uncore, memory controller, or
-other components in a package. The feature is first implemented in Intel Sandy
-Bridge platform.
-
-Temperature is measured in degrees Celsius and measurement resolution is
-1 degree C. Valid temperatures are from 0 to TjMax degrees C, because the actual
-value of temperature register is in fact a delta from TjMax.
-
-Temperature known as TjMax is the maximum junction temperature of package.
-We get this from MSR_IA32_TEMPERATURE_TARGET. If the MSR is not accessible,
-we define TjMax as 100 degrees Celsius. At this temperature, protection
-mechanism will perform actions to forcibly cool down the package. Alarm
-may be raised, if the temperature grows enough (more than TjMax) to trigger
-the Out-Of-Spec bit. Following table summarizes the exported sysfs files:
-
-temp1_input	  - Package temperature (in millidegrees Celsius).
-temp1_max        - All cooling devices should be turned on.
-temp1_crit	  - Maximum junction temperature (in millidegrees Celsius).
-temp1_crit_alarm - Set when Out-of-spec bit is set, never clears.
-		    Correct CPU operation is no longer guaranteed.

Documentation/hwmon/sht15

+Kernel driver sht15
+===================
+
+Authors:
+  * Wouter Horre
+  * Jonathan Cameron
+  * Vivien Didelot <vivien.didelot@savoirfairelinux.com>
+  * Jerome Oufella <jerome.oufella@savoirfairelinux.com>
+
+Supported chips:
+  * Sensirion SHT10
+    Prefix: 'sht10'
+
+  * Sensirion SHT11
+    Prefix: 'sht11'
+
+  * Sensirion SHT15
+    Prefix: 'sht15'
+
+  * Sensirion SHT71
+    Prefix: 'sht71'
+
+  * Sensirion SHT75
+    Prefix: 'sht75'
+
+Datasheet: Publicly available at the Sensirion website
+http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf
+
+Description
+-----------
+
+The SHT10, SHT11, SHT15, SHT71, and SHT75 are humidity and temperature
+sensors.
+
+The devices communicate using two GPIO lines.
+
+Supported resolutions for the measurements are 14 bits for temperature and 12
+bits for humidity, or 12 bits for temperature and 8 bits for humidity.
+
+The humidity calibration coefficients are programmed into an OTP memory on the
+chip. These coefficients are used to internally calibrate the signals from the
+sensors. Disabling the reload of those coefficients allows saving 10ms for each
+measurement and decrease power consumption, while loosing on precision.
+
+Some options may be set directly in the sht15_platform_data structure
+or via sysfs attributes.
+
+Notes:
+  * The regulator supply name is set to "vcc".
+  * If a CRC validation fails, a soft reset command is sent, which resets
+    status register to its hardware default value, but the driver will try to
+    restore the previous device configuration.
+
+Platform data
+-------------
+
+* checksum:
+  set it to true to enable CRC validation of the readings (default to false).
+* no_otp_reload:
+  flag to indicate not to reload from OTP (default to false).
+* low_resolution:
+  flag to indicate the temp/humidity resolution to use (default to false).
+
+Sysfs interface
+---------------
+
+* temp1_input:     temperature input
+* humidity1_input: humidity input
+* heater_enable:   write 1 in this attribute to enable the on-chip heater,
+                   0 to disable it. Be careful not to enable the heater
+                   for too long.
+* temp1_fault:     if 1, this means that the voltage is low (below 2.47V) and
+                   measurement may be invalid.
+* humidity1_fault: same as temp1_fault.

Documentation/hwmon/ucd9000

+Kernel driver ucd9000
+=====================
+
+Supported chips:
+  * TI UCD90120, UCD90124, UCD9090, and UCD90910
+    Prefixes: 'ucd90120', 'ucd90124', 'ucd9090', 'ucd90910'
+    Addresses scanned: -
+    Datasheets:
+	http://focus.ti.com/lit/ds/symlink/ucd90120.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd90124.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd9090.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd90910.pdf
+
+Author: Guenter Roeck <guenter.roeck@ericsson.com>
+
+
+Description
+-----------
+
+From datasheets:
+
+The UCD90120 Power Supply Sequencer and System Health Monitor monitors and
+sequences up to 12 independent voltage rails. The device integrates a 12-bit
+ADC with a 2.5V internal reference for monitoring up to 13 power supply voltage,
+current, or temperature inputs.
+
+The UCD90124 is a 12-rail PMBus/I2C addressable power-supply sequencer and
+system-health monitor. The device integrates a 12-bit ADC for monitoring up to
+13 power-supply voltage, current, or temperature inputs. Twenty-six GPIO pins
+can be used for power supply enables, power-on reset signals, external
+interrupts, cascading, or other system functions. Twelve of these pins offer PWM
+functionality. Using these pins, the UCD90124 offers support for fan control,
+margining, and general-purpose PWM functions.
+
+The UCD9090 is a 10-rail PMBus/I2C addressable power-supply sequencer and
+monitor. The device integrates a 12-bit ADC for monitoring up to 10 power-supply
+voltage inputs. Twenty-three GPIO pins can be used for power supply enables,
+power-on reset signals, external interrupts, cascading, or other system
+functions. Ten of these pins offer PWM functionality. Using these pins, the
+UCD9090 offers support for margining, and general-purpose PWM functions.
+
+The UCD90910 is a ten-rail I2C / PMBus addressable power-supply sequencer and
+system-health monitor. The device integrates a 12-bit ADC for monitoring up to
+13 power-supply voltage, current, or temperature inputs.
+
+This driver is a client driver to the core PMBus driver. Please see
+Documentation/hwmon/pmbus for details on PMBus client drivers.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Platform data support
+---------------------
+
+The driver supports standard PMBus driver platform data. Please see
+Documentation/hwmon/pmbus for details.
+
+
+Sysfs entries
+-------------
+
+The following attributes are supported. Limits are read-write; all other
+attributes are read-only.
+
+in[1-12]_label		"vout[1-12]".
+in[1-12]_input		Measured voltage. From READ_VOUT register.
+in[1-12]_min		Minumum Voltage. From VOUT_UV_WARN_LIMIT register.
+in[1-12]_max		Maximum voltage. From VOUT_OV_WARN_LIMIT register.
+in[1-12]_lcrit		Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register.
+in[1-12]_crit		Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register.
+in[1-12]_min_alarm	Voltage low alarm. From VOLTAGE_UV_WARNING status.
+in[1-12]_max_alarm	Voltage high alarm. From VOLTAGE_OV_WARNING status.
+in[1-12]_lcrit_alarm	Voltage critical low alarm. From VOLTAGE_UV_FAULT status.
+in[1-12]_crit_alarm	Voltage critical high alarm. From VOLTAGE_OV_FAULT status.
+
+curr[1-12]_label	"iout[1-12]".
+curr[1-12]_input	Measured current. From READ_IOUT register.
+curr[1-12]_max		Maximum current. From IOUT_OC_WARN_LIMIT register.
+curr[1-12]_lcrit	Critical minumum output current. From IOUT_UC_FAULT_LIMIT
+			register.
+curr[1-12]_crit		Critical maximum current. From IOUT_OC_FAULT_LIMIT register.
+curr[1-12]_max_alarm	Current high alarm. From IOUT_OC_WARNING status.
+curr[1-12]_crit_alarm	Current critical high alarm. From IOUT_OC_FAULT status.
+
+			For each attribute index, either voltage or current is
+			reported, but not both. If voltage or current is
+			reported depends on the chip configuration.
+
+temp[1-2]_input		Measured temperatures. From READ_TEMPERATURE_1 and
+			READ_TEMPERATURE_2 registers.
+temp[1-2]_max		Maximum temperature. From OT_WARN_LIMIT register.
+temp[1-2]_crit		Critical high temperature. From OT_FAULT_LIMIT register.
+temp[1-2]_max_alarm	Temperature high alarm.
+temp[1-2]_crit_alarm	Temperature critical high alarm.
+
+fan[1-4]_input		Fan RPM.
+fan[1-4]_alarm		Fan alarm.
+fan[1-4]_fault		Fan fault.
+
+			Fan attributes are only available on chips supporting
+			fan control (UCD90124, UCD90910). Attribute files are
+			created only for enabled fans.
+			Note that even though UCD90910 supports up to 10 fans,
+			only up to four fans are currently supported.

Documentation/hwmon/ucd9200

+Kernel driver ucd9200
+=====================
+
+Supported chips:
+  * TI UCD9220, UCD9222, UCD9224, UCD9240, UCD9244, UCD9246, and UCD9248
+    Prefixes: 'ucd9220', 'ucd9222', 'ucd9224', 'ucd9240', 'ucd9244', 'ucd9246',
+	'ucd9248'
+    Addresses scanned: -
+    Datasheets:
+	http://focus.ti.com/lit/ds/symlink/ucd9220.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd9222.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd9224.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd9240.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd9244.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd9246.pdf
+	http://focus.ti.com/lit/ds/symlink/ucd9248.pdf
+
+Author: Guenter Roeck <guenter.roeck@ericsson.com>
+
+
+Description
+-----------
+
+[From datasheets] UCD9220, UCD9222, UCD9224, UCD9240, UCD9244, UCD9246, and
+UCD9248 are multi-rail, multi-phase synchronous buck digital PWM controllers
+designed for non-isolated DC/DC power applications. The devices integrate
+dedicated circuitry for DC/DC loop management with flash memory and a serial
+interface to support configuration, monitoring and management.
+
+This driver is a client driver to the core PMBus driver. Please see
+Documentation/hwmon/pmbus for details on PMBus client drivers.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Platform data support
+---------------------
+
+The driver supports standard PMBus driver platform data. Please see
+Documentation/hwmon/pmbus for details.
+
+
+Sysfs entries
+-------------
+
+The following attributes are supported. Limits are read-write; all other
+attributes are read-only.
+
+in1_label		"vin".
+in1_input		Measured voltage. From READ_VIN register.
+in1_min			Minumum Voltage. From VIN_UV_WARN_LIMIT register.
+in1_max			Maximum voltage. From VIN_OV_WARN_LIMIT register.
+in1_lcrit		Critical minumum Voltage. VIN_UV_FAULT_LIMIT register.
+in1_crit		Critical maximum voltage. From VIN_OV_FAULT_LIMIT register.
+in1_min_alarm		Voltage low alarm. From VIN_UV_WARNING status.
+in1_max_alarm		Voltage high alarm. From VIN_OV_WARNING status.
+in1_lcrit_alarm		Voltage critical low alarm. From VIN_UV_FAULT status.
+in1_crit_alarm		Voltage critical high alarm. From VIN_OV_FAULT status.
+
+in[2-5]_label		"vout[1-4]".
+in[2-5]_input		Measured voltage. From READ_VOUT register.
+in[2-5]_min		Minumum Voltage. From VOUT_UV_WARN_LIMIT register.
+in[2-5]_max		Maximum voltage. From VOUT_OV_WARN_LIMIT register.
+in[2-5]_lcrit		Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register.
+in[2-5]_crit		Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register.
+in[2-5]_min_alarm	Voltage low alarm. From VOLTAGE_UV_WARNING status.
+in[2-5]_max_alarm	Voltage high alarm. From VOLTAGE_OV_WARNING status.
+in[2-5]_lcrit_alarm	Voltage critical low alarm. From VOLTAGE_UV_FAULT status.
+in[2-5]_crit_alarm	Voltage critical high alarm. From VOLTAGE_OV_FAULT status.
+
+curr1_label		"iin".
+curr1_input		Measured current. From READ_IIN register.
+
+curr[2-5]_label		"iout[1-4]".
+curr[2-5]_input		Measured current. From READ_IOUT register.
+curr[2-5]_max		Maximum current. From IOUT_OC_WARN_LIMIT register.
+curr[2-5]_lcrit		Critical minumum output current. From IOUT_UC_FAULT_LIMIT
+			register.
+curr[2-5]_crit		Critical maximum current. From IOUT_OC_FAULT_LIMIT register.
+curr[2-5]_max_alarm	Current high alarm. From IOUT_OC_WARNING status.
+curr[2-5]_crit_alarm	Current critical high alarm. From IOUT_OC_FAULT status.
+
+power1_input		Measured input power. From READ_PIN register.
+power1_label		"pin"
+
+power[2-5]_input	Measured output power. From READ_POUT register.
+power[2-5]_label	"pout[1-4]"
+
+			The number of output voltage, current, and power
+			attribute sets is determined by the number of enabled
+			rails. See chip datasheets for details.
+
+temp[1-5]_input		Measured temperatures. From READ_TEMPERATURE_1 and
+		        READ_TEMPERATURE_2 registers.
+			temp1 is the chip internal temperature. temp[2-5] are
+			rail temperatures.  temp[2-5] attributes are only
+			created for enabled rails. See chip datasheets for
+			details.
+temp[1-5]_max		Maximum temperature. From OT_WARN_LIMIT register.
+temp[1-5]_crit		Critical high temperature. From OT_FAULT_LIMIT register.
+temp[1-5]_max_alarm	Temperature high alarm.
+temp[1-5]_crit_alarm	Temperature critical high alarm.
+
+fan1_input		Fan RPM. ucd9240 only.
+fan1_alarm		Fan alarm. ucd9240 only.
+fan1_fault		Fan fault. ucd9240 only.

drivers/hwmon/Kconfig

@@ -408,13 +408,6 @@ config SENSORS_CORETEMP
 	  sensor inside your CPU. Most of the family 6 CPUs
 	  are supported. Check Documentation/hwmon/coretemp for details.
 
-config SENSORS_PKGTEMP
-	tristate "Intel processor package temperature sensor"
-	depends on X86 && EXPERIMENTAL
-	help
-	  If you say yes here you get support for the package level temperature
-	  sensor inside your CPU. Check documentation/driver for details.
-
 config SENSORS_IBMAEM
 	tristate "IBM Active Energy Manager temperature/power sensors and control"
 	select IPMI_SI
@@ -708,6 +701,22 @@ config SENSORS_MAX1111
 	  This driver can also be built as a module.  If so, the module
 	  will be called max1111.
 
+config SENSORS_MAX16065
+	tristate "Maxim MAX16065 System Manager and compatibles"
+	depends on I2C
+	help
+	  If you say yes here you get support for hardware monitoring
+	  capabilities of the following Maxim System Manager chips.
+	    MAX16065
+	    MAX16066
+	    MAX16067
+	    MAX16068
+	    MAX16070
+	    MAX16071
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called max16065.
+
 config SENSORS_MAX1619
 	tristate "Maxim MAX1619 sensor chip"
 	depends on I2C
@@ -727,6 +736,17 @@ config SENSORS_MAX6639
 	  This driver can also be built as a module.  If so, the module
 	  will be called max6639.
 
+config SENSORS_MAX6642
+	tristate "Maxim MAX6642 sensor chip"
+	depends on I2C && EXPERIMENTAL
+	help
+	  If you say yes here you get support for MAX6642 sensor chip.
+	  MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor
+	  with Overtemperature Alarm from Maxim.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called max6642.
+
 config SENSORS_MAX6650
 	tristate "Maxim MAX6650 sensor chip"
 	depends on I2C && EXPERIMENTAL
@@ -800,6 +820,16 @@ config SENSORS_PMBUS
 	  This driver can also be built as a module. If so, the module will
 	  be called pmbus.
 
+config SENSORS_ADM1275
+	tristate "Analog Devices ADM1275"
+	default n
+	help
+	  If you say yes here you get hardware monitoring support for Analog
+	  Devices ADM1275 Hot-Swap Controller and Digital Power Monitor.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called adm1275.
+
 config SENSORS_MAX16064
 	tristate "Maxim MAX16064"
 	default n
@@ -830,6 +860,28 @@ config SENSORS_MAX8688
 	  This driver can also be built as a module. If so, the module will
 	  be called max8688.
 
+config SENSORS_UCD9000
+	tristate "TI UCD90120, UCD90124, UCD9090, UCD90910"
+	default n
+	help
+	  If you say yes here you get hardware monitoring support for TI
+	  UCD90120, UCD90124, UCD9090, UCD90910 Sequencer and System Health
+	  Controllers.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called ucd9000.
+
+config SENSORS_UCD9200
+	tristate "TI UCD9220, UCD9222, UCD9224, UCD9240, UCD9244, UCD9246, UCD9248"
+	default n
+	help
+	  If you say yes here you get hardware monitoring support for TI
+	  UCD9220, UCD9222, UCD9224, UCD9240, UCD9244, UCD9246, and UCD9248
+	  Digital PWM System Controllers.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called ucd9200.
+
 endif # PMBUS
 
 config SENSORS_SHT15

drivers/hwmon/Makefile

@@ -40,7 +40,6 @@ obj-$(CONFIG_SENSORS_APPLESMC)	+= applesmc.o
 obj-$(CONFIG_SENSORS_ASC7621)	+= asc7621.o
 obj-$(CONFIG_SENSORS_ATXP1)	+= atxp1.o
 obj-$(CONFIG_SENSORS_CORETEMP)	+= coretemp.o
-obj-$(CONFIG_SENSORS_PKGTEMP)	+= pkgtemp.o
 obj-$(CONFIG_SENSORS_DME1737)	+= dme1737.o
 obj-$(CONFIG_SENSORS_DS620)	+= ds620.o
 obj-$(CONFIG_SENSORS_DS1621)	+= ds1621.o
@@ -83,8 +82,10 @@ obj-$(CONFIG_SENSORS_LTC4215)	+= ltc4215.o
 obj-$(CONFIG_SENSORS_LTC4245)	+= ltc4245.o
 obj-$(CONFIG_SENSORS_LTC4261)	+= ltc4261.o
 obj-$(CONFIG_SENSORS_MAX1111)	+= max1111.o
+obj-$(CONFIG_SENSORS_MAX16065)	+= max16065.o
 obj-$(CONFIG_SENSORS_MAX1619)	+= max1619.o
 obj-$(CONFIG_SENSORS_MAX6639)	+= max6639.o
+obj-$(CONFIG_SENSORS_MAX6642)	+= max6642.o
 obj-$(CONFIG_SENSORS_MAX6650)	+= max6650.o
 obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o
 obj-$(CONFIG_SENSORS_PC87360)	+= pc87360.o
@@ -118,9 +119,12 @@ obj-$(CONFIG_SENSORS_WM8350)	+= wm8350-hwmon.o
 # PMBus drivers
 obj-$(CONFIG_PMBUS)		+= pmbus_core.o
 obj-$(CONFIG_SENSORS_PMBUS)	+= pmbus.o
+obj-$(CONFIG_SENSORS_ADM1275)	+= adm1275.o
 obj-$(CONFIG_SENSORS_MAX16064)	+= max16064.o
 obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
+obj-$(CONFIG_SENSORS_UCD9000)	+= ucd9000.o
+obj-$(CONFIG_SENSORS_UCD9200)	+= ucd9200.o
 
 ccflags-$(CONFIG_HWMON_DEBUG_CHIP) := -DDEBUG
 

drivers/hwmon/adm1275.c

+/*
+ * Hardware monitoring driver for Analog Devices ADM1275 Hot-Swap Controller
+ * and Digital Power Monitor
+ *
+ * Copyright (c) 2011 Ericsson AB.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include "pmbus.h"
+
+#define ADM1275_PMON_CONFIG		0xd4
+
+#define ADM1275_VIN_VOUT_SELECT		(1 << 6)
+#define ADM1275_VRANGE			(1 << 5)
+
+static int adm1275_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	int config;
+	struct pmbus_driver_info *info;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_READ_BYTE_DATA))
+		return -ENODEV;
+
+	info = kzalloc(sizeof(struct pmbus_driver_info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	config = i2c_smbus_read_byte_data(client, ADM1275_PMON_CONFIG);
+	if (config < 0)
+		return config;
+
+	info->pages = 1;
+	info->direct[PSC_VOLTAGE_IN] = true;
+	info->direct[PSC_VOLTAGE_OUT] = true;
+	info->direct[PSC_CURRENT_OUT] = true;
+	info->m[PSC_CURRENT_OUT] = 800;
+	info->b[PSC_CURRENT_OUT] = 20475;
+	info->R[PSC_CURRENT_OUT] = -1;
+	info->func[0] = PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT;
+
+	if (config & ADM1275_VRANGE) {
+		info->m[PSC_VOLTAGE_IN] = 19045;
+		info->b[PSC_VOLTAGE_IN] = 0;
+		info->R[PSC_VOLTAGE_IN] = -2;
+		info->m[PSC_VOLTAGE_OUT] = 19045;
+		info->b[PSC_VOLTAGE_OUT] = 0;
+		info->R[PSC_VOLTAGE_OUT] = -2;
+	} else {
+		info->m[PSC_VOLTAGE_IN] = 6666;
+		info->b[PSC_VOLTAGE_IN] = 0;
+		info->R[PSC_VOLTAGE_IN] = -1;
+		info->m[PSC_VOLTAGE_OUT] = 6666;
+		info->b[PSC_VOLTAGE_OUT] = 0;
+		info->R[PSC_VOLTAGE_OUT] = -1;
+	}
+
+	if (config & ADM1275_VIN_VOUT_SELECT)
+		info->func[0] |= PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT;
+	else
+		info->func[0] |= PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT;
+
+	return pmbus_do_probe(client, id, info);
+}
+
+static int adm1275_remove(struct i2c_client *client)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	int ret;
+
+	ret = pmbus_do_remove(client);
+	kfree(info);
+	return ret;
+}
+
+static const struct i2c_device_id adm1275_id[] = {
+	{"adm1275", 0},
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, adm1275_id);
+
+static struct i2c_driver adm1275_driver = {
+	.driver = {
+		   .name = "adm1275",
+		   },
+	.probe = adm1275_probe,
+	.remove = adm1275_remove,
+	.id_table = adm1275_id,
+};
+
+static int __init adm1275_init(void)
+{
+	return i2c_add_driver(&adm1275_driver);
+}
+
+static void __exit adm1275_exit(void)
+{
+	i2c_del_driver(&adm1275_driver);
+}
+
+MODULE_AUTHOR("Guenter Roeck");
+MODULE_DESCRIPTION("PMBus driver for Analog Devices ADM1275");
+MODULE_LICENSE("GPL");
+module_init(adm1275_init);
+module_exit(adm1275_exit);

drivers/hwmon/max34440.c

@@ -32,7 +32,7 @@ enum chips { max34440, max34441 };
 #define MAX34440_STATUS_OT_FAULT	(1 << 5)
 #define MAX34440_STATUS_OT_WARN		(1 << 6)
 
-static int max34440_get_status(struct i2c_client *client, int page, int reg)
+static int max34440_read_byte_data(struct i2c_client *client, int page, int reg)
 {
 	int ret;
 	int mfg_status;
@@ -108,7 +108,7 @@ static struct pmbus_driver_info max34440_info[] = {
 		.func[11] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
 		.func[12] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
 		.func[13] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
-		.get_status = max34440_get_status,
+		.read_byte_data = max34440_read_byte_data,
 	},
 	[max34441] = {
 		.pages = 12,
@@ -149,7 +149,7 @@ static struct pmbus_driver_info max34440_info[] = {
 		.func[9] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
 		.func[10] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
 		.func[11] = PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
-		.get_status = max34440_get_status,
+		.read_byte_data = max34440_read_byte_data,
 	},
 };
 

drivers/hwmon/max6642.c

+/*
+ * Driver for +/-1 degree C, SMBus-Compatible Remote/Local Temperature Sensor
+ * with Overtemperature Alarm
+ *
+ * Copyright (C) 2011 AppearTV AS
+ *
+ * Derived from:
+ *
+ *  Based on the max1619 driver.
+ *  Copyright (C) 2003-2004 Alexey Fisher <fishor@mail.ru>
+ *                          Jean Delvare <khali@linux-fr.org>
+ *
+ * The MAX6642 is a sensor chip made by Maxim.
+ * It reports up to two temperatures (its own plus up to
+ * one external one). Complete datasheet can be
+ * obtained from Maxim's website at:
+ *   http://datasheets.maxim-ic.com/en/ds/MAX6642.pdf
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+
+static const unsigned short normal_i2c[] = {
+	0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
+
+/*
+ * The MAX6642 registers
+ */
+
+#define MAX6642_REG_R_MAN_ID		0xFE
+#define MAX6642_REG_R_CONFIG		0x03
+#define MAX6642_REG_W_CONFIG		0x09
+#define MAX6642_REG_R_STATUS		0x02
+#define MAX6642_REG_R_LOCAL_TEMP	0x00
+#define MAX6642_REG_R_LOCAL_TEMPL	0x11
+#define MAX6642_REG_R_LOCAL_HIGH	0x05
+#define MAX6642_REG_W_LOCAL_HIGH	0x0B
+#define MAX6642_REG_R_REMOTE_TEMP	0x01
+#define MAX6642_REG_R_REMOTE_TEMPL	0x10
+#define MAX6642_REG_R_REMOTE_HIGH	0x07
+#define MAX6642_REG_W_REMOTE_HIGH	0x0D
+
+/*
+ * Conversions
+ */
+
+static int temp_from_reg10(int val)
+{
+	return val * 250;
+}
+
+static int temp_from_reg(int val)
+{
+	return val * 1000;
+}
+
+static int temp_to_reg(int val)
+{
+	return val / 1000;
+}
+
+/*
+ * Client data (each client gets its own)
+ */
+
+struct max6642_data {
+	struct device *hwmon_dev;
+	struct mutex update_lock;
+	bool valid; /* zero until following fields are valid */
+	unsigned long last_updated; /* in jiffies */
+
+	/* registers values */
+	u16 temp_input[2]; /* local/remote */
+	u16 temp_high[2]; /* local/remote */
+	u8 alarms;
+};
+
+/*
+ * Real code
+ */
+
+static void max6642_init_client(struct i2c_client *client)
+{
+	u8 config;
+	struct max6642_data *data = i2c_get_clientdata(client);
+
+	/*
+	 * Start the conversions.
+	 */
+	config = i2c_smbus_read_byte_data(client, MAX6642_REG_R_CONFIG);
+	if (config & 0x40)
+		i2c_smbus_write_byte_data(client, MAX6642_REG_W_CONFIG,
+					  config & 0xBF); /* run */
+
+	data->temp_high[0] = i2c_smbus_read_byte_data(client,
+				MAX6642_REG_R_LOCAL_HIGH);
+	data->temp_high[1] = i2c_smbus_read_byte_data(client,
+				MAX6642_REG_R_REMOTE_HIGH);
+}
+
+/* Return 0 if detection is successful, -ENODEV otherwise */
+static int max6642_detect(struct i2c_client *client,
+			  struct i2c_board_info *info)
+{
+	struct i2c_adapter *adapter = client->adapter;
+	u8 reg_config, reg_status, man_id;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+		return -ENODEV;
+
+	/* identification */
+	man_id = i2c_smbus_read_byte_data(client, MAX6642_REG_R_MAN_ID);
+	if (man_id != 0x4D)
+		return -ENODEV;
+
+	/*
+	 * We read the config and status register, the 4 lower bits in the
+	 * config register should be zero and bit 5, 3, 1 and 0 should be
+	 * zero in the status register.
+	 */
+	reg_config = i2c_smbus_read_byte_data(client, MAX6642_REG_R_CONFIG);
+	reg_status = i2c_smbus_read_byte_data(client, MAX6642_REG_R_STATUS);
+	if (((reg_config & 0x0f) != 0x00) ||
+	    ((reg_status & 0x2b) != 0x00))
+		return -ENODEV;
+
+	strlcpy(info->type, "max6642", I2C_NAME_SIZE);
+
+	return 0;
+}
+
+static struct max6642_data *max6642_update_device(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct max6642_data *data = i2c_get_clientdata(client);
+	u16 val, tmp;
+
+	mutex_lock(&data->update_lock);
+
+	if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
+		dev_dbg(&client->dev, "Updating max6642 data.\n");
+		val = i2c_smbus_read_byte_data(client,
+					MAX6642_REG_R_LOCAL_TEMPL);
+		tmp = (val >> 6) & 3;
+		val = i2c_smbus_read_byte_data(client,
+					MAX6642_REG_R_LOCAL_TEMP);
+		val = (val << 2) | tmp;
+		data->temp_input[0] = val;
+		val = i2c_smbus_read_byte_data(client,
+					MAX6642_REG_R_REMOTE_TEMPL);
+		tmp = (val >> 6) & 3;
+		val = i2c_smbus_read_byte_data(client,
+					MAX6642_REG_R_REMOTE_TEMP);
+		val = (val << 2) | tmp;
+		data->temp_input[1] = val;
+		data->alarms = i2c_smbus_read_byte_data(client,
+					MAX6642_REG_R_STATUS);
+
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+
+	mutex_unlock(&data->update_lock);
+
+	return data;
+}
+
+/*
+ * Sysfs stuff
+ */
+
+static ssize_t show_temp_max10(struct device *dev,
+			       struct device_attribute *dev_attr, char *buf)
+{
+	struct max6642_data *data = max6642_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
+
+	return sprintf(buf, "%d\n",
+		       temp_from_reg10(data->temp_input[attr->index]));
+}
+
+static ssize_t show_temp_max(struct device *dev, struct device_attribute *attr,
+			     char *buf)
+{
+	struct max6642_data *data = max6642_update_device(dev);
+	struct sensor_device_attribute_2 *attr2 = to_sensor_dev_attr_2(attr);
+
+	return sprintf(buf, "%d\n", temp_from_reg(data->temp_high[attr2->nr]));
+}
+
+static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr,
+			    const char *buf, size_t count)
+{
+	unsigned long val;
+	int err;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct max6642_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2 *attr2 = to_sensor_dev_attr_2(attr);
+
+	err = strict_strtoul(buf, 10, &val);
+	if (err < 0)
+		return err;
+
+	mutex_lock(&data->update_lock);
+	data->temp_high[attr2->nr] = SENSORS_LIMIT(temp_to_reg(val), 0, 255);
+	i2c_smbus_write_byte_data(client, attr2->index,
+				  data->temp_high[attr2->nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
+			  char *buf)
+{
+	int bitnr = to_sensor_dev_attr(attr)->index;
+	struct max6642_data *data = max6642_update_device(dev);
+	return sprintf(buf, "%d\n", (data->alarms >> bitnr) & 1);
+}
+
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_max10, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp_max10, NULL, 1);
+static SENSOR_DEVICE_ATTR_2(temp1_max, S_IWUSR | S_IRUGO, show_temp_max,
+			    set_temp_max, 0, MAX6642_REG_W_LOCAL_HIGH);
+static SENSOR_DEVICE_ATTR_2(temp2_max, S_IWUSR | S_IRUGO, show_temp_max,
+			    set_temp_max, 1, MAX6642_REG_W_REMOTE_HIGH);
+static SENSOR_DEVICE_ATTR(temp_fault, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 6);
+static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 4);
+
+static struct attribute *max6642_attributes[] = {
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp2_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_max.dev_attr.attr,
+	&sensor_dev_attr_temp2_max.dev_attr.attr,
+
+	&sensor_dev_attr_temp_fault.dev_attr.attr,
+	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
+	&sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group max6642_group = {
+	.attrs = max6642_attributes,
+};
+
+static int max6642_probe(struct i2c_client *new_client,
+			 const struct i2c_device_id *id)
+{
+	struct max6642_data *data;
+	int err;
+
+	data = kzalloc(sizeof(struct max6642_data), GFP_KERNEL);
+	if (!data) {
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	i2c_set_clientdata(new_client, data);
+	mutex_init(&data->update_lock);
+
+	/* Initialize the MAX6642 chip */
+	max6642_init_client(new_client);
+
+	/* Register sysfs hooks */
+	err = sysfs_create_group(&new_client->dev.kobj, &max6642_group);
+	if (err)
+		goto exit_free;
+
+	data->hwmon_dev = hwmon_device_register(&new_client->dev);
+	if (IS_ERR(data->hwmon_dev)) {
+		err = PTR_ERR(data->hwmon_dev);
+		goto exit_remove_files;
+	}
+
+	return 0;
+
+exit_remove_files:
+	sysfs_remove_group(&new_client->dev.kobj, &max6642_group);
+exit_free:
+	kfree(data);
+exit:
+	return err;
+}
+
+static int max6642_remove(struct i2c_client *client)
+{
+	struct max6642_data *data = i2c_get_clientdata(client);
+
+	hwmon_device_unregister(data->hwmon_dev);
+	sysfs_remove_group(&client->dev.kobj, &max6642_group);
+
+	kfree(data);
+	return 0;
+}
+
+/*
+ * Driver data (common to all clients)
+ */
+
+static const struct i2c_device_id max6642_id[] = {
+	{ "max6642", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, max6642_id);
+
+static struct i2c_driver max6642_driver = {
+	.class		= I2C_CLASS_HWMON,
+	.driver = {
+		.name	= "max6642",
+	},
+	.probe		= max6642_probe,
+	.remove		= max6642_remove,
+	.id_table	= max6642_id,
+	.detect		= max6642_detect,
+	.address_list	= normal_i2c,
+};
+
+static int __init max6642_init(void)
+{
+	return i2c_add_driver(&max6642_driver);
+}
+
+static void __exit max6642_exit(void)
+{
+	i2c_del_driver(&max6642_driver);
+}
+
+MODULE_AUTHOR("Per Dalen <per.dalen@appeartv.com>");
+MODULE_DESCRIPTION("MAX6642 sensor driver");
+MODULE_LICENSE("GPL");
+
+module_init(max6642_init);
+module_exit(max6642_exit);

drivers/hwmon/max8688.c

@@ -37,7 +37,7 @@
 #define MAX8688_STATUS_OT_FAULT		(1 << 13)
 #define MAX8688_STATUS_OT_WARNING	(1 << 14)
 
-static int max8688_get_status(struct i2c_client *client, int page, int reg)
+static int max8688_read_byte_data(struct i2c_client *client, int page, int reg)
 {
 	int ret = 0;
 	int mfg_status;
@@ -110,7 +110,7 @@ static struct pmbus_driver_info max8688_info = {
 	.func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_IOUT | PMBUS_HAVE_TEMP
 		| PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_STATUS_IOUT
 		| PMBUS_HAVE_STATUS_TEMP,
-	.get_status = max8688_get_status,
+	.read_byte_data = max8688_read_byte_data,
 };
 
 static int max8688_probe(struct i2c_client *client,

drivers/hwmon/pmbus.h

@@ -281,13 +281,11 @@ struct pmbus_driver_info {
 
 	u32 func[PMBUS_PAGES];	/* Functionality, per page */
 	/*
-	 * The get_status function maps manufacturing specific status values
-	 * into PMBus standard status values.
-	 * This function is optional and only necessary if chip specific status
-	 * register values have to be mapped into standard PMBus status register
-	 * values.
+	 * The following functions map manufacturing specific register values
+	 * to PMBus standard register values. Specify only if mapping is
+	 * necessary.
 	 */
-	int (*get_status)(struct i2c_client *client, int page, int reg);
+	int (*read_byte_data)(struct i2c_client *client, int page, int reg);
 	/*
 	 * The identify function determines supported PMBus functionality.
 	 * This function is only necessary if a chip driver supports multiple

drivers/hwmon/ucd9000.c

+/*
+ * Hardware monitoring driver for UCD90xxx Sequencer and System Health
+ * Controller series
+ *
+ * Copyright (C) 2011 Ericsson AB.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/i2c/pmbus.h>
+#include "pmbus.h"
+
+enum chips { ucd9000, ucd90120, ucd90124, ucd9090, ucd90910 };
+
+#define UCD9000_MONITOR_CONFIG		0xd5
+#define UCD9000_NUM_PAGES		0xd6
+#define UCD9000_FAN_CONFIG_INDEX	0xe7
+#define UCD9000_FAN_CONFIG		0xe8
+#define UCD9000_DEVICE_ID		0xfd
+
+#define UCD9000_MON_TYPE(x)	(((x) >> 5) & 0x07)
+#define UCD9000_MON_PAGE(x)	((x) & 0x0f)
+
+#define UCD9000_MON_VOLTAGE	1
+#define UCD9000_MON_TEMPERATURE	2
+#define UCD9000_MON_CURRENT	3
+#define UCD9000_MON_VOLTAGE_HW	4
+
+#define UCD9000_NUM_FAN		4
+
+struct ucd9000_data {
+	u8 fan_data[UCD9000_NUM_FAN][I2C_SMBUS_BLOCK_MAX];
+	struct pmbus_driver_info info;
+};
+#define to_ucd9000_data(_info) container_of(_info, struct ucd9000_data, info)
+
+static int ucd9000_get_fan_config(struct i2c_client *client, int fan)
+{
+	int fan_config = 0;
+	struct ucd9000_data *data
+	  = to_ucd9000_data(pmbus_get_driver_info(client));
+
+	if (data->fan_data[fan][3] & 1)
+		fan_config |= PB_FAN_2_INSTALLED;   /* Use lower bit position */
+
+	/* Pulses/revolution */
+	fan_config |= (data->fan_data[fan][3] & 0x06) >> 1;
+
+	return fan_config;
+}
+
+static int ucd9000_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+	int ret = 0;
+	int fan_config;
+
+	switch (reg) {
+	case PMBUS_FAN_CONFIG_12:
+		if (page)
+			return -EINVAL;
+
+		ret = ucd9000_get_fan_config(client, 0);
+		if (ret < 0)
+			return ret;
+		fan_config = ret << 4;
+		ret = ucd9000_get_fan_config(client, 1);
+		if (ret < 0)
+			return ret;
+		fan_config |= ret;
+		ret = fan_config;
+		break;
+	case PMBUS_FAN_CONFIG_34:
+		if (page)
+			return -EINVAL;
+
+		ret = ucd9000_get_fan_config(client, 2);
+		if (ret < 0)
+			return ret;
+		fan_config = ret << 4;
+		ret = ucd9000_get_fan_config(client, 3);
+		if (ret < 0)
+			return ret;
+		fan_config |= ret;
+		ret = fan_config;
+		break;
+	default:
+		ret = -ENODATA;
+		break;
+	}
+	return ret;
+}
+
+static const struct i2c_device_id ucd9000_id[] = {
+	{"ucd9000", ucd9000},
+	{"ucd90120", ucd90120},
+	{"ucd90124", ucd90124},
+	{"ucd9090", ucd9090},
+	{"ucd90910", ucd90910},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, ucd9000_id);
+
+static int ucd9000_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	u8 block_buffer[I2C_SMBUS_BLOCK_MAX + 1];
+	struct ucd9000_data *data;
+	struct pmbus_driver_info *info;
+	const struct i2c_device_id *mid;
+	int i, ret;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE_DATA |
+				     I2C_FUNC_SMBUS_BLOCK_DATA))
+		return -ENODEV;
+
+	ret = i2c_smbus_read_block_data(client, UCD9000_DEVICE_ID,
+					block_buffer);
+	if (ret < 0) {
+		dev_err(&client->dev, "Failed to read device ID\n");
+		return ret;
+	}
+	block_buffer[ret] = '\0';
+	dev_info(&client->dev, "Device ID %s\n", block_buffer);
+
+	mid = NULL;
+	for (i = 0; i < ARRAY_SIZE(ucd9000_id); i++) {
+		mid = &ucd9000_id[i];
+		if (!strncasecmp(mid->name, block_buffer, strlen(mid->name)))
+			break;
+	}
+	if (!mid || !strlen(mid->name)) {
+		dev_err(&client->dev, "Unsupported device\n");
+		return -ENODEV;
+	}
+
+	if (id->driver_data != ucd9000 && id->driver_data != mid->driver_data)
+		dev_notice(&client->dev,
+			   "Device mismatch: Configured %s, detected %s\n",
+			   id->name, mid->name);
+
+	data = kzalloc(sizeof(struct ucd9000_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+	info = &data->info;
+
+	ret = i2c_smbus_read_byte_data(client, UCD9000_NUM_PAGES);
+	if (ret < 0) {
+		dev_err(&client->dev,
+			"Failed to read number of active pages\n");
+		goto out;
+	}
+	info->pages = ret;
+	if (!info->pages) {
+		dev_err(&client->dev, "No pages configured\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	/* The internal temperature sensor is always active */
+	info->func[0] = PMBUS_HAVE_TEMP;
+
+	/* Everything else is configurable */
+	ret = i2c_smbus_read_block_data(client, UCD9000_MONITOR_CONFIG,
+					block_buffer);
+	if (ret <= 0) {
+		dev_err(&client->dev, "Failed to read configuration data\n");
+		ret = -ENODEV;
+		goto out;
+	}
+	for (i = 0; i < ret; i++) {
+		int page = UCD9000_MON_PAGE(block_buffer[i]);
+
+		if (page >= info->pages)
+			continue;
+
+		switch (UCD9000_MON_TYPE(block_buffer[i])) {
+		case UCD9000_MON_VOLTAGE:
+		case UCD9000_MON_VOLTAGE_HW:
+			info->func[page] |= PMBUS_HAVE_VOUT
+			  | PMBUS_HAVE_STATUS_VOUT;
+			break;
+		case UCD9000_MON_TEMPERATURE:
+			info->func[page] |= PMBUS_HAVE_TEMP2
+			  | PMBUS_HAVE_STATUS_TEMP;
+			break;
+		case UCD9000_MON_CURRENT:
+			info->func[page] |= PMBUS_HAVE_IOUT
+			  | PMBUS_HAVE_STATUS_IOUT;
+			break;
+		default:
+			break;
+		}
+	}
+
+	/* Fan configuration */
+	if (mid->driver_data == ucd90124) {
+		for (i = 0; i < UCD9000_NUM_FAN; i++) {
+			i2c_smbus_write_byte_data(client,
+						  UCD9000_FAN_CONFIG_INDEX, i);
+			ret = i2c_smbus_read_block_data(client,
+							UCD9000_FAN_CONFIG,
+							data->fan_data[i]);
+			if (ret < 0)
+				goto out;
+		}
+		i2c_smbus_write_byte_data(client, UCD9000_FAN_CONFIG_INDEX, 0);
+
+		info->read_byte_data = ucd9000_read_byte_data;
+		info->func[0] |= PMBUS_HAVE_FAN12 | PMBUS_HAVE_STATUS_FAN12
+		  | PMBUS_HAVE_FAN34 | PMBUS_HAVE_STATUS_FAN34;
+	}
+
+	ret = pmbus_do_probe(client, mid, info);
+	if (ret < 0)
+		goto out;
+	return 0;
+
+out:
+	kfree(data);
+	return ret;
+}
+
+static int ucd9000_remove(struct i2c_client *client)
+{
+	int ret;
+	struct ucd9000_data *data;
+
+	data = to_ucd9000_data(pmbus_get_driver_info(client));
+	ret = pmbus_do_remove(client);
+	kfree(data);
+	return ret;
+}
+
+
+/* This is the driver that will be inserted */
+static struct i2c_driver ucd9000_driver = {
+	.driver = {
+		.name = "ucd9000",
+	},
+	.probe = ucd9000_probe,
+	.remove = ucd9000_remove,
+	.id_table = ucd9000_id,
+};
+
+static int __init ucd9000_init(void)
+{
+	return i2c_add_driver(&ucd9000_driver);
+}
+
+static void __exit ucd9000_exit(void)
+{
+	i2c_del_driver(&ucd9000_driver);
+}
+
+MODULE_AUTHOR("Guenter Roeck");
+MODULE_DESCRIPTION("PMBus driver for TI UCD90xxx");
+MODULE_LICENSE("GPL");
+module_init(ucd9000_init);
+module_exit(ucd9000_exit);

drivers/hwmon/ucd9200.c

+/*
+ * Hardware monitoring driver for ucd9200 series Digital PWM System Controllers
+ *
+ * Copyright (C) 2011 Ericsson AB.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/i2c/pmbus.h>
+#include "pmbus.h"
+
+#define UCD9200_PHASE_INFO	0xd2
+#define UCD9200_DEVICE_ID	0xfd
+
+enum chips { ucd9200, ucd9220, ucd9222, ucd9224, ucd9240, ucd9244, ucd9246,
+	     ucd9248 };
+
+static const struct i2c_device_id ucd9200_id[] = {
+	{"ucd9200", ucd9200},
+	{"ucd9220", ucd9220},
+	{"ucd9222", ucd9222},
+	{"ucd9224", ucd9224},
+	{"ucd9240", ucd9240},
+	{"ucd9244", ucd9244},
+	{"ucd9246", ucd9246},
+	{"ucd9248", ucd9248},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, ucd9200_id);
+
+static int ucd9200_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	u8 block_buffer[I2C_SMBUS_BLOCK_MAX + 1];
+	struct pmbus_driver_info *info;
+	const struct i2c_device_id *mid;
+	int i, j, ret;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE_DATA |
+				     I2C_FUNC_SMBUS_BLOCK_DATA))
+		return -ENODEV;
+
+	ret = i2c_smbus_read_block_data(client, UCD9200_DEVICE_ID,
+					block_buffer);
+	if (ret < 0) {
+		dev_err(&client->dev, "Failed to read device ID\n");
+		return ret;
+	}
+	block_buffer[ret] = '\0';
+	dev_info(&client->dev, "Device ID %s\n", block_buffer);
+
+	mid = NULL;
+	for (i = 0; i < ARRAY_SIZE(ucd9200_id); i++) {
+		mid = &ucd9200_id[i];
+		if (!strncasecmp(mid->name, block_buffer, strlen(mid->name)))
+			break;
+	}
+	if (!mid || !strlen(mid->name)) {
+		dev_err(&client->dev, "Unsupported device\n");
+		return -ENODEV;
+	}
+	if (id->driver_data != ucd9200 && id->driver_data != mid->driver_data)
+		dev_notice(&client->dev,
+			   "Device mismatch: Configured %s, detected %s\n",
+			   id->name, mid->name);
+
+	info = kzalloc(sizeof(struct pmbus_driver_info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	ret = i2c_smbus_read_block_data(client, UCD9200_PHASE_INFO,
+					block_buffer);
+	if (ret < 0) {
+		dev_err(&client->dev, "Failed to read phase information\n");
+		goto out;
+	}
+
+	/*
+	 * Calculate number of configured pages (rails) from PHASE_INFO
+	 * register.
+	 * Rails have to be sequential, so we can abort after finding
+	 * the first unconfigured rail.
+	 */
+	info->pages = 0;
+	for (i = 0; i < ret; i++) {
+		if (!block_buffer[i])
+			break;
+		info->pages++;
+	}
+	if (!info->pages) {
+		dev_err(&client->dev, "No rails configured\n");
+		ret = -ENODEV;
+		goto out;
+	}
+	dev_info(&client->dev, "%d rails configured\n", info->pages);
+
+	/*
+	 * Set PHASE registers on all pages to 0xff to ensure that phase
+	 * specific commands will apply to all phases of a given page (rail).
+	 * This only affects the READ_IOUT and READ_TEMPERATURE2 registers.
+	 * READ_IOUT will return the sum of currents of all phases of a rail,
+	 * and READ_TEMPERATURE2 will return the maximum temperature detected
+	 * for the the phases of the rail.
+	 */
+	for (i = 0; i < info->pages; i++) {
+		/*
+		 * Setting PAGE & PHASE fails once in a while for no obvious
+		 * reason, so we need to retry a couple of times.
+		 */
+		for (j = 0; j < 3; j++) {
+			ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, i);
+			if (ret < 0)
+				continue;
+			ret = i2c_smbus_write_byte_data(client, PMBUS_PHASE,
+							0xff);
+			if (ret < 0)
+				continue;
+			break;
+		}
+		if (ret < 0) {
+			dev_err(&client->dev,
+				"Failed to initialize PHASE registers\n");
+			goto out;
+		}
+	}
+	if (info->pages > 1)
+		i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
+
+	info->func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT |
+			PMBUS_HAVE_IIN | PMBUS_HAVE_PIN |
+			PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+			PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+			PMBUS_HAVE_POUT | PMBUS_HAVE_TEMP |
+			PMBUS_HAVE_TEMP2 | PMBUS_HAVE_STATUS_TEMP;
+
+	for (i = 1; i < info->pages; i++)
+		info->func[i] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+			PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+			PMBUS_HAVE_POUT |
+			PMBUS_HAVE_TEMP2 | PMBUS_HAVE_STATUS_TEMP;
+
+	/* ucd9240 supports a single fan */
+	if (mid->driver_data == ucd9240)
+		info->func[0] |= PMBUS_HAVE_FAN12 | PMBUS_HAVE_STATUS_FAN12;
+
+	ret = pmbus_do_probe(client, mid, info);
+	if (ret < 0)
+		goto out;
+	return 0;
+out:
+	kfree(info);
+	return ret;
+}
+
+static int ucd9200_remove(struct i2c_client *client)
+{
+	int ret;
+	const struct pmbus_driver_info *info;
+
+	info = pmbus_get_driver_info(client);
+	ret = pmbus_do_remove(client);
+	kfree(info);
+	return ret;
+}
+
+
+/* This is the driver that will be inserted */
+static struct i2c_driver ucd9200_driver = {
+	.driver = {
+		.name = "ucd9200",
+	},
+	.probe = ucd9200_probe,
+	.remove = ucd9200_remove,
+	.id_table = ucd9200_id,
+};
+
+static int __init ucd9200_init(void)
+{
+	return i2c_add_driver(&ucd9200_driver);
+}
+
+static void __exit ucd9200_exit(void)
+{
+	i2c_del_driver(&ucd9200_driver);
+}
+
+MODULE_AUTHOR("Guenter Roeck");
+MODULE_DESCRIPTION("PMBus driver for TI UCD922x, UCD924x");
+MODULE_LICENSE("GPL");
+module_init(ucd9200_init);
+module_exit(ucd9200_exit);

include/linux/sht15.h

@@ -8,17 +8,27 @@
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
+ *
+ * For further information, see the Documentation/hwmon/sht15 file.
  */
 
 /**
  * struct sht15_platform_data - sht15 connectivity info
- * @gpio_data:	no. of gpio to which bidirectional data line is connected
- * @gpio_sck:	no. of gpio to which the data clock is connected.
- * @supply_mv:	supply voltage in mv. Overridden by regulator if available.
- **/
+ * @gpio_data:		no. of gpio to which bidirectional data line is
+ *			connected.
+ * @gpio_sck:		no. of gpio to which the data clock is connected.
+ * @supply_mv:		supply voltage in mv. Overridden by regulator if
+ *			available.
+ * @checksum:		flag to indicate the checksum should be validated.
+ * @no_otp_reload:	flag to indicate no reload from OTP.
+ * @low_resolution:	flag to indicate the temp/humidity resolution to use.
+ */
 struct sht15_platform_data {
 	int gpio_data;
 	int gpio_sck;
 	int supply_mv;
+	bool checksum;
+	bool no_otp_reload;
+	bool low_resolution;
 };