Merge branch 'Add-packet-trap-policers-support'
Ido Schimmel says:
====================
Add packet trap policers support
Background
==========
Devices capable of offloading the kernel's datapath and perform
functions such as bridging and routing must also be able to send (trap)
specific packets to the kernel (i.e., the CPU) for processing.
For example, a device acting as a multicast-aware bridge must be able to
trap IGMP membership reports to the kernel for processing by the bridge
module.
Motivation
==========
In most cases, the underlying device is capable of handling packet rates
that are several orders of magnitude higher compared to those that can
be handled by the CPU.
Therefore, in order to prevent the underlying device from overwhelming
the CPU, devices usually include packet trap policers that are able to
police the trapped packets to rates that can be handled by the CPU.
Proposed solution
=================
This patch set allows capable device drivers to register their supported
packet trap policers with devlink. User space can then tune the
parameters of these policers (currently, rate and burst size) and read
from the device the number of packets that were dropped by the policer,
if supported.
These packet trap policers can then be bound to existing packet trap
groups, which are used to aggregate logically related packet traps. As a
result, trapped packets are policed to rates that can be handled the
host CPU.
Example usage
=============
Instantiate netdevsim:
Dump available packet trap policers:
netdevsim/netdevsim10:
policer 1 rate 1000 burst 128
policer 2 rate 2000 burst 256
policer 3 rate 3000 burst 512
Change the parameters of a packet trap policer:
Bind a packet trap policer to a packet trap group:
Dump parameters and statistics of a packet trap policer:
netdevsim/netdevsim10:
policer 3 rate 100 burst 16
stats:
rx:
dropped 92
Unbind a packet trap policer from a packet trap group:
Patch set overview
==================
Patch #1 adds the core infrastructure in devlink which allows capable
device drivers to register their supported packet trap policers with
devlink.
Patch #2 extends the existing devlink-trap documentation.
Patch #3 extends netdevsim to register a few dummy packet trap policers
with devlink. Used later on to selftests the core infrastructure.
Patches #4-#5 adds infrastructure in devlink to allow binding of packet
trap policers to packet trap groups.
Patch #6 extends netdevsim to allow such binding.
Patch #7 adds a selftest over netdevsim that verifies the core
devlink-trap policers functionality.
Patches #8-#14 gradually add devlink-trap policers support in mlxsw.
Patch #15 adds a selftest over mlxsw. All registered packet trap
policers are verified to handle the configured rate and burst size.
Future plans
============
* Allow changing default association between packet traps and packet
trap groups
* Add more packet traps. For example, for control packets (e.g., IGMP)
v3:
* Rebase
v2 (address comments from Jiri and Jakub):
* Patch #1: Add 'strict_start_type' in devlink policy
* Patch #1: Have device drivers provide max/min rate/burst size for each
policer. Use them to check validity of user provided parameters
* Patch #3: Remove check about burst size being a power of 2 and instead
add a debugfs knob to fail the operation
* Patch #3: Provide max/min rate/burst size when registering policers
and remove the validity checks from nsim_dev_devlink_trap_policer_set()
* Patch #5: Check for presence of 'DEVLINK_ATTR_TRAP_POLICER_ID' in
devlink_trap_group_set() and bail if not present
* Patch #5: Add extack error message in case trap group was partially
modified
* Patch #7: Add test case with new 'fail_trap_policer_set' knob
* Patch #7: Add test case for partially modified trap group
* Patch #10: Provide max/min rate/burst size when registering policers
* Patch #11: Remove the max/min validity checks from
__mlxsw_sp_trap_policer_set()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Showing
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
Please register or sign in to comment