Commit 730d7dcf authored by Adam Ford's avatar Adam Ford Committed by Tony Lindgren

ARM: dts: omap3logic: Add PWM-Backlight

The backlight pin is shared with Timer 10 PWM.  This patch allows the
pwm_bl driver to enable the pwm run by this timer to dim the backlight.
Signed-off-by: default avatarAdam Ford <aford173@gmail.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent 05cf1e03
...@@ -71,6 +71,15 @@ led2 { ...@@ -71,6 +71,15 @@ led2 {
linux,default-trigger = "none"; linux,default-trigger = "none";
}; };
}; };
pwm10: dmtimer-pwm@10 {
compatible = "ti,omap-dmtimer-pwm";
pinctrl-names = "default";
pinctrl-0 = <&pwm_pins>;
ti,timers = <&timer10>;
#pwm-cells = <3>;
};
}; };
&vaux1 { &vaux1 {
...@@ -168,13 +177,13 @@ panel-timing { ...@@ -168,13 +177,13 @@ panel-timing {
}; };
bl: backlight { bl: backlight {
compatible = "gpio-backlight"; compatible = "pwm-backlight";
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&backlight_pins>; pinctrl-0 = <&backlight_pins>;
pwms = <&pwm10 0 5000000 0>;
gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>, /* gpio_154 */ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
<&gpio2 24 GPIO_ACTIVE_HIGH>; /* gpio_56 */ default-brightness-level = <7>;
default-on; enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */
}; };
}; };
...@@ -196,6 +205,12 @@ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_cs0.gpio_181 * ...@@ -196,6 +205,12 @@ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_cs0.gpio_181 *
>; >;
}; };
pwm_pins: pinmux_pwm_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */
>;
};
led_pins: pinmux_led_pins { led_pins: pinmux_led_pins {
pinctrl-single,pins = < pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */ OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */
...@@ -222,7 +237,6 @@ OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ ...@@ -222,7 +237,6 @@ OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */
backlight_pins: pinmux_backlight_pins { backlight_pins: pinmux_backlight_pins {
pinctrl-single,pins = < pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* gpmc_ncs5.gpio_56 */
OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */ OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */
>; >;
}; };
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment