Commit 754c653a authored by Ben Hutchings's avatar Ben Hutchings Committed by David S. Miller

sfc: Fix some incorrect or redundant comments

In particular, the comment about EVQ_RPTR_REG is based on inconsistent
preliminary hardware documentation, though the following code was
fixed long before release.
Signed-off-by: default avatarBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 2291b20f
......@@ -196,7 +196,7 @@ int efx_ethtool_get_settings(struct net_device *net_dev,
efx->phy_op->get_settings(efx, ecmd);
mutex_unlock(&efx->mac_lock);
/* Falcon GMAC does not support 1000Mbps HD */
/* GMAC does not support 1000Mbps HD */
ecmd->supported &= ~SUPPORTED_1000baseT_Half;
/* Both MACs support pause frames (bidirectional and respond-only) */
ecmd->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
......@@ -216,7 +216,7 @@ int efx_ethtool_set_settings(struct net_device *net_dev,
struct efx_nic *efx = netdev_priv(net_dev);
int rc;
/* Falcon GMAC does not support 1000Mbps HD */
/* GMAC does not support 1000Mbps HD */
if (ecmd->speed == SPEED_1000 && ecmd->duplex != DUPLEX_FULL) {
EFX_LOG(efx, "rejecting unsupported 1000Mbps HD"
" setting\n");
......
......@@ -1730,7 +1730,7 @@ static int falcon_set_wol(struct efx_nic *efx, u32 type)
/**************************************************************************
*
* Revision-dependent attributes used by efx.c
* Revision-dependent attributes used by efx.c and nic.c
*
**************************************************************************
*/
......
......@@ -101,9 +101,6 @@ do {if (net_ratelimit()) EFX_LOG(efx, fmt, ##args); } while (0)
* Special buffers are used for the event queues and the TX and RX
* descriptor queues for each channel. They are *not* used for the
* actual transmit and receive buffers.
*
* Note that for Falcon, TX and RX descriptor queues live in host memory.
* Allocation and freeing procedures must take this into account.
*/
struct efx_special_buffer {
void *addr;
......@@ -300,7 +297,7 @@ struct efx_rx_queue {
* @dma_addr: DMA base address of the buffer
* @len: Buffer length, in bytes
*
* Falcon uses these buffers for its interrupt status registers and
* The NIC uses these buffers for its interrupt status registers and
* MAC stats dumps.
*/
struct efx_buffer {
......@@ -674,7 +671,7 @@ union efx_multicast_hash {
* @irq_status: Interrupt status buffer
* @last_irq_cpu: Last CPU to handle interrupt.
* This register is written with the SMP processor ID whenever an
* interrupt is handled. It is used by falcon_test_interrupt()
* interrupt is handled. It is used by efx_nic_test_interrupt()
* to verify that an interrupt has occurred.
* @spi_flash: SPI flash device
* This field will be %NULL if no flash device is present (or for Siena).
......@@ -723,8 +720,7 @@ union efx_multicast_hash {
* @loopback_modes: Supported loopback mode bitmask
* @loopback_selftest: Offline self-test private state
*
* The @priv field of the corresponding &struct net_device points to
* this.
* This is stored in the private area of the &struct net_device.
*/
struct efx_nic {
char name[IFNAMSIZ];
......@@ -997,7 +993,7 @@ static inline void clear_bit_le(unsigned nr, unsigned char *addr)
* that the net driver will program into the MAC as the maximum frame
* length.
*
* The 10G MAC used in Falcon requires 8-byte alignment on the frame
* The 10G MAC requires 8-byte alignment on the frame
* length, so we round up to the nearest 8.
*
* Re-clocking by the XGXS on RX can reduce an IPG to 32 bits (half an
......
......@@ -623,10 +623,6 @@ void efx_nic_remove_rx(struct efx_rx_queue *rx_queue)
*
* This writes the EVQ_RPTR_REG register for the specified channel's
* event queue.
*
* Note that EVQ_RPTR_REG contains the index of the "last read" event,
* whereas channel->eventq_read_ptr contains the index of the "next to
* read" event.
*/
void efx_nic_eventq_read_ack(struct efx_channel *channel)
{
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment