Commit 7640335e authored by Andrew Vasquez's avatar Andrew Vasquez Committed by James Bottomley

[SCSI] qla2xxx: Correct compilation failures when DEBUG'n' options are enabled.

Signed-off-by: default avatarAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@HansenPartnership.com>
parent bad7001c
......@@ -634,7 +634,7 @@ qla2x00_chip_diag(scsi_qla_host_t *vha)
goto chip_diag_failed;
DEBUG3(printk("scsi(%ld): Reset register cleared by chip reset\n",
ha->host_no));
vha->host_no));
/* Reset RISC processor. */
WRT_REG_WORD(&reg->hccr, HCCR_RESET_RISC);
......@@ -655,7 +655,7 @@ qla2x00_chip_diag(scsi_qla_host_t *vha)
goto chip_diag_failed;
/* Check product ID of chip */
DEBUG3(printk("scsi(%ld): Checking product ID of chip\n", ha->host_no));
DEBUG3(printk("scsi(%ld): Checking product ID of chip\n", vha->host_no));
mb[1] = RD_MAILBOX_REG(ha, reg, 1);
mb[2] = RD_MAILBOX_REG(ha, reg, 2);
......@@ -2110,7 +2110,7 @@ qla2x00_configure_local_loop(scsi_qla_host_t *vha)
goto cleanup_allocation;
DEBUG3(printk("scsi(%ld): Entries in ID list (%d)\n",
ha->host_no, entries));
vha->host_no, entries));
DEBUG3(qla2x00_dump_buffer((uint8_t *)ha->gid_list,
entries * sizeof(struct gid_list_info)));
......@@ -3587,7 +3587,7 @@ qla24xx_nvram_config(scsi_qla_host_t *vha)
for (cnt = 0, chksum = 0; cnt < ha->nvram_size >> 2; cnt++)
chksum += le32_to_cpu(*dptr++);
DEBUG5(printk("scsi(%ld): Contents of NVRAM\n", ha->host_no));
DEBUG5(printk("scsi(%ld): Contents of NVRAM\n", vha->host_no));
DEBUG5(qla2x00_dump_buffer((uint8_t *)nv, ha->nvram_size));
/* Bad NVRAM data, set defaults parameters. */
......@@ -4305,7 +4305,7 @@ qla81xx_nvram_config(scsi_qla_host_t *vha)
for (cnt = 0, chksum = 0; cnt < ha->nvram_size >> 2; cnt++)
chksum += le32_to_cpu(*dptr++);
DEBUG5(printk("scsi(%ld): Contents of NVRAM\n", ha->host_no));
DEBUG5(printk("scsi(%ld): Contents of NVRAM\n", vha->host_no));
DEBUG5(qla2x00_dump_buffer((uint8_t *)nv, ha->nvram_size));
/* Bad NVRAM data, set defaults parameters. */
......
......@@ -3393,7 +3393,7 @@ qla2x00_read_edc(scsi_qla_host_t *vha, uint16_t dev, uint16_t adr,
DEBUG2_3_11(printk("%s(%ld): failed=%x (%x).\n", __func__,
vha->host_no, rval, mcp->mb[0]));
} else {
DEBUG11(printk("%s(%ld): done.\n", __func__, ha->host_no));
DEBUG11(printk("%s(%ld): done.\n", __func__, vha->host_no));
}
return rval;
......
......@@ -219,8 +219,8 @@ qla2x00_write_nvram_word(struct qla_hw_data *ha, uint32_t addr, uint16_t data)
wait_cnt = NVR_WAIT_CNT;
do {
if (!--wait_cnt) {
DEBUG9_10(printk("%s(%ld): NVRAM didn't go ready...\n",
__func__, vha->host_no));
DEBUG9_10(qla_printk(KERN_WARNING, ha,
"NVRAM didn't go ready...\n"));
break;
}
NVRAM_DELAY();
......@@ -349,7 +349,7 @@ qla2x00_clear_nvram_protection(struct qla_hw_data *ha)
wait_cnt = NVR_WAIT_CNT;
do {
if (!--wait_cnt) {
DEBUG9_10(qla_printk(
DEBUG9_10(qla_printk(KERN_WARNING, ha,
"NVRAM didn't go ready...\n"));
break;
}
......@@ -408,7 +408,8 @@ qla2x00_set_nvram_protection(struct qla_hw_data *ha, int stat)
wait_cnt = NVR_WAIT_CNT;
do {
if (!--wait_cnt) {
DEBUG9_10(qla_printk("NVRAM didn't go ready...\n"));
DEBUG9_10(qla_printk(KERN_WARNING, ha,
"NVRAM didn't go ready...\n"));
break;
}
NVRAM_DELAY();
......@@ -1079,8 +1080,9 @@ qla24xx_write_flash_data(scsi_qla_host_t *vha, uint32_t *dwptr, uint32_t faddr,
0xff0000) | ((fdata >> 16) & 0xff));
ret = qla24xx_erase_sector(vha, fdata);
if (ret != QLA_SUCCESS) {
DEBUG9(qla_printk("Unable to erase sector: "
"address=%x.\n", faddr));
DEBUG9(qla_printk(KERN_WARNING, ha,
"Unable to erase sector: address=%x.\n",
faddr));
break;
}
}
......@@ -1240,8 +1242,9 @@ qla24xx_write_nvram_data(scsi_qla_host_t *vha, uint8_t *buf, uint32_t naddr,
ret = qla24xx_write_flash_dword(ha,
nvram_data_addr(ha, naddr), cpu_to_le32(*dwptr));
if (ret != QLA_SUCCESS) {
DEBUG9(qla_printk("Unable to program nvram address=%x "
"data=%x.\n", naddr, *dwptr));
DEBUG9(qla_printk(KERN_WARNING, ha,
"Unable to program nvram address=%x data=%x.\n",
naddr, *dwptr));
break;
}
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment