Commit 78709b9d authored by Ralf Baechle's avatar Ralf Baechle

[MIPS] IP22: Get rid of volatile in IP22 core code.

Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent 2127435e
......@@ -52,8 +52,7 @@
* national semiconductor nv ram chip the op code is 3 bits and
* the address is 6/8 bits.
*/
static inline void eeprom_cmd(volatile unsigned int *ctrl, unsigned cmd,
unsigned reg)
static inline void eeprom_cmd(unsigned int *ctrl, unsigned cmd, unsigned reg)
{
unsigned short ser_cmd;
int i;
......@@ -61,33 +60,34 @@ static inline void eeprom_cmd(volatile unsigned int *ctrl, unsigned cmd,
ser_cmd = cmd | (reg << (16 - BITS_IN_COMMAND));
for (i = 0; i < BITS_IN_COMMAND; i++) {
if (ser_cmd & (1<<15)) /* if high order bit set */
*ctrl |= EEPROM_DATO;
writel(readl(ctrl) | EEPROM_DATO, ctrl);
else
*ctrl &= ~EEPROM_DATO;
*ctrl &= ~EEPROM_ECLK;
*ctrl |= EEPROM_ECLK;
writel(readl(ctrl) & ~EEPROM_DATO, ctrl);
writel(readl(ctrl) & ~EEPROM_ECLK, ctrl);
writel(readl(ctrl) | EEPROM_ECLK, ctrl);
ser_cmd <<= 1;
}
*ctrl &= ~EEPROM_DATO; /* see data sheet timing diagram */
/* see data sheet timing diagram */
writel(readl(ctrl) & ~EEPROM_DATO, ctrl);
}
unsigned short ip22_eeprom_read(volatile unsigned int *ctrl, int reg)
unsigned short ip22_eeprom_read(unsigned int *ctrl, int reg)
{
unsigned short res = 0;
int i;
*ctrl &= ~EEPROM_EPROT;
writel(readl(ctrl) & ~EEPROM_EPROT, ctrl);
eeprom_cs_on(ctrl);
eeprom_cmd(ctrl, EEPROM_READ, reg);
/* clock the data ouf of serial mem */
for (i = 0; i < 16; i++) {
*ctrl &= ~EEPROM_ECLK;
writel(readl(ctrl) & ~EEPROM_ECLK, ctrl);
delay();
*ctrl |= EEPROM_ECLK;
writel(readl(ctrl) | EEPROM_ECLK, ctrl);
delay();
res <<= 1;
if (*ctrl & EEPROM_DATI)
if (readl(ctrl) & EEPROM_DATI)
res |= 1;
}
......
......@@ -94,7 +94,7 @@ static int indy_rtc_set_time(unsigned long tim)
static unsigned long dosample(void)
{
u32 ct0, ct1;
volatile u8 msb, lsb;
u8 msb, lsb;
/* Start the counter. */
sgint->tcword = (SGINT_TCWORD_CNT2 | SGINT_TCWORD_CALL |
......@@ -107,21 +107,21 @@ static unsigned long dosample(void)
/* Latch and spin until top byte of counter2 is zero */
do {
sgint->tcword = SGINT_TCWORD_CNT2 | SGINT_TCWORD_CLAT;
lsb = sgint->tcnt2;
msb = sgint->tcnt2;
writeb(SGINT_TCWORD_CNT2 | SGINT_TCWORD_CLAT, &sgint->tcword);
lsb = readb(&sgint->tcnt2);
msb = readb(&sgint->tcnt2);
ct1 = read_c0_count();
} while (msb);
/* Stop the counter. */
sgint->tcword = (SGINT_TCWORD_CNT2 | SGINT_TCWORD_CALL |
SGINT_TCWORD_MSWST);
writeb(sgint->tcword, (SGINT_TCWORD_CNT2 | SGINT_TCWORD_CALL |
SGINT_TCWORD_MSWST));
/*
* Return the difference, this is how far the r4k counter increments
* for every 1/HZ seconds. We round off the nearest 1 MHz of master
* clock (= 1000000 / HZ / 2).
*/
/*return (ct1 - ct0 + (500000/HZ/2)) / (500000/HZ) * (500000/HZ);*/
return (ct1 - ct0) / (500000/HZ) * (500000/HZ);
}
......
......@@ -206,7 +206,7 @@ struct hpc3_regs {
#define HPC3_GIOMISC_ERTIME 0x1 /* Enable external timer real time. */
#define HPC3_GIOMISC_DENDIAN 0x2 /* dma descriptor endian, 1=lit 0=big */
volatile u32 eeprom; /* EEPROM data reg. */
u32 eeprom; /* EEPROM data reg. */
#define HPC3_EEPROM_EPROT 0x01 /* Protect register enable */
#define HPC3_EEPROM_CSEL 0x02 /* Chip select */
#define HPC3_EEPROM_ECLK 0x04 /* EEPROM clock */
......
......@@ -72,7 +72,7 @@
#define ip22_is_fullhouse() (sgioc->sysid & SGIOC_SYSID_FULLHOUSE)
extern unsigned short ip22_eeprom_read(volatile unsigned int *ctrl, int reg);
extern unsigned short ip22_eeprom_read(unsigned int *ctrl, int reg);
extern unsigned short ip22_nvram_read(int reg);
#endif
......@@ -57,7 +57,7 @@ struct sgimc_regs {
volatile u32 divider; /* Divider reg for RPSS */
u32 _unused5;
volatile u32 eeprom; /* EEPROM byte reg for r4k */
u32 eeprom; /* EEPROM byte reg for r4k */
#define SGIMC_EEPROM_PRE 0x00000001 /* eeprom chip PRE pin assertion */
#define SGIMC_EEPROM_CSEL 0x00000002 /* Active high, eeprom chip select */
#define SGIMC_EEPROM_SECLOCK 0x00000004 /* EEPROM serial clock */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment