Commit 797622d7 authored by Alban Bedel's avatar Alban Bedel Committed by Mark Brown

spi: ath79: Simplify ath79_spi_chipselect()

First of all this callback was slightly misused to setup the clock
polarity at the beginning of a transfer. Beside being at the wrong
place, it is also useless as only SPI mode 1 is supported. Instead
just make sure the base value used for IOC is suitable to start a
transfer by clearing the clock and data bits during the controller
setup.

This also remove the last direct usage of the GPIO API, so we can
remove the direct dependency on GPIOLIB.
Signed-off-by: default avatarAlban Bedel <albeu@free.fr>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
parent a666f261
......@@ -63,7 +63,7 @@ config SPI_ALTERA
config SPI_ATH79
tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
depends on ATH79 && GPIOLIB
depends on ATH79
select SPI_BITBANG
help
This enables support for the SPI controller present on the
......
......@@ -21,7 +21,6 @@
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/bitops.h>
#include <linux/gpio/consumer.h>
#include <linux/clk.h>
#include <linux/err.h>
......@@ -67,38 +66,14 @@ static void ath79_spi_chipselect(struct spi_device *spi, int is_active)
{
struct ath79_spi *sp = ath79_spidev_to_sp(spi);
int cs_high = (spi->mode & SPI_CS_HIGH) ? is_active : !is_active;
u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
if (is_active) {
/* set initial clock polarity */
if (spi->mode & SPI_CPOL)
sp->ioc_base |= AR71XX_SPI_IOC_CLK;
else
sp->ioc_base &= ~AR71XX_SPI_IOC_CLK;
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
if (spi->cs_gpiod) {
/*
* SPI chipselect is normally active-low, but
* inversion semantics are handled by gpiolib.
*
* FIXME: is this ever used? The driver doesn't
* set SPI_MASTER_GPIO_SS so this callback should not
* get called if a CS GPIO is found by the SPI core.
*/
gpiod_set_value_cansleep(spi->cs_gpiod, is_active);
} else {
u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
if (cs_high)
sp->ioc_base |= cs_bit;
else
sp->ioc_base &= ~cs_bit;
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
if (cs_high)
sp->ioc_base |= cs_bit;
else
sp->ioc_base &= ~cs_bit;
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
static void ath79_spi_enable(struct ath79_spi *sp)
......@@ -110,6 +85,9 @@ static void ath79_spi_enable(struct ath79_spi *sp)
sp->reg_ctrl = ath79_spi_rr(sp, AR71XX_SPI_REG_CTRL);
sp->ioc_base = ath79_spi_rr(sp, AR71XX_SPI_REG_IOC);
/* clear clk and mosi in the base state */
sp->ioc_base &= ~(AR71XX_SPI_IOC_DO | AR71XX_SPI_IOC_CLK);
/* TODO: setup speed? */
ath79_spi_wr(sp, AR71XX_SPI_REG_CTRL, 0x43);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment