Merge bk://24.221.152.185/linux-2.5-misc

into samba.org:/home/paulus/kernel/for-linus-ppc

arch/ppc/8260_io/Config.help

@@ -22,3 +22,6 @@ CONFIG_SCC1_ENET
 CONFIG_SCC2_ENET
   Use MPC8xx serial communications controller 2 to drive Ethernet.
 
+CONFIG_DCACHE_DISABLE
+  This option allows you to run the kernel with data cache disabled.
+  Say Y if you experience CPM lock-ups.

arch/ppc/8260_io/Config.in

@@ -2,7 +2,7 @@
 # MPC8260 Communication options
 #
 mainmenu_option next_comment
-comment 'MPC8260 Communication Options'
+comment 'MPC8260 CPM Options'
 bool 'Enable SCC Console' CONFIG_SCC_CONSOLE
 if [ "$CONFIG_NET_ETHERNET" = "y" ]; then
   bool 'CPM SCC Ethernet' CONFIG_SCC_ENET
@@ -30,4 +30,7 @@ if [ "$CONFIG_NET_ETHERNET" = "y" ]; then
       fi
   fi
 fi
+
+comment 'Generic MPC8260 Options'
+bool 'Disable data cache' CONFIG_DCACHE_DISABLE
 endmenu

arch/ppc/boot/chrp/Makefile

@@ -11,7 +11,11 @@ LD_ARGS = -T ../ld.script -Ttext 0x00400000
 
 OBJS = ../common/crt0.o start.o main.o misc.o ../common/string.o image.o \
 	../common/ofcommon.o
+
+EXTRA_TARGETS	:= $(OBJS)
 LIBS = $(TOPDIR)/lib/lib.a ../lib/zlib.a
+
+# Utils
 ADDNOTE = ../utils/addnote
 PIGGYBACK = ../utils/piggyback
 

arch/ppc/boot/pmac/Makefile

@@ -15,6 +15,8 @@ CHRP_LD_ARGS = -T ../ld.script -Ttext 0x01000000
 COMMONOBJS = start.o misc.o ../common/string.o ../common/ofcommon.o
 COFFOBJS = ../common/coffcrt0.o $(COMMONOBJS) coffmain.o
 CHRPOBJS = ../common/crt0.o $(COMMONOBJS) chrpmain.o
+
+EXTRA_TARGETS	:= $(COFFOBJS) $(CHRPOBJS)
 LIBS = $(TOPDIR)/lib/lib.a ../lib/zlib.a
 
 MKNOTE := ../utils/mknote

arch/ppc/boot/prep/Makefile

@@ -30,6 +30,8 @@ LIBS 				= ../lib/zlib.a
 boot-$(CONFIG_SERIAL_CONSOLE)	+= ../common/ns16550.o
 boot-$(CONFIG_VGA_CONSOLE)	+= vreset.o kbd.o
 
+EXTRA_TARGETS			:= $(boot-y)
+
 # Tools
 MKPREP				:= ../utils/mkprep
 SIZE				:= ../utils/size

arch/ppc/boot/simple/Makefile

@@ -140,6 +140,7 @@ boot-$(CONFIG_GT64260_CONSOLE)   += gt64260_tty.o
 boot-$(CONFIG_SERIAL)		+= ../common/ns16550.o
 endif
 
+EXTRA_TARGETS			:= $(boot-y)
 LIBS				:= ../lib/zlib.a
 
 # Tools

arch/ppc/configs/est8260_defconfig

@@ -421,6 +421,7 @@ CONFIG_PARTITION_ADVANCED=y
 CONFIG_SCC_ENET=y
 CONFIG_SCC1_ENET=y
 # CONFIG_FEC_ENET is not set
+# CONFIG_DCACHE_DISABLE is not set
 
 #
 # USB support

arch/ppc/kernel/head.S

@@ -1272,7 +1272,11 @@ _GLOBAL(__setup_cpu_generic)
 setup_common_caches:
 	mfspr	r11,HID0
 	andi.	r0,r11,HID0_DCE
+#ifdef CONFIG_DCACHE_DISABLE
+	ori	r11,r11,HID0_ICE
+#else
 	ori	r11,r11,HID0_ICE|HID0_DCE
+#endif
 	ori	r8,r11,HID0_ICFI
 	bne	1f			/* don't invalidate the D-cache */
 	ori	r8,r8,HID0_DCI		/* unless it wasn't enabled */

arch/ppc/platforms/mbx.h

@@ -88,11 +88,33 @@ typedef struct bd_info {
 #define ISA_BRIDGE_INT	SIU_IRQ3	/* All those PC things */
 #define COMM_L_INT	SIU_IRQ6	/* MBX Comm expansion connector pin */
 #define STOP_ABRT_INT	SIU_IRQ7	/* Stop/Abort header pin */
-#endif /* !__ASSEMBLY__ */
+
+/* CPM Ethernet through SCCx.
+ *
+ * Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.  The TCLK and RCLK seem unique
+ * to the MBX860 board.  Any two of the four available clocks could be
+ * used, and the MPC860 cookbook manual has an example using different
+ * clock pins.
+ */
+#define PA_ENET_RXD	((ushort)0x0001)
+#define PA_ENET_TXD	((ushort)0x0002)
+#define PA_ENET_TCLK	((ushort)0x0200)
+#define PA_ENET_RCLK	((ushort)0x0800)
+#define PC_ENET_TENA	((ushort)0x0001)
+#define PC_ENET_CLSN	((ushort)0x0010)
+#define PC_ENET_RENA	((ushort)0x0020)
+
+/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
+ * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x000000ff)
+#define SICR_ENET_CLKRT	((uint)0x0000003d)
 
 /* The MBX uses the 8259.
 */
 #define NR_8259_INTS	16
 
-#endif
+#endif /* !__ASSEMBLY__ */
+#endif /* __MACH_MBX_DEFS */
 #endif /* __KERNEL__ */

arch/ppc/platforms/rpxclassic.h

@@ -94,11 +94,31 @@ extern bd_t m8xx_board_info;
 */
 #define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */
 
-#endif /* !__ASSEMBLY__ */
+
+/* CPM Ethernet through SCCx.
+ *
+ * Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PA_ENET_RXD	((ushort)0x0001)
+#define PA_ENET_TXD	((ushort)0x0002)
+#define PA_ENET_TCLK	((ushort)0x0200)
+#define PA_ENET_RCLK	((ushort)0x0800)
+#define PB_ENET_TENA	((uint)0x00001000)
+#define PC_ENET_CLSN	((ushort)0x0010)
+#define PC_ENET_RENA	((ushort)0x0020)
+
+/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
+ * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x000000ff)
+#define SICR_ENET_CLKRT	((uint)0x0000003d)
 
 /* We don't use the 8259.
 */
+
 #define NR_8259_INTS	0
 
-#endif
+#endif /* !__ASSEMBLY__ */
+#endif /* __MACH_RPX_DEFS */
 #endif /* __KERNEL__ */

arch/ppc/platforms/rpxlite.h

@@ -65,7 +65,6 @@ extern bd_t m8xx_board_info;
 #if defined(CONFIG_HTDMSOUND)
 #include <platforms/rpxhiox.h>
 #endif
-#endif /* !__ASSEMBLY__ */
 
 /* define IO_BASE for pcmcia */
 #define _IO_BASE 0x80000000
@@ -76,9 +75,27 @@ extern bd_t m8xx_board_info;
 # define request_irq(irq,hand,flg,dev,id)    request_8xxirq((irq),(hand),(flg),(dev),(id))
 #endif
 
+/* CPM Ethernet through SCCx.
+ *
+ * This ENET stuff is for the MPC850 with ethernet on SCC2.  Some of
+ * this may be unique to the RPX-Lite configuration.
+ * Note TENA is on Port B.
+ */
+#define PA_ENET_RXD	((ushort)0x0004)
+#define PA_ENET_TXD	((ushort)0x0008)
+#define PA_ENET_TCLK	((ushort)0x0200)
+#define PA_ENET_RCLK	((ushort)0x0800)
+#define PB_ENET_TENA	((uint)0x00002000)
+#define PC_ENET_CLSN	((ushort)0x0040)
+#define PC_ENET_RENA	((ushort)0x0080)
+
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00003d00)
+
 /* We don't use the 8259.
 */
 #define NR_8259_INTS	0
 
-#endif
+#endif /* !__ASSEMBLY__ */
+#endif /* __MACH_RPX_DEFS */
 #endif /* __KERNEL__ */

arch/ppc/platforms/spd8xx.h

@@ -15,6 +15,7 @@
  
 #include <asm/ppcboot.h>
 
+#ifndef __ASSEMBLY__
 #define SPD_IMMR_BASE	0xFFF00000	/* phys. addr of IMMR */
 #define SPD_IMAP_SIZE	(64 * 1024)	/* size of mapped area */
 
@@ -61,9 +62,34 @@
 #define IDE1_CONTROL_REG_OFFSET		0x0106
 #define IDE1_IRQ_REG_OFFSET		0x000A	/* not used */
 
+/* CPM Ethernet through SCCx.
+ *
+ * Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PA_ENET_MDC	((ushort)0x0001)	/* PA 15 !!! */
+#define PA_ENET_MDIO	((ushort)0x0002)	/* PA 14 !!! */
+#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
+#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
+#define PA_ENET_RCLK	((ushort)0x0200)	/* PA  6 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
+
+#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
+#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+#define PC_ENET_RESET	((ushort)0x0100)	/* PC  7 !!! */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
+ * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002E00)
+
 /* We don't use the 8259.
 */
 #define NR_8259_INTS	0
 
+#endif /* !__ASSEMBLY__ */
 #endif /* __ASM_SPD8XX_H__ */
 #endif /* __KERNEL__ */

arch/ppc/platforms/tqm8xx.h

@@ -7,6 +7,7 @@
  * Copyright (c) 1999,2000,2001 Wolfgang Denk (wd@denx.de)
  */
 
+#ifdef __KERNEL__
 #ifndef __MACH_TQM8xx_H
 #define __MACH_TQM8xx_H
 
@@ -14,6 +15,7 @@
  
 #include <asm/ppcboot.h>
 
+#ifndef __ASSEMBLY__
 #define	TQM_IMMR_BASE	0xFFF00000	/* phys. addr of IMMR */
 #define	TQM_IMAP_SIZE	(64 * 1024)	/* size of mapped area */
 
@@ -47,8 +49,106 @@
 #define	IDE0_INTERRUPT			13
 
 
+/*-----------------------------------------------------------------------
+ * CPM Ethernet through SCCx.
+ *-----------------------------------------------------------------------
+ *
+ */
+
+/***  TQM823L, TQM850L  ***********************************************/
+
+#if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
+#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
+#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
+
+#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
+#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002600)
+#endif	/* CONFIG_TQM823L, CONFIG_TQM850L */
+
+/***  TQM860L  ********************************************************/
+
+#ifdef CONFIG_TQM860L
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PA_ENET_RXD	((ushort)0x0001)	/* PA 15 */
+#define PA_ENET_TXD	((ushort)0x0002)	/* PA 14 */
+#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PC_ENET_TENA	((ushort)0x0001)	/* PC 15 */
+#define PC_ENET_CLSN	((ushort)0x0010)	/* PC 11 */
+#define PC_ENET_RENA	((ushort)0x0020)	/* PC 10 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x000000ff)
+#define SICR_ENET_CLKRT	((uint)0x00000026)
+#endif	/* CONFIG_TQM860L */
+
+/***  FPS850L  *********************************************************/
+
+#ifdef CONFIG_FPS850L
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
+#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
+#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PC_ENET_TENA	((ushort)0x0002)	/* PC 14 */
+#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
+#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+
+/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
+ * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002600)
+#endif	/* CONFIG_FPS850L */
+
+/***  SM850  *********************************************************/
+
+/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
+
+#ifdef CONFIG_SM850
+#define PB_ENET_RXD	((uint)0x00000004)	/* PB 29 */
+#define PB_ENET_TXD	((uint)0x00000002)	/* PB 30 */
+#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PC_ENET_LBK	((ushort)0x0008)	/* PC 12 */
+#define PC_ENET_TENA	((ushort)0x0004)	/* PC 13 */
+
+#define PC_ENET_RENA	((ushort)0x0800)	/* PC  4 */
+#define PC_ENET_CLSN	((ushort)0x0400)	/* PC  5 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC3.  Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x00FF0000)
+#define SICR_ENET_CLKRT	((uint)0x00260000)
+#endif	/* CONFIG_SM850 */
+
 /* We don't use the 8259.
 */
 #define NR_8259_INTS	0
 
+#endif /* !__ASSEMBLY__ */
 #endif	/* __MACH_TQM8xx_H */
+#endif /* __KERNEL__ */

include/asm-ppc/commproc.h

@@ -382,213 +382,6 @@ typedef struct scc_enet {
 	ushort	sen_taddrl;	/* temp address (LSB) */
 } scc_enet_t;
 
-/***  MBX  ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.  The TCLK and RCLK seem unique
- * to the MBX860 board.  Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PC_ENET_TENA	((ushort)0x0001)
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000003d)
-#endif	/* CONFIG_MBX */
-
-/***  RPXLITE  ********************************************************/
-
-#ifdef CONFIG_RPXLITE
-/* This ENET stuff is for the MPC850 with ethernet on SCC2.  Some of
- * this may be unique to the RPX-Lite configuration.
- * Note TENA is on Port B.
- */
-#define PA_ENET_RXD	((ushort)0x0004)
-#define PA_ENET_TXD	((ushort)0x0008)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PB_ENET_TENA	((uint)0x00002000)
-#define PC_ENET_CLSN	((ushort)0x0040)
-#define PC_ENET_RENA	((ushort)0x0080)
-
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00003d00)
-#endif	/* CONFIG_RPXLITE */
-
-/***  BSEIP  **********************************************************/
-
-#ifdef CONFIG_BSEIP
-/* This ENET stuff is for the MPC823 with ethernet on SCC2.
- * This is unique to the BSE ip-Engine board.
- */
-#define PA_ENET_RXD	((ushort)0x0004)
-#define PA_ENET_TXD	((ushort)0x0008)
-#define PA_ENET_TCLK	((ushort)0x0100)
-#define PA_ENET_RCLK	((ushort)0x0200)
-#define PB_ENET_TENA	((uint)0x00002000)
-#define PC_ENET_CLSN	((ushort)0x0040)
-#define PC_ENET_RENA	((ushort)0x0080)
-
-/* BSE uses port B and C bits for PHY control also.
-*/
-#define PB_BSE_POWERUP	((uint)0x00000004)
-#define PB_BSE_FDXDIS	((uint)0x00008000)
-#define PC_BSE_LOOPBACK	((ushort)0x0800)
-
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002c00)
-#endif	/* CONFIG_BSEIP */
-
-/***  RPXCLASSIC  *****************************************************/
-
-#ifdef CONFIG_RPXCLASSIC
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PB_ENET_TENA	((uint)0x00001000)
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000003d)
-#endif	/* CONFIG_RPXCLASSIC */
-
-/***  TQM823L, TQM850L  ***********************************************/
-
-#if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
-#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
-#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
-#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
-
-#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
-
-#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
-#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002600)
-#endif	/* CONFIG_TQM823L, CONFIG_TQM850L */
-
-/***  FPS850L  *********************************************************/
-
-#ifdef CONFIG_FPS850L
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
-#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
-#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
-#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
-
-#define PC_ENET_TENA	((ushort)0x0002)	/* PC 14 */
-#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
-#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002600)
-#endif	/* CONFIG_FPS850L */
-
-/***  TQM860L  ********************************************************/
-
-#ifdef CONFIG_TQM860L
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD	((ushort)0x0001)	/* PA 15 */
-#define PA_ENET_TXD	((ushort)0x0002)	/* PA 14 */
-#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
-#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
-
-#define PC_ENET_TENA	((ushort)0x0001)	/* PC 15 */
-#define PC_ENET_CLSN	((ushort)0x0010)	/* PC 11 */
-#define PC_ENET_RENA	((ushort)0x0020)	/* PC 10 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x00000026)
-#endif	/* CONFIG_TQM860L */
-
-/***  SPD823TS  *******************************************************/
-
-#ifdef CONFIG_SPD823TS
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PA_ENET_MDC	((ushort)0x0001)	/* PA 15 !!! */
-#define PA_ENET_MDIO	((ushort)0x0002)	/* PA 14 !!! */
-#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
-#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
-#define PA_ENET_RCLK	((ushort)0x0200)	/* PA  6 */
-#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
-
-#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
-
-#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
-#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
-#define	PC_ENET_RESET	((ushort)0x0100)	/* PC  7 !!! */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
- * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002E00)
-#endif	/* CONFIG_SPD823TS */
-
-
-/***  SM850  *********************************************************/
-
-/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
-
-#ifdef CONFIG_SM850
-#define PB_ENET_RXD	((uint)0x00000004)	/* PB 29 */
-#define PB_ENET_TXD	((uint)0x00000002)	/* PB 30 */
-#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
-#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
-
-#define PC_ENET_LBK	((ushort)0x0008)	/* PC 12 */
-#define PC_ENET_TENA	((ushort)0x0004)	/* PC 13 */
-
-#define PC_ENET_RENA	((ushort)0x0800)	/* PC  4 */
-#define PC_ENET_CLSN	((ushort)0x0400)	/* PC  5 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC3.  Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x00FF0000)
-#define SICR_ENET_CLKRT	((uint)0x00260000)
-#endif	/* CONFIG_SM850 */
-
-/*********************************************************************/
-
 /* SCC Event register as used by Ethernet.
 */
 #define SCCE_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */