Merge remote-tracking branches 'regulator/topic/max8973',...

Merge remote-tracking branches 'regulator/topic/max8973', 'regulator/topic/max8997', 'regulator/topic/max8998', 'regulator/topic/mc13xxx', 'regulator/topic/pfuze100', 'regulator/topic/rc5t583' and 'regulator/topic/s2mps11' into regulator-next

Documentation/devicetree/bindings/mfd/s2mpa01.txt

+
+* Samsung S2MPA01 Voltage and Current Regulator
+
+The Samsung S2MPA01 is a multi-function device which includes high
+efficiency buck converters including Dual-Phase buck converter, various LDOs,
+and an RTC. It is interfaced to the host controller using an I2C interface.
+Each sub-block is addressed by the host system using different I2C slave
+addresses.
+
+Required properties:
+- compatible: Should be "samsung,s2mpa01-pmic".
+- reg: Specifies the I2C slave address of the PMIC block. It should be 0x66.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+  the interrupts from s2mpa01 are delivered to.
+- interrupts: An interrupt specifier for the sole interrupt generated by the
+  device.
+
+Optional nodes:
+- regulators: The regulators of s2mpa01 that have to be instantiated should be
+  included in a sub-node named 'regulators'. Regulator nodes and constraints
+  included in this sub-node use the standard regulator bindings which are
+  documented elsewhere.
+
+Properties for BUCK regulator nodes:
+- regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500
+  (default), 25000, or 50000. May be 0 for disabling the ramp delay on
+  BUCK{1,2,3,4}.
+
+ In the absence of the regulator-ramp-delay property, the default ramp
+ delay will be used.
+
+  NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set
+  for a particular group of BUCKs. So provide same regulator-ramp-delay=<value>.
+
+  The following BUCKs share ramp settings:
+  * 1 and 6
+  * 2 and 4
+  * 8, 9, and 10
+
+The following are the names of the regulators that the s2mpa01 PMIC block
+supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of s2mpa01.
+
+	- LDOn
+		  - valid values for n are 1 to 26
+		  - Example: LDO1, LD02, LDO26
+	- BUCKn
+		  - valid values for n are 1 to 10.
+		  - Example: BUCK1, BUCK2, BUCK9
+
+Example:
+
+	s2mpa01_pmic@66 {
+		compatible = "samsung,s2mpa01-pmic";
+		reg = <0x66>;
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ALIVE";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDDQ_MMC2";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-ramp-delay = <50000>;
+			};
+		};
+	};

Documentation/devicetree/bindings/mfd/s2mps11.txt

 
-* Samsung S2MPS11 Voltage and Current Regulator
+* Samsung S2MPS11 and S2MPS14 Voltage and Current Regulator
 
 The Samsung S2MPS11 is a multi-function device which includes voltage and
 current regulators, RTC, charger controller and other sub-blocks. It is
@@ -7,7 +7,7 @@ interfaced to the host controller using an I2C interface. Each sub-block is
 addressed by the host system using different I2C slave addresses.
 
 Required properties:
-- compatible: Should be "samsung,s2mps11-pmic".
+- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps14-pmic".
 - reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
 
 Optional properties:
@@ -59,10 +59,14 @@ supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
 as per the datasheet of s2mps11.
 
 	- LDOn
-		  - valid values for n are 1 to 38
+		  - valid values for n are:
+			- S2MPS11: 1 to 38
+			- S2MPS14: 1 to 25
 		  - Example: LDO1, LD02, LDO28
 	- BUCKn
-		  - valid values for n are 1 to 10.
+		  - valid values for n are:
+			- S2MPS11: 1 to 10
+			- S2MPS14: 1 to 5
 		  - Example: BUCK1, BUCK2, BUCK9
 
 Example:

Documentation/devicetree/bindings/regulator/pfuze100.txt

 PFUZE100 family of regulators
 
 Required properties:
-- compatible: "fsl,pfuze100"
+- compatible: "fsl,pfuze100" or "fsl,pfuze200"
 - reg: I2C slave address
 
 Required child node:
@@ -10,11 +10,14 @@ Required child node:
   Documentation/devicetree/bindings/regulator/regulator.txt.
 
   The valid names for regulators are:
+  --PFUZE100
   sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6
+  --PFUZE200
+  sw1ab,sw2,sw3a,sw3b,swbst,vsnvs,vrefddr,vgen1~vgen6
 
 Each regulator is defined using the standard binding for regulators.
 
-Example:
+Example 1: PFUZE100
 
 	pmic: pfuze100@08 {
 		compatible = "fsl,pfuze100";
@@ -113,3 +116,92 @@ Example:
 			};
 		};
 	};
+
+
+Example 2: PFUZE200
+
+	pmic: pfuze200@08 {
+		compatible = "fsl,pfuze200";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};

drivers/mfd/sec-core.c

@@ -26,7 +26,9 @@
 #include <linux/mfd/samsung/core.h>
 #include <linux/mfd/samsung/irq.h>
 #include <linux/mfd/samsung/rtc.h>
+#include <linux/mfd/samsung/s2mpa01.h>
 #include <linux/mfd/samsung/s2mps11.h>
+#include <linux/mfd/samsung/s2mps14.h>
 #include <linux/mfd/samsung/s5m8763.h>
 #include <linux/mfd/samsung/s5m8767.h>
 #include <linux/regmap.h>
@@ -69,18 +71,53 @@ static const struct mfd_cell s2mps11_devs[] = {
 	}
 };
 
+static const struct mfd_cell s2mps14_devs[] = {
+	{
+		.name = "s2mps14-pmic",
+	}, {
+		.name = "s2mps14-rtc",
+	}, {
+		.name = "s2mps14-clk",
+	}
+};
+
+static const struct mfd_cell s2mpa01_devs[] = {
+	{
+		.name = "s2mpa01-pmic",
+	},
+};
+
 #ifdef CONFIG_OF
 static struct of_device_id sec_dt_match[] = {
 	{	.compatible = "samsung,s5m8767-pmic",
 		.data = (void *)S5M8767X,
-	},
-	{	.compatible = "samsung,s2mps11-pmic",
+	}, {
+		.compatible = "samsung,s2mps11-pmic",
 		.data = (void *)S2MPS11X,
+	}, {
+		.compatible = "samsung,s2mps14-pmic",
+		.data = (void *)S2MPS14X,
+	}, {
+		.compatible = "samsung,s2mpa01-pmic",
+		.data = (void *)S2MPA01,
+	}, {
+		/* Sentinel */
 	},
-	{},
 };
 #endif
 
+static bool s2mpa01_volatile(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case S2MPA01_REG_INT1M:
+	case S2MPA01_REG_INT2M:
+	case S2MPA01_REG_INT3M:
+		return false;
+	default:
+		return true;
+	}
+}
+
 static bool s2mps11_volatile(struct device *dev, unsigned int reg)
 {
 	switch (reg) {
@@ -111,6 +148,15 @@ static const struct regmap_config sec_regmap_config = {
 	.val_bits = 8,
 };
 
+static const struct regmap_config s2mpa01_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = S2MPA01_REG_LDO_OVCB4,
+	.volatile_reg = s2mpa01_volatile,
+	.cache_type = REGCACHE_FLAT,
+};
+
 static const struct regmap_config s2mps11_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
@@ -120,6 +166,15 @@ static const struct regmap_config s2mps11_regmap_config = {
 	.cache_type = REGCACHE_FLAT,
 };
 
+static const struct regmap_config s2mps14_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = S2MPS14_REG_LDODSCH3,
+	.volatile_reg = s2mps11_volatile,
+	.cache_type = REGCACHE_FLAT,
+};
+
 static const struct regmap_config s5m8763_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
@@ -138,9 +193,18 @@ static const struct regmap_config s5m8767_regmap_config = {
 	.cache_type = REGCACHE_FLAT,
 };
 
-static const struct regmap_config sec_rtc_regmap_config = {
+static const struct regmap_config s5m_rtc_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = SEC_RTC_REG_MAX,
+};
+
+static const struct regmap_config s2mps14_rtc_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
+
+	.max_register = S2MPS_RTC_REG_MAX,
 };
 
 #ifdef CONFIG_OF
@@ -180,24 +244,24 @@ static struct sec_platform_data *sec_pmic_i2c_parse_dt_pdata(
 }
 #endif
 
-static inline int sec_i2c_get_driver_data(struct i2c_client *i2c,
+static inline unsigned long sec_i2c_get_driver_data(struct i2c_client *i2c,
 						const struct i2c_device_id *id)
 {
 #ifdef CONFIG_OF
 	if (i2c->dev.of_node) {
 		const struct of_device_id *match;
 		match = of_match_node(sec_dt_match, i2c->dev.of_node);
-		return (int)match->data;
+		return (unsigned long)match->data;
 	}
 #endif
-	return (int)id->driver_data;
+	return id->driver_data;
 }
 
 static int sec_pmic_probe(struct i2c_client *i2c,
 			    const struct i2c_device_id *id)
 {
 	struct sec_platform_data *pdata = dev_get_platdata(&i2c->dev);
-	const struct regmap_config *regmap;
+	const struct regmap_config *regmap, *regmap_rtc;
 	struct sec_pmic_dev *sec_pmic;
 	int ret;
 
@@ -229,17 +293,34 @@ static int sec_pmic_probe(struct i2c_client *i2c,
 	}
 
 	switch (sec_pmic->device_type) {
+	case S2MPA01:
+		regmap = &s2mpa01_regmap_config;
+		break;
 	case S2MPS11X:
 		regmap = &s2mps11_regmap_config;
+		/*
+		 * The rtc-s5m driver does not support S2MPS11 and there
+		 * is no mfd_cell for S2MPS11 RTC device.
+		 * However we must pass something to devm_regmap_init_i2c()
+		 * so use S5M-like regmap config even though it wouldn't work.
+		 */
+		regmap_rtc = &s5m_rtc_regmap_config;
+		break;
+	case S2MPS14X:
+		regmap = &s2mps14_regmap_config;
+		regmap_rtc = &s2mps14_rtc_regmap_config;
 		break;
 	case S5M8763X:
 		regmap = &s5m8763_regmap_config;
+		regmap_rtc = &s5m_rtc_regmap_config;
 		break;
 	case S5M8767X:
 		regmap = &s5m8767_regmap_config;
+		regmap_rtc = &s5m_rtc_regmap_config;
 		break;
 	default:
 		regmap = &sec_regmap_config;
+		regmap_rtc = &s5m_rtc_regmap_config;
 		break;
 	}
 
@@ -252,10 +333,13 @@ static int sec_pmic_probe(struct i2c_client *i2c,
 	}
 
 	sec_pmic->rtc = i2c_new_dummy(i2c->adapter, RTC_I2C_ADDR);
+	if (!sec_pmic->rtc) {
+		dev_err(&i2c->dev, "Failed to allocate I2C for RTC\n");
+		return -ENODEV;
+	}
 	i2c_set_clientdata(sec_pmic->rtc, sec_pmic);
 
-	sec_pmic->regmap_rtc = devm_regmap_init_i2c(sec_pmic->rtc,
-			&sec_rtc_regmap_config);
+	sec_pmic->regmap_rtc = devm_regmap_init_i2c(sec_pmic->rtc, regmap_rtc);
 	if (IS_ERR(sec_pmic->regmap_rtc)) {
 		ret = PTR_ERR(sec_pmic->regmap_rtc);
 		dev_err(&i2c->dev, "Failed to allocate RTC register map: %d\n",
@@ -283,10 +367,18 @@ static int sec_pmic_probe(struct i2c_client *i2c,
 		ret = mfd_add_devices(sec_pmic->dev, -1, s5m8767_devs,
 				      ARRAY_SIZE(s5m8767_devs), NULL, 0, NULL);
 		break;
+	case S2MPA01:
+		ret = mfd_add_devices(sec_pmic->dev, -1, s2mpa01_devs,
+				      ARRAY_SIZE(s2mpa01_devs), NULL, 0, NULL);
+		break;
 	case S2MPS11X:
 		ret = mfd_add_devices(sec_pmic->dev, -1, s2mps11_devs,
 				      ARRAY_SIZE(s2mps11_devs), NULL, 0, NULL);
 		break;
+	case S2MPS14X:
+		ret = mfd_add_devices(sec_pmic->dev, -1, s2mps14_devs,
+				      ARRAY_SIZE(s2mps14_devs), NULL, 0, NULL);
+		break;
 	default:
 		/* If this happens the probe function is problem */
 		BUG();

drivers/mfd/sec-irq.c

 /*
  * sec-irq.c
  *
- * Copyright (c) 2011 Samsung Electronics Co., Ltd
+ * Copyright (c) 2011-2014 Samsung Electronics Co., Ltd
  *              http://www.samsung.com
  *
  *  This program is free software; you can redistribute  it and/or modify it
@@ -19,6 +19,7 @@
 #include <linux/mfd/samsung/core.h>
 #include <linux/mfd/samsung/irq.h>
 #include <linux/mfd/samsung/s2mps11.h>
+#include <linux/mfd/samsung/s2mps14.h>
 #include <linux/mfd/samsung/s5m8763.h>
 #include <linux/mfd/samsung/s5m8767.h>
 
@@ -59,13 +60,13 @@ static const struct regmap_irq s2mps11_irqs[] = {
 		.reg_offset = 1,
 		.mask = S2MPS11_IRQ_RTC60S_MASK,
 	},
-	[S2MPS11_IRQ_RTCA1] = {
+	[S2MPS11_IRQ_RTCA0] = {
 		.reg_offset = 1,
-		.mask = S2MPS11_IRQ_RTCA1_MASK,
+		.mask = S2MPS11_IRQ_RTCA0_MASK,
 	},
-	[S2MPS11_IRQ_RTCA2] = {
+	[S2MPS11_IRQ_RTCA1] = {
 		.reg_offset = 1,
-		.mask = S2MPS11_IRQ_RTCA2_MASK,
+		.mask = S2MPS11_IRQ_RTCA1_MASK,
 	},
 	[S2MPS11_IRQ_SMPL] = {
 		.reg_offset = 1,
@@ -89,6 +90,76 @@ static const struct regmap_irq s2mps11_irqs[] = {
 	},
 };
 
+static const struct regmap_irq s2mps14_irqs[] = {
+	[S2MPS14_IRQ_PWRONF] = {
+		.reg_offset = 0,
+		.mask = S2MPS11_IRQ_PWRONF_MASK,
+	},
+	[S2MPS14_IRQ_PWRONR] = {
+		.reg_offset = 0,
+		.mask = S2MPS11_IRQ_PWRONR_MASK,
+	},
+	[S2MPS14_IRQ_JIGONBF] = {
+		.reg_offset = 0,
+		.mask = S2MPS11_IRQ_JIGONBF_MASK,
+	},
+	[S2MPS14_IRQ_JIGONBR] = {
+		.reg_offset = 0,
+		.mask = S2MPS11_IRQ_JIGONBR_MASK,
+	},
+	[S2MPS14_IRQ_ACOKBF] = {
+		.reg_offset = 0,
+		.mask = S2MPS11_IRQ_ACOKBF_MASK,
+	},
+	[S2MPS14_IRQ_ACOKBR] = {
+		.reg_offset = 0,
+		.mask = S2MPS11_IRQ_ACOKBR_MASK,
+	},
+	[S2MPS14_IRQ_PWRON1S] = {
+		.reg_offset = 0,
+		.mask = S2MPS11_IRQ_PWRON1S_MASK,
+	},
+	[S2MPS14_IRQ_MRB] = {
+		.reg_offset = 0,
+		.mask = S2MPS11_IRQ_MRB_MASK,
+	},
+	[S2MPS14_IRQ_RTC60S] = {
+		.reg_offset = 1,
+		.mask = S2MPS11_IRQ_RTC60S_MASK,
+	},
+	[S2MPS14_IRQ_RTCA1] = {
+		.reg_offset = 1,
+		.mask = S2MPS11_IRQ_RTCA1_MASK,
+	},
+	[S2MPS14_IRQ_RTCA0] = {
+		.reg_offset = 1,
+		.mask = S2MPS11_IRQ_RTCA0_MASK,
+	},
+	[S2MPS14_IRQ_SMPL] = {
+		.reg_offset = 1,
+		.mask = S2MPS11_IRQ_SMPL_MASK,
+	},
+	[S2MPS14_IRQ_RTC1S] = {
+		.reg_offset = 1,
+		.mask = S2MPS11_IRQ_RTC1S_MASK,
+	},
+	[S2MPS14_IRQ_WTSR] = {
+		.reg_offset = 1,
+		.mask = S2MPS11_IRQ_WTSR_MASK,
+	},
+	[S2MPS14_IRQ_INT120C] = {
+		.reg_offset = 2,
+		.mask = S2MPS11_IRQ_INT120C_MASK,
+	},
+	[S2MPS14_IRQ_INT140C] = {
+		.reg_offset = 2,
+		.mask = S2MPS11_IRQ_INT140C_MASK,
+	},
+	[S2MPS14_IRQ_TSD] = {
+		.reg_offset = 2,
+		.mask = S2MPS14_IRQ_TSD_MASK,
+	},
+};
 
 static const struct regmap_irq s5m8767_irqs[] = {
 	[S5M8767_IRQ_PWRR] = {
@@ -246,6 +317,16 @@ static const struct regmap_irq_chip s2mps11_irq_chip = {
 	.ack_base = S2MPS11_REG_INT1,
 };
 
+static const struct regmap_irq_chip s2mps14_irq_chip = {
+	.name = "s2mps14",
+	.irqs = s2mps14_irqs,
+	.num_irqs = ARRAY_SIZE(s2mps14_irqs),
+	.num_regs = 3,
+	.status_base = S2MPS14_REG_INT1,
+	.mask_base = S2MPS14_REG_INT1M,
+	.ack_base = S2MPS14_REG_INT1,
+};
+
 static const struct regmap_irq_chip s5m8767_irq_chip = {
 	.name = "s5m8767",
 	.irqs = s5m8767_irqs,
@@ -297,6 +378,12 @@ int sec_irq_init(struct sec_pmic_dev *sec_pmic)
 				  sec_pmic->irq_base, &s2mps11_irq_chip,
 				  &sec_pmic->irq_data);
 		break;
+	case S2MPS14X:
+		ret = regmap_add_irq_chip(sec_pmic->regmap_pmic, sec_pmic->irq,
+				  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+				  sec_pmic->irq_base, &s2mps14_irq_chip,
+				  &sec_pmic->irq_data);
+		break;
 	default:
 		dev_err(sec_pmic->dev, "Unknown device type %d\n",
 			sec_pmic->device_type);

drivers/regulator/Kconfig

@@ -407,12 +407,12 @@ config REGULATOR_PCF50633
 	 on PCF50633
 
 config REGULATOR_PFUZE100
-	tristate "Freescale PFUZE100 regulator driver"
+	tristate "Freescale PFUZE100/PFUZE200 regulator driver"
 	depends on I2C
 	select REGMAP_I2C
 	help
-	  Say y here to support the regulators found on the Freescale PFUZE100
-	  PMIC.
+	  Say y here to support the regulators found on the Freescale
+	  PFUZE100/PFUZE200 PMIC.
 
 config REGULATOR_RC5T583
 	tristate "RICOH RC5T583 Power regulators"
@@ -424,13 +424,21 @@ config REGULATOR_RC5T583
 	  through regulator interface. The device supports multiple DCDC/LDO
 	  outputs which can be controlled by i2c communication.
 
+config REGULATOR_S2MPA01
+	tristate "Samsung S2MPA01 voltage regulator"
+	depends on MFD_SEC_CORE
+	help
+	 This driver controls Samsung S2MPA01 voltage output regulator
+	 via I2C bus. S2MPA01 has 10 Bucks and 26 LDO outputs.
+
 config REGULATOR_S2MPS11
-	tristate "Samsung S2MPS11 voltage regulator"
+	tristate "Samsung S2MPS11/S2MPS14 voltage regulator"
 	depends on MFD_SEC_CORE
 	help
-	 This driver supports a Samsung S2MPS11 voltage output regulator
-	 via I2C bus. S2MPS11 is comprised of high efficient Buck converters
-	 including Dual-Phase Buck converter, Buck-Boost converter, various LDOs.
+	 This driver supports a Samsung S2MPS11/S2MPS14 voltage output
+	 regulator via I2C bus. The chip is comprised of high efficient Buck
+	 converters including Dual-Phase Buck converter, Buck-Boost converter,
+	 various LDOs.
 
 config REGULATOR_S5M8767
 	tristate "Samsung S5M8767A voltage regulator"

drivers/regulator/Makefile

@@ -58,6 +58,7 @@ obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o
 obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o
 obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o
 obj-$(CONFIG_REGULATOR_RC5T583)  += rc5t583-regulator.o
+obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
 obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
 obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
 obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o

drivers/regulator/max8973-regulator.c

@@ -93,7 +93,6 @@
 struct max8973_chip {
 	struct device *dev;
 	struct regulator_desc desc;
-	struct regulator_dev *rdev;
 	struct regmap *regmap;
 	bool enable_external_control;
 	int dvs_gpio;
@@ -379,10 +378,8 @@ static int max8973_probe(struct i2c_client *client,
 	}
 
 	max = devm_kzalloc(&client->dev, sizeof(*max), GFP_KERNEL);
-	if (!max) {
-		dev_err(&client->dev, "Memory allocation for max failed\n");
+	if (!max)
 		return -ENOMEM;
-	}
 
 	max->regmap = devm_regmap_init_i2c(client, &max8973_regmap_config);
 	if (IS_ERR(max->regmap)) {
@@ -474,7 +471,6 @@ static int max8973_probe(struct i2c_client *client,
 		return ret;
 	}
 
-	max->rdev = rdev;
 	return 0;
 }
 

drivers/regulator/max8997.c

@@ -38,7 +38,6 @@ struct max8997_data {
 	struct device *dev;
 	struct max8997_dev *iodev;
 	int num_regulators;
-	struct regulator_dev **rdev;
 	int ramp_delay; /* in mV/us */
 
 	bool buck1_gpiodvs;
@@ -924,7 +923,7 @@ static int max8997_pmic_dt_parse_pdata(struct platform_device *pdev,
 		return -ENODEV;
 	}
 
-	regulators_np = of_find_node_by_name(pmic_np, "regulators");
+	regulators_np = of_get_child_by_name(pmic_np, "regulators");
 	if (!regulators_np) {
 		dev_err(&pdev->dev, "could not find regulators sub-node\n");
 		return -EINVAL;
@@ -937,7 +936,6 @@ static int max8997_pmic_dt_parse_pdata(struct platform_device *pdev,
 				pdata->num_regulators, GFP_KERNEL);
 	if (!rdata) {
 		of_node_put(regulators_np);
-		dev_err(&pdev->dev, "could not allocate memory for regulator data\n");
 		return -ENOMEM;
 	}
 
@@ -1030,10 +1028,10 @@ static int max8997_pmic_probe(struct platform_device *pdev)
 	struct max8997_dev *iodev = dev_get_drvdata(pdev->dev.parent);
 	struct max8997_platform_data *pdata = iodev->pdata;
 	struct regulator_config config = { };
-	struct regulator_dev **rdev;
+	struct regulator_dev *rdev;
 	struct max8997_data *max8997;
 	struct i2c_client *i2c;
-	int i, ret, size, nr_dvs;
+	int i, ret, nr_dvs;
 	u8 max_buck1 = 0, max_buck2 = 0, max_buck5 = 0;
 
 	if (!pdata) {
@@ -1052,12 +1050,6 @@ static int max8997_pmic_probe(struct platform_device *pdev)
 	if (!max8997)
 		return -ENOMEM;
 
-	size = sizeof(struct regulator_dev *) * pdata->num_regulators;
-	max8997->rdev = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
-	if (!max8997->rdev)
-		return -ENOMEM;
-
-	rdev = max8997->rdev;
 	max8997->dev = &pdev->dev;
 	max8997->iodev = iodev;
 	max8997->num_regulators = pdata->num_regulators;
@@ -1205,12 +1197,12 @@ static int max8997_pmic_probe(struct platform_device *pdev)
 		config.driver_data = max8997;
 		config.of_node = pdata->regulators[i].reg_node;
 
-		rdev[i] = devm_regulator_register(&pdev->dev, &regulators[id],
-						  &config);
-		if (IS_ERR(rdev[i])) {
+		rdev = devm_regulator_register(&pdev->dev, &regulators[id],
+					       &config);
+		if (IS_ERR(rdev)) {
 			dev_err(max8997->dev, "regulator init failed for %d\n",
 					id);
-			return PTR_ERR(rdev[i]);
+			return PTR_ERR(rdev);
 		}
 	}
 

drivers/regulator/max8998.c

@@ -40,7 +40,6 @@ struct max8998_data {
 	struct device		*dev;
 	struct max8998_dev	*iodev;
 	int			num_regulators;
-	struct regulator_dev	**rdev;
 	u8                      buck1_vol[4]; /* voltages for selection */
 	u8                      buck2_vol[2];
 	unsigned int		buck1_idx; /* index to last changed voltage */
@@ -674,8 +673,10 @@ static int max8998_pmic_dt_parse_pdata(struct max8998_dev *iodev,
 
 	rdata = devm_kzalloc(iodev->dev, sizeof(*rdata) *
 				pdata->num_regulators, GFP_KERNEL);
-	if (!rdata)
+	if (!rdata) {
+		of_node_put(regulators_np);
 		return -ENOMEM;
+	}
 
 	pdata->regulators = rdata;
 	for (i = 0; i < ARRAY_SIZE(regulators); ++i) {
@@ -692,6 +693,9 @@ static int max8998_pmic_dt_parse_pdata(struct max8998_dev *iodev,
 	}
 	pdata->num_regulators = rdata - pdata->regulators;
 
+	of_node_put(reg_np);
+	of_node_put(regulators_np);
+
 	ret = max8998_pmic_dt_parse_dvs_gpio(iodev, pdata, pmic_np);
 	if (ret)
 		return -EINVAL;
@@ -741,10 +745,10 @@ static int max8998_pmic_probe(struct platform_device *pdev)
 	struct max8998_dev *iodev = dev_get_drvdata(pdev->dev.parent);
 	struct max8998_platform_data *pdata = iodev->pdata;
 	struct regulator_config config = { };
-	struct regulator_dev **rdev;
+	struct regulator_dev *rdev;
 	struct max8998_data *max8998;
 	struct i2c_client *i2c;
-	int i, ret, size;
+	int i, ret;
 	unsigned int v;
 
 	if (!pdata) {
@@ -763,12 +767,6 @@ static int max8998_pmic_probe(struct platform_device *pdev)
 	if (!max8998)
 		return -ENOMEM;
 
-	size = sizeof(struct regulator_dev *) * pdata->num_regulators;
-	max8998->rdev = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
-	if (!max8998->rdev)
-		return -ENOMEM;
-
-	rdev = max8998->rdev;
 	max8998->dev = &pdev->dev;
 	max8998->iodev = iodev;
 	max8998->num_regulators = pdata->num_regulators;
@@ -872,13 +870,12 @@ static int max8998_pmic_probe(struct platform_device *pdev)
 		config.init_data = pdata->regulators[i].initdata;
 		config.driver_data = max8998;
 
-		rdev[i] = devm_regulator_register(&pdev->dev,
-						  &regulators[index], &config);
-		if (IS_ERR(rdev[i])) {
-			ret = PTR_ERR(rdev[i]);
+		rdev = devm_regulator_register(&pdev->dev, &regulators[index],
+					       &config);
+		if (IS_ERR(rdev)) {
+			ret = PTR_ERR(rdev);
 			dev_err(max8998->dev, "regulator %s init failed (%d)\n",
 						regulators[index].name, ret);
-			rdev[i] = NULL;
 			return ret;
 		}
 	}

drivers/regulator/mc13xxx-regulator-core.c

@@ -167,8 +167,10 @@ int mc13xxx_get_num_regulators_dt(struct platform_device *pdev)
 	struct device_node *parent;
 	int num;
 
-	of_node_get(pdev->dev.parent->of_node);
-	parent = of_find_node_by_name(pdev->dev.parent->of_node, "regulators");
+	if (!pdev->dev.parent->of_node)
+		return -ENODEV;
+
+	parent = of_get_child_by_name(pdev->dev.parent->of_node, "regulators");
 	if (!parent)
 		return -ENODEV;
 
@@ -187,8 +189,10 @@ struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
 	struct device_node *parent, *child;
 	int i, parsed = 0;
 
-	of_node_get(pdev->dev.parent->of_node);
-	parent = of_find_node_by_name(pdev->dev.parent->of_node, "regulators");
+	if (!pdev->dev.parent->of_node)
+		return NULL;
+
+	parent = of_get_child_by_name(pdev->dev.parent->of_node, "regulators");
 	if (!parent)
 		return NULL;
 

drivers/regulator/rc5t583-regulator.c

@@ -119,7 +119,6 @@ static int rc5t583_regulator_probe(struct platform_device *pdev)
 {
 	struct rc5t583 *rc5t583 = dev_get_drvdata(pdev->dev.parent);
 	struct rc5t583_platform_data *pdata = dev_get_platdata(rc5t583->dev);
-	struct regulator_init_data *reg_data;
 	struct regulator_config config = { };
 	struct rc5t583_regulator *reg = NULL;
 	struct rc5t583_regulator *regs;
@@ -135,19 +134,11 @@ static int rc5t583_regulator_probe(struct platform_device *pdev)
 
 	regs = devm_kzalloc(&pdev->dev, RC5T583_REGULATOR_MAX *
 			sizeof(struct rc5t583_regulator), GFP_KERNEL);
-	if (!regs) {
-		dev_err(&pdev->dev, "Memory allocation failed exiting..\n");
+	if (!regs)
 		return -ENOMEM;
-	}
 
 
 	for (id = 0; id < RC5T583_REGULATOR_MAX; ++id) {
-		reg_data = pdata->reg_init_data[id];
-
-		/* No need to register if there is no regulator data */
-		if (!reg_data)
-			continue;
-
 		reg = &regs[id];
 		ri = &rc5t583_reg_info[id];
 		reg->reg_info = ri;
@@ -169,7 +160,7 @@ static int rc5t583_regulator_probe(struct platform_device *pdev)
 
 skip_ext_pwr_config:
 		config.dev = &pdev->dev;
-		config.init_data = reg_data;
+		config.init_data = pdata->reg_init_data[id];
 		config.driver_data = reg;
 		config.regmap = rc5t583->regmap;
 

include/linux/mfd/samsung/core.h

@@ -18,7 +18,9 @@ enum sec_device_type {
 	S5M8751X,
 	S5M8763X,
 	S5M8767X,
+	S2MPA01,
 	S2MPS11X,
+	S2MPS14X,
 };
 
 /**
@@ -50,7 +52,7 @@ struct sec_pmic_dev {
 	struct regmap_irq_chip_data *irq_data;
 
 	int ono;
-	int type;
+	unsigned long type;
 	bool wakeup;
 	bool wtsr_smpl;
 };
@@ -92,7 +94,7 @@ struct sec_platform_data {
 	int				buck3_default_idx;
 	int				buck4_default_idx;
 
-	int                             buck_ramp_delay;
+	int				buck_ramp_delay;
 
 	int				buck2_ramp_delay;
 	int				buck34_ramp_delay;
@@ -100,10 +102,15 @@ struct sec_platform_data {
 	int				buck16_ramp_delay;
 	int				buck7810_ramp_delay;
 	int				buck9_ramp_delay;
-
-	bool                            buck2_ramp_enable;
-	bool                            buck3_ramp_enable;
-	bool                            buck4_ramp_enable;
+	int				buck24_ramp_delay;
+	int				buck3_ramp_delay;
+	int				buck7_ramp_delay;
+	int				buck8910_ramp_delay;
+
+	bool				buck1_ramp_enable;
+	bool				buck2_ramp_enable;
+	bool				buck3_ramp_enable;
+	bool				buck4_ramp_enable;
 	bool				buck6_ramp_enable;
 
 	int				buck2_init;

include/linux/mfd/samsung/irq.h

@@ -13,6 +13,56 @@
 #ifndef __LINUX_MFD_SEC_IRQ_H
 #define __LINUX_MFD_SEC_IRQ_H
 
+enum s2mpa01_irq {
+	S2MPA01_IRQ_PWRONF,
+	S2MPA01_IRQ_PWRONR,
+	S2MPA01_IRQ_JIGONBF,
+	S2MPA01_IRQ_JIGONBR,
+	S2MPA01_IRQ_ACOKBF,
+	S2MPA01_IRQ_ACOKBR,
+	S2MPA01_IRQ_PWRON1S,
+	S2MPA01_IRQ_MRB,
+
+	S2MPA01_IRQ_RTC60S,
+	S2MPA01_IRQ_RTCA1,
+	S2MPA01_IRQ_RTCA0,
+	S2MPA01_IRQ_SMPL,
+	S2MPA01_IRQ_RTC1S,
+	S2MPA01_IRQ_WTSR,
+
+	S2MPA01_IRQ_INT120C,
+	S2MPA01_IRQ_INT140C,
+	S2MPA01_IRQ_LDO3_TSD,
+	S2MPA01_IRQ_B16_TSD,
+	S2MPA01_IRQ_B24_TSD,
+	S2MPA01_IRQ_B35_TSD,
+
+	S2MPA01_IRQ_NR,
+};
+
+#define S2MPA01_IRQ_PWRONF_MASK		(1 << 0)
+#define S2MPA01_IRQ_PWRONR_MASK		(1 << 1)
+#define S2MPA01_IRQ_JIGONBF_MASK	(1 << 2)
+#define S2MPA01_IRQ_JIGONBR_MASK	(1 << 3)
+#define S2MPA01_IRQ_ACOKBF_MASK		(1 << 4)
+#define S2MPA01_IRQ_ACOKBR_MASK		(1 << 5)
+#define S2MPA01_IRQ_PWRON1S_MASK	(1 << 6)
+#define S2MPA01_IRQ_MRB_MASK		(1 << 7)
+
+#define S2MPA01_IRQ_RTC60S_MASK		(1 << 0)
+#define S2MPA01_IRQ_RTCA1_MASK		(1 << 1)
+#define S2MPA01_IRQ_RTCA0_MASK		(1 << 2)
+#define S2MPA01_IRQ_SMPL_MASK		(1 << 3)
+#define S2MPA01_IRQ_RTC1S_MASK		(1 << 4)
+#define S2MPA01_IRQ_WTSR_MASK		(1 << 5)
+
+#define S2MPA01_IRQ_INT120C_MASK	(1 << 0)
+#define S2MPA01_IRQ_INT140C_MASK	(1 << 1)
+#define S2MPA01_IRQ_LDO3_TSD_MASK	(1 << 2)
+#define S2MPA01_IRQ_B16_TSD_MASK	(1 << 3)
+#define S2MPA01_IRQ_B24_TSD_MASK	(1 << 4)
+#define S2MPA01_IRQ_B35_TSD_MASK	(1 << 5)
+
 enum s2mps11_irq {
 	S2MPS11_IRQ_PWRONF,
 	S2MPS11_IRQ_PWRONR,
@@ -24,8 +74,8 @@ enum s2mps11_irq {
 	S2MPS11_IRQ_MRB,
 
 	S2MPS11_IRQ_RTC60S,
+	S2MPS11_IRQ_RTCA0,
 	S2MPS11_IRQ_RTCA1,
-	S2MPS11_IRQ_RTCA2,
 	S2MPS11_IRQ_SMPL,
 	S2MPS11_IRQ_RTC1S,
 	S2MPS11_IRQ_WTSR,
@@ -47,7 +97,7 @@ enum s2mps11_irq {
 
 #define S2MPS11_IRQ_RTC60S_MASK		(1 << 0)
 #define S2MPS11_IRQ_RTCA1_MASK		(1 << 1)
-#define S2MPS11_IRQ_RTCA2_MASK		(1 << 2)
+#define S2MPS11_IRQ_RTCA0_MASK		(1 << 2)
 #define S2MPS11_IRQ_SMPL_MASK		(1 << 3)
 #define S2MPS11_IRQ_RTC1S_MASK		(1 << 4)
 #define S2MPS11_IRQ_WTSR_MASK		(1 << 5)
@@ -55,6 +105,33 @@ enum s2mps11_irq {
 #define S2MPS11_IRQ_INT120C_MASK	(1 << 0)
 #define S2MPS11_IRQ_INT140C_MASK	(1 << 1)
 
+enum s2mps14_irq {
+	S2MPS14_IRQ_PWRONF,
+	S2MPS14_IRQ_PWRONR,
+	S2MPS14_IRQ_JIGONBF,
+	S2MPS14_IRQ_JIGONBR,
+	S2MPS14_IRQ_ACOKBF,
+	S2MPS14_IRQ_ACOKBR,
+	S2MPS14_IRQ_PWRON1S,
+	S2MPS14_IRQ_MRB,
+
+	S2MPS14_IRQ_RTC60S,
+	S2MPS14_IRQ_RTCA1,
+	S2MPS14_IRQ_RTCA0,
+	S2MPS14_IRQ_SMPL,
+	S2MPS14_IRQ_RTC1S,
+	S2MPS14_IRQ_WTSR,
+
+	S2MPS14_IRQ_INT120C,
+	S2MPS14_IRQ_INT140C,
+	S2MPS14_IRQ_TSD,
+
+	S2MPS14_IRQ_NR,
+};
+
+/* Masks for interrupts are the same as in s2mps11 */
+#define S2MPS14_IRQ_TSD_MASK		(1 << 2)
+
 enum s5m8767_irq {
 	S5M8767_IRQ_PWRR,
 	S5M8767_IRQ_PWRF,

include/linux/mfd/samsung/rtc.h

-/*  rtc.h
+/* rtc.h
  *
- * Copyright (c) 2011 Samsung Electronics Co., Ltd
+ * Copyright (c) 2011-2014 Samsung Electronics Co., Ltd
  *              http://www.samsung.com
  *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
  *
  */
 
@@ -43,6 +48,39 @@ enum sec_rtc_reg {
 	SEC_RTC_STATUS,
 	SEC_WTSR_SMPL_CNTL,
 	SEC_RTC_UDR_CON,
+
+	SEC_RTC_REG_MAX,
+};
+
+enum s2mps_rtc_reg {
+	S2MPS_RTC_CTRL,
+	S2MPS_WTSR_SMPL_CNTL,
+	S2MPS_RTC_UDR_CON,
+	S2MPS_RSVD,
+	S2MPS_RTC_SEC,
+	S2MPS_RTC_MIN,
+	S2MPS_RTC_HOUR,
+	S2MPS_RTC_WEEKDAY,
+	S2MPS_RTC_DATE,
+	S2MPS_RTC_MONTH,
+	S2MPS_RTC_YEAR,
+	S2MPS_ALARM0_SEC,
+	S2MPS_ALARM0_MIN,
+	S2MPS_ALARM0_HOUR,
+	S2MPS_ALARM0_WEEKDAY,
+	S2MPS_ALARM0_DATE,
+	S2MPS_ALARM0_MONTH,
+	S2MPS_ALARM0_YEAR,
+	S2MPS_ALARM1_SEC,
+	S2MPS_ALARM1_MIN,
+	S2MPS_ALARM1_HOUR,
+	S2MPS_ALARM1_WEEKDAY,
+	S2MPS_ALARM1_DATE,
+	S2MPS_ALARM1_MONTH,
+	S2MPS_ALARM1_YEAR,
+	S2MPS_OFFSRC,
+
+	S2MPS_RTC_REG_MAX,
 };
 
 #define RTC_I2C_ADDR		(0x0C >> 1)
@@ -54,6 +92,9 @@ enum sec_rtc_reg {
 #define ALARM1_STATUS		(1 << 2)
 #define UPDATE_AD		(1 << 0)
 
+#define S2MPS_ALARM0_STATUS	(1 << 2)
+#define S2MPS_ALARM1_STATUS	(1 << 1)
+
 /* RTC Control Register */
 #define BCD_EN_SHIFT		0
 #define BCD_EN_MASK		(1 << BCD_EN_SHIFT)
@@ -62,6 +103,10 @@ enum sec_rtc_reg {
 /* RTC Update Register1 */
 #define RTC_UDR_SHIFT		0
 #define RTC_UDR_MASK		(1 << RTC_UDR_SHIFT)
+#define S2MPS_RTC_WUDR_SHIFT	4
+#define S2MPS_RTC_WUDR_MASK	(1 << S2MPS_RTC_WUDR_SHIFT)
+#define S2MPS_RTC_RUDR_SHIFT	0
+#define S2MPS_RTC_RUDR_MASK	(1 << S2MPS_RTC_RUDR_SHIFT)
 #define RTC_TCON_SHIFT		1
 #define RTC_TCON_MASK		(1 << RTC_TCON_SHIFT)
 #define RTC_TIME_EN_SHIFT	3

include/linux/mfd/samsung/s2mpa01.h

+/*
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd
+ *		http://www.samsung.com
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#ifndef __LINUX_MFD_S2MPA01_H
+#define __LINUX_MFD_S2MPA01_H
+
+/* S2MPA01 registers */
+enum s2mpa01_reg {
+	S2MPA01_REG_ID,
+	S2MPA01_REG_INT1,
+	S2MPA01_REG_INT2,
+	S2MPA01_REG_INT3,
+	S2MPA01_REG_INT1M,
+	S2MPA01_REG_INT2M,
+	S2MPA01_REG_INT3M,
+	S2MPA01_REG_ST1,
+	S2MPA01_REG_ST2,
+	S2MPA01_REG_PWRONSRC,
+	S2MPA01_REG_OFFSRC,
+	S2MPA01_REG_RTC_BUF,
+	S2MPA01_REG_CTRL1,
+	S2MPA01_REG_ETC_TEST,
+	S2MPA01_REG_RSVD1,
+	S2MPA01_REG_BU_CHG,
+	S2MPA01_REG_RAMP1,
+	S2MPA01_REG_RAMP2,
+	S2MPA01_REG_LDO_DSCH1,
+	S2MPA01_REG_LDO_DSCH2,
+	S2MPA01_REG_LDO_DSCH3,
+	S2MPA01_REG_LDO_DSCH4,
+	S2MPA01_REG_OTP_ADRL,
+	S2MPA01_REG_OTP_ADRH,
+	S2MPA01_REG_OTP_DATA,
+	S2MPA01_REG_MON1SEL,
+	S2MPA01_REG_MON2SEL,
+	S2MPA01_REG_LEE,
+	S2MPA01_REG_RSVD2,
+	S2MPA01_REG_RSVD3,
+	S2MPA01_REG_RSVD4,
+	S2MPA01_REG_RSVD5,
+	S2MPA01_REG_RSVD6,
+	S2MPA01_REG_TOP_RSVD,
+	S2MPA01_REG_DVS_SEL,
+	S2MPA01_REG_DVS_PTR,
+	S2MPA01_REG_DVS_DATA,
+	S2MPA01_REG_RSVD_NO,
+	S2MPA01_REG_UVLO,
+	S2MPA01_REG_LEE_NO,
+	S2MPA01_REG_B1CTRL1,
+	S2MPA01_REG_B1CTRL2,
+	S2MPA01_REG_B2CTRL1,
+	S2MPA01_REG_B2CTRL2,
+	S2MPA01_REG_B3CTRL1,
+	S2MPA01_REG_B3CTRL2,
+	S2MPA01_REG_B4CTRL1,
+	S2MPA01_REG_B4CTRL2,
+	S2MPA01_REG_B5CTRL1,
+	S2MPA01_REG_B5CTRL2,
+	S2MPA01_REG_B5CTRL3,
+	S2MPA01_REG_B5CTRL4,
+	S2MPA01_REG_B5CTRL5,
+	S2MPA01_REG_B5CTRL6,
+	S2MPA01_REG_B6CTRL1,
+	S2MPA01_REG_B6CTRL2,
+	S2MPA01_REG_B7CTRL1,
+	S2MPA01_REG_B7CTRL2,
+	S2MPA01_REG_B8CTRL1,
+	S2MPA01_REG_B8CTRL2,
+	S2MPA01_REG_B9CTRL1,
+	S2MPA01_REG_B9CTRL2,
+	S2MPA01_REG_B10CTRL1,
+	S2MPA01_REG_B10CTRL2,
+	S2MPA01_REG_L1CTRL,
+	S2MPA01_REG_L2CTRL,
+	S2MPA01_REG_L3CTRL,
+	S2MPA01_REG_L4CTRL,
+	S2MPA01_REG_L5CTRL,
+	S2MPA01_REG_L6CTRL,
+	S2MPA01_REG_L7CTRL,
+	S2MPA01_REG_L8CTRL,
+	S2MPA01_REG_L9CTRL,
+	S2MPA01_REG_L10CTRL,
+	S2MPA01_REG_L11CTRL,
+	S2MPA01_REG_L12CTRL,
+	S2MPA01_REG_L13CTRL,
+	S2MPA01_REG_L14CTRL,
+	S2MPA01_REG_L15CTRL,
+	S2MPA01_REG_L16CTRL,
+	S2MPA01_REG_L17CTRL,
+	S2MPA01_REG_L18CTRL,
+	S2MPA01_REG_L19CTRL,
+	S2MPA01_REG_L20CTRL,
+	S2MPA01_REG_L21CTRL,
+	S2MPA01_REG_L22CTRL,
+	S2MPA01_REG_L23CTRL,
+	S2MPA01_REG_L24CTRL,
+	S2MPA01_REG_L25CTRL,
+	S2MPA01_REG_L26CTRL,
+
+	S2MPA01_REG_LDO_OVCB1,
+	S2MPA01_REG_LDO_OVCB2,
+	S2MPA01_REG_LDO_OVCB3,
+	S2MPA01_REG_LDO_OVCB4,
+
+};
+
+/* S2MPA01 regulator ids */
+enum s2mpa01_regulators {
+	S2MPA01_LDO1,
+	S2MPA01_LDO2,
+	S2MPA01_LDO3,
+	S2MPA01_LDO4,
+	S2MPA01_LDO5,
+	S2MPA01_LDO6,
+	S2MPA01_LDO7,
+	S2MPA01_LDO8,
+	S2MPA01_LDO9,
+	S2MPA01_LDO10,
+	S2MPA01_LDO11,
+	S2MPA01_LDO12,
+	S2MPA01_LDO13,
+	S2MPA01_LDO14,
+	S2MPA01_LDO15,
+	S2MPA01_LDO16,
+	S2MPA01_LDO17,
+	S2MPA01_LDO18,
+	S2MPA01_LDO19,
+	S2MPA01_LDO20,
+	S2MPA01_LDO21,
+	S2MPA01_LDO22,
+	S2MPA01_LDO23,
+	S2MPA01_LDO24,
+	S2MPA01_LDO25,
+	S2MPA01_LDO26,
+
+	S2MPA01_BUCK1,
+	S2MPA01_BUCK2,
+	S2MPA01_BUCK3,
+	S2MPA01_BUCK4,
+	S2MPA01_BUCK5,
+	S2MPA01_BUCK6,
+	S2MPA01_BUCK7,
+	S2MPA01_BUCK8,
+	S2MPA01_BUCK9,
+	S2MPA01_BUCK10,
+
+	S2MPA01_REGULATOR_MAX,
+};
+
+#define S2MPA01_BUCK_MIN1	600000
+#define S2MPA01_BUCK_MIN2	800000
+#define S2MPA01_BUCK_MIN3	1000000
+#define S2MPA01_BUCK_MIN4	1500000
+#define S2MPA01_LDO_MIN		800000
+
+#define S2MPA01_BUCK_STEP1	6250
+#define S2MPA01_BUCK_STEP2	12500
+
+#define S2MPA01_LDO_STEP1	50000
+#define S2MPA01_LDO_STEP2	25000
+
+#define S2MPA01_LDO_VSEL_MASK	0x3F
+#define S2MPA01_BUCK_VSEL_MASK	0xFF
+#define S2MPA01_ENABLE_MASK	(0x03 << S2MPA01_ENABLE_SHIFT)
+#define S2MPA01_ENABLE_SHIFT	0x06
+#define S2MPA01_LDO_N_VOLTAGES	(S2MPA01_LDO_VSEL_MASK + 1)
+#define S2MPA01_BUCK_N_VOLTAGES (S2MPA01_BUCK_VSEL_MASK + 1)
+
+#define S2MPA01_RAMP_DELAY	12500	/* uV/us */
+
+#define S2MPA01_BUCK16_RAMP_SHIFT	4
+#define S2MPA01_BUCK24_RAMP_SHIFT	6
+#define S2MPA01_BUCK3_RAMP_SHIFT	4
+#define S2MPA01_BUCK5_RAMP_SHIFT	6
+#define S2MPA01_BUCK7_RAMP_SHIFT	2
+#define S2MPA01_BUCK8910_RAMP_SHIFT	0
+
+#define S2MPA01_BUCK1_RAMP_EN_SHIFT	3
+#define S2MPA01_BUCK2_RAMP_EN_SHIFT	2
+#define S2MPA01_BUCK3_RAMP_EN_SHIFT	1
+#define S2MPA01_BUCK4_RAMP_EN_SHIFT	0
+#define S2MPA01_PMIC_EN_SHIFT	6
+
+#endif /*__LINUX_MFD_S2MPA01_H */

include/linux/mfd/samsung/s2mps14.h

+/*
+ * s2mps14.h
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd
+ *              http://www.samsung.com
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __LINUX_MFD_S2MPS14_H
+#define __LINUX_MFD_S2MPS14_H
+
+/* S2MPS14 registers */
+enum s2mps14_reg {
+	S2MPS14_REG_ID,
+	S2MPS14_REG_INT1,
+	S2MPS14_REG_INT2,
+	S2MPS14_REG_INT3,
+	S2MPS14_REG_INT1M,
+	S2MPS14_REG_INT2M,
+	S2MPS14_REG_INT3M,
+	S2MPS14_REG_ST1,
+	S2MPS14_REG_ST2,
+	S2MPS14_REG_PWRONSRC,
+	S2MPS14_REG_OFFSRC,
+	S2MPS14_REG_BU_CHG,
+	S2MPS14_REG_RTCCTRL,
+	S2MPS14_REG_CTRL1,
+	S2MPS14_REG_CTRL2,
+	S2MPS14_REG_RSVD1,
+	S2MPS14_REG_RSVD2,
+	S2MPS14_REG_RSVD3,
+	S2MPS14_REG_RSVD4,
+	S2MPS14_REG_RSVD5,
+	S2MPS14_REG_RSVD6,
+	S2MPS14_REG_CTRL3,
+	S2MPS14_REG_RSVD7,
+	S2MPS14_REG_RSVD8,
+	S2MPS14_REG_WRSTBI,
+	S2MPS14_REG_B1CTRL1,
+	S2MPS14_REG_B1CTRL2,
+	S2MPS14_REG_B2CTRL1,
+	S2MPS14_REG_B2CTRL2,
+	S2MPS14_REG_B3CTRL1,
+	S2MPS14_REG_B3CTRL2,
+	S2MPS14_REG_B4CTRL1,
+	S2MPS14_REG_B4CTRL2,
+	S2MPS14_REG_B5CTRL1,
+	S2MPS14_REG_B5CTRL2,
+	S2MPS14_REG_L1CTRL,
+	S2MPS14_REG_L2CTRL,
+	S2MPS14_REG_L3CTRL,
+	S2MPS14_REG_L4CTRL,
+	S2MPS14_REG_L5CTRL,
+	S2MPS14_REG_L6CTRL,
+	S2MPS14_REG_L7CTRL,
+	S2MPS14_REG_L8CTRL,
+	S2MPS14_REG_L9CTRL,
+	S2MPS14_REG_L10CTRL,
+	S2MPS14_REG_L11CTRL,
+	S2MPS14_REG_L12CTRL,
+	S2MPS14_REG_L13CTRL,
+	S2MPS14_REG_L14CTRL,
+	S2MPS14_REG_L15CTRL,
+	S2MPS14_REG_L16CTRL,
+	S2MPS14_REG_L17CTRL,
+	S2MPS14_REG_L18CTRL,
+	S2MPS14_REG_L19CTRL,
+	S2MPS14_REG_L20CTRL,
+	S2MPS14_REG_L21CTRL,
+	S2MPS14_REG_L22CTRL,
+	S2MPS14_REG_L23CTRL,
+	S2MPS14_REG_L24CTRL,
+	S2MPS14_REG_L25CTRL,
+	S2MPS14_REG_LDODSCH1,
+	S2MPS14_REG_LDODSCH2,
+	S2MPS14_REG_LDODSCH3,
+};
+
+/* S2MPS14 regulator ids */
+enum s2mps14_regulators {
+	S2MPS14_LDO1,
+	S2MPS14_LDO2,
+	S2MPS14_LDO3,
+	S2MPS14_LDO4,
+	S2MPS14_LDO5,
+	S2MPS14_LDO6,
+	S2MPS14_LDO7,
+	S2MPS14_LDO8,
+	S2MPS14_LDO9,
+	S2MPS14_LDO10,
+	S2MPS14_LDO11,
+	S2MPS14_LDO12,
+	S2MPS14_LDO13,
+	S2MPS14_LDO14,
+	S2MPS14_LDO15,
+	S2MPS14_LDO16,
+	S2MPS14_LDO17,
+	S2MPS14_LDO18,
+	S2MPS14_LDO19,
+	S2MPS14_LDO20,
+	S2MPS14_LDO21,
+	S2MPS14_LDO22,
+	S2MPS14_LDO23,
+	S2MPS14_LDO24,
+	S2MPS14_LDO25,
+	S2MPS14_BUCK1,
+	S2MPS14_BUCK2,
+	S2MPS14_BUCK3,
+	S2MPS14_BUCK4,
+	S2MPS14_BUCK5,
+
+	S2MPS14_REGULATOR_MAX,
+};
+
+/* Regulator constraints for BUCKx */
+#define S2MPS14_BUCK1235_MIN_600MV	600000
+#define S2MPS14_BUCK4_MIN_1400MV	1400000
+#define S2MPS14_BUCK1235_STEP_6_25MV	6250
+#define S2MPS14_BUCK4_STEP_12_5MV	12500
+#define S2MPS14_BUCK1235_START_SEL	0x20
+#define S2MPS14_BUCK4_START_SEL		0x40
+/*
+ * Default ramp delay in uv/us. Datasheet says that ramp delay can be
+ * controlled however it does not specify which register is used for that.
+ * Let's assume that default value will be set.
+ */
+#define S2MPS14_BUCK_RAMP_DELAY		12500
+
+/* Regulator constraints for different types of LDOx */
+#define S2MPS14_LDO_MIN_800MV		800000
+#define S2MPS14_LDO_MIN_1800MV		1800000
+#define S2MPS14_LDO_STEP_12_5MV		12500
+#define S2MPS14_LDO_STEP_25MV		25000
+
+#define S2MPS14_LDO_VSEL_MASK		0x3F
+#define S2MPS14_BUCK_VSEL_MASK		0xFF
+#define S2MPS14_ENABLE_MASK		(0x03 << S2MPS14_ENABLE_SHIFT)
+#define S2MPS14_ENABLE_SHIFT		6
+/* On/Off controlled by PWREN */
+#define S2MPS14_ENABLE_SUSPEND		(0x01 << S2MPS14_ENABLE_SHIFT)
+#define S2MPS14_LDO_N_VOLTAGES		(S2MPS14_LDO_VSEL_MASK + 1)
+#define S2MPS14_BUCK_N_VOLTAGES		(S2MPS14_BUCK_VSEL_MASK + 1)
+
+#endif /*  __LINUX_MFD_S2MPS14_H */

include/linux/regulator/pfuze100.h

@@ -35,6 +35,20 @@
 #define PFUZE100_VGEN6		14
 #define PFUZE100_MAX_REGULATOR	15
 
+#define PFUZE200_SW1AB		0
+#define PFUZE200_SW2		1
+#define PFUZE200_SW3A		2
+#define PFUZE200_SW3B		3
+#define PFUZE200_SWBST		4
+#define PFUZE200_VSNVS		5
+#define PFUZE200_VREFDDR	6
+#define PFUZE200_VGEN1		7
+#define PFUZE200_VGEN2		8
+#define PFUZE200_VGEN3		9
+#define PFUZE200_VGEN4		10
+#define PFUZE200_VGEN5		11
+#define PFUZE200_VGEN6		12
+
 struct regulator_init_data;
 
 struct pfuze_regulator_platform_data {