Commit 7cdeb24d authored by Philipp Zabel's avatar Philipp Zabel

dt-bindings: drm/mediatek: Add Mediatek HDMI dts binding

Add the device tree binding documentation for Mediatek HDMI,
HDMI PHY and HDMI DDC devices.
Signed-off-by: default avatarPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: default avatarRob Herring <robh@kernel.org>
parent af8c34ce
Mediatek HDMI Encoder
=====================
The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
its parallel input.
Required properties:
- compatible: Should be "mediatek,<chip>-hdmi".
- reg: Physical base address and length of the controller's registers
- interrupts: The interrupt signal from the function block.
- clocks: device clocks
See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
- clock-names: must contain "pixel", "pll", "bclk", and "spdif".
- phys: phandle link to the HDMI PHY node.
See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
- phy-names: must contain "hdmi"
- mediatek,syscon-hdmi: phandle link and register offset to the system
configuration registers. For mt8173 this must be offset 0x900 into the
MMSYS_CONFIG region: <&mmsys 0x900>.
- ports: A node containing input and output port nodes with endpoint
definitions as documented in Documentation/devicetree/bindings/graph.txt.
- port@0: The input port in the ports node should be connected to a DPI output
port.
- port@1: The output port in the ports node should be connected to the input
port of a connector node that contains a ddc-i2c-bus property, or to the
input port of an attached bridge chip, such as a SlimPort transmitter.
HDMI CEC
========
The HDMI CEC controller handles hotplug detection and CEC communication.
Required properties:
- compatible: Should be "mediatek,<chip>-cec"
- reg: Physical base address and length of the controller's registers
- interrupts: The interrupt signal from the function block.
- clocks: device clock
HDMI DDC
========
The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
The Mediatek's I2C controller is used to interface with I2C devices.
Required properties:
- compatible: Should be "mediatek,<chip>-hdmi-ddc"
- reg: Physical base address and length of the controller's registers
- clocks: device clock
- clock-names: Should be "ddc-i2c".
HDMI PHY
========
The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
output and drives the HDMI pads.
Required properties:
- compatible: "mediatek,<chip>-hdmi-phy"
- reg: Physical base address and length of the module's registers
- clocks: PLL reference clock
- clock-names: must contain "pll_ref"
- clock-output-names: must be "hdmitx_dig_cts" on mt8173
- #phy-cells: must be <0>
- #clock-cells: must be <0>
Optional properties:
- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa
- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c
Example:
cec: cec@10013000 {
compatible = "mediatek,mt8173-cec";
reg = <0 0x10013000 0 0xbc>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
clocks = <&infracfg CLK_INFRA_CEC>;
};
hdmi_phy: hdmi-phy@10209100 {
compatible = "mediatek,mt8173-hdmi-phy";
reg = <0 0x10209100 0 0x24>;
clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
clock-names = "pll_ref";
clock-output-names = "hdmitx_dig_cts";
mediatek,ibias = <0xa>;
mediatek,ibias_up = <0x1c>;
#clock-cells = <0>;
#phy-cells = <0>;
};
hdmi_ddc0: i2c@11012000 {
compatible = "mediatek,mt8173-hdmi-ddc";
reg = <0 0x11012000 0 0x1c>;
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
clocks = <&pericfg CLK_PERI_I2C5>;
clock-names = "ddc-i2c";
};
hdmi0: hdmi@14025000 {
compatible = "mediatek,mt8173-hdmi";
reg = <0 0x14025000 0 0x400>;
interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
<&mmsys CLK_MM_HDMI_PLLCK>,
<&mmsys CLK_MM_HDMI_AUDIO>,
<&mmsys CLK_MM_HDMI_SPDIF>;
clock-names = "pixel", "pll", "bclk", "spdif";
pinctrl-names = "default";
pinctrl-0 = <&hdmi_pin>;
phys = <&hdmi_phy>;
phy-names = "hdmi";
mediatek,syscon-hdmi = <&mmsys 0x900>;
assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
assigned-clock-parents = <&hdmi_phy>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
hdmi0_in: endpoint {
remote-endpoint = <&dpi0_out>;
};
};
port@1 {
reg = <1>;
hdmi0_out: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
};
};
connector {
compatible = "hdmi-connector";
type = "a";
ddc-i2c-bus = <&hdmiddc0>;
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi0_out>;
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment