PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device characteristics

Per PCIe r3.1, sec 5.5.1, LTR_L1.2_THRESHOLD determines whether we enter
the L1.2 Link state: if L1.2 is enabled and downstream devices have
reported that they can tolerate latency of at least LTR_L1.2_THRESHOLD, we
must enter L1.2 when CLKREQ# is de-asserted.

The implication is that LTR_L1.2_THRESHOLD is the time required to
transition the Link from L0 to L1.2 and back to L0, and per sec 5.5.3.3.1,
Figures 5-16 and 5-17, it appears that the absolute minimum time for those
transitions would be T(POWER_OFF) + T(L1.2) + T(POWER_ON) + T(COMMONMODE).

Therefore, compute LTR_L1.2_THRESHOLD as:

    2us T(POWER_OFF)
  + 4us T(L1.2)
  + T(POWER_ON)
  + T(COMMONMODE)
  = LTR_L1.2_THRESHOLD

Previously we set LTR_L1.2_THRESHOLD to a fixed value of 163840ns
(163.84us):

  #define LTR_L1_2_THRESHOLD_BITS     ((1 << 21) | (1 << 23) | (1 << 30))
  ((1 << 21) | (1 << 23) | (1 << 30)) = 0x40a00000
  LTR_L1.2_THRESHOLD_Value = (0x40a00000 & 0x03ff0000) >> 16 = 0xa0 = 160
  LTR_L1.2_THRESHOLD_Scale = (0x40a00000 & 0xe0000000) >> 29 = 0x2 (* 1024ns)
  LTR_L1.2_THRESHOLD = 160 * 1024ns = 163840ns

Obviously this doesn't account for the circuit characteristics of different
implementations.

Note that while firmware may enable LTR, Linux itself currently does not
enable LTR.  When L1.2 is enabled but LTR is not, LTR_L1.2_THRESHOLD is
ignored and we always enter L1.2 when it is enabled and CLKREQ# is
de-asserted.  So this patch should not have any effect unless firmware
enables LTR.

Fixes: f1f0366d ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Link: https://www.coreboot.org/pipermail/coreboot-gerrit/2015-March/021134.htmlSigned-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Cc: Kenji Chen <kenji.chen@intel.com>
Cc: Patrick Georgi <pgeorgi@google.com>
Cc: Rajat Jain <rajatja@google.com>

drivers/pci/pcie/aspm.c

@@ -43,18 +43,6 @@
 #define ASPM_STATE_ALL		(ASPM_STATE_L0S | ASPM_STATE_L1 |	\
 				 ASPM_STATE_L1SS)
 
-/*
- * When L1 substates are enabled, the LTR L1.2 threshold is a timing parameter
- * that decides whether L1.1 or L1.2 is entered (Refer PCIe spec for details).
- * Not sure is there is a way to "calculate" this on the fly, but maybe we
- * could turn it into a parameter in future.  This value has been taken from
- * the following files from Intel's coreboot (which is the only code I found
- * to have used this):
- * https://www.coreboot.org/pipermail/coreboot-gerrit/2015-March/021134.html
- * https://review.coreboot.org/#/c/8832/
- */
-#define LTR_L1_2_THRESHOLD_BITS	((1 << 21) | (1 << 23) | (1 << 30))
-
 struct aspm_latency {
 	u32 l0s;			/* L0s latency (nsec) */
 	u32 l1;				/* L1 latency (nsec) */
@@ -333,6 +321,32 @@ static u32 calc_l1ss_pwron(struct pci_dev *pdev, u32 scale, u32 val)
 	return 0;
 }
 
+static void encode_l12_threshold(u32 threshold_us, u32 *scale, u32 *value)
+{
+	u64 threshold_ns = threshold_us * 1000;
+
+	/* See PCIe r3.1, sec 7.33.3 and sec 6.18 */
+	if (threshold_ns < 32) {
+		*scale = 0;
+		*value = threshold_ns;
+	} else if (threshold_ns < 1024) {
+		*scale = 1;
+		*value = threshold_ns >> 5;
+	} else if (threshold_ns < 32768) {
+		*scale = 2;
+		*value = threshold_ns >> 10;
+	} else if (threshold_ns < 1048576) {
+		*scale = 3;
+		*value = threshold_ns >> 15;
+	} else if (threshold_ns < 33554432) {
+		*scale = 4;
+		*value = threshold_ns >> 20;
+	} else {
+		*scale = 5;
+		*value = threshold_ns >> 25;
+	}
+}
+
 struct aspm_register_info {
 	u32 support:2;
 	u32 enabled:2;
@@ -443,6 +457,7 @@ static void aspm_calc_l1ss_info(struct pcie_link_state *link,
 				struct aspm_register_info *dwreg)
 {
 	u32 val1, val2, scale1, scale2;
+	u32 t_common_mode, t_power_on, l1_2_threshold, scale, value;
 
 	link->l1ss.up_cap_ptr = upreg->l1ss_cap_ptr;
 	link->l1ss.dw_cap_ptr = dwreg->l1ss_cap_ptr;
@@ -454,16 +469,7 @@ static void aspm_calc_l1ss_info(struct pcie_link_state *link,
 	/* Choose the greater of the two Port Common_Mode_Restore_Times */
 	val1 = (upreg->l1ss_cap & PCI_L1SS_CAP_CM_RESTORE_TIME) >> 8;
 	val2 = (dwreg->l1ss_cap & PCI_L1SS_CAP_CM_RESTORE_TIME) >> 8;
-	if (val1 > val2)
-		link->l1ss.ctl1 |= val1 << 8;
-	else
-		link->l1ss.ctl1 |= val2 << 8;
-
-	/*
-	 * We currently use LTR L1.2 threshold to be fixed constant picked from
-	 * Intel's coreboot.
-	 */
-	link->l1ss.ctl1 |= LTR_L1_2_THRESHOLD_BITS;
+	t_common_mode = max(val1, val2);
 
 	/* Choose the greater of the two Port T_POWER_ON times */
 	val1   = (upreg->l1ss_cap & PCI_L1SS_CAP_P_PWR_ON_VALUE) >> 19;
@@ -472,10 +478,27 @@ static void aspm_calc_l1ss_info(struct pcie_link_state *link,
 	scale2 = (dwreg->l1ss_cap & PCI_L1SS_CAP_P_PWR_ON_SCALE) >> 16;
 
 	if (calc_l1ss_pwron(link->pdev, scale1, val1) >
-	    calc_l1ss_pwron(link->downstream, scale2, val2))
+	    calc_l1ss_pwron(link->downstream, scale2, val2)) {
 		link->l1ss.ctl2 |= scale1 | (val1 << 3);
-	else
+		t_power_on = calc_l1ss_pwron(link->pdev, scale1, val1);
+	} else {
 		link->l1ss.ctl2 |= scale2 | (val2 << 3);
+		t_power_on = calc_l1ss_pwron(link->downstream, scale2, val2);
+	}
+
+	/*
+	 * Set LTR_L1.2_THRESHOLD to the time required to transition the
+	 * Link from L0 to L1.2 and back to L0 so we enter L1.2 only if
+	 * downstream devices report (via LTR) that they can tolerate at
+	 * least that much latency.
+	 *
+	 * Based on PCIe r3.1, sec 5.5.3.3.1, Figures 5-16 and 5-17, and
+	 * Table 5-11.  T(POWER_OFF) is at most 2us and T(L1.2) is at
+	 * least 4us.
+	 */
+	l1_2_threshold = 2 + 4 + t_common_mode + t_power_on;
+	encode_l12_threshold(l1_2_threshold, &scale, &value);
+	link->l1ss.ctl1 |= t_common_mode << 8 | scale << 29 | value << 16;
 }
 
 static void pcie_aspm_cap_init(struct pcie_link_state *link, int blacklist)