Commit 811a4f6d authored by Mauro Carvalho Chehab's avatar Mauro Carvalho Chehab

[media] siano: Fix initialization for Stellar models

Since kernel 3.8, the initialization for Stellar (sms1000)
devices are broken.
Those devices have a behaviour different than usual sms1100
and sms2270: they start with one USB ID (devices in cold state),
but after firmware load, they get a different USB ID.
This weren't docummented at the driver. So, the patches that added
support for sms2270 broke it.
Properly documment it, and provide a debug log that allows to
follow all phases of the device initialization:
	smsusb_probe: board id=13, interface number 0
	smsusb_probe: interface 0 won't be used. Expecting interface 1 to popup
	smsusb_probe: board id=13, interface number 1
	smsusb_probe: smsusb_probe 1
	smsusb_probe: endpoint 0 81 02 64
	smsusb_probe: endpoint 1 02 02 64
	smsusb_probe: stellar device in cold state was found at usb\4-2.
	smsusb1_load_firmware: sent 38144(38144) bytes, rc 0
	smsusb1_load_firmware: read FW dvbt_bda_stellar_usb.inp, size=38144
	smsusb_probe: stellar device now in warm state
	usbcore: registered new interface driver smsusb
	usb 4-2: USB disconnect, device number 52
	usb 4-2: new full-speed USB device number 53 using uhci_hcd
	usb 4-2: New USB device found, idVendor=187f, idProduct=0100
	usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
	usb 4-2: Product: SMS DVBT-BDA Receiver
	usb 4-2: Manufacturer: Siano Mobile Silicon
	smsusb_probe: board id=1, interface number 0
	smsusb_probe: smsusb_probe 0
	smsusb_probe: endpoint 0 81 02 64
	smsusb_probe: endpoint 1 02 02 64
	smsusb_init_device: in_ep = 81, out_ep = 02
	smscore_register_device: allocated 50 buffers
	smscore_register_device: device ffff88012a00bc00 created
	smsusb_init_device: smsusb_start_streaming(...).
	smscore_set_device_mode: set device mode to 4
	smsusb1_detectmode: 4 "SMS DVBT-BDA Receiver"
	smsusb_sendrequest: sending MSG_SMS_INIT_DEVICE_REQ(578) size: 12
	smsusb_onresponse: received MSG_SMS_INIT_DEVICE_RES(579) size: 12
	smscore_set_device_mode: Success setting device mode.
	smscore_init_ir: IR port has not been detected
	smscore_start_device: device ffff88012a00bc00 started, rc 0
	smsusb_init_device: device 0xffff88002cfa6000 created
	smsusb_probe: Device initialized with return code 0
	DVB: registering new adapter (Siano Stellar Digital Receiver)
	usb 4-2: DVB: registering adapter 0 frontend 0 (Siano Mobile Digital MDTV Receiver)...
	smscore_register_client: ffff88012174a000 693 1
	sms_board_dvb3_event: DVB3_EVENT_HOTPLUG
	smsdvb_hotplug: success
	smsdvb_module_init:
Signed-off-by: default avatarMauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: default avatarAndré Roth <neolynx@gmail.com>
Signed-off-by: default avatarMauro Carvalho Chehab <m.chehab@samsung.com>
parent f43b396c
......@@ -491,15 +491,26 @@ static int smsusb_probe(struct usb_interface *intf,
}
if (id->driver_info == SMS1XXX_BOARD_SIANO_STELLAR_ROM) {
/* Detected a Siano Stellar uninitialized */
snprintf(devpath, sizeof(devpath), "usb\\%d-%s",
udev->bus->busnum, udev->devpath);
sms_info("stellar device was found.");
return smsusb1_load_firmware(
sms_info("stellar device in cold state was found at %s.", devpath);
rc = smsusb1_load_firmware(
udev, smscore_registry_getmode(devpath),
id->driver_info);
/* This device will reset and gain another USB ID */
if (!rc)
sms_info("stellar device now in warm state");
else
sms_err("Failed to put stellar in warm state. Error: %d", rc);
return rc;
} else {
rc = smsusb_init_device(intf, id->driver_info);
}
rc = smsusb_init_device(intf, id->driver_info);
sms_info("Device initialized with return code %d", rc);
sms_board_load_modules(id->driver_info);
return rc;
......@@ -552,10 +563,13 @@ static int smsusb_resume(struct usb_interface *intf)
}
static const struct usb_device_id smsusb_id_table[] = {
/* This device is only present before firmware load */
{ USB_DEVICE(0x187f, 0x0010),
.driver_info = SMS1XXX_BOARD_SIANO_STELLAR },
.driver_info = SMS1XXX_BOARD_SIANO_STELLAR_ROM },
/* This device pops up after firmware load */
{ USB_DEVICE(0x187f, 0x0100),
.driver_info = SMS1XXX_BOARD_SIANO_STELLAR },
{ USB_DEVICE(0x187f, 0x0200),
.driver_info = SMS1XXX_BOARD_SIANO_NOVA_A },
{ USB_DEVICE(0x187f, 0x0201),
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment