Merge tag 'arm-soc/for-4.15/devicetree' of http://github.com/Broadcom/stblinux into next/dt

Pull "Broadcom devicetree changes for 4.15" from Florian Fainelli:

This pull request contains Broadcom ARM-based Device Tree changes for 4.15,
please pull the following:

- Eric adds support for the CLCD and PWM controller on Cygnus chis

- Loic fixes the console path on the Raspberry Pi 3 (already submitted as
  fixes) and then proceeds with enabling the BCM43438 bluetooth chip on
  the Raspberry Pi 3

- Rafal specifies the USB ports on the Luxul XWR-1200

- Dan adds support for the Luxul ABR-4500 based on BCM47094, the Luxul XAP-810
  and XAP-1440 both based on BCM53573

- Florian adds support for the Broadcom Hurricane 2 SoC by adding general
  machine binding, clock binding, SoC DTS include file and a DTS for the
  Ubiquiti Networks UniFi Switch 8

* tag 'arm-soc/for-4.15/devicetree' of http://github.com/Broadcom/stblinux:
  ARM: dts: Hurricane 2: Add basic support for Ubiquiti UniFi Switch 8
  dt-bindings: Add Ubiquiti Networks vendor prefix
  ARM: dts: Add Broadcom Hurricane 2 DTS include file
  dt-bindings: Document Broadcom Hurricane 2 clocks
  dt-bindings: Add documentation for Broadcom Hurricane 2 SoCs
  ARM: dts: BCM53573: Add DT for Luxul XAP-1440
  ARM: dts: BCM53573: Add DT for Luxul XAP-810
  ARM: dts: BCM5301X: Add DT for Luxul ABR-4500
  ARM: dts: BCM5301X: Add DT for Luxul XBR-4500
  ARM: dts: BCM5301X: Specify USB ports for USB LED of Luxul XWR-1200
  ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
  ARM: dts: bcm283x: Fix console path on RPi3
  ARM: dts: cygnus: Add the PWM node
  ARM: dts: cygnus: Add the CLCD controller

Documentation/devicetree/bindings/arm/bcm/brcm,hr2.txt

+Broadcom Hurricane 2 device tree bindings
+---------------------------------------
+
+Broadcom Hurricane 2 family of SoCs are used for switching control. These SoCs
+are based on Broadcom's iProc SoC architecture and feature a single core Cortex
+A9 ARM CPUs, DDR2/DDR3 memory, PCIe GEN-2, USB 2.0 and USB 3.0, serial and NAND
+flash and a PCIe attached integrated switching engine.
+
+Boards with Hurricane SoCs shall have the following properties:
+
+Required root node property:
+
+BCM53342
+compatible = "brcm,bcm53342", "brcm,hr2";

Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt

@@ -137,6 +137,20 @@ These clock IDs are defined in:
     ch1_audio  audiopll         2       BCM_CYGNUS_AUDIOPLL_CH1
     ch2_audio  audiopll         3       BCM_CYGNUS_AUDIOPLL_CH2
 
+Hurricane 2
+------
+PLL and leaf clock compatible strings for Hurricane 2 are:
+ "brcm,hr2-armpll"
+
+The following table defines the set of PLL/clock for Hurricane 2:
+
+    Clock	Source		Index	ID
+    ---		-----		-----	---------
+    crystal	N/A		N/A	N/A
+
+    armpll	crystal		N/A	N/A
+
+
 Northstar and Northstar Plus
 ------
 PLL and leaf clock compatible strings for Northstar and Northstar Plus are:

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -354,6 +354,7 @@ truly	Truly Semiconductors Limited
 tsd	Theobroma Systems Design und Consulting GmbH
 tyan	Tyan Computer Corporation
 ucrobotics	uCRobotics
+ubnt	Ubiquiti Networks
 udoo	Udoo
 uniwest	United Western Technologies Corp (UniWest)
 upisemi	uPI Semiconductor Corp.

arch/arm/boot/dts/Makefile

@@ -100,6 +100,8 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-tplink-archer-c9-v1.dtb \
 	bcm47094-dlink-dir-885l.dtb \
 	bcm47094-linksys-panamera.dtb \
+	bcm47094-luxul-abr-4500.dtb \
+	bcm47094-luxul-xbr-4500.dtb \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm94708.dtb \
@@ -108,6 +110,8 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm953012hr.dtb \
 	bcm953012k.dtb
 dtb-$(CONFIG_ARCH_BCM_53573) += \
+	bcm47189-luxul-xap-1440.dtb \
+	bcm47189-luxul-xap-810.dtb \
 	bcm47189-tenda-ac9.dtb \
 	bcm947189acdbmr.dtb
 dtb-$(CONFIG_ARCH_BCM_63XX) += \
@@ -117,6 +121,8 @@ dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
 	bcm911360k.dtb \
 	bcm958300k.dtb \
 	bcm958305k.dtb
+dtb-$(CONFIG_ARCH_BCM_HR2) += \
+	bcm53340-ubnt-unifi-switch8.dtb
 dtb-$(CONFIG_ARCH_BCM_MOBILE) += \
 	bcm28155-ap.dtb \
 	bcm21664-garnet.dtb \

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -473,6 +473,16 @@ ohci0: usb@18048800 {
 			status = "disabled";
 		};
 
+		clcd: clcd@180a0000 {
+			compatible = "arm,pl111", "arm,primecell";
+			reg = <0x180a0000 0x1000>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "combined";
+			clocks = <&axi41_clk>, <&apb_clk>;
+			clock-names = "clcdclk", "apb_pclk";
+			status = "disabled";
+		};
+
 		v3d: v3d@180a2000 {
 			compatible = "brcm,cygnus-v3d";
 			reg = <0x180a2000 0x1000>;
@@ -575,6 +585,14 @@ adc: adc@180a6000 {
 			status = "disabled";
 		};
 
+		pwm: pwm@180aa500 {
+			compatible = "brcm,kona-pwm";
+			reg = <0x180aa500 0xc4>;
+			#pwm-cells = <3>;
+			clocks = <&asiu_clks BCM_CYGNUS_ASIU_PWM_CLK>;
+			status = "disabled";
+		};
+
 		keypad: keypad@180ac000 {
 			compatible = "brcm,bcm-keypad";
 			reg = <0x180ac000 0x14c>;

arch/arm/boot/dts/bcm-hr2.dtsi

+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2017 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,hr2";
+	model = "Broadcom Hurricane 2 SoC";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
+			      GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+	};
+
+	mpcore@19000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x19000000 0x00023000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		a9pll: arm_clk@0 {
+			#clock-cells = <0>;
+			compatible = "brcm,hr2-armpll";
+			clocks = <&osc>;
+			reg = <0x0 0x1000>;
+		};
+
+		timer@20200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0x20200 0x100>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+		};
+
+		twd-timer@20600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x20600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
+						  IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&periph_clk>;
+		};
+
+		twd-watchdog@20620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0x20620 0x20>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) |
+						  IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&periph_clk>;
+		};
+
+		gic: interrupt-controller@21000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x21000 0x1000>,
+			      <0x20100 0x100>;
+		};
+
+		L2: l2-cache@22000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x22000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc: oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+		};
+
+		periph_clk: periph_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&a9pll>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+	};
+
+	axi@18000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x18000000 0x0011c40c>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		uart0: serial@300 {
+			compatible = "ns16550a";
+			reg = <0x0300 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		uart1: serial@400 {
+			compatible = "ns16550a";
+			reg = <0x0400 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		dma@20000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x20000 0x1000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			status = "disabled";
+		};
+
+		amac0: ethernet@22000 {
+			compatible = "brcm,nsp-amac";
+			reg = <0x22000 0x1000>,
+			      <0x110000 0x1000>;
+			reg-names = "amac_base", "idm_base";
+			interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		nand: nand@26000 {
+			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
+			reg = <0x26000 0x600>,
+			      <0x11b408 0x600>,
+			      <0x026f00 0x20>;
+			reg-names = "nand", "iproc-idm", "iproc-ext";
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			brcm,nand-has-wp;
+		};
+
+		gpiob: gpio@30000 {
+			compatible = "brcm,iproc-hr2-gpio", "brcm,iproc-gpio";
+			reg = <0x30000 0x50>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			ngpios = <4>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pwm: pwm@31000 {
+			compatible = "brcm,iproc-pwm";
+			reg = <0x31000 0x28>;
+			clocks = <&osc>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		rng: rng@33000 {
+			compatible = "brcm,bcm-nsp-rng";
+			reg = <0x33000 0x14>;
+		};
+
+		qspi: qspi@27200 {
+			compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
+			reg = <0x027200 0x184>,
+			      <0x027000 0x124>,
+			      <0x11c408 0x004>,
+			      <0x0273a0 0x01c>;
+			reg-names = "mspi", "bspi", "intr_regs",
+				    "intr_status_reg";
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overhead",
+					  "mspi_done",
+					  "mspi_halted";
+			num-cs = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* partitions defined in board DTS */
+		};
+
+		ccbtimer0: timer@34000 {
+			compatible = "arm,sp804";
+			reg = <0x34000 0x1000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		ccbtimer1: timer@35000 {
+			compatible = "arm,sp804";
+			reg = <0x35000 0x1000>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		i2c0: i2c@38000 {
+			compatible = "brcm,iproc-i2c";
+			reg = <0x38000 0x50>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_NONE>;
+			clock-frequency = <100000>;
+		};
+
+		watchdog@39000 {
+			compatible = "arm,sp805", "arm,primecell";
+			reg = <0x39000 0x1000>;
+			interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		i2c1: i2c@3b000 {
+			compatible = "brcm,iproc-i2c";
+			reg = <0x3b000 0x50>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>;
+			clock-frequency = <100000>;
+		};
+	};
+
+	pflash: nor@20000000 {
+		compatible = "cfi-flash", "jedec-flash";
+		reg = <0x20000000 0x04000000>;
+		status = "disabled";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* partitions defined in board DTS */
+	};
+
+	pcie0: pcie@18012000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18012000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_NONE>;
+
+		linux,pci-domain = <0>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
+
+		status = "disabled";
+
+		msi-parent = <&msi0>;
+		msi0: msi-controller {
+			compatible = "brcm,iproc-msi";
+			msi-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 182 IRQ_TYPE_NONE>,
+				     <GIC_SPI 183 IRQ_TYPE_NONE>,
+				     <GIC_SPI 184 IRQ_TYPE_NONE>,
+				     <GIC_SPI 185 IRQ_TYPE_NONE>;
+			brcm,pcie-msi-inten;
+		};
+	};
+
+	pcie1: pcie@18013000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18013000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_NONE>;
+
+		linux,pci-domain = <1>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
+
+		status = "disabled";
+
+		msi-parent = <&msi1>;
+		msi1: msi-controller {
+			compatible = "brcm,iproc-msi";
+			msi-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>,
+				     <GIC_SPI 189 IRQ_TYPE_NONE>,
+				     <GIC_SPI 190 IRQ_TYPE_NONE>,
+				     <GIC_SPI 191 IRQ_TYPE_NONE>;
+			brcm,pcie-msi-inten;
+		};
+	};
+};

arch/arm/boot/dts/bcm2835-rpi-zero-w.dts

@@ -18,12 +18,9 @@ / {
 	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
 	model = "Raspberry Pi Zero W";
 
-	/* Needed by firmware to properly init UARTs */
-	aliases {
-		uart0 = "/soc/serial@7e201000";
-		uart1 = "/soc/serial@7e215040";
-		serial0 = "/soc/serial@7e201000";
-		serial1 = "/soc/serial@7e215040";
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
 	};
 
 	leds {

arch/arm/boot/dts/bcm2837-rpi-3-b.dts

@@ -8,6 +8,11 @@ / {
 	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
 	model = "Raspberry Pi 3 Model B";
 
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
 	memory {
 		reg = <0 0x40000000>;
 	};
@@ -24,6 +29,11 @@ &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+	};
 };
 
 /* uart1 is mapped to the pin header */

arch/arm/boot/dts/bcm283x.dtsi

@@ -20,8 +20,13 @@ / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
 	chosen {
-		bootargs = "earlyprintk console=ttyAMA0";
+		stdout-path = "serial0:115200n8";
 	};
 
 	thermal-zones {

arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts

@@ -57,7 +57,8 @@ lan2 {
 		usb {
 			label = "bcm53xx:green:usb";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "none";
+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
+			linux,default-trigger = "usbport";
 		};
 
 		status {

arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts

+/*
+ * Copyright (C) 2017 Luxul Inc.
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "luxul,abr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul ABR-4500 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x18000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+				<&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&spi_nor {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts

+/*
+ * Copyright (C) 2017 Luxul Inc.
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "luxul,xbr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul XBR-4500 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x18000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+
+		usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+				<&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&spi_nor {
+	status = "okay";
+};

arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts

+/*
+ * Copyright 2017 Luxul Inc.
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm53573.dtsi"
+
+/ {
+	compatible = "luxul,xap-1440-v1", "brcm,bcm47189", "brcm,bcm53573";
+	model = "Luxul XAP-1440 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wlan {
+			label = "bcm53xx:blue:wlan";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		system {
+			label = "bcm53xx:green:system";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm47189-luxul-xap-810.dts

+/*
+ * Copyright 2017 Luxul Inc.
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm53573.dtsi"
+
+/ {
+	compatible = "luxul,xap-810-v1", "brcm,bcm47189", "brcm,bcm53573";
+	model = "Luxul XAP-810 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		system {
+			label = "bcm53xx:green:system";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	pcie0_leds {
+		compatible = "gpio-leds";
+
+		2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pcie0 {
+	ranges = <0x00000000 0 0 0 0 0x00100000>;
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0,0 {
+		reg = <0x0000 0 0 0 0>;
+		ranges = <0x00000000 0 0 0 0 0 0 0x00100000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,1,0 {
+			reg = <0x0000 0 0 0 0>;
+			ranges = <0x00000000 0 0 0 0x00100000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pcie0_chipcommon: chipcommon@0 {
+				reg = <0 0x1000>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts

+/*
+ * DTS for Unifi Switch 8 port
+ *
+ * Copyright (C) 2017 Florian Fainelli <f.fainelli@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm-hr2.dtsi"
+
+/ {
+	compatible = "ubnt,unifi-switch8", "brcm,bcm53342", "brcm,hr2";
+	model = "Ubiquiti UniFi Switch 8 (BCM53342)";
+
+	/* Hurricane 2 designs use the second UART */
+	chosen {
+		bootargs = "console=ttyS1,115200 earlyprintk";
+	};
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>,
+		      <0x68000000 0x08000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+
+	flash: m25p80@0 {
+		compatible = "m25p80";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <12500000>;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0xc0000>;
+		};
+
+		partition@c0000 {
+			label = "u-boot-env";
+			reg = <0xc0000 0x10000>;
+		};
+
+		partition@d0000 {
+			label = "shmoo";
+			reg = <0xd0000 0x10000>;
+		};
+
+		partition@e0000 {
+			label = "kernel0";
+			reg = <0xe0000 0xf00000>;
+		};
+
+		partition@fe0000 {
+			label = "kernel1";
+			reg = <0xfe0000 0xf10000>;
+		};
+
+		partition@1ef0000 {
+			label = "cfg";
+			reg = <0x1ef0000 0x100000>;
+		};
+
+		partition@1ff0000 {
+			label = "EEPROM";
+			reg = <0x1ff0000 0x10000>;
+		};
+	};
+};
+
+&pcie0 {
+	/* Attaches to the internal switch */
+	status = "okay";
+};