Commit 8ca783ab authored by Don Skidmore's avatar Don Skidmore Committed by David S. Miller

ixgbe: fix 82598 SFP initialization after driver load.

If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in.  This patch corrects that by:

ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.

ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.

ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected.  Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.

Other functions were updated to allow correct logging.
Signed-off-by: default avatarDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: default avatarPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent f7c86a32
......@@ -698,6 +698,7 @@ static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw,
static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
{
s32 status = 0;
s32 phy_status = 0;
u32 ctrl;
u32 gheccr;
u32 i;
......@@ -745,13 +746,17 @@ static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
/* PHY ops must be identified and initialized prior to reset */
/* Init PHY and function pointers, perform SFP setup */
status = hw->phy.ops.init(hw);
if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
phy_status = hw->phy.ops.init(hw);
if (phy_status == IXGBE_ERR_SFP_NOT_SUPPORTED)
goto reset_hw_out;
else if (phy_status == IXGBE_ERR_SFP_NOT_PRESENT)
goto no_phy_reset;
hw->phy.ops.reset(hw);
}
no_phy_reset:
/*
* Prevent the PCI-E bus from from hanging by disabling PCI-E master
* access and verify no pending requests before reset
......@@ -811,6 +816,9 @@ static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
reset_hw_out:
if (phy_status)
status = phy_status;
return status;
}
......
......@@ -2599,7 +2599,10 @@ int ixgbe_up(struct ixgbe_adapter *adapter)
void ixgbe_reset(struct ixgbe_adapter *adapter)
{
struct ixgbe_hw *hw = &adapter->hw;
if (hw->mac.ops.init_hw(hw))
int err;
err = hw->mac.ops.init_hw(hw);
if (err && (err != IXGBE_ERR_SFP_NOT_PRESENT))
dev_err(&adapter->pdev->dev, "Hardware Error\n");
/* reprogram the RAR[0] in case user changed it. */
......@@ -5167,20 +5170,7 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
INIT_WORK(&adapter->sfp_config_module_task,
ixgbe_sfp_config_module_task);
err = ii->get_invariants(hw);
if (err == IXGBE_ERR_SFP_NOT_PRESENT) {
/* start a kernel thread to watch for a module to arrive */
set_bit(__IXGBE_SFP_MODULE_NOT_FOUND, &adapter->state);
mod_timer(&adapter->sfp_timer,
round_jiffies(jiffies + (2 * HZ)));
err = 0;
} else if (err == IXGBE_ERR_SFP_NOT_SUPPORTED) {
DPRINTK(PROBE, ERR, "failed to load because an "
"unsupported SFP+ module type was detected.\n");
goto err_hw_init;
} else if (err) {
goto err_hw_init;
}
ii->get_invariants(hw);
/* setup the private structure */
err = ixgbe_sw_init(adapter);
......@@ -5200,7 +5190,18 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
/* reset_hw fills in the perm_addr as well */
err = hw->mac.ops.reset_hw(hw);
if (err == IXGBE_ERR_SFP_NOT_SUPPORTED) {
if (err == IXGBE_ERR_SFP_NOT_PRESENT &&
hw->mac.type == ixgbe_mac_82598EB) {
/*
* Start a kernel thread to watch for a module to arrive.
* Only do this for 82598, since 82599 will generate
* interrupts on module arrival.
*/
set_bit(__IXGBE_SFP_MODULE_NOT_FOUND, &adapter->state);
mod_timer(&adapter->sfp_timer,
round_jiffies(jiffies + (2 * HZ)));
err = 0;
} else if (err == IXGBE_ERR_SFP_NOT_SUPPORTED) {
dev_err(&adapter->pdev->dev, "failed to load because an "
"unsupported SFP+ module type was detected.\n");
goto err_sw_init;
......
......@@ -530,11 +530,22 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
u8 cable_tech = 0;
u16 enforce_sfp = 0;
if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_fiber) {
hw->phy.sfp_type = ixgbe_sfp_type_not_present;
status = IXGBE_ERR_SFP_NOT_PRESENT;
goto out;
}
status = hw->phy.ops.read_i2c_eeprom(hw, IXGBE_SFF_IDENTIFIER,
&identifier);
if (status == IXGBE_ERR_SFP_NOT_PRESENT) {
if (status == IXGBE_ERR_SFP_NOT_PRESENT || status == IXGBE_ERR_I2C) {
status = IXGBE_ERR_SFP_NOT_PRESENT;
hw->phy.sfp_type = ixgbe_sfp_type_not_present;
if (hw->phy.type != ixgbe_phy_nl) {
hw->phy.id = 0;
hw->phy.type = ixgbe_phy_unknown;
}
goto out;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment