Merge branch 'arm-next' of git://git.xilinx.com/linux-xlnx into next/dt

From Michal Simek <michal.simek@xilinx.com>:

These are based on previous patches (arm-soc zynq/cleanup branch).
The branch is still based on rc3 but I have also tried to merged it
with the v3.7-rc5 and there is no issue.

* 'arm-next' of git://git.xilinx.com/linux-xlnx:
  ARM: zynq: add clk binding support to the ttc
  ARM: zynq: use zynq clk bindings
  clk: Add support for fundamental zynq clks
  ARM: zynq: dts: split up device tree
  ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
  ARM: zynq: dts: add description of the second uart
  ARM: zynq: move arm-specific sys_timer out of ttc
  zynq: move static peripheral mappings
  zynq: remove use of CLKDEV_LOOKUP
  zynq: use pl310 device tree bindings
  zynq: use GIC device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/clock/zynq-7000.txt

+Device Tree Clock bindings for the Zynq 7000 EPP
+
+The Zynq EPP has several different clk providers, each with there own bindings.
+The purpose of this document is to document their usage.
+
+See clock_bindings.txt for more information on the generic clock bindings.
+See Chapter 25 of Zynq TRM for more information about Zynq clocks.
+
+== PLLs ==
+
+Used to describe the ARM_PLL, DDR_PLL, and IO_PLL.
+
+Required properties:
+- #clock-cells : shall be 0 (only one clock is output from this node)
+- compatible : "xlnx,zynq-pll"
+- reg : pair of u32 values, which are the address offsets within the SLCR
+        of the relevant PLL_CTRL register and PLL_CFG register respectively
+- clocks : phandle for parent clock.  should be the phandle for ps_clk
+
+Optional properties:
+- clock-output-names : name of the output clock
+
+Example:
+	armpll: armpll {
+		#clock-cells = <0>;
+		compatible = "xlnx,zynq-pll";
+		clocks = <&ps_clk>;
+		reg = <0x100 0x110>;
+		clock-output-names = "armpll";
+	};
+
+== Peripheral clocks ==
+
+Describes clock node for the SDIO, SMC, SPI, QSPI, and UART clocks.
+
+Required properties:
+- #clock-cells : shall be 1
+- compatible : "xlnx,zynq-periph-clock"
+- reg : a single u32 value, describing the offset within the SLCR where
+        the CLK_CTRL register is found for this peripheral
+- clocks : phandle for parent clocks.  should hold phandles for
+           the IO_PLL, ARM_PLL, and DDR_PLL in order
+- clock-output-names : names of the output clock(s).  For peripherals that have
+                       two output clocks (for example, the UART), two clocks
+                       should be listed.
+
+Example:
+	uart_clk: uart_clk {
+		#clock-cells = <1>;
+		compatible = "xlnx,zynq-periph-clock";
+		clocks = <&iopll &armpll &ddrpll>;
+		reg = <0x154>;
+		clock-output-names = "uart0_ref_clk",
+				     "uart1_ref_clk";
+	};

arch/arm/Kconfig

@@ -945,7 +945,7 @@ config ARCH_ZYNQ
 	bool "Xilinx Zynq ARM Cortex A9 Platform"
 	select ARM_AMBA
 	select ARM_GIC
-	select CLKDEV_LOOKUP
+	select COMMON_CLK
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select ICST

arch/arm/Kconfig.debug

@@ -132,6 +132,23 @@ choice
 		  their output to UART1 serial port on DaVinci TNETV107X
 		  devices.
 
+	config DEBUG_ZYNQ_UART0
+		bool "Kernel low-level debugging on Xilinx Zynq using UART0"
+		depends on ARCH_ZYNQ
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART0 on the Zynq platform.
+
+	config DEBUG_ZYNQ_UART1
+		bool "Kernel low-level debugging on Xilinx Zynq using UART1"
+		depends on ARCH_ZYNQ
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART1 on the Zynq platform.
+
+		  If you have a ZC702 board and want early boot messages to
+		  appear on the USB serial adaptor, select this option.
+
 	config DEBUG_DC21285_PORT
 		bool "Kernel low-level debugging messages via footbridge serial port"
 		depends on FOOTBRIDGE

arch/arm/Makefile

@@ -198,7 +198,6 @@ machine-$(CONFIG_ARCH_ZYNQ)		+= zynq
 # by CONFIG_* macro name.
 plat-$(CONFIG_ARCH_OMAP)	+= omap
 plat-$(CONFIG_ARCH_S3C64XX)	+= samsung
-plat-$(CONFIG_ARCH_ZYNQ)	+= versatile
 plat-$(CONFIG_PLAT_IOP)		+= iop
 plat-$(CONFIG_PLAT_NOMADIK)	+= nomadik
 plat-$(CONFIG_PLAT_ORION)	+= orion

arch/arm/boot/dts/Makefile

@@ -105,5 +105,6 @@ dtb-$(CONFIG_ARCH_VEXPRESS) += vexpress-v2p-ca5s.dtb \
 dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
 	wm8505-ref.dtb \
 	wm8650-mid.dtb
+dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb
 
 endif

arch/arm/boot/dts/zynq-7000.dtsi

+/*
+ *  Copyright (C) 2011 Xilinx
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "xlnx,zynq-7000";
+
+	amba {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+
+		intc: interrupt-controller@f8f01000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <1>;
+			interrupt-controller;
+			reg = <0xF8F01000 0x1000>,
+			      <0xF8F00100 0x100>;
+		};
+
+		L2: cache-controller {
+			compatible = "arm,pl310-cache";
+			reg = <0xF8F02000 0x1000>;
+			arm,data-latency = <2 3 2>;
+			arm,tag-latency = <2 3 2>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		uart0: uart@e0000000 {
+			compatible = "xlnx,xuartps";
+			reg = <0xE0000000 0x1000>;
+			interrupts = <0 27 4>;
+			clock = <50000000>;
+		};
+
+		uart1: uart@e0001000 {
+			compatible = "xlnx,xuartps";
+			reg = <0xE0001000 0x1000>;
+			interrupts = <0 50 4>;
+			clock = <50000000>;
+		};
+
+		slcr: slcr@f8000000 {
+			compatible = "xlnx,zynq-slcr";
+			reg = <0xF8000000 0x1000>;
+
+			clocks {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ps_clk: ps_clk {
+					#clock-cells = <0>;
+					compatible = "fixed-clock";
+					/* clock-frequency set in board-specific file */
+					clock-output-names = "ps_clk";
+				};
+				armpll: armpll {
+					#clock-cells = <0>;
+					compatible = "xlnx,zynq-pll";
+					clocks = <&ps_clk>;
+					reg = <0x100 0x110>;
+					clock-output-names = "armpll";
+				};
+				ddrpll: ddrpll {
+					#clock-cells = <0>;
+					compatible = "xlnx,zynq-pll";
+					clocks = <&ps_clk>;
+					reg = <0x104 0x114>;
+					clock-output-names = "ddrpll";
+				};
+				iopll: iopll {
+					#clock-cells = <0>;
+					compatible = "xlnx,zynq-pll";
+					clocks = <&ps_clk>;
+					reg = <0x108 0x118>;
+					clock-output-names = "iopll";
+				};
+				uart_clk: uart_clk {
+					#clock-cells = <1>;
+					compatible = "xlnx,zynq-periph-clock";
+					clocks = <&iopll &armpll &ddrpll>;
+					reg = <0x154>;
+					clock-output-names = "uart0_ref_clk",
+							     "uart1_ref_clk";
+				};
+				cpu_clk: cpu_clk {
+					#clock-cells = <1>;
+					compatible = "xlnx,zynq-cpu-clock";
+					clocks = <&iopll &armpll &ddrpll>;
+					reg = <0x120 0x1C4>;
+					clock-output-names = "cpu_6x4x",
+							     "cpu_3x2x",
+							     "cpu_2x",
+							     "cpu_1x";
+				};
+			};
+		};
+
+		ttc0: ttc0@f8001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "xlnx,ttc";
+			reg = <0xF8001000 0x1000>;
+			clocks = <&cpu_clk 3>;
+			clock-names = "cpu_1x";
+			clock-ranges;
+
+			ttc0_0: ttc0.0 {
+				status = "disabled";
+				reg = <0>;
+				interrupts = <0 10 4>;
+			};
+			ttc0_1: ttc0.1 {
+				status = "disabled";
+				reg = <1>;
+				interrupts = <0 11 4>;
+			};
+			ttc0_2: ttc0.2 {
+				status = "disabled";
+				reg = <2>;
+				interrupts = <0 12 4>;
+			};
+		};
+
+		ttc1: ttc1@f8002000 {
+			#interrupt-parent = <&intc>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "xlnx,ttc";
+			reg = <0xF8002000 0x1000>;
+			clocks = <&cpu_clk 3>;
+			clock-names = "cpu_1x";
+			clock-ranges;
+
+			ttc1_0: ttc1.0 {
+				status = "disabled";
+				reg = <0>;
+				interrupts = <0 37 4>;
+			};
+			ttc1_1: ttc1.1 {
+				status = "disabled";
+				reg = <1>;
+				interrupts = <0 38 4>;
+			};
+			ttc1_2: ttc1.2 {
+				status = "disabled";
+				reg = <2>;
+				interrupts = <0 39 4>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/zynq-ep107.dts

-/*
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/dts-v1/;
-/ {
-	model = "Xilinx Zynq EP107";
-	compatible = "xlnx,zynq-ep107";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&intc>;
-
-	memory {
-		device_type = "memory";
-		reg = <0x0 0x10000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyPS0,9600 root=/dev/ram rw initrd=0x800000,8M earlyprintk";
-		linux,stdout-path = &uart0;
-	};
-
-	amba {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		intc: interrupt-controller@f8f01000 {
-			interrupt-controller;
-			compatible = "arm,gic";
-			reg = <0xF8F01000 0x1000>;
-			#interrupt-cells = <2>;
-		};
-
-		uart0: uart@e0000000 {
-			compatible = "xlnx,xuartps";
-			reg = <0xE0000000 0x1000>;
-			interrupts = <59 0>;
-			clock = <50000000>;
-		};
-	};
-};

arch/arm/mach-zynq/include/mach/clkdev.h → arch/arm/boot/dts/zynq-zc702.dts

 /*
- * arch/arm/mach-zynq/include/mach/clkdev.h
- *
- *  Copyright (C) 2011 Xilinx, Inc.
+ *  Copyright (C) 2011 Xilinx
+ *  Copyright (C) 2012 National Instruments Corp.
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -11,22 +10,35 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
  */
+/dts-v1/;
+/include/ "zynq-7000.dtsi"
 
-#ifndef __MACH_CLKDEV_H__
-#define __MACH_CLKDEV_H__
+/ {
+	model = "Zynq ZC702 Development Board";
+	compatible = "xlnx,zynq-zc702", "xlnx,zynq-7000";
 
-#include <plat/clock.h>
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x40000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyPS1,115200 earlyprintk";
+	};
 
-struct clk {
-	unsigned long		rate;
-	const struct clk_ops	*ops;
-	const struct icst_params *params;
-	void __iomem		*vcoreg;
 };
 
-#define __clk_get(clk) ({ 1; })
-#define __clk_put(clk) do { } while (0)
+&ps_clk {
+	clock-frequency = <33333330>;
+};
 
-#endif
+&ttc0_0 {
+	status = "ok";
+	compatible = "xlnx,ttc-counter-clocksource";
+};
+
+&ttc0_1 {
+	status = "ok";
+	compatible = "xlnx,ttc-counter-clockevent";
+};

arch/arm/mach-zynq/common.c

@@ -19,19 +19,21 @@
 #include <linux/cpumask.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
+#include <linux/clk/zynq.h>
+#include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/of.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
+#include <asm/mach/time.h>
 #include <asm/mach-types.h>
 #include <asm/page.h>
 #include <asm/hardware/gic.h>
 #include <asm/hardware/cache-l2x0.h>
 
 #include <mach/zynq_soc.h>
-#include <mach/clkdev.h>
 #include "common.h"
 
 static struct of_device_id zynq_of_bus_ids[] __initdata = {
@@ -45,22 +47,25 @@ static struct of_device_id zynq_of_bus_ids[] __initdata = {
  */
 static void __init xilinx_init_machine(void)
 {
-#ifdef CONFIG_CACHE_L2X0
 	/*
 	 * 64KB way size, 8-way associativity, parity disabled
 	 */
-	l2x0_init(PL310_L2CC_BASE, 0x02060000, 0xF0F0FFFF);
-#endif
+	l2x0_of_init(0x02060000, 0xF0F0FFFF);
 
 	of_platform_bus_probe(NULL, zynq_of_bus_ids, NULL);
 }
 
+static struct of_device_id irq_match[] __initdata = {
+	{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
+	{ }
+};
+
 /**
  * xilinx_irq_init() - Interrupt controller initialization for the GIC.
  */
 static void __init xilinx_irq_init(void)
 {
-	gic_init(0, 29, SCU_GIC_DIST_BASE, SCU_GIC_CPU_BASE);
+	of_irq_init(irq_match);
 }
 
 /* The minimum devices needed to be mapped before the VM system is up and
@@ -71,31 +76,47 @@ static struct map_desc io_desc[] __initdata = {
 	{
 		.virtual	= TTC0_VIRT,
 		.pfn		= __phys_to_pfn(TTC0_PHYS),
-		.length		= SZ_4K,
+		.length		= TTC0_SIZE,
 		.type		= MT_DEVICE,
 	}, {
 		.virtual	= SCU_PERIPH_VIRT,
 		.pfn		= __phys_to_pfn(SCU_PERIPH_PHYS),
-		.length		= SZ_8K,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= PL310_L2CC_VIRT,
-		.pfn		= __phys_to_pfn(PL310_L2CC_PHYS),
-		.length		= SZ_4K,
+		.length		= SCU_PERIPH_SIZE,
 		.type		= MT_DEVICE,
 	},
 
 #ifdef CONFIG_DEBUG_LL
 	{
-		.virtual	= UART0_VIRT,
-		.pfn		= __phys_to_pfn(UART0_PHYS),
-		.length		= SZ_4K,
+		.virtual	= LL_UART_VADDR,
+		.pfn		= __phys_to_pfn(LL_UART_PADDR),
+		.length		= UART_SIZE,
 		.type		= MT_DEVICE,
 	},
 #endif
 
 };
 
+static void __init xilinx_zynq_timer_init(void)
+{
+	struct device_node *np;
+	void __iomem *slcr;
+
+	np = of_find_compatible_node(NULL, NULL, "xlnx,zynq-slcr");
+	slcr = of_iomap(np, 0);
+	WARN_ON(!slcr);
+
+	xilinx_zynq_clocks_init(slcr);
+
+	xttcpss_timer_init();
+}
+
+/*
+ * Instantiate and initialize the system timer structure
+ */
+static struct sys_timer xttcpss_sys_timer = {
+	.init		= xilinx_zynq_timer_init,
+};
+
 /**
  * xilinx_map_io() - Create memory mappings needed for early I/O.
  */
@@ -105,7 +126,8 @@ static void __init xilinx_map_io(void)
 }
 
 static const char *xilinx_dt_match[] = {
-	"xlnx,zynq-ep107",
+	"xlnx,zynq-zc702",
+	"xlnx,zynq-7000",
 	NULL
 };
 

arch/arm/mach-zynq/common.h

@@ -17,8 +17,6 @@
 #ifndef __MACH_ZYNQ_COMMON_H__
 #define __MACH_ZYNQ_COMMON_H__
 
-#include <asm/mach/time.h>
-
-extern struct sys_timer xttcpss_sys_timer;
+void __init xttcpss_timer_init(void);
 
 #endif

arch/arm/mach-zynq/include/mach/zynq_soc.h

@@ -15,34 +15,39 @@
 #ifndef __MACH_XILINX_SOC_H__
 #define __MACH_XILINX_SOC_H__
 
+#include <asm/pgtable.h>
+
 #define PERIPHERAL_CLOCK_RATE		2500000
 
-/* For now, all mappings are flat (physical = virtual)
+/* Static peripheral mappings are mapped at the top of the vmalloc region.  The
+ * early uart mapping causes intermediate problems/failure at certain
+ * addresses, including the very top of the vmalloc region.  Map it at an
+ * address that is known to work.
  */
-#define UART0_PHYS			0xE0000000
-#define UART0_VIRT			UART0_PHYS
-
-#define TTC0_PHYS			0xF8001000
-#define TTC0_VIRT			TTC0_PHYS
-
-#define PL310_L2CC_PHYS			0xF8F02000
-#define PL310_L2CC_VIRT			PL310_L2CC_PHYS
+#define UART0_PHYS		0xE0000000
+#define UART1_PHYS		0xE0001000
+#define UART_SIZE		SZ_4K
+#define UART_VIRT		0xF0001000
+
+#define TTC0_PHYS		0xF8001000
+#define TTC0_SIZE		SZ_4K
+#define TTC0_VIRT		(VMALLOC_END - TTC0_SIZE)
+
+#define SCU_PERIPH_PHYS		0xF8F00000
+#define SCU_PERIPH_SIZE		SZ_8K
+#define SCU_PERIPH_VIRT		(TTC0_VIRT - SCU_PERIPH_SIZE)
+
+#if IS_ENABLED(CONFIG_DEBUG_ZYNQ_UART1)
+# define LL_UART_PADDR		UART1_PHYS
+#else
+# define LL_UART_PADDR		UART0_PHYS
+#endif
 
-#define SCU_PERIPH_PHYS			0xF8F00000
-#define SCU_PERIPH_VIRT			SCU_PERIPH_PHYS
+#define LL_UART_VADDR		UART_VIRT
 
 /* The following are intended for the devices that are mapped early */
 
 #define TTC0_BASE			IOMEM(TTC0_VIRT)
 #define SCU_PERIPH_BASE			IOMEM(SCU_PERIPH_VIRT)
-#define SCU_GIC_CPU_BASE		(SCU_PERIPH_BASE + 0x100)
-#define SCU_GIC_DIST_BASE		(SCU_PERIPH_BASE + 0x1000)
-#define PL310_L2CC_BASE			IOMEM(PL310_L2CC_VIRT)
-
-/*
- * Mandatory for CONFIG_LL_DEBUG, UART is mapped virtual = physical
- */
-#define LL_UART_PADDR	UART0_PHYS
-#define LL_UART_VADDR	UART0_VIRT
 
 #endif

drivers/clk/Makefile

@@ -19,6 +19,7 @@ endif
 obj-$(CONFIG_MACH_LOONGSON1)	+= clk-ls1x.o
 obj-$(CONFIG_ARCH_U8500)	+= ux500/
 obj-$(CONFIG_ARCH_VT8500)	+= clk-vt8500.o
+obj-$(CONFIG_ARCH_ZYNQ)		+= clk-zynq.o
 
 # Chip specific
 obj-$(CONFIG_COMMON_CLK_WM831X) += clk-wm831x.o

drivers/clk/clk-zynq.c

+/*
+ * Copyright (c) 2012 National Instruments
+ *
+ * Josh Cartwright <josh.cartwright@ni.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/slab.h>
+#include <linux/kernel.h>
+#include <linux/clk-provider.h>
+
+static void __iomem *slcr_base;
+
+struct zynq_pll_clk {
+	struct clk_hw	hw;
+	void __iomem	*pll_ctrl;
+	void __iomem	*pll_cfg;
+};
+
+#define to_zynq_pll_clk(hw)	container_of(hw, struct zynq_pll_clk, hw)
+
+#define CTRL_PLL_FDIV(x)	((x) >> 12)
+
+static unsigned long zynq_pll_recalc_rate(struct clk_hw *hw,
+					  unsigned long parent_rate)
+{
+	struct zynq_pll_clk *pll = to_zynq_pll_clk(hw);
+	return parent_rate * CTRL_PLL_FDIV(ioread32(pll->pll_ctrl));
+}
+
+static const struct clk_ops zynq_pll_clk_ops = {
+	.recalc_rate	= zynq_pll_recalc_rate,
+};
+
+static void __init zynq_pll_clk_setup(struct device_node *np)
+{
+	struct clk_init_data init;
+	struct zynq_pll_clk *pll;
+	const char *parent_name;
+	struct clk *clk;
+	u32 regs[2];
+	int ret;
+
+	ret = of_property_read_u32_array(np, "reg", regs, ARRAY_SIZE(regs));
+	if (WARN_ON(ret))
+		return;
+
+	pll = kzalloc(sizeof(*pll), GFP_KERNEL);
+	if (WARN_ON(!pll))
+		return;
+
+	pll->pll_ctrl = slcr_base + regs[0];
+	pll->pll_cfg  = slcr_base + regs[1];
+
+	of_property_read_string(np, "clock-output-names", &init.name);
+
+	init.ops = &zynq_pll_clk_ops;
+	parent_name = of_clk_get_parent_name(np, 0);
+	init.parent_names = &parent_name;
+	init.num_parents = 1;
+
+	pll->hw.init = &init;
+
+	clk = clk_register(NULL, &pll->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return;
+
+	ret = of_clk_add_provider(np, of_clk_src_simple_get, clk);
+	if (WARN_ON(ret))
+		return;
+}
+
+struct zynq_periph_clk {
+	struct clk_hw		hw;
+	struct clk_onecell_data	onecell_data;
+	struct clk		*gates[2];
+	void __iomem		*clk_ctrl;
+	spinlock_t		clkact_lock;
+};
+
+#define to_zynq_periph_clk(hw)	container_of(hw, struct zynq_periph_clk, hw)
+
+static const u8 periph_clk_parent_map[] = {
+	0, 0, 1, 2
+};
+#define PERIPH_CLK_CTRL_SRC(x)	(periph_clk_parent_map[((x) & 0x30) >> 4])
+#define PERIPH_CLK_CTRL_DIV(x)	(((x) & 0x3F00) >> 8)
+
+static unsigned long zynq_periph_recalc_rate(struct clk_hw *hw,
+					     unsigned long parent_rate)
+{
+	struct zynq_periph_clk *periph = to_zynq_periph_clk(hw);
+	return parent_rate / PERIPH_CLK_CTRL_DIV(ioread32(periph->clk_ctrl));
+}
+
+static u8 zynq_periph_get_parent(struct clk_hw *hw)
+{
+	struct zynq_periph_clk *periph = to_zynq_periph_clk(hw);
+	return PERIPH_CLK_CTRL_SRC(ioread32(periph->clk_ctrl));
+}
+
+static const struct clk_ops zynq_periph_clk_ops = {
+	.recalc_rate	= zynq_periph_recalc_rate,
+	.get_parent	= zynq_periph_get_parent,
+};
+
+static void __init zynq_periph_clk_setup(struct device_node *np)
+{
+	struct zynq_periph_clk *periph;
+	const char *parent_names[3];
+	struct clk_init_data init;
+	int clk_num = 0, err;
+	const char *name;
+	struct clk *clk;
+	u32 reg;
+	int i;
+
+	err = of_property_read_u32(np, "reg", &reg);
+	if (WARN_ON(err))
+		return;
+
+	periph = kzalloc(sizeof(*periph), GFP_KERNEL);
+	if (WARN_ON(!periph))
+		return;
+
+	periph->clk_ctrl = slcr_base + reg;
+	spin_lock_init(&periph->clkact_lock);
+
+	init.name = np->name;
+	init.ops = &zynq_periph_clk_ops;
+	for (i = 0; i < ARRAY_SIZE(parent_names); i++)
+		parent_names[i] = of_clk_get_parent_name(np, i);
+	init.parent_names = parent_names;
+	init.num_parents = ARRAY_SIZE(parent_names);
+
+	periph->hw.init = &init;
+
+	clk = clk_register(NULL, &periph->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return;
+
+	err = of_clk_add_provider(np, of_clk_src_simple_get, clk);
+	if (WARN_ON(err))
+		return;
+
+	err = of_property_read_string_index(np, "clock-output-names", 0,
+					    &name);
+	if (WARN_ON(err))
+		return;
+
+	periph->gates[0] = clk_register_gate(NULL, name, np->name, 0,
+					     periph->clk_ctrl, 0, 0,
+					     &periph->clkact_lock);
+	if (WARN_ON(IS_ERR(periph->gates[0])))
+		return;
+	clk_num++;
+
+	/* some periph clks have 2 downstream gates */
+	err = of_property_read_string_index(np, "clock-output-names", 1,
+					    &name);
+	if (err != -ENODATA) {
+		periph->gates[1] = clk_register_gate(NULL, name, np->name, 0,
+						     periph->clk_ctrl, 1, 0,
+						     &periph->clkact_lock);
+		if (WARN_ON(IS_ERR(periph->gates[1])))
+			return;
+		clk_num++;
+	}
+
+	periph->onecell_data.clks = periph->gates;
+	periph->onecell_data.clk_num = clk_num;
+
+	err = of_clk_add_provider(np, of_clk_src_onecell_get,
+				  &periph->onecell_data);
+	if (WARN_ON(err))
+		return;
+}
+
+/* CPU Clock domain is modelled as a mux with 4 children subclks, whose
+ * derivative rates depend on CLK_621_TRUE
+ */
+
+struct zynq_cpu_clk {
+	struct clk_hw		hw;
+	struct clk_onecell_data	onecell_data;
+	struct clk		*subclks[4];
+	void __iomem		*clk_ctrl;
+	spinlock_t		clkact_lock;
+};
+
+#define to_zynq_cpu_clk(hw)	container_of(hw, struct zynq_cpu_clk, hw)
+
+static const u8 zynq_cpu_clk_parent_map[] = {
+	1, 1, 2, 0
+};
+#define CPU_CLK_SRCSEL(x)	(zynq_cpu_clk_parent_map[(((x) & 0x30) >> 4)])
+#define CPU_CLK_CTRL_DIV(x)	(((x) & 0x3F00) >> 8)
+
+static u8 zynq_cpu_clk_get_parent(struct clk_hw *hw)
+{
+	struct zynq_cpu_clk *cpuclk = to_zynq_cpu_clk(hw);
+	return CPU_CLK_SRCSEL(ioread32(cpuclk->clk_ctrl));
+}
+
+static unsigned long zynq_cpu_clk_recalc_rate(struct clk_hw *hw,
+					      unsigned long parent_rate)
+{
+	struct zynq_cpu_clk *cpuclk = to_zynq_cpu_clk(hw);
+	return parent_rate / CPU_CLK_CTRL_DIV(ioread32(cpuclk->clk_ctrl));
+}
+
+static const struct clk_ops zynq_cpu_clk_ops = {
+	.get_parent	= zynq_cpu_clk_get_parent,
+	.recalc_rate	= zynq_cpu_clk_recalc_rate,
+};
+
+struct zynq_cpu_subclk {
+	struct clk_hw	hw;
+	void __iomem	*clk_621;
+	enum {
+		CPU_SUBCLK_6X4X,
+		CPU_SUBCLK_3X2X,
+		CPU_SUBCLK_2X,
+		CPU_SUBCLK_1X,
+	} which;
+};
+
+#define CLK_621_TRUE(x)	((x) & 1)
+
+#define to_zynq_cpu_subclk(hw)	container_of(hw, struct zynq_cpu_subclk, hw);
+
+static unsigned long zynq_cpu_subclk_recalc_rate(struct clk_hw *hw,
+						 unsigned long parent_rate)
+{
+	unsigned long uninitialized_var(rate);
+	struct zynq_cpu_subclk *subclk;
+	bool is_621;
+
+	subclk = to_zynq_cpu_subclk(hw)
+	is_621 = CLK_621_TRUE(ioread32(subclk->clk_621));
+
+	switch (subclk->which) {
+	case CPU_SUBCLK_6X4X:
+		rate = parent_rate;
+		break;
+	case CPU_SUBCLK_3X2X:
+		rate = parent_rate / 2;
+		break;
+	case CPU_SUBCLK_2X:
+		rate = parent_rate / (is_621 ? 3 : 2);
+		break;
+	case CPU_SUBCLK_1X:
+		rate = parent_rate / (is_621 ? 6 : 4);
+		break;
+	};
+
+	return rate;
+}
+
+static const struct clk_ops zynq_cpu_subclk_ops = {
+	.recalc_rate	= zynq_cpu_subclk_recalc_rate,
+};
+
+static struct clk *zynq_cpu_subclk_setup(struct device_node *np, u8 which,
+					 void __iomem *clk_621)
+{
+	struct zynq_cpu_subclk *subclk;
+	struct clk_init_data init;
+	struct clk *clk;
+	int err;
+
+	err = of_property_read_string_index(np, "clock-output-names",
+					    which, &init.name);
+	if (WARN_ON(err))
+		goto err_read_output_name;
+
+	subclk = kzalloc(sizeof(*subclk), GFP_KERNEL);
+	if (!subclk)
+		goto err_subclk_alloc;
+
+	subclk->clk_621 = clk_621;
+	subclk->which = which;
+
+	init.ops = &zynq_cpu_subclk_ops;
+	init.parent_names = &np->name;
+	init.num_parents = 1;
+
+	subclk->hw.init = &init;
+
+	clk = clk_register(NULL, &subclk->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		goto err_clk_register;
+
+	return clk;
+
+err_clk_register:
+	kfree(subclk);
+err_subclk_alloc:
+err_read_output_name:
+	return ERR_PTR(-EINVAL);
+}
+
+static void __init zynq_cpu_clk_setup(struct device_node *np)
+{
+	struct zynq_cpu_clk *cpuclk;
+	const char *parent_names[3];
+	struct clk_init_data init;
+	void __iomem *clk_621;
+	struct clk *clk;
+	u32 reg[2];
+	int err;
+	int i;
+
+	err = of_property_read_u32_array(np, "reg", reg, ARRAY_SIZE(reg));
+	if (WARN_ON(err))
+		return;
+
+	cpuclk = kzalloc(sizeof(*cpuclk), GFP_KERNEL);
+	if (WARN_ON(!cpuclk))
+		return;
+
+	cpuclk->clk_ctrl = slcr_base + reg[0];
+	clk_621 = slcr_base + reg[1];
+	spin_lock_init(&cpuclk->clkact_lock);
+
+	init.name = np->name;
+	init.ops = &zynq_cpu_clk_ops;
+	for (i = 0; i < ARRAY_SIZE(parent_names); i++)
+		parent_names[i] = of_clk_get_parent_name(np, i);
+	init.parent_names = parent_names;
+	init.num_parents = ARRAY_SIZE(parent_names);
+
+	cpuclk->hw.init = &init;
+
+	clk = clk_register(NULL, &cpuclk->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return;
+
+	err = of_clk_add_provider(np, of_clk_src_simple_get, clk);
+	if (WARN_ON(err))
+		return;
+
+	for (i = 0; i < 4; i++) {
+		cpuclk->subclks[i] = zynq_cpu_subclk_setup(np, i, clk_621);
+		if (WARN_ON(IS_ERR(cpuclk->subclks[i])))
+			return;
+	}
+
+	cpuclk->onecell_data.clks = cpuclk->subclks;
+	cpuclk->onecell_data.clk_num = i;
+
+	err = of_clk_add_provider(np, of_clk_src_onecell_get,
+				  &cpuclk->onecell_data);
+	if (WARN_ON(err))
+		return;
+}
+
+static const __initconst struct of_device_id zynq_clk_match[] = {
+	{ .compatible = "fixed-clock", .data = of_fixed_clk_setup, },
+	{ .compatible = "xlnx,zynq-pll", .data = zynq_pll_clk_setup, },
+	{ .compatible = "xlnx,zynq-periph-clock",
+		.data = zynq_periph_clk_setup, },
+	{ .compatible = "xlnx,zynq-cpu-clock", .data = zynq_cpu_clk_setup, },
+	{}
+};
+
+void __init xilinx_zynq_clocks_init(void __iomem *slcr)
+{
+	slcr_base = slcr;
+	of_clk_init(zynq_clk_match);
+}

include/linux/clk/zynq.h

+/*
+ * Copyright (C) 2012 National Instruments
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __LINUX_CLK_ZYNQ_H_
+#define __LINUX_CLK_ZYNQ_H_
+
+void __init xilinx_zynq_clocks_init(void __iomem *slcr);
+
+#endif