Blackfin: ad7160eval: new board port

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

arch/blackfin/Kconfig

@@ -356,7 +356,7 @@ config MEM_MT48LC8M32B2B5_7
 
 config MEM_MT48LC32M16A2TG_75
 	bool
-	depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP)
+	depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP || BFIN527_AD7160EVAL)
 	default y
 
 config MEM_MT48H32M16LFCJ_75
@@ -426,6 +426,7 @@ config CLKIN_HZ
 	default "25000000" # most people use this
 	default "27000000" if BFIN533_EZKIT
 	default "30000000" if BFIN561_EZKIT
+	default "24000000" if BFIN527_AD7160EVAL
 	help
 	  The frequency of CLKIN crystal oscillator on the board in Hz.
 	  Warning: This value should match the crystal on the board. Otherwise,
@@ -463,6 +464,7 @@ config VCO_MULT
 	default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT
 	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
+	default "25" if BFIN527_AD7160EVAL
 	help
 	  This controls the frequency of the on-chip PLL. This can be between 1 and 64.
 	  PLL Frequency = (Crystal Frequency) * (this setting)

arch/blackfin/configs/BF527-AD7160-EVAL_defconfig

+CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_EMBEDDED=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_AIO is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_PREEMPT=y
+CONFIG_BF527=y
+CONFIG_BF_REV_0_2=y
+CONFIG_IRQ_TWI=7
+CONFIG_IRQ_PORTH_INTA=7
+CONFIG_IRQ_PORTH_INTB=7
+CONFIG_BFIN527_AD7160EVAL=y
+CONFIG_BF527_SPORT0_PORTF=y
+CONFIG_BF527_UART1_PORTG=y
+CONFIG_IRQ_USB_INT0=11
+CONFIG_IRQ_USB_INT1=11
+CONFIG_IRQ_USB_INT2=11
+CONFIG_IRQ_USB_DMA=11
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="bootargs=root=/dev/mtdblock0 rw clkin_hz=24000000 earlyprintk=serial,uart0,57600 console=tty0 console=ttyBF0,57600"
+CONFIG_CLKIN_HZ=24000000
+CONFIG_HZ_300=y
+# CONFIG_CYCLES_CLOCKSOURCE is not set
+CONFIG_IP_CHECKSUM_L1=y
+CONFIG_SYSCALL_TAB_L1=y
+CONFIG_CPLB_SWITCH_TAB_L1=y
+CONFIG_BFIN_GPTIMERS=y
+CONFIG_C_CDPRIO=y
+CONFIG_BANK_1=0x5554
+CONFIG_BANK_3=0xFFC0
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_ZFLAT=y
+CONFIG_NET=y
+CONFIG_UNIX=y
+# CONFIG_WIRELESS is not set
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_AD7160=y
+CONFIG_TOUCHSCREEN_AD7160_FW=y
+# CONFIG_SERIO is not set
+# CONFIG_BFIN_DMA_INTERFACE is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_BFIN=y
+CONFIG_SERIAL_BFIN_CONSOLE=y
+CONFIG_SERIAL_BFIN_UART0=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_BFIN_OTP is not set
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+# CONFIG_I2C_HELPER_AUTO is not set
+CONFIG_I2C_ALGOBIT=y
+CONFIG_I2C_BLACKFIN_TWI=y
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=400
+CONFIG_SPI=y
+CONFIG_SPI_BFIN=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_LOGO_BLACKFIN_VGA16 is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VBUS_DRAW=500
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_SPI=y
+CONFIG_EXT2_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
+CONFIG_CPLB_INFO=y
+CONFIG_SECURITY=y
+CONFIG_CRC_CCITT=m

arch/blackfin/mach-bf527/boards/Kconfig

@@ -24,4 +24,9 @@ config BFIN526_EZBRD
 	help
 	  BF526-EZBRD/EZKIT Lite board support.
 
+config BFIN527_AD7160EVAL
+	bool "BF527-AD7160-EVAL"
+	help
+	  BF527-AD7160-EVAL board support.
+
 endchoice

arch/blackfin/mach-bf527/boards/Makefile

@@ -6,3 +6,4 @@ obj-$(CONFIG_BFIN527_EZKIT)            += ezkit.o
 obj-$(CONFIG_BFIN527_EZKIT_V2)         += ezkit.o
 obj-$(CONFIG_BFIN527_BLUETECHNIX_CM)   += cm_bf527.o
 obj-$(CONFIG_BFIN526_EZBRD)            += ezbrd.o
+obj-$(CONFIG_BFIN527_AD7160EVAL)       += ad7160eval.o