Skip to content

L
linux
Commit 94314a40 authored by Arnd Bergmann's avatar Arnd Bergmann
Browse files
Options

Merge branch 'dt/gic' into imx/imx6q

parents 929f58ae f37a53cc
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 1177 additions and 1513 deletions
Documentation/devicetree/bindings/arm/gic.txt 0 → 100644
View file @ 94314a40
* ARM Generic Interrupt Controller
ARM SMP cores are often associated with a GIC, providing per processor
interrupts (PPI), shared processor interrupts (SPI) and software
generated interrupts (SGI).
Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
Secondary GICs are cascaded into the upward interrupt controller and do not
have PPIs or SGIs.
Main node required properties:
- compatible : should be one of:
"arm,cortex-a9-gic"
"arm,arm11mp-gic"
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Specifies the number of cells needed to encode an
interrupt source. The type shall be a <u32> and the value shall be 3.
The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
interrupts.
The 2nd cell contains the interrupt number for the interrupt type.
SPI interrupts are in the range [0-987]. PPI interrupts are in the
range [0-15].
The 3rd cell is the flags, encoded as follows:
bits[3:0] trigger type and level flags.
1 = low-to-high edge triggered
2 = high-to-low edge triggered
4 = active high level-sensitive
8 = active low level-sensitive
bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of
the 8 possible cpus attached to the GIC. A bit set to '1' indicated
the interrupt is wired to that CPU. Only valid for PPI interrupts.
- reg : Specifies base physical address(s) and size of the GIC registers. The
first region is the GIC distributor register base and size. The 2nd region is
the GIC cpu interface register base and size.
Optional
- interrupts : Interrupt source of the parent interrupt controller. Only
present on secondary GICs.
Example:
intc: interrupt-controller@fff11000 {
compatible = "arm,cortex-a9-gic";
#interrupt-cells = <3>;
#address-cells = <1>;
interrupt-controller;
reg = <0xfff11000 0x1000>,
<0xfff10100 0x100>;
};
arch/arm/Kconfig
View file @ 94314a40
......@@ -196,7 +196,8 @@ config VECTORS_BASE
The base address of exception vectors.
config ARM_PATCH_PHYS_VIRT
bool "Patch physical to virtual translations at runtime"
bool "Patch physical to virtual translations at runtime" if EMBEDDED
default y
depends on !XIP_KERNEL && MMU
depends on !ARCH_REALVIEW || !SPARSEMEM
help
......@@ -205,16 +206,25 @@ config ARM_PATCH_PHYS_VIRT
kernel in system memory.
This can only be used with non-XIP MMU kernels where the base
of physical memory is at a 16MB boundary, or theoretically 64K
for the MSM machine class.
of physical memory is at a 16MB boundary.
config ARM_PATCH_PHYS_VIRT_16BIT
def_bool y
depends on ARM_PATCH_PHYS_VIRT && ARCH_MSM
Only disable this option if you know that you do not require
this feature (eg, building a kernel for a single machine) and
you need to shrink the kernel to the minimal size.
config NEED_MACH_MEMORY_H
bool
help
Select this when mach/memory.h is required to provide special
definitions for this platform. The need for mach/memory.h should
be avoided when possible.
config PHYS_OFFSET
hex "Physical address of main memory"
depends on !ARM_PATCH_PHYS_VIRT && !NEED_MACH_MEMORY_H
help
This option extends the physical to virtual translation patching
to allow physical memory down to a theoretical minimum of 64K
boundaries.
Please provide the physical address corresponding to the
location of main memory in your system.
source "init/Kconfig"
......@@ -247,6 +257,7 @@ config ARCH_INTEGRATOR
select GENERIC_CLOCKEVENTS
select PLAT_VERSATILE
select PLAT_VERSATILE_FPGA_IRQ
select NEED_MACH_MEMORY_H
help
Support for ARM's Integrator platform.
......@@ -262,6 +273,7 @@ config ARCH_REALVIEW
select PLAT_VERSATILE_CLCD
select ARM_TIMER_SP804
select GPIO_PL061 if GPIOLIB
select NEED_MACH_MEMORY_H
help
This enables support for ARM Ltd RealView boards.
......@@ -302,7 +314,6 @@ config ARCH_AT91
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
select CLKDEV_LOOKUP
select ARM_PATCH_PHYS_VIRT if MMU
help
This enables support for systems based on the Atmel AT91RM9200,
AT91SAM9 and AT91CAP9 processors.
......@@ -323,6 +334,7 @@ config ARCH_CLPS711X
bool "Cirrus Logic CLPS711x/EP721x-based"
select CPU_ARM720T
select ARCH_USES_GETTIMEOFFSET
select NEED_MACH_MEMORY_H
help
Support for Cirrus Logic 711x/721x based boards.
......@@ -363,6 +375,7 @@ config ARCH_EBSA110
select ISA
select NO_IOPORT
select ARCH_USES_GETTIMEOFFSET
select NEED_MACH_MEMORY_H
help
This is an evaluation board for the StrongARM processor available
from Digital. It has limited hardware on-board, including an
......@@ -378,6 +391,7 @@ config ARCH_EP93XX
select ARCH_REQUIRE_GPIOLIB
select ARCH_HAS_HOLES_MEMORYMODEL
select ARCH_USES_GETTIMEOFFSET
select NEED_MEMORY_H
help
This enables support for the Cirrus EP93xx series of CPUs.
......@@ -386,6 +400,7 @@ config ARCH_FOOTBRIDGE
select CPU_SA110
select FOOTBRIDGE
select GENERIC_CLOCKEVENTS
select NEED_MACH_MEMORY_H
help
Support for systems based on the DC21285 companion chip
("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
......@@ -435,6 +450,7 @@ config ARCH_IOP13XX
select PCI
select ARCH_SUPPORTS_MSI
select VMSPLIT_1G
select NEED_MACH_MEMORY_H
help
Support for Intel's IOP13XX (XScale) family of processors.
......@@ -465,6 +481,7 @@ config ARCH_IXP23XX
select CPU_XSC3
select PCI
select ARCH_USES_GETTIMEOFFSET
select NEED_MACH_MEMORY_H
help
Support for Intel's IXP23xx (XScale) family of processors.
......@@ -474,6 +491,7 @@ config ARCH_IXP2000
select CPU_XSCALE
select PCI
select ARCH_USES_GETTIMEOFFSET
select NEED_MACH_MEMORY_H
help
Support for Intel's IXP2400/2800 (XScale) family of processors.
......@@ -567,6 +585,7 @@ config ARCH_KS8695
select CPU_ARM922T
select ARCH_REQUIRE_GPIOLIB
select ARCH_USES_GETTIMEOFFSET
select NEED_MACH_MEMORY_H
help
Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
System-on-Chip devices.
......@@ -658,6 +677,7 @@ config ARCH_SHMOBILE
select SPARSE_IRQ
select MULTI_IRQ_HANDLER
select PM_GENERIC_DOMAINS if PM
select NEED_MACH_MEMORY_H
help
Support for Renesas's SH-Mobile and R-Mobile ARM platforms.
......@@ -672,6 +692,7 @@ config ARCH_RPC
select NO_IOPORT
select ARCH_SPARSEMEM_ENABLE
select ARCH_USES_GETTIMEOFFSET
select NEED_MACH_MEMORY_H
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
......@@ -690,6 +711,7 @@ config ARCH_SA1100
select HAVE_SCHED_CLOCK
select TICK_ONESHOT
select ARCH_REQUIRE_GPIOLIB
select NEED_MACH_MEMORY_H
help
Support for StrongARM 11x0 based boards.
......@@ -782,6 +804,7 @@ config ARCH_S5PV210
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C_RTC if RTC_CLASS
select HAVE_S3C2410_WATCHDOG if WATCHDOG
select NEED_MACH_MEMORY_H
help
Samsung S5PV210/S5PC110 series based systems
......@@ -798,6 +821,7 @@ config ARCH_EXYNOS4
select HAVE_S3C_RTC if RTC_CLASS
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C2410_WATCHDOG if WATCHDOG
select NEED_MACH_MEMORY_H
help
Samsung EXYNOS4 series based systems
......@@ -809,6 +833,7 @@ config ARCH_SHARK
select ZONE_DMA
select PCI
select ARCH_USES_GETTIMEOFFSET
select NEED_MACH_MEMORY_H
help
Support for the StrongARM based Digital DNARD machine, also known
as "Shark" (<http://www.shark-linux.de/shark.html>).
......@@ -836,6 +861,7 @@ config ARCH_U300
select CLKDEV_LOOKUP
select HAVE_MACH_CLKDEV
select GENERIC_GPIO
select NEED_MACH_MEMORY_H
help
Support for ST-Ericsson U300 series mobile platforms.
......
arch/arm/Makefile
View file @ 94314a40
......@@ -128,6 +128,9 @@ textofs-$(CONFIG_PM_H1940) := 0x00108000
ifeq ($(CONFIG_ARCH_SA1100),y)
textofs-$(CONFIG_SA1111) := 0x00208000
endif
textofs-$(CONFIG_ARCH_MSM7X30) := 0x00208000
textofs-$(CONFIG_ARCH_MSM8X60) := 0x00208000
textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
# Machine directory name. This list is sorted alphanumerically
# by CONFIG_* macro name.
......
arch/arm/common/Kconfig
View file @ 94314a40
config ARM_GIC
select IRQ_DOMAIN
bool
config ARM_VIC
......
arch/arm/common/gic.c
View file @ 94314a40
......@@ -24,11 +24,20 @@
*/
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/err.h>
#include <linux/export.h>
#include <linux/list.h>
#include <linux/smp.h>
#include <linux/cpu_pm.h>
#include <linux/cpumask.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/irqdomain.h>
#include <linux/interrupt.h>
#include <linux/percpu.h>
#include <linux/slab.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
......@@ -72,8 +81,7 @@ static inline void __iomem *gic_cpu_base(struct irq_data *d)
static inline unsigned int gic_irq(struct irq_data *d)
{
struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
return d->irq - gic_data->irq_offset;
return d->hwirq;
}
/*
......@@ -81,7 +89,7 @@ static inline unsigned int gic_irq(struct irq_data *d)
*/
static void gic_mask_irq(struct irq_data *d)
{
u32 mask = 1 << (d->irq % 32);
u32 mask = 1 << (gic_irq(d) % 32);
spin_lock(&irq_controller_lock);
writel_relaxed(mask, gic_dist_base(d) + GIC_DIST_ENABLE_CLEAR + (gic_irq(d) / 32) * 4);
......@@ -92,7 +100,7 @@ static void gic_mask_irq(struct irq_data *d)
static void gic_unmask_irq(struct irq_data *d)
{
u32 mask = 1 << (d->irq % 32);
u32 mask = 1 << (gic_irq(d) % 32);
spin_lock(&irq_controller_lock);
if (gic_arch_extn.irq_unmask)
......@@ -173,7 +181,7 @@ static int gic_set_affinity(struct irq_data *d, const struct cpumask *mask_val,
bool force)
{
void __iomem *reg = gic_dist_base(d) + GIC_DIST_TARGET + (gic_irq(d) & ~3);
unsigned int shift = (d->irq % 4) * 8;
unsigned int shift = (gic_irq(d) % 4) * 8;
unsigned int cpu = cpumask_any_and(mask_val, cpu_online_mask);
u32 val, mask, bit;
......@@ -224,7 +232,7 @@ static void gic_handle_cascade_irq(unsigned int irq, struct irq_desc *desc)
if (gic_irq == 1023)
goto out;
cascade_irq = gic_irq + chip_data->irq_offset;
cascade_irq = irq_domain_to_irq(&chip_data->domain, gic_irq);
if (unlikely(gic_irq < 32 || gic_irq > 1020 || cascade_irq >= NR_IRQS))
do_bad_IRQ(cascade_irq, desc);
else
......@@ -256,11 +264,12 @@ void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
irq_set_chained_handler(irq, gic_handle_cascade_irq);
}
static void __init gic_dist_init(struct gic_chip_data *gic,
unsigned int irq_start)
static void __init gic_dist_init(struct gic_chip_data *gic)
{
unsigned int gic_irqs, irq_limit, i;
unsigned int i, irq;
u32 cpumask;
unsigned int gic_irqs = gic->gic_irqs;
struct irq_domain *domain = &gic->domain;
void __iomem *base = gic->dist_base;
u32 cpu = 0;
......@@ -274,17 +283,6 @@ static void __init gic_dist_init(struct gic_chip_data *gic,
writel_relaxed(0, base + GIC_DIST_CTRL);
/*
* Find out how many interrupts are supported.
* The GIC only supports up to 1020 interrupt sources.
*/
gic_irqs = readl_relaxed(base + GIC_DIST_CTR) & 0x1f;
gic_irqs = (gic_irqs + 1) * 32;
if (gic_irqs > 1020)
gic_irqs = 1020;
gic->gic_irqs = gic_irqs;
/*
* Set all global interrupts to be level triggered, active low.
*/
......@@ -310,20 +308,21 @@ static void __init gic_dist_init(struct gic_chip_data *gic,
for (i = 32; i < gic_irqs; i += 32)
writel_relaxed(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
/*
* Limit number of interrupts registered to the platform maximum
*/
irq_limit = gic->irq_offset + gic_irqs;
if (WARN_ON(irq_limit > NR_IRQS))
irq_limit = NR_IRQS;
/*
* Setup the Linux IRQ subsystem.
*/
for (i = irq_start; i < irq_limit; i++) {
irq_set_chip_and_handler(i, &gic_chip, handle_fasteoi_irq);
irq_set_chip_data(i, gic);
set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
irq_domain_for_each_irq(domain, i, irq) {
if (i < 32) {
irq_set_percpu_devid(irq);
irq_set_chip_and_handler(irq, &gic_chip,
handle_percpu_devid_irq);
set_irq_flags(irq, IRQF_VALID | IRQF_NOAUTOEN);
} else {
irq_set_chip_and_handler(irq, &gic_chip,
handle_fasteoi_irq);
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
irq_set_chip_data(irq, gic);
}
writel_relaxed(1, base + GIC_DIST_CTRL);
......@@ -535,23 +534,85 @@ static void __init gic_pm_init(struct gic_chip_data *gic)
}
#endif
void __init gic_init(unsigned int gic_nr, unsigned int irq_start,
#ifdef CONFIG_OF
static int gic_irq_domain_dt_translate(struct irq_domain *d,
struct device_node *controller,
const u32 *intspec, unsigned int intsize,
unsigned long *out_hwirq, unsigned int *out_type)
{
if (d->of_node != controller)
return -EINVAL;
if (intsize < 3)
return -EINVAL;
/* Get the interrupt number and add 16 to skip over SGIs */
*out_hwirq = intspec[1] + 16;
/* For SPIs, we need to add 16 more to get the GIC irq ID number */
if (!intspec[0])
*out_hwirq += 16;
*out_type = intspec[2] & IRQ_TYPE_SENSE_MASK;
return 0;
}
#endif
const struct irq_domain_ops gic_irq_domain_ops = {
#ifdef CONFIG_OF
.dt_translate = gic_irq_domain_dt_translate,
#endif
};
void __init gic_init(unsigned int gic_nr, int irq_start,
void __iomem *dist_base, void __iomem *cpu_base)
{
struct gic_chip_data *gic;
struct irq_domain *domain;
int gic_irqs;
BUG_ON(gic_nr >= MAX_GIC_NR);
gic = &gic_data[gic_nr];
domain = &gic->domain;
gic->dist_base = dist_base;
gic->cpu_base = cpu_base;
gic->irq_offset = (irq_start - 1) & ~31;
if (gic_nr == 0)
/*
* For primary GICs, skip over SGIs.
* For secondary GICs, skip over PPIs, too.
*/
if (gic_nr == 0) {
gic_cpu_base_addr = cpu_base;
domain->hwirq_base = 16;
if (irq_start > 0)
irq_start = (irq_start & ~31) + 16;
} else
domain->hwirq_base = 32;
/*
* Find out how many interrupts are supported.
* The GIC only supports up to 1020 interrupt sources.
*/
gic_irqs = readl_relaxed(dist_base + GIC_DIST_CTR) & 0x1f;
gic_irqs = (gic_irqs + 1) * 32;
if (gic_irqs > 1020)
gic_irqs = 1020;
gic->gic_irqs = gic_irqs;
domain->nr_irq = gic_irqs - domain->hwirq_base;
domain->irq_base = irq_alloc_descs(irq_start, 16, domain->nr_irq,
numa_node_id());
if (IS_ERR_VALUE(domain->irq_base)) {
WARN(1, "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n",
irq_start);
domain->irq_base = irq_start;
}
domain->priv = gic;
domain->ops = &gic_irq_domain_ops;
irq_domain_add(domain);
gic_chip.flags |= gic_arch_extn.flags;
gic_dist_init(gic, irq_start);
gic_dist_init(gic);
gic_cpu_init(gic);
gic_pm_init(gic);
}
......@@ -563,16 +624,6 @@ void __cpuinit gic_secondary_init(unsigned int gic_nr)
gic_cpu_init(&gic_data[gic_nr]);
}
void __cpuinit gic_enable_ppi(unsigned int irq)
{
unsigned long flags;
local_irq_save(flags);
irq_set_status_flags(irq, IRQ_NOPROBE);
gic_unmask_irq(irq_get_irq_data(irq));
local_irq_restore(flags);
}
#ifdef CONFIG_SMP
void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
{
......@@ -593,3 +644,35 @@ void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
writel_relaxed(map << 16 | irq, gic_data[0].dist_base + GIC_DIST_SOFTINT);
}
#endif
#ifdef CONFIG_OF
static int gic_cnt __initdata = 0;
int __init gic_of_init(struct device_node *node, struct device_node *parent)
{
void __iomem *cpu_base;
void __iomem *dist_base;
int irq;
struct irq_domain *domain = &gic_data[gic_cnt].domain;
if (WARN_ON(!node))
return -ENODEV;
dist_base = of_iomap(node, 0);
WARN(!dist_base, "unable to map gic dist registers\n");
cpu_base = of_iomap(node, 1);
WARN(!cpu_base, "unable to map gic cpu registers\n");
domain->of_node = of_node_get(node);
gic_init(gic_cnt, -1, dist_base, cpu_base);
if (parent) {
irq = irq_of_parse_and_map(node, 0);
gic_cascade_irq(gic_cnt, irq);
}
gic_cnt++;
return 0;
}
#endif
arch/arm/include/asm/entry-macro-multi.S
View file @ 94314a40
......@@ -25,13 +25,6 @@
movne r1, sp
adrne lr, BSYM(1b)
bne do_IPI
#ifdef CONFIG_LOCAL_TIMERS
test_for_ltirq r0, r2, r6, lr
movne r0, sp
adrne lr, BSYM(1b)
bne do_local_timer
#endif
#endif
9997:
.endm
......
arch/arm/include/asm/hardirq.h
View file @ 94314a40
......@@ -9,9 +9,6 @@
typedef struct {
unsigned int __softirq_pending;
#ifdef CONFIG_LOCAL_TIMERS
unsigned int local_timer_irqs;
#endif
#ifdef CONFIG_SMP
unsigned int ipi_irqs[NR_IPI];
#endif
......
arch/arm/include/asm/hardware/entry-macro-gic.S
View file @ 94314a40
......@@ -22,15 +22,11 @@
* interrupt controller spec. To wit:
*
* Interrupts 0-15 are IPI
* 16-28 are reserved
* 29-31 are local. We allow 30 to be used for the watchdog.
* 16-31 are local. We allow 30 to be used for the watchdog.
* 32-1020 are global
* 1021-1022 are reserved
* 1023 is "spurious" (no interrupt)
*
* For now, we ignore all local interrupts so only return an interrupt if it's
* between 30 and 1020. The test_for_ipi routine below will pick up on IPIs.
*
* A simple read from the controller will tell us the number of the highest
* priority enabled interrupt. We then just need to check whether it is in the
* valid range for an IRQ (30-1020 inclusive).
......@@ -43,7 +39,7 @@
ldr \tmp, =1021
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #29
cmp \irqnr, #15
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
......@@ -62,14 +58,3 @@
strcc \irqstat, [\base, #GIC_CPU_EOI]
cmpcs \irqnr, \irqnr
.endm
/* As above, this assumes that irqstat and base are preserved.. */
.macro test_for_ltirq, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
mov \tmp, #0
cmp \irqnr, #29
moveq \tmp, #1
streq \irqstat, [\base, #GIC_CPU_EOI]
cmp \tmp, #0
.endm
arch/arm/include/asm/hardware/gic.h
View file @ 94314a40
......@@ -33,17 +33,19 @@
#define GIC_DIST_SOFTINT 0xf00
#ifndef __ASSEMBLY__
#include <linux/irqdomain.h>
struct device_node;
extern void __iomem *gic_cpu_base_addr;
extern struct irq_chip gic_arch_extn;
void gic_init(unsigned int, unsigned int, void __iomem *, void __iomem *);
void gic_init(unsigned int, int, void __iomem *, void __iomem *);
int gic_of_init(struct device_node *node, struct device_node *parent);
void gic_secondary_init(unsigned int);
void gic_cascade_irq(unsigned int gic_nr, unsigned int irq);
void gic_raise_softirq(const struct cpumask *mask, unsigned int irq);
void gic_enable_ppi(unsigned int);
struct gic_chip_data {
unsigned int irq_offset;
void __iomem *dist_base;
void __iomem *cpu_base;
#ifdef CONFIG_CPU_PM
......@@ -52,6 +54,9 @@ struct gic_chip_data {
u32 saved_spi_target[DIV_ROUND_UP(1020, 4)];
u32 __percpu *saved_ppi_enable;
u32 __percpu *saved_ppi_conf;
#endif
#ifdef CONFIG_IRQ_DOMAIN
struct irq_domain domain;
#endif
unsigned int gic_irqs;
};
......
arch/arm/include/asm/localtimer.h
View file @ 94314a40
......@@ -10,6 +10,8 @@
#ifndef __ASM_ARM_LOCALTIMER_H
#define __ASM_ARM_LOCALTIMER_H
#include <linux/interrupt.h>
struct clock_event_device;
/*
......@@ -17,31 +19,20 @@ struct clock_event_device;
*/
void percpu_timer_setup(void);
/*
* Called from assembly, this is the local timer IRQ handler
*/
asmlinkage void do_local_timer(struct pt_regs *);
/*
* Called from C code
*/
void handle_local_timer(struct pt_regs *);
#ifdef CONFIG_LOCAL_TIMERS
#ifdef CONFIG_HAVE_ARM_TWD
#include "smp_twd.h"
#define local_timer_ack() twd_timer_ack()
#define local_timer_stop(c) twd_timer_stop((c))
#else
/*
* Platform provides this to acknowledge a local timer IRQ.
* Returns true if the local timer IRQ is to be processed.
* Stop the local timer
*/
int local_timer_ack(void);
void local_timer_stop(struct clock_event_device *);
#endif
......@@ -56,6 +47,10 @@ static inline int local_timer_setup(struct clock_event_device *evt)
{
return -ENXIO;
}
static inline void local_timer_stop(struct clock_event_device *evt)
{
}
#endif
#endif
arch/arm/include/asm/memory.h
View file @ 94314a40
......@@ -16,9 +16,12 @@
#include <linux/compiler.h>
#include <linux/const.h>
#include <linux/types.h>
#include <mach/memory.h>
#include <asm/sizes.h>
#ifdef CONFIG_NEED_MACH_MEMORY_H
#include <mach/memory.h>
#endif
/*
* Allow for constants defined here to be used from assembly code
* by prepending the UL suffix only with actual C code compilation.
......@@ -151,7 +154,6 @@
* so that all we need to do is modify the 8-bit constant field.
*/
#define __PV_BITS_31_24 0x81000000
#define __PV_BITS_23_16 0x00810000
extern unsigned long __pv_phys_offset;
#define PHYS_OFFSET __pv_phys_offset
......@@ -169,9 +171,6 @@ static inline unsigned long __virt_to_phys(unsigned long x)
{
unsigned long t;
__pv_stub(x, t, "add", __PV_BITS_31_24);
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
__pv_stub(t, t, "add", __PV_BITS_23_16);
#endif
return t;
}
......@@ -179,9 +178,6 @@ static inline unsigned long __phys_to_virt(unsigned long x)
{
unsigned long t;
__pv_stub(x, t, "sub", __PV_BITS_31_24);
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
__pv_stub(t, t, "sub", __PV_BITS_23_16);
#endif
return t;
}
#else
......@@ -191,7 +187,11 @@ static inline unsigned long __phys_to_virt(unsigned long x)
#endif
#ifndef PHYS_OFFSET
#ifdef PLAT_PHYS_OFFSET
#define PHYS_OFFSET PLAT_PHYS_OFFSET
#else
#define PHYS_OFFSET UL(CONFIG_PHYS_OFFSET)
#endif
#endif
/*
......
arch/arm/include/asm/module.h
View file @ 94314a40
......@@ -31,11 +31,7 @@ struct mod_arch_specific {
/* Add __virt_to_phys patching state as well */
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
#define MODULE_ARCH_VERMAGIC_P2V "p2v16 "
#else
#define MODULE_ARCH_VERMAGIC_P2V "p2v8 "
#endif
#else
#define MODULE_ARCH_VERMAGIC_P2V ""
#endif
......
arch/arm/include/asm/smp.h
View file @ 94314a40
......@@ -99,9 +99,4 @@ extern void platform_cpu_enable(unsigned int cpu);
extern void arch_send_call_function_single_ipi(int cpu);
extern void arch_send_call_function_ipi_mask(const struct cpumask *mask);
/*
* show local interrupt info
*/
extern void show_local_irqs(struct seq_file *, int);
#endif /* ifndef __ASM_ARM_SMP_H */
arch/arm/include/asm/smp_twd.h
View file @ 94314a40
......@@ -22,7 +22,7 @@ struct clock_event_device;
extern void __iomem *twd_base;
int twd_timer_ack(void);
void twd_timer_setup(struct clock_event_device *);
void twd_timer_stop(struct clock_event_device *);
#endif
arch/arm/kernel/debug.S
View file @ 94314a40
......@@ -22,7 +22,7 @@
#if defined(CONFIG_DEBUG_ICEDCC)
@@ debug using ARM EmbeddedICE DCC channel
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
.endm
#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_V6K) || defined(CONFIG_CPU_V7)
......@@ -106,7 +106,7 @@
#ifdef CONFIG_MMU
.macro addruart_current, rx, tmp1, tmp2
addruart \tmp1, \tmp2
addruart \tmp1, \tmp2, \rx
mrc p15, 0, \rx, c1, c0
tst \rx, #1
moveq \rx, \tmp1
......
arch/arm/kernel/head.S
View file @ 94314a40
......@@ -95,7 +95,7 @@ ENTRY(stext)
sub r4, r3, r4 @ (PHYS_OFFSET - PAGE_OFFSET)
add r8, r8, r4 @ PHYS_OFFSET
#else
ldr r8, =PLAT_PHYS_OFFSET
ldr r8, =PHYS_OFFSET @ always constant in this case
#endif
/*
......@@ -234,7 +234,7 @@ __create_page_tables:
* This allows debug messages to be output
* via a serial console before paging_init.
*/
addruart r7, r3
addruart r7, r3, r0
mov r3, r3, lsr #20
mov r3, r3, lsl #2
......@@ -488,13 +488,8 @@ __fixup_pv_table:
add r5, r5, r3 @ adjust table end address
add r7, r7, r3 @ adjust __pv_phys_offset address
str r8, [r7] @ save computed PHYS_OFFSET to __pv_phys_offset
#ifndef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
mov r6, r3, lsr #24 @ constant for add/sub instructions
teq r3, r6, lsl #24 @ must be 16MiB aligned
#else
mov r6, r3, lsr #16 @ constant for add/sub instructions
teq r3, r6, lsl #16 @ must be 64kiB aligned
#endif
THUMB( it ne @ cross section branch )
bne __error
str r6, [r7, #4] @ save to __pv_offset
......@@ -510,20 +505,8 @@ ENDPROC(__fixup_pv_table)
.text
__fixup_a_pv_table:
#ifdef CONFIG_THUMB2_KERNEL
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
lsls r0, r6, #24
lsr r6, #8
beq 1f
clz r7, r0
lsr r0, #24
lsl r0, r7
bic r0, 0x0080
lsrs r7, #1
orrcs r0, #0x0080
orr r0, r0, r7, lsl #12
#endif
1: lsls r6, #24
beq 4f
lsls r6, #24
beq 2f
clz r7, r6
lsr r6, #24
lsl r6, r7
......@@ -532,43 +515,25 @@ __fixup_a_pv_table:
orrcs r6, #0x0080
orr r6, r6, r7, lsl #12
orr r6, #0x4000
b 4f
2: @ at this point the C flag is always clear
add r7, r3
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
ldrh ip, [r7]
tst ip, 0x0400 @ the i bit tells us LS or MS byte
beq 3f
cmp r0, #0 @ set C flag, and ...
biceq ip, 0x0400 @ immediate zero value has a special encoding
streqh ip, [r7] @ that requires the i bit cleared
#endif
3: ldrh ip, [r7, #2]
b 2f
1: add r7, r3
ldrh ip, [r7, #2]
and ip, 0x8f00
orrcc ip, r6 @ mask in offset bits 31-24
orrcs ip, r0 @ mask in offset bits 23-16
orr ip, r6 @ mask in offset bits 31-24
strh ip, [r7, #2]
4: cmp r4, r5
2: cmp r4, r5
ldrcc r7, [r4], #4 @ use branch for delay slot
bcc 2b
bcc 1b
bx lr
#else
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
and r0, r6, #255 @ offset bits 23-16
mov r6, r6, lsr #8 @ offset bits 31-24
#else
mov r0, #0 @ just in case...
#endif
b 3f
2: ldr ip, [r7, r3]
b 2f
1: ldr ip, [r7, r3]
bic ip, ip, #0x000000ff
tst ip, #0x400 @ rotate shift tells us LS or MS byte
orrne ip, ip, r6 @ mask in offset bits 31-24
orreq ip, ip, r0 @ mask in offset bits 23-16
orr ip, ip, r6 @ mask in offset bits 31-24
str ip, [r7, r3]
3: cmp r4, r5
2: cmp r4, r5
ldrcc r7, [r4], #4 @ use branch for delay slot
bcc 2b
bcc 1b
mov pc, lr
#endif
ENDPROC(__fixup_a_pv_table)
......
arch/arm/kernel/irq.c
View file @ 94314a40
......@@ -58,9 +58,6 @@ int arch_show_interrupts(struct seq_file *p, int prec)
#endif
#ifdef CONFIG_SMP
show_ipi_list(p, prec);
#endif
#ifdef CONFIG_LOCAL_TIMERS
show_local_irqs(p, prec);
#endif
seq_printf(p, "%*s: %10lu\n", prec, "Err", irq_err_count);
return 0;
......
arch/arm/kernel/smp.c
View file @ 94314a40
......@@ -457,10 +457,6 @@ u64 smp_irq_stat_cpu(unsigned int cpu)
for (i = 0; i < NR_IPI; i++)
sum += __get_irq_stat(cpu, ipi_irqs[i]);
#ifdef CONFIG_LOCAL_TIMERS
sum += __get_irq_stat(cpu, local_timer_irqs);
#endif
return sum;
}
......@@ -477,38 +473,6 @@ static void ipi_timer(void)
irq_exit();
}
#ifdef CONFIG_LOCAL_TIMERS
asmlinkage void __exception_irq_entry do_local_timer(struct pt_regs *regs)
{
handle_local_timer(regs);
}
void handle_local_timer(struct pt_regs *regs)
{
struct pt_regs *old_regs = set_irq_regs(regs);
int cpu = smp_processor_id();
if (local_timer_ack()) {
__inc_irq_stat(cpu, local_timer_irqs);
ipi_timer();
}
set_irq_regs(old_regs);
}
void show_local_irqs(struct seq_file *p, int prec)
{
unsigned int cpu;
seq_printf(p, "%*s: ", prec, "LOC");
for_each_present_cpu(cpu)
seq_printf(p, "%10u ", __get_irq_stat(cpu, local_timer_irqs));
seq_printf(p, " Local timer interrupts\n");
}
#endif
#ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
static void smp_timer_broadcast(const struct cpumask *mask)
{
......@@ -559,7 +523,7 @@ static void percpu_timer_stop(void)
unsigned int cpu = smp_processor_id();
struct clock_event_device *evt = &per_cpu(percpu_clockevent, cpu);
evt->set_mode(CLOCK_EVT_MODE_UNUSED, evt);
local_timer_stop(evt);
}
#endif
......
arch/arm/kernel/smp_twd.c
View file @ 94314a40
......@@ -19,6 +19,7 @@
#include <linux/io.h>
#include <asm/smp_twd.h>
#include <asm/localtimer.h>
#include <asm/hardware/gic.h>
/* set up by the platform code */
......@@ -26,6 +27,8 @@ void __iomem *twd_base;
static unsigned long twd_timer_rate;
static struct clock_event_device __percpu **twd_evt;
static void twd_set_mode(enum clock_event_mode mode,
struct clock_event_device *clk)
{
......@@ -80,6 +83,12 @@ int twd_timer_ack(void)
return 0;
}
void twd_timer_stop(struct clock_event_device *clk)
{
twd_set_mode(CLOCK_EVT_MODE_UNUSED, clk);
disable_percpu_irq(clk->irq);
}
static void __cpuinit twd_calibrate_rate(void)
{
unsigned long count;
......@@ -119,11 +128,43 @@ static void __cpuinit twd_calibrate_rate(void)
}
}
static irqreturn_t twd_handler(int irq, void *dev_id)
{
struct clock_event_device *evt = *(struct clock_event_device **)dev_id;
if (twd_timer_ack()) {
evt->event_handler(evt);
return IRQ_HANDLED;
}
return IRQ_NONE;
}
/*
* Setup the local clock events for a CPU.
*/
void __cpuinit twd_timer_setup(struct clock_event_device *clk)
{
struct clock_event_device **this_cpu_clk;
if (!twd_evt) {
int err;
twd_evt = alloc_percpu(struct clock_event_device *);
if (!twd_evt) {
pr_err("twd: can't allocate memory\n");
return;
}
err = request_percpu_irq(clk->irq, twd_handler,
"twd", twd_evt);
if (err) {
pr_err("twd: can't register interrupt %d (%d)\n",
clk->irq, err);
return;
}
}
twd_calibrate_rate();
clk->name = "local_timer";
......@@ -137,8 +178,10 @@ void __cpuinit twd_timer_setup(struct clock_event_device *clk)
clk->max_delta_ns = clockevent_delta2ns(0xffffffff, clk);
clk->min_delta_ns = clockevent_delta2ns(0xf, clk);
this_cpu_clk = __this_cpu_ptr(twd_evt);
*this_cpu_clk = clk;
clockevents_register_device(clk);
/* Make sure our local interrupt controller has this enabled */
gic_enable_ppi(clk->irq);
enable_percpu_irq(clk->irq, 0);
}
arch/arm/mach-at91/include/mach/debug-macro.S
View file @ 94314a40
......@@ -14,7 +14,7 @@
#include <mach/hardware.h>
#include <mach/at91_dbgu.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =(AT91_BASE_SYS + AT91_DBGU) @ System peripherals (phys address)
ldr \rv, =(AT91_VA_BASE_SYS + AT91_DBGU) @ System peripherals (virt address)
.endm
......
arch/arm/mach-bcmring/include/mach/hardware.h
View file @ 94314a40
......@@ -22,7 +22,6 @@
#define __ASM_ARCH_HARDWARE_H
#include <asm/sizes.h>
#include <mach/memory.h>
#include <cfg_global.h>
#include <mach/csp/mm_io.h>
......@@ -31,7 +30,7 @@
* *_SIZE is the size of the region
* *_BASE is the virtual address
*/
#define RAM_START PLAT_PHYS_OFFSET
#define RAM_START PHYS_OFFSET
#define RAM_SIZE (CFG_GLOBAL_RAM_SIZE-CFG_GLOBAL_RAM_SIZE_RESERVED)
#define RAM_BASE PAGE_OFFSET
......
arch/arm/mach-bcmring/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*****************************************************************************
* Copyright 2005 - 2008 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#include <cfg_global.h>
/*
* Physical vs virtual RAM address space conversion. These are
* private definitions which should NOT be used outside memory.h
* files. Use virt_to_phys/phys_to_virt/__pa/__va instead.
*/
#define PLAT_PHYS_OFFSET CFG_GLOBAL_RAM_BASE
#endif
arch/arm/mach-clps711x/include/mach/debug-macro.S
View file @ 94314a40
......@@ -14,7 +14,7 @@
#include <mach/hardware.h>
#include <asm/hardware/clps7111.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
#ifndef CONFIG_DEBUG_CLPS711X_UART2
mov \rp, #0x0000 @ UART1
#else
......
arch/arm/mach-cns3xxx/include/mach/debug-macro.S
View file @ 94314a40
......@@ -10,7 +10,7 @@
* published by the Free Software Foundation.
*/
.macro addruart,rp,rv
.macro addruart,rp,rv,tmp
mov \rp, #0x00009000
orr \rv, \rp, #0xf0000000 @ virtual base
orr \rp, \rp, #0x10000000
......
arch/arm/mach-cns3xxx/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* Copyright 2003 ARM Limited
* Copyright 2008 Cavium Networks
*
* This file is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License, Version 2, as
* published by the Free Software Foundation.
*/
#ifndef __MACH_MEMORY_H
#define __MACH_MEMORY_H
/*
* Physical DRAM offset.
*/
#define PLAT_PHYS_OFFSET UL(0x00000000)
#define __phys_to_bus(x) ((x) + PHYS_OFFSET)
#define __bus_to_phys(x) ((x) - PHYS_OFFSET)
#define __virt_to_bus(v) __phys_to_bus(__virt_to_phys(v))
#define __bus_to_virt(b) __phys_to_virt(__bus_to_phys(b))
#define __pfn_to_bus(p) __phys_to_bus(__pfn_to_phys(p))
#define __bus_to_pfn(b) __phys_to_pfn(__bus_to_phys(b))
#endif
arch/arm/mach-davinci/cpuidle.c
View file @ 94314a40
......@@ -19,7 +19,7 @@
#include <asm/proc-fns.h>
#include <mach/cpuidle.h>
#include <mach/memory.h>
#include <mach/ddr2.h>
#define DAVINCI_CPUIDLE_MAX_STATES 2
......
arch/arm/mach-davinci/include/mach/ddr2.h 0 → 100644
View file @ 94314a40
#define DDR2_SDRCR_OFFSET 0xc
#define DDR2_SRPD_BIT (1 << 23)
#define DDR2_MCLKSTOPEN_BIT (1 << 30)
#define DDR2_LPMODEN_BIT (1 << 31)
arch/arm/mach-davinci/include/mach/debug-macro.S
View file @ 94314a40
......@@ -18,56 +18,50 @@
#include <linux/serial_reg.h>
#include <asm/memory.h>
#include <mach/serial.h>
#define UART_SHIFT 2
#define davinci_uart_v2p(x) ((x) - PAGE_OFFSET + PLAT_PHYS_OFFSET)
#define davinci_uart_p2v(x) ((x) - PLAT_PHYS_OFFSET + PAGE_OFFSET)
.pushsection .data
davinci_uart_phys: .word 0
davinci_uart_virt: .word 0
.popsection
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
/* Use davinci_uart_phys/virt if already configured */
10: mrc p15, 0, \rp, c1, c0
tst \rp, #1 @ MMU enabled?
ldreq \rp, =davinci_uart_v2p(davinci_uart_phys)
ldrne \rp, =davinci_uart_phys
add \rv, \rp, #4 @ davinci_uart_virt
ldr \rp, [\rp, #0]
ldr \rv, [\rv, #0]
10: adr \rp, 99f @ get effective addr of 99f
ldr \rv, [\rp] @ get absolute addr of 99f
sub \rv, \rv, \rp @ offset between the two
ldr \rp, [\rp, #4] @ abs addr of omap_uart_phys
sub \tmp, \rp, \rv @ make it effective
ldr \rp, [\tmp, #0] @ davinci_uart_phys
ldr \rv, [\tmp, #4] @ davinci_uart_virt
cmp \rp, #0 @ is port configured?
cmpne \rv, #0
bne 99f @ already configured
bne 100f @ already configured
/* Check the debug UART address set in uncompress.h */
mrc p15, 0, \rp, c1, c0
tst \rp, #1 @ MMU enabled?
and \rp, pc, #0xff000000
ldr \rv, =DAVINCI_UART_INFO_OFS
add \rp, \rp, \rv
/* Copy uart phys address from decompressor uart info */
ldreq \rv, =davinci_uart_v2p(davinci_uart_phys)
ldrne \rv, =davinci_uart_phys
ldreq \rp, =DAVINCI_UART_INFO
ldrne \rp, =davinci_uart_p2v(DAVINCI_UART_INFO)
ldr \rp, [\rp, #0]
str \rp, [\rv]
ldr \rv, [\rp, #0]
str \rv, [\tmp, #0]
/* Copy uart virt address from decompressor uart info */
ldreq \rv, =davinci_uart_v2p(davinci_uart_virt)
ldrne \rv, =davinci_uart_virt
ldreq \rp, =DAVINCI_UART_INFO
ldrne \rp, =davinci_uart_p2v(DAVINCI_UART_INFO)
ldr \rp, [\rp, #4]
str \rp, [\rv]
ldr \rv, [\rp, #4]
str \rv, [\tmp, #4]
b 10b
99:
.align
99: .word .
.word davinci_uart_phys
.ltorg
100:
.endm
.macro senduart,rd,rx
......
arch/arm/mach-davinci/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* DaVinci memory space definitions
*
* Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
*
* 2007 (c) MontaVista Software, Inc. This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
/**************************************************************************
* Included Files
**************************************************************************/
#include <asm/page.h>
#include <asm/sizes.h>
/**************************************************************************
* Definitions
**************************************************************************/
#define DAVINCI_DDR_BASE 0x80000000
#define DA8XX_DDR_BASE 0xc0000000
#if defined(CONFIG_ARCH_DAVINCI_DA8XX) && defined(CONFIG_ARCH_DAVINCI_DMx)
#error Cannot enable DaVinci and DA8XX platforms concurrently
#elif defined(CONFIG_ARCH_DAVINCI_DA8XX)
#define PLAT_PHYS_OFFSET DA8XX_DDR_BASE
#else
#define PLAT_PHYS_OFFSET DAVINCI_DDR_BASE
#endif
#define DDR2_SDRCR_OFFSET 0xc
#define DDR2_SRPD_BIT BIT(23)
#define DDR2_MCLKSTOPEN_BIT BIT(30)
#define DDR2_LPMODEN_BIT BIT(31)
#endif /* __ASM_ARCH_MEMORY_H */
arch/arm/mach-davinci/include/mach/serial.h
View file @ 94314a40
......@@ -21,8 +21,9 @@
* macros in debug-macro.S.
*
* This area sits just below the page tables (see arch/arm/kernel/head.S).
* We define it as a relative offset from start of usable RAM.
*/
#define DAVINCI_UART_INFO (PLAT_PHYS_OFFSET + 0x3ff8)
#define DAVINCI_UART_INFO_OFS 0x3ff8
#define DAVINCI_UART0_BASE (IO_PHYS + 0x20000)
#define DAVINCI_UART1_BASE (IO_PHYS + 0x20400)
......
arch/arm/mach-davinci/include/mach/uncompress.h
View file @ 94314a40
......@@ -43,7 +43,12 @@ static inline void flush(void)
static inline void set_uart_info(u32 phys, void * __iomem virt)
{
u32 *uart_info = (u32 *)(DAVINCI_UART_INFO);
/*
* Get address of some.bss variable and round it down
* a la CONFIG_AUTO_ZRELADDR.
*/
u32 ram_start = (u32)&uart & 0xf8000000;
u32 *uart_info = (u32 *)(ram_start + DAVINCI_UART_INFO_OFS);
uart = (u32 *)phys;
uart_info[0] = phys;
......
arch/arm/mach-davinci/sleep.S
View file @ 94314a40
......@@ -22,7 +22,7 @@
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <mach/psc.h>
#include <mach/memory.h>
#include <mach/ddr2.h>
#include "clock.h"
......
arch/arm/mach-dove/include/mach/debug-macro.S
View file @ 94314a40
......@@ -8,7 +8,7 @@
#include <mach/bridge-regs.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =DOVE_SB_REGS_PHYS_BASE
ldr \rv, =DOVE_SB_REGS_VIRT_BASE
orr \rp, \rp, #0x00012000
......
arch/arm/mach-dove/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-dove/include/mach/memory.h
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif
arch/arm/mach-ebsa110/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
*
**/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0xf0000000
orr \rp, \rp, #0x00000be0
mov \rp, \rv
......
arch/arm/mach-ep93xx/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
*/
#include <mach/ep93xx-regs.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =EP93XX_APB_PHYS_BASE @ Physical base
ldr \rv, =EP93XX_APB_VIRT_BASE @ virtual base
orr \rp, \rp, #0x000c0000
......
arch/arm/mach-exynos4/include/mach/debug-macro.S
View file @ 94314a40
......@@ -20,7 +20,7 @@
* aligned and add in the offset when we load the value here.
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, = S3C_PA_UART
ldr \rv, = S3C_VA_UART
#if CONFIG_DEBUG_S3C_UART != 0
......
arch/arm/mach-exynos4/include/mach/entry-macro.S
View file @ 94314a40
......@@ -55,7 +55,7 @@
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #29
cmp \irqnr, #15
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
......@@ -76,8 +76,3 @@
strcc \irqstat, [\base, #GIC_CPU_EOI]
cmpcs \irqnr, \irqnr
.endm
/* As above, this assumes that irqstat and base are preserved.. */
.macro test_for_ltirq, irqnr, irqstat, base, tmp
.endm
arch/arm/mach-exynos4/mct.c
View file @ 94314a40
......@@ -386,9 +386,11 @@ static void exynos4_mct_tick_init(struct clock_event_device *evt)
if (cpu == 0) {
mct_tick0_event_irq.dev_id = &mct_tick[cpu];
evt->irq = IRQ_MCT_L0;
setup_irq(IRQ_MCT_L0, &mct_tick0_event_irq);
} else {
mct_tick1_event_irq.dev_id = &mct_tick[cpu];
evt->irq = IRQ_MCT_L1;
setup_irq(IRQ_MCT_L1, &mct_tick1_event_irq);
irq_set_affinity(IRQ_MCT_L1, cpumask_of(1));
}
......@@ -402,9 +404,10 @@ int __cpuinit local_timer_setup(struct clock_event_device *evt)
return 0;
}
int local_timer_ack(void)
void local_timer_stop(struct clock_event_device *evt)
{
return 0;
evt->set_mode(CLOCK_EVT_MODE_UNUSED, evt);
disable_irq(evt->irq);
}
#endif /* CONFIG_LOCAL_TIMERS */
......
arch/arm/mach-exynos4/platsmp.c
View file @ 94314a40
......@@ -193,12 +193,10 @@ void __init smp_init_cpus(void)
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
/* sanity check */
if (ncores > NR_CPUS) {
printk(KERN_WARNING
"EXYNOS4: no. of cores (%d) greater than configured "
"maximum of %d - clipping\n",
ncores, NR_CPUS);
ncores = NR_CPUS;
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
......
arch/arm/mach-footbridge/include/mach/debug-macro.S
View file @ 94314a40
......@@ -15,7 +15,7 @@
#ifndef CONFIG_DEBUG_DC21285_PORT
/* For NetWinder debugging */
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x000003f8
orr \rv, \rp, #0xff000000 @ virtual
orr \rp, \rp, #0x7c000000 @ physical
......@@ -31,7 +31,7 @@
.equ dc21285_high, ARMCSR_BASE & 0xff000000
.equ dc21285_low, ARMCSR_BASE & 0x00ffffff
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
.if dc21285_low
mov \rp, #dc21285_low
.else
......
arch/arm/mach-gemini/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
*/
#include <mach/hardware.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =GEMINI_UART_BASE @ physical
ldr \rv, =IO_ADDRESS(GEMINI_UART_BASE) @ virtual
.endm
......
arch/arm/mach-gemini/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* Copyright (C) 2001-2006 Storlink, Corp.
* Copyright (C) 2008-2009 Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef __MACH_MEMORY_H
#define __MACH_MEMORY_H
#ifdef CONFIG_GEMINI_MEM_SWAP
# define PLAT_PHYS_OFFSET UL(0x00000000)
#else
# define PLAT_PHYS_OFFSET UL(0x10000000)
#endif
#endif /* __MACH_MEMORY_H */
arch/arm/mach-h720x/include/mach/debug-macro.S
View file @ 94314a40
......@@ -16,7 +16,7 @@
.equ io_virt, IO_VIRT
.equ io_phys, IO_PHYS
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00020000 @ UART1
add \rv, \rp, #io_virt @ virtual address
add \rp, \rp, #io_phys @ physical base address
......
arch/arm/mach-h720x/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-h720x/include/mach/memory.h
*
* Copyright (c) 2000 Jungjun Kim
*
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x40000000)
#endif
arch/arm/mach-integrator/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
*
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x16000000 @ physical base address
mov \rv, #0xf0000000 @ virtual base
add \rv, \rv, #0x16000000 >> 4
......
arch/arm/mach-iop13xx/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
* published by the Free Software Foundation.
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00002300
orr \rp, \rp, #0x00000040
orr \rv, \rp, #0xfe000000 @ virtual
......
arch/arm/mach-iop32x/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
* published by the Free Software Foundation.
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0xfe000000 @ physical as well as virtual
orr \rp, \rp, #0x00800000 @ location of the UART
mov \rv, \rp
......
arch/arm/mach-iop32x/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-iop32x/include/mach/memory.h
*/
#ifndef __MEMORY_H
#define __MEMORY_H
/*
* Physical DRAM offset.
*/
#define PLAT_PHYS_OFFSET UL(0xa0000000)
#endif
arch/arm/mach-iop33x/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
* published by the Free Software Foundation.
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00ff0000
orr \rp, \rp, #0x0000f700
orr \rv, #0xfe000000 @ virtual
......
arch/arm/mach-iop33x/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-iop33x/include/mach/memory.h
*/
#ifndef __MEMORY_H
#define __MEMORY_H
/*
* Physical DRAM offset.
*/
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif
arch/arm/mach-ixp2000/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
*
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00030000
#ifdef __ARMEB__
orr \rp, \rp, #0x00000003
......
arch/arm/mach-ixp23xx/include/mach/debug-macro.S
View file @ 94314a40
......@@ -12,7 +12,7 @@
*/
#include <mach/ixp23xx.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =IXP23XX_PERIPHERAL_PHYS @ physical
ldr \rv, =IXP23XX_PERIPHERAL_VIRT @ virtual
#ifdef __ARMEB__
......
arch/arm/mach-ixp4xx/include/mach/debug-macro.S
View file @ 94314a40
......@@ -10,7 +10,7 @@
* published by the Free Software Foundation.
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
#ifdef __ARMEB__
mov \rp, #3 @ Uart regs are at off set of 3 if
@ byte writes used - Big Endian.
......
arch/arm/mach-ixp4xx/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-ixp4xx/include/mach/memory.h
*
* Copyright (c) 2001-2004 MontaVista Software, Inc.
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#include <asm/sizes.h>
/*
* Physical DRAM offset.
*/
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif
arch/arm/mach-kirkwood/include/mach/debug-macro.S
View file @ 94314a40
......@@ -8,7 +8,7 @@
#include <mach/bridge-regs.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =KIRKWOOD_REGS_PHYS_BASE
ldr \rv, =KIRKWOOD_REGS_VIRT_BASE
orr \rp, \rp, #0x00012000
......
arch/arm/mach-kirkwood/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-kirkwood/include/mach/memory.h
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif
arch/arm/mach-ks8695/include/mach/debug-macro.S
View file @ 94314a40
......@@ -14,7 +14,7 @@
#include <mach/hardware.h>
#include <mach/regs-uart.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =KS8695_UART_PA @ physical base address
ldr \rv, =KS8695_UART_VA @ virtual base address
.endm
......
arch/arm/mach-l7200/include/mach/debug-macro.S
View file @ 94314a40
......@@ -14,7 +14,7 @@
.equ io_virt, IO_BASE
.equ io_phys, IO_START
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00044000 @ UART1
@ mov \rp, #0x00045000 @ UART2
add \rv, \rp, #io_virt @ virtual address
......
arch/arm/mach-lpc32xx/include/mach/debug-macro.S
View file @ 94314a40
......@@ -20,7 +20,7 @@
* Debug output is hardcoded to standard UART 5
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldreq \rp, =0x40090000
ldrne \rv, =0xF4090000
.endm
......
arch/arm/mach-lpc32xx/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-lpc32xx/include/mach/memory.h
*
* Author: Kevin Wells <kevin.wells@nxp.com>
*
* Copyright (C) 2010 NXP Semiconductors
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
/*
* Physical DRAM offset of bank 0
*/
#define PLAT_PHYS_OFFSET UL(0x80000000)
#endif
arch/arm/mach-mmp/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
#include <mach/addr-map.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =APB_PHYS_BASE @ physical
ldr \rv, =APB_VIRT_BASE @ virtual
orr \rp, \rp, #0x00017000
......
arch/arm/mach-mmp/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* linux/arch/arm/mach-mmp/include/mach/memory.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __ASM_MACH_MEMORY_H
#define __ASM_MACH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif /* __ASM_MACH_MEMORY_H */
arch/arm/mach-msm/board-msm7x30.c
View file @ 94314a40
......@@ -24,6 +24,7 @@
#include <linux/smsc911x.h>
#include <linux/usb/msm_hsusb.h>
#include <linux/clkdev.h>
#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
......@@ -42,6 +43,21 @@
extern struct sys_timer msm_timer;
static void __init msm7x30_fixup(struct machine_desc *desc, struct tag *tag,
char **cmdline, struct meminfo *mi)
{
for (; tag->hdr.size; tag = tag_next(tag))
if (tag->hdr.tag == ATAG_MEM && tag->u.mem.start == 0x200000) {
tag->u.mem.start = 0;
tag->u.mem.size += SZ_2M;
}
}
static void __init msm7x30_reserve(void)
{
memblock_remove(0x0, SZ_2M);
}
static int hsusb_phy_init_seq[] = {
0x30, 0x32, /* Enable and set Pre-Emphasis Depth to 20% */
0x02, 0x36, /* Disable CDR Auto Reset feature */
......@@ -107,6 +123,8 @@ static void __init msm7x30_map_io(void)
MACHINE_START(MSM7X30_SURF, "QCT MSM7X30 SURF")
.atag_offset = 0x100,
.fixup = msm7x30_fixup,
.reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
......@@ -115,6 +133,8 @@ MACHINE_END
MACHINE_START(MSM7X30_FFA, "QCT MSM7X30 FFA")
.atag_offset = 0x100,
.fixup = msm7x30_fixup,
.reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
......@@ -123,6 +143,8 @@ MACHINE_END
MACHINE_START(MSM7X30_FLUID, "QCT MSM7X30 FLUID")
.atag_offset = 0x100,
.fixup = msm7x30_fixup,
.reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
......
arch/arm/mach-msm/board-msm8960.c
View file @ 94314a40
......@@ -20,16 +20,34 @@
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/clkdev.h>
#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/hardware/gic.h>
#include <asm/setup.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
#include "devices.h"
static void __init msm8960_fixup(struct machine_desc *desc, struct tag *tag,
char **cmdline, struct meminfo *mi)
{
for (; tag->hdr.size; tag = tag_next(tag))
if (tag->hdr.tag == ATAG_MEM &&
tag->u.mem.start == 0x40200000) {
tag->u.mem.start = 0x40000000;
tag->u.mem.size += SZ_2M;
}
}
static void __init msm8960_reserve(void)
{
memblock_remove(0x40000000, SZ_2M);
}
static void __init msm8960_map_io(void)
{
msm_map_msm8960_io();
......@@ -76,6 +94,8 @@ static void __init msm8960_rumi3_init(void)
}
MACHINE_START(MSM8960_SIM, "QCT MSM8960 SIMULATOR")
.fixup = msm8960_fixup,
.reserve = msm8960_reserve,
.map_io = msm8960_map_io,
.init_irq = msm8960_init_irq,
.timer = &msm_timer,
......@@ -83,6 +103,8 @@ MACHINE_START(MSM8960_SIM, "QCT MSM8960 SIMULATOR")
MACHINE_END
MACHINE_START(MSM8960_RUMI3, "QCT MSM8960 RUMI3")
.fixup = msm8960_fixup,
.reserve = msm8960_reserve,
.map_io = msm8960_map_io,
.init_irq = msm8960_init_irq,
.timer = &msm_timer,
......
arch/arm/mach-msm/board-msm8x60.c
View file @ 94314a40
......@@ -20,14 +20,31 @@
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/hardware/gic.h>
#include <asm/setup.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
static void __init msm8x60_fixup(struct machine_desc *desc, struct tag *tag,
char **cmdline, struct meminfo *mi)
{
for (; tag->hdr.size; tag = tag_next(tag))
if (tag->hdr.tag == ATAG_MEM &&
tag->u.mem.start == 0x40200000) {
tag->u.mem.start = 0x40000000;
tag->u.mem.size += SZ_2M;
}
}
static void __init msm8x60_reserve(void)
{
memblock_remove(0x40000000, SZ_2M);
}
static void __init msm8x60_map_io(void)
{
......@@ -36,8 +53,6 @@ static void __init msm8x60_map_io(void)
static void __init msm8x60_init_irq(void)
{
unsigned int i;
gic_init(0, GIC_PPI_START, MSM_QGIC_DIST_BASE,
(void *)MSM_QGIC_CPU_BASE);
......@@ -49,15 +64,6 @@ static void __init msm8x60_init_irq(void)
*/
if (!machine_is_msm8x60_sim())
writel(0x0000FFFF, MSM_QGIC_DIST_BASE + GIC_DIST_ENABLE_SET);
/* FIXME: Not installing AVS_SVICINT and AVS_SVICINTSWDONE yet
* as they are configured as level, which does not play nice with
* handle_percpu_irq.
*/
for (i = GIC_PPI_START; i < GIC_SPI_START; i++) {
if (i != AVS_SVICINT && i != AVS_SVICINTSWDONE)
irq_set_handler(i, handle_percpu_irq);
}
}
static void __init msm8x60_init(void)
......@@ -65,6 +71,8 @@ static void __init msm8x60_init(void)
}
MACHINE_START(MSM8X60_RUMI3, "QCT MSM8X60 RUMI3")
.fixup = msm8x60_fixup,
.reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
......@@ -72,6 +80,8 @@ MACHINE_START(MSM8X60_RUMI3, "QCT MSM8X60 RUMI3")
MACHINE_END
MACHINE_START(MSM8X60_SURF, "QCT MSM8X60 SURF")
.fixup = msm8x60_fixup,
.reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
......@@ -79,6 +89,8 @@ MACHINE_START(MSM8X60_SURF, "QCT MSM8X60 SURF")
MACHINE_END
MACHINE_START(MSM8X60_SIM, "QCT MSM8X60 SIMULATOR")
.fixup = msm8x60_fixup,
.reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
......@@ -86,6 +98,8 @@ MACHINE_START(MSM8X60_SIM, "QCT MSM8X60 SIMULATOR")
MACHINE_END
MACHINE_START(MSM8X60_FFA, "QCT MSM8X60 FFA")
.fixup = msm8x60_fixup,
.reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
......
arch/arm/mach-msm/include/mach/debug-macro.S
View file @ 94314a40
......@@ -20,7 +20,7 @@
#include <mach/msm_iomap.h>
#if defined(CONFIG_HAS_MSM_DEBUG_UART_PHYS) && !defined(CONFIG_MSM_DEBUG_UART_NONE)
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =MSM_DEBUG_UART_PHYS
ldr \rv, =MSM_DEBUG_UART_BASE
.endm
......@@ -37,7 +37,7 @@
beq 1001b
.endm
#else
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rv, #0xff000000
orr \rv, \rv, #0x00f00000
.endm
......
arch/arm/mach-msm/include/mach/entry-macro-qgic.S
View file @ 94314a40
......@@ -8,81 +8,10 @@
* warranty of any kind, whether express or implied.
*/
#include <mach/hardware.h>
#include <asm/hardware/gic.h>
#include <asm/hardware/entry-macro-gic.S>
.macro disable_fiq
.endm
.macro get_irqnr_preamble, base, tmp
ldr \base, =gic_cpu_base_addr
ldr \base, [\base]
.endm
.macro arch_ret_to_user, tmp1, tmp2
.endm
/*
* The interrupt numbering scheme is defined in the
* interrupt controller spec. To wit:
*
* Migrated the code from ARM MP port to be more consistent
* with interrupt processing , the following still holds true
* however, all interrupts are treated the same regardless of
* if they are local IPI or PPI
*
* Interrupts 0-15 are IPI
* 16-31 are PPI
* (16-18 are the timers)
* 32-1020 are global
* 1021-1022 are reserved
* 1023 is "spurious" (no interrupt)
*
* A simple read from the controller will tell us the number of the
* highest priority enabled interrupt. We then just need to check
* whether it is in the valid range for an IRQ (0-1020 inclusive).
*
* Base ARM code assumes that the local (private) peripheral interrupts
* are not valid, we treat them differently, in that the privates are
* handled like normal shared interrupts with the exception that only
* one processor can register the interrupt and the handler must be
* the same for all processors.
*/
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 =srcCPU,
9-0 =int # */
bic \irqnr, \irqstat, #0x1c00 @mask src
cmp \irqnr, #15
ldr \tmp, =1021
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
.endm
/* We assume that irqstat (the raw value of the IRQ acknowledge
* register) is preserved from the macro above.
* If there is an IPI, we immediately signal end of interrupt on the
* controller, since this requires the original irqstat value which
* we won't easily be able to recreate later.
*/
.macro test_for_ipi, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #16
strcc \irqstat, [\base, #GIC_CPU_EOI]
cmpcs \irqnr, \irqnr
.endm
/* As above, this assumes that irqstat and base are preserved.. */
.macro test_for_ltirq, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
mov \tmp, #0
cmp \irqnr, #16
moveq \tmp, #1
streq \irqstat, [\base, #GIC_CPU_EOI]
cmp \tmp, #0
.endm
arch/arm/mach-msm/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/* arch/arm/mach-msm/include/mach/memory.h
*
* Copyright (C) 2007 Google, Inc.
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
/* physical offset of RAM */
#if defined(CONFIG_ARCH_QSD8X50) && defined(CONFIG_MSM_SOC_REV_A)
#define PLAT_PHYS_OFFSET UL(0x00000000)
#elif defined(CONFIG_ARCH_QSD8X50)
#define PLAT_PHYS_OFFSET UL(0x20000000)
#elif defined(CONFIG_ARCH_MSM7X30)
#define PLAT_PHYS_OFFSET UL(0x00200000)
#elif defined(CONFIG_ARCH_MSM8X60)
#define PLAT_PHYS_OFFSET UL(0x40200000)
#elif defined(CONFIG_ARCH_MSM8960)
#define PLAT_PHYS_OFFSET UL(0x40200000)
#else
#define PLAT_PHYS_OFFSET UL(0x10000000)
#endif
#endif
arch/arm/mach-msm/platsmp.c
View file @ 94314a40
......@@ -156,6 +156,12 @@ void __init smp_init_cpus(void)
{
unsigned int i, ncores = get_core_count();
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
set_cpu_possible(i, true);
......
arch/arm/mach-msm/timer.c
View file @ 94314a40
......@@ -71,12 +71,16 @@ enum timer_location {
struct msm_clock {
struct clock_event_device clockevent;
struct clocksource clocksource;
struct irqaction irq;
unsigned int irq;
void __iomem *regbase;
uint32_t freq;
uint32_t shift;
void __iomem *global_counter;
void __iomem *local_counter;
union {
struct clock_event_device *evt;
struct clock_event_device __percpu **percpu_evt;
};
};
enum {
......@@ -87,13 +91,10 @@ enum {
static struct msm_clock msm_clocks[];
static struct clock_event_device *local_clock_event;
static irqreturn_t msm_timer_interrupt(int irq, void *dev_id)
{
struct clock_event_device *evt = dev_id;
if (smp_processor_id() != 0)
evt = local_clock_event;
struct clock_event_device *evt = *(struct clock_event_device **)dev_id;
if (evt->event_handler == NULL)
return IRQ_HANDLED;
evt->event_handler(evt);
......@@ -171,13 +172,7 @@ static struct msm_clock msm_clocks[] = {
.mask = CLOCKSOURCE_MASK(32),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
},
.irq = {
.name = "gp_timer",
.flags = IRQF_DISABLED | IRQF_TIMER | IRQF_TRIGGER_RISING,
.handler = msm_timer_interrupt,
.dev_id = &msm_clocks[0].clockevent,
.irq = INT_GP_TIMER_EXP
},
.irq = INT_GP_TIMER_EXP,
.freq = GPT_HZ,
},
[MSM_CLOCK_DGT] = {
......@@ -196,13 +191,7 @@ static struct msm_clock msm_clocks[] = {
.mask = CLOCKSOURCE_MASK((32 - MSM_DGT_SHIFT)),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
},
.irq = {
.name = "dg_timer",
.flags = IRQF_DISABLED | IRQF_TIMER | IRQF_TRIGGER_RISING,
.handler = msm_timer_interrupt,
.dev_id = &msm_clocks[1].clockevent,
.irq = INT_DEBUG_TIMER_EXP
},
.irq = INT_DEBUG_TIMER_EXP,
.freq = DGT_HZ >> MSM_DGT_SHIFT,
.shift = MSM_DGT_SHIFT,
}
......@@ -261,10 +250,30 @@ static void __init msm_timer_init(void)
printk(KERN_ERR "msm_timer_init: clocksource_register "
"failed for %s\n", cs->name);
res = setup_irq(clock->irq.irq, &clock->irq);
ce->irq = clock->irq;
if (cpu_is_msm8x60() || cpu_is_msm8960()) {
clock->percpu_evt = alloc_percpu(struct clock_event_device *);
if (!clock->percpu_evt) {
pr_err("msm_timer_init: memory allocation "
"failed for %s\n", ce->name);
continue;
}
*__this_cpu_ptr(clock->percpu_evt) = ce;
res = request_percpu_irq(ce->irq, msm_timer_interrupt,
ce->name, clock->percpu_evt);
if (!res)
enable_percpu_irq(ce->irq, 0);
} else {
clock->evt = ce;
res = request_irq(ce->irq, msm_timer_interrupt,
IRQF_TIMER | IRQF_NOBALANCING | IRQF_TRIGGER_RISING,
ce->name, &clock->evt);
}
if (res)
printk(KERN_ERR "msm_timer_init: setup_irq "
"failed for %s\n", cs->name);
pr_err("msm_timer_init: request_irq failed for %s\n",
ce->name);
clockevents_register_device(ce);
}
......@@ -273,6 +282,7 @@ static void __init msm_timer_init(void)
#ifdef CONFIG_SMP
int __cpuinit local_timer_setup(struct clock_event_device *evt)
{
static bool local_timer_inited;
struct msm_clock *clock = &msm_clocks[MSM_GLOBAL_TIMER];
/* Use existing clock_event for cpu 0 */
......@@ -281,12 +291,13 @@ int __cpuinit local_timer_setup(struct clock_event_device *evt)
writel(DGT_CLK_CTL_DIV_4, MSM_TMR_BASE + DGT_CLK_CTL);
if (!local_clock_event) {
if (!local_timer_inited) {
writel(0, clock->regbase + TIMER_ENABLE);
writel(0, clock->regbase + TIMER_CLEAR);
writel(~0, clock->regbase + TIMER_MATCH_VAL);
local_timer_inited = true;
}
evt->irq = clock->irq.irq;
evt->irq = clock->irq;
evt->name = "local_timer";
evt->features = CLOCK_EVT_FEAT_ONESHOT;
evt->rating = clock->clockevent.rating;
......@@ -298,17 +309,17 @@ int __cpuinit local_timer_setup(struct clock_event_device *evt)
clockevent_delta2ns(0xf0000000 >> clock->shift, evt);
evt->min_delta_ns = clockevent_delta2ns(4, evt);
local_clock_event = evt;
gic_enable_ppi(clock->irq.irq);
*__this_cpu_ptr(clock->percpu_evt) = evt;
enable_percpu_irq(evt->irq, 0);
clockevents_register_device(evt);
return 0;
}
inline int local_timer_ack(void)
void local_timer_stop(struct clock_event_device *evt)
{
return 1;
evt->set_mode(CLOCK_EVT_MODE_UNUSED, evt);
disable_percpu_irq(evt->irq);
}
#endif
......
arch/arm/mach-mv78xx0/include/mach/debug-macro.S
View file @ 94314a40
......@@ -8,7 +8,7 @@
#include <mach/mv78xx0.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =MV78XX0_REGS_PHYS_BASE
ldr \rv, =MV78XX0_REGS_VIRT_BASE
orr \rp, \rp, #0x00012000
......
arch/arm/mach-mv78xx0/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-mv78xx0/include/mach/memory.h
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif
arch/arm/mach-mxs/include/mach/debug-macro.S
View file @ 94314a40
......@@ -30,7 +30,7 @@
#define UART_VADDR MXS_IO_ADDRESS(UART_PADDR)
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =UART_PADDR @ physical
ldr \rv, =UART_VADDR @ virtual
.endm
......
arch/arm/mach-mxs/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
*/
#ifndef __MACH_MXS_MEMORY_H__
#define __MACH_MXS_MEMORY_H__
#define PHYS_OFFSET UL(0x40000000)
#endif /* __MACH_MXS_MEMORY_H__ */
arch/arm/mach-netx/include/mach/debug-macro.S
View file @ 94314a40
......@@ -13,7 +13,7 @@
#include "hardware.h"
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00000a00
orr \rv, \rp, #io_p2v(0x00100000) @ virtual
orr \rp, \rp, #0x00100000 @ physical
......
arch/arm/mach-netx/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-netx/include/mach/memory.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2
* as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x80000000)
#endif
arch/arm/mach-nomadik/include/mach/debug-macro.S
View file @ 94314a40
......@@ -10,7 +10,7 @@
*
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00100000
add \rp, \rp, #0x000fb000
add \rv, \rp, #0xf0000000 @ virtual base
......
arch/arm/mach-nomadik/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* mach-nomadik/include/mach/memory.h
*
* Copyright (C) 1999 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
/*
* Physical DRAM offset.
*/
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif
arch/arm/mach-nuc93x/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-nuc93x/include/mach/memory.h
*
* Copyright (c) 2008 Nuvoton technology corporation
* All rights reserved.
*
* Wan ZongShun <mcuos.com@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif
arch/arm/mach-omap1/include/mach/debug-macro.S
View file @ 94314a40
......@@ -13,13 +13,8 @@
#include <linux/serial_reg.h>
#include <asm/memory.h>
#include <plat/serial.h>
#define omap_uart_v2p(x) ((x) - PAGE_OFFSET + PLAT_PHYS_OFFSET)
#define omap_uart_p2v(x) ((x) - PLAT_PHYS_OFFSET + PAGE_OFFSET)
.pushsection .data
omap_uart_phys: .word 0x0
omap_uart_virt: .word 0x0
......@@ -31,26 +26,24 @@ omap_uart_virt: .word 0x0
* the desired UART phys and virt addresses temporarily into
* the omap_uart_phys and omap_uart_virt above.
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
/* Use omap_uart_phys/virt if already configured */
9: mrc p15, 0, \rp, c1, c0
tst \rp, #1 @ MMU enabled?
ldreq \rp, =omap_uart_v2p(omap_uart_phys) @ MMU disabled
ldrne \rp, =omap_uart_phys @ MMU enabled
add \rv, \rp, #4 @ omap_uart_virt
ldr \rp, [\rp, #0]
ldr \rv, [\rv, #0]
9: adr \rp, 99f @ get effective addr of 99f
ldr \rv, [\rp] @ get absolute addr of 99f
sub \rv, \rv, \rp @ offset between the two
ldr \rp, [\rp, #4] @ abs addr of omap_uart_phys
sub \tmp, \rp, \rv @ make it effective
ldr \rp, [\tmp, #0] @ omap_uart_phys
ldr \rv, [\tmp, #4] @ omap_uart_virt
cmp \rp, #0 @ is port configured?
cmpne \rv, #0
bne 99f @ already configured
bne 100f @ already configured
/* Check the debug UART configuration set in uncompress.h */
mrc p15, 0, \rp, c1, c0
tst \rp, #1 @ MMU enabled?
ldreq \rp, =OMAP_UART_INFO @ MMU not enabled
ldrne \rp, =omap_uart_p2v(OMAP_UART_INFO) @ MMU enabled
ldr \rp, [\rp, #0]
and \rp, pc, #0xff000000
ldr \rv, =OMAP_UART_INFO_OFS
ldr \rp, [\rp, \rv]
/* Select the UART to use based on the UART1 scratchpad value */
10: cmp \rp, #0 @ no port configured?
......@@ -74,17 +67,18 @@ omap_uart_virt: .word 0x0
/* Store both phys and virt address for the uart */
98: add \rp, \rp, #0xff000000 @ phys base
mrc p15, 0, \rv, c1, c0
tst \rv, #1 @ MMU enabled?
ldreq \rv, =omap_uart_v2p(omap_uart_phys) @ MMU disabled
ldrne \rv, =omap_uart_phys @ MMU enabled
str \rp, [\rv, #0]
str \rp, [\tmp, #0] @ omap_uart_phys
sub \rp, \rp, #0xff000000 @ phys base
add \rp, \rp, #0xfe000000 @ virt base
add \rv, \rv, #4 @ omap_uart_lsr
str \rp, [\rv, #0]
str \rp, [\tmp, #4] @ omap_uart_virt
b 9b
99:
.align
99: .word .
.word omap_uart_phys
.ltorg
100:
.endm
.macro senduart,rd,rx
......
arch/arm/mach-omap1/include/mach/memory.h
View file @ 94314a40
......@@ -2,4 +2,55 @@
* arch/arm/mach-omap1/include/mach/memory.h
*/
#include <plat/memory.h>
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
/*
* Physical DRAM offset.
*/
#define PLAT_PHYS_OFFSET UL(0x10000000)
/*
* Bus address is physical address, except for OMAP-1510 Local Bus.
* OMAP-1510 bus address is translated into a Local Bus address if the
* OMAP bus type is lbus. We do the address translation based on the
* device overriding the defaults used in the dma-mapping API.
* Note that the is_lbus_device() test is not very efficient on 1510
* because of the strncmp().
*/
#ifdef CONFIG_ARCH_OMAP15XX
/*
* OMAP-1510 Local Bus address offset
*/
#define OMAP1510_LB_OFFSET UL(0x30000000)
#define virt_to_lbus(x) ((x) - PAGE_OFFSET + OMAP1510_LB_OFFSET)
#define lbus_to_virt(x) ((x) - OMAP1510_LB_OFFSET + PAGE_OFFSET)
#define is_lbus_device(dev) (cpu_is_omap15xx() && dev && (strncmp(dev_name(dev), "ohci", 4) == 0))
#define __arch_pfn_to_dma(dev, pfn) \
({ dma_addr_t __dma = __pfn_to_phys(pfn); \
if (is_lbus_device(dev)) \
__dma = __dma - PHYS_OFFSET + OMAP1510_LB_OFFSET; \
__dma; })
#define __arch_dma_to_pfn(dev, addr) \
({ dma_addr_t __dma = addr; \
if (is_lbus_device(dev)) \
__dma += PHYS_OFFSET - OMAP1510_LB_OFFSET; \
__phys_to_pfn(__dma); \
})
#define __arch_dma_to_virt(dev, addr) ({ (void *) (is_lbus_device(dev) ? \
lbus_to_virt(addr) : \
__phys_to_virt(addr)); })
#define __arch_virt_to_dma(dev, addr) ({ unsigned long __addr = (unsigned long)(addr); \
(dma_addr_t) (is_lbus_device(dev) ? \
virt_to_lbus(__addr) : \
__virt_to_phys(__addr)); })
#endif /* CONFIG_ARCH_OMAP15XX */
#endif
arch/arm/mach-omap2/include/mach/debug-macro.S
View file @ 94314a40
......@@ -13,15 +13,10 @@
#include <linux/serial_reg.h>
#include <asm/memory.h>
#include <plat/serial.h>
#define UART_OFFSET(addr) ((addr) & 0x00ffffff)
#define omap_uart_v2p(x) ((x) - PAGE_OFFSET + PLAT_PHYS_OFFSET)
#define omap_uart_p2v(x) ((x) - PLAT_PHYS_OFFSET + PAGE_OFFSET)
.pushsection .data
omap_uart_phys: .word 0
omap_uart_virt: .word 0
......@@ -34,26 +29,25 @@ omap_uart_lsr: .word 0
* the desired UART phys and virt addresses temporarily into
* the omap_uart_phys and omap_uart_virt above.
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
/* Use omap_uart_phys/virt if already configured */
10: mrc p15, 0, \rp, c1, c0
tst \rp, #1 @ MMU enabled?
ldreq \rp, =omap_uart_v2p(omap_uart_phys) @ MMU disabled
ldrne \rp, =omap_uart_phys @ MMU enabled
add \rv, \rp, #4 @ omap_uart_virt
ldr \rp, [\rp, #0]
ldr \rv, [\rv, #0]
10: adr \rp, 99f @ get effective addr of 99f
ldr \rv, [\rp] @ get absolute addr of 99f
sub \rv, \rv, \rp @ offset between the two
ldr \rp, [\rp, #4] @ abs addr of omap_uart_phys
sub \tmp, \rp, \rv @ make it effective
ldr \rp, [\tmp, #0] @ omap_uart_phys
ldr \rv, [\tmp, #4] @ omap_uart_virt
cmp \rp, #0 @ is port configured?
cmpne \rv, #0
bne 99f @ already configured
bne 100f @ already configured
/* Check the debug UART configuration set in uncompress.h */
mrc p15, 0, \rp, c1, c0
tst \rp, #1 @ MMU enabled?
ldreq \rp, =OMAP_UART_INFO @ MMU not enabled
ldrne \rp, =omap_uart_p2v(OMAP_UART_INFO) @ MMU enabled
ldr \rp, [\rp, #0]
mov \rp, pc
ldr \rv, =OMAP_UART_INFO_OFS
and \rp, \rp, #0xff000000
ldr \rp, [\rp, \rv]
/* Select the UART to use based on the UART1 scratchpad value */
cmp \rp, #0 @ no port configured?
......@@ -106,50 +100,47 @@ omap_uart_lsr: .word 0
b 98f
83: mov \rp, #UART_OFFSET(TI816X_UART3_BASE)
b 98f
95: ldr \rp, =ZOOM_UART_BASE
mrc p15, 0, \rv, c1, c0
tst \rv, #1 @ MMU enabled?
ldreq \rv, =omap_uart_v2p(omap_uart_phys) @ MMU disabled
ldrne \rv, =omap_uart_phys @ MMU enabled
str \rp, [\rv, #0]
str \rp, [\tmp, #0] @ omap_uart_phys
ldr \rp, =ZOOM_UART_VIRT
add \rv, \rv, #4 @ omap_uart_virt
str \rp, [\rv, #0]
str \rp, [\tmp, #4] @ omap_uart_virt
mov \rp, #(UART_LSR << ZOOM_PORT_SHIFT)
add \rv, \rv, #4 @ omap_uart_lsr
str \rp, [\rv, #0]
str \rp, [\tmp, #8] @ omap_uart_lsr
b 10b
/* Store both phys and virt address for the uart */
98: add \rp, \rp, #0x48000000 @ phys base
mrc p15, 0, \rv, c1, c0
tst \rv, #1 @ MMU enabled?
ldreq \rv, =omap_uart_v2p(omap_uart_phys) @ MMU disabled
ldrne \rv, =omap_uart_phys @ MMU enabled
str \rp, [\rv, #0]
str \rp, [\tmp, #0] @ omap_uart_phys
sub \rp, \rp, #0x48000000 @ phys base
add \rp, \rp, #0xfa000000 @ virt base
add \rv, \rv, #4 @ omap_uart_virt
str \rp, [\rv, #0]
str \rp, [\tmp, #4] @ omap_uart_virt
mov \rp, #(UART_LSR << OMAP_PORT_SHIFT)
add \rv, \rv, #4 @ omap_uart_lsr
str \rp, [\rv, #0]
str \rp, [\tmp, #8] @ omap_uart_lsr
b 10b
99:
.align
99: .word .
.word omap_uart_phys
.ltorg
100: /* Pass the UART_LSR reg address */
ldr \tmp, [\tmp, #8] @ omap_uart_lsr
add \rp, \rp, \tmp
add \rv, \rv, \tmp
.endm
.macro senduart,rd,rx
strb \rd, [\rx]
orr \rd, \rd, \rx, lsl #24 @ preserve LSR reg offset
bic \rx, \rx, #0xff @ get base (THR) reg address
strb \rd, [\rx] @ send lower byte of rd
orr \rx, \rx, \rd, lsr #24 @ restore original rx (LSR)
bic \rd, \rd, #(0xff << 24) @ restore original rd
.endm
.macro busyuart,rd,rx
1001: mrc p15, 0, \rd, c1, c0
tst \rd, #1 @ MMU enabled?
ldreq \rd, =omap_uart_v2p(omap_uart_lsr) @ MMU disabled
ldrne \rd, =omap_uart_lsr @ MMU enabled
ldr \rd, [\rd, #0]
ldrb \rd, [\rx, \rd]
1001: ldrb \rd, [\rx] @ rx contains UART_LSR address
and \rd, \rd, #(UART_LSR_TEMT | UART_LSR_THRE)
teq \rd, #(UART_LSR_TEMT | UART_LSR_THRE)
bne 1001b
......
arch/arm/mach-omap2/include/mach/entry-macro.S
View file @ 94314a40
......@@ -78,7 +78,7 @@
4401: ldr \irqstat, [\base, #GIC_CPU_INTACK]
ldr \tmp, =1021
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #29
cmp \irqnr, #15
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
......@@ -101,18 +101,6 @@
it cs
cmpcs \irqnr, \irqnr
.endm
/* As above, this assumes that irqstat and base are preserved */
.macro test_for_ltirq, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
mov \tmp, #0
cmp \irqnr, #29
itt eq
moveq \tmp, #1
streq \irqstat, [\base, #GIC_CPU_EOI]
cmp \tmp, #0
.endm
#endif /* CONFIG_SMP */
#else /* MULTI_OMAP2 */
......
arch/arm/mach-omap2/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-omap2/include/mach/memory.h
*/
#include <plat/memory.h>
arch/arm/mach-omap2/omap-smp.c
View file @ 94314a40
......@@ -109,12 +109,10 @@ void __init smp_init_cpus(void)
ncores = scu_get_core_count(scu_base);
/* sanity check */
if (ncores > NR_CPUS) {
printk(KERN_WARNING
"OMAP4: no. of cores (%d) greater than configured "
"maximum of %d - clipping\n",
ncores, NR_CPUS);
ncores = NR_CPUS;
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
......
arch/arm/mach-orion5x/include/mach/debug-macro.S
View file @ 94314a40
......@@ -10,7 +10,7 @@
#include <mach/orion5x.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =ORION5X_REGS_PHYS_BASE
ldr \rv, =ORION5X_REGS_VIRT_BASE
orr \rp, \rp, #0x00012000
......
arch/arm/mach-orion5x/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-orion5x/include/mach/memory.h
*
* Marvell Orion memory definitions
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x00000000)
#endif
arch/arm/mach-pnx4008/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
*
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00090000
add \rv, \rp, #0xf4000000 @ virtual
add \rp, \rp, #0x40000000 @ physical
......
arch/arm/mach-pnx4008/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-pnx4008/include/mach/memory.h
*
* Copyright (c) 2005 Philips Semiconductors
* Copyright (c) 2005 MontaVista Software, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
/*
* Physical DRAM offset.
*/
#define PLAT_PHYS_OFFSET UL(0x80000000)
#endif
arch/arm/mach-prima2/include/mach/debug-macro.S
View file @ 94314a40
......@@ -9,7 +9,7 @@
#include <mach/hardware.h>
#include <mach/uart.h>
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
ldr \rp, =SIRFSOC_UART1_PA_BASE @ physical
ldr \rv, =SIRFSOC_UART1_VA_BASE @ virtual
.endm
......
arch/arm/mach-prima2/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-prima2/include/mach/memory.h
*
* Copyright (c) 2010 – 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
*
* Licensed under GPLv2 or later.
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x00000000)
/*
* Restrict DMA-able region to workaround silicon limitation.
* The limitation restricts buffers available for DMA to SD/MMC
* hardware to be below 256MB
*/
#define ARM_DMA_ZONE_SIZE (SZ_256M)
#endif
arch/arm/mach-prima2/l2x0.c
View file @ 94314a40
......@@ -13,7 +13,6 @@
#include <linux/of.h>
#include <linux/of_address.h>
#include <asm/hardware/cache-l2x0.h>
#include <mach/memory.h>
#define L2X0_ADDR_FILTERING_START 0xC00
#define L2X0_ADDR_FILTERING_END 0xC04
......@@ -41,9 +40,9 @@ static int __init sirfsoc_of_l2x_init(void)
/*
* set the physical memory windows L2 cache will cover
*/
writel_relaxed(PLAT_PHYS_OFFSET + 1024 * 1024 * 1024,
writel_relaxed(PHYS_OFFSET + 1024 * 1024 * 1024,
sirfsoc_l2x_base + L2X0_ADDR_FILTERING_END);
writel_relaxed(PLAT_PHYS_OFFSET | 0x1,
writel_relaxed(PHYS_OFFSET | 0x1,
sirfsoc_l2x_base + L2X0_ADDR_FILTERING_START);
writel_relaxed(0,
......
arch/arm/mach-prima2/prima2.c
View file @ 94314a40
......@@ -36,6 +36,7 @@ MACHINE_START(PRIMA2_EVB, "prima2cb")
.map_io = sirfsoc_map_lluart,
.init_irq = sirfsoc_of_irq_init,
.timer = &sirfsoc_timer,
.dma_zone_size = SZ_256M,
.init_machine = sirfsoc_mach_init,
.dt_compat = prima2cb_dt_match,
MACHINE_END
arch/arm/mach-pxa/include/mach/debug-macro.S
View file @ 94314a40
......@@ -13,7 +13,7 @@
#include "hardware.h"
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00100000
orr \rv, \rp, #io_p2v(0x40000000) @ virtual
orr \rp, \rp, #0x40000000 @ physical
......
arch/arm/mach-pxa/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
/*
* arch/arm/mach-pxa/include/mach/memory.h
*
* Author: Nicolas Pitre
* Copyright: (C) 2001 MontaVista Software Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
/*
* Physical DRAM offset.
*/
#define PLAT_PHYS_OFFSET UL(0xa0000000)
#endif
arch/arm/mach-pxa/z2.c
View file @ 94314a40
......@@ -686,7 +686,7 @@ static void z2_power_off(void)
*/
PSPR = 0x0;
local_irq_disable();
pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP, PLAT_PHYS_OFFSET - PAGE_OFFSET);
pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP, PHYS_OFFSET - PAGE_OFFSET);
}
#else
#define z2_power_off NULL
......
arch/arm/mach-realview/include/mach/debug-macro.S
View file @ 94314a40
......@@ -33,7 +33,7 @@
#error "Unknown RealView platform"
#endif
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #DEBUG_LL_UART_OFFSET
orr \rv, \rp, #0xfb000000 @ virtual base
orr \rp, \rp, #0x10000000 @ physical base
......
arch/arm/mach-realview/platsmp.c
View file @ 94314a40
......@@ -52,12 +52,10 @@ void __init smp_init_cpus(void)
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
/* sanity check */
if (ncores > NR_CPUS) {
printk(KERN_WARNING
"Realview: no. of cores (%d) greater than configured "
"maximum of %d - clipping\n",
ncores, NR_CPUS);
ncores = NR_CPUS;
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
......
arch/arm/mach-rpc/include/mach/debug-macro.S
View file @ 94314a40
......@@ -11,7 +11,7 @@
*
*/
.macro addruart, rp, rv
.macro addruart, rp, rv, tmp
mov \rp, #0x00010000
orr \rp, \rp, #0x00000fe0
orr \rv, \rp, #0xe0000000 @ virtual
......
arch/arm/mach-s3c2400/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-s3c2410/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-s3c64xx/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-s5p64x0/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-s5pc100/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-shmobile/entry-intc.S
View file @ 94314a40
This diff is collapsed.
arch/arm/mach-shmobile/platsmp.c
View file @ 94314a40
This diff is collapsed.
arch/arm/mach-spear3xx/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-spear6xx/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-tegra/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-tegra/platsmp.c
View file @ 94314a40
This diff is collapsed.
arch/arm/mach-ux500/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-ux500/platsmp.c
View file @ 94314a40
This diff is collapsed.
arch/arm/mach-versatile/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-vexpress/ct-ca9x4.c
View file @ 94314a40
This diff is collapsed.
arch/arm/mach-vexpress/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-vt8500/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-w90x900/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/mach-zynq/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/plat-mxc/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/plat-omap/Kconfig
View file @ 94314a40
This diff is collapsed.
arch/arm/plat-omap/include/plat/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/plat-omap/include/plat/serial.h
View file @ 94314a40
This diff is collapsed.
arch/arm/plat-spear/include/plat/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
arch/arm/plat-tcc/include/mach/memory.h deleted 100644 → 0
View file @ 929f58ae
This diff is collapsed.
drivers/of/irq.c
View file @ 94314a40
This diff is collapsed.
drivers/usb/musb/musb_debugfs.c
View file @ 94314a40
This diff is collapsed.
include/linux/interrupt.h
View file @ 94314a40
This diff is collapsed.
include/linux/irq.h
View file @ 94314a40
This diff is collapsed.
include/linux/irqdesc.h
View file @ 94314a40
This diff is collapsed.
include/linux/irqdomain.h
View file @ 94314a40
This diff is collapsed.
include/linux/of_irq.h
View file @ 94314a40
This diff is collapsed.
kernel/irq/chip.c
View file @ 94314a40
This diff is collapsed.
kernel/irq/internals.h
View file @ 94314a40
This diff is collapsed.
kernel/irq/irqdesc.c
View file @ 94314a40
This diff is collapsed.
kernel/irq/irqdomain.c
View file @ 94314a40
This diff is collapsed.
kernel/irq/manage.c
View file @ 94314a40
This diff is collapsed.
kernel/irq/settings.h
View file @ 94314a40
This diff is collapsed.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7