Commit 97af8e1c authored by Paul Burton's avatar Paul Burton Committed by Ralf Baechle

MIPS: Malta: Probe pflash via DT

Add the DT nodes required to probe the CFI compatible parallel monitor
flash found on the Malta development board, and remove the platform
code that was previously doing it. Delete the now-empty malta-platform.c
file. Adjust the Malta defconfigs that enable MTD & the pflash/CFI
driver to enable CONFIG_MTD_PHYSMAP_OF rather than CONFIG_MTD_PHYSMAP in
order to preserve their behaviour.
Signed-off-by: default avatarPaul Burton <paul.burton@imgtec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14278/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent 0a46ffa3
......@@ -50,6 +50,37 @@ i8259: interrupt-controller@20 {
interrupts = <GIC_SHARED 3 IRQ_TYPE_LEVEL_HIGH>;
};
flash@1e000000 {
compatible = "intel,dt28f160", "cfi-flash";
reg = <0x1e000000 0x400000>;
bank-width = <4>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
yamon@0 {
label = "YAMON";
reg = <0x0 0x100000>;
read-only;
};
user-fs@100000 {
label = "User FS";
reg = <0x100000 0x2e0000>;
};
board-config@3e0000 {
label = "Board Config";
reg = <0x3e0000 0x20000>;
read-only;
};
};
};
isa {
compatible = "isa";
#address-cells = <2>;
......
......@@ -230,7 +230,7 @@ CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_CFI_STAA=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_PHYSMAP_OF=y
CONFIG_MTD_UBI=m
CONFIG_MTD_UBI_GLUEBI=m
CONFIG_BLK_DEV_FD=m
......
......@@ -235,7 +235,7 @@ CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_CFI_STAA=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_PHYSMAP_OF=y
CONFIG_MTD_UBI=m
CONFIG_MTD_UBI_GLUEBI=m
CONFIG_BLK_DEV_FD=m
......
......@@ -234,7 +234,7 @@ CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_CFI_STAA=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_PHYSMAP_OF=y
CONFIG_MTD_UBI=m
CONFIG_MTD_UBI_GLUEBI=m
CONFIG_BLK_DEV_FD=m
......
......@@ -231,7 +231,7 @@ CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_CFI_STAA=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_PHYSMAP_OF=y
CONFIG_MTD_UBI=m
CONFIG_MTD_UBI_GLUEBI=m
CONFIG_BLK_DEV_FD=m
......
......@@ -25,11 +25,8 @@
#include <linux/serial_8250.h>
#include <linux/module.h>
#include <linux/irq.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/mips-boards/maltaint.h>
#include <mtd/mtd-abi.h>
#define SMC_PORT(base, int) \
{ \
......@@ -67,49 +64,8 @@ static struct platform_device malta_uart8250_device = {
},
};
static struct mtd_partition malta_mtd_partitions[] = {
{
.name = "YAMON",
.offset = 0x0,
.size = 0x100000,
.mask_flags = MTD_WRITEABLE
}, {
.name = "User FS",
.offset = 0x100000,
.size = 0x2e0000
}, {
.name = "Board Config",
.offset = 0x3e0000,
.size = 0x020000,
.mask_flags = MTD_WRITEABLE
}
};
static struct physmap_flash_data malta_flash_data = {
.width = 4,
.nr_parts = ARRAY_SIZE(malta_mtd_partitions),
.parts = malta_mtd_partitions
};
static struct resource malta_flash_resource = {
.start = 0x1e000000,
.end = 0x1e3fffff,
.flags = IORESOURCE_MEM
};
static struct platform_device malta_flash_device = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &malta_flash_data,
},
.num_resources = 1,
.resource = &malta_flash_resource,
};
static struct platform_device *malta_devices[] __initdata = {
&malta_uart8250_device,
&malta_flash_device,
};
static int __init malta_add_devices(void)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment