Commit 99e09eac authored by Mauro Carvalho Chehab's avatar Mauro Carvalho Chehab

V4L/DVB (7448): Add support for Kworld ATSC 120

This board has a s5h1409 demod, plus a xc30x8 tuner (probably, xc3018).

This patch adds proper support for radio, video, s-video, composite and ATSC.
However, support for radio and video depends on having s5h1409 i2c gate open,
otherwise, xc30x8 chip won't be visible.

For a better support, some rework is needed on cx88 driver, to allow adding
xc30x8 to i2c bus without sending i2c 0 byte reading to 0xc2 address.

Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com> for helping to figure
out the proper parameters for s5h1409 and the GPIO pins used by each
configuration.
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@infradead.org>
parent a2401d9e
......@@ -65,3 +65,4 @@
64 -> DViCO FusionHDTV DVB-T PRO [18ac:db30]
65 -> DViCO FusionHDTV 7 Gold [18ac:d610]
66 -> Prolink Pixelview MPEG 8000GT [1554:4935]
67 -> Kworld PlusTV HD PCI 120 (ATSC 120) [17de:08c1]
......@@ -27,7 +27,6 @@
#include "cx88.h"
#include "tea5767.h"
#include "tuner-xc2028.h"
static unsigned int tuner[] = {[0 ... (CX88_MAXBOARDS - 1)] = UNSET };
static unsigned int radio[] = {[0 ... (CX88_MAXBOARDS - 1)] = UNSET };
......@@ -1614,6 +1613,45 @@ static const struct cx88_board cx88_boards[] = {
.gpio2 = 0x0cfb,
},
},
/* Both radio, analog and ATSC work with this board.
However, for analog to work, s5h1409 gate should be open,
otherwise, tuner-xc3028 won't be detected.
A proper fix require using the newer i2c methods to add
tuner-xc3028 without doing an i2c probe.
*/
[CX88_BOARD_KWORLD_ATSC_120] = {
.name = "Kworld PlusTV HD PCI 120 (ATSC 120)",
.tuner_type = TUNER_XC2028,
.radio_type = UNSET,
.tuner_addr = ADDR_UNSET,
.radio_addr = ADDR_UNSET,
.input = { {
.type = CX88_VMUX_TELEVISION,
.vmux = 0,
.gpio0 = 0x000000ff,
.gpio1 = 0x0000f35d,
.gpio2 = 0x00000000,
}, {
.type = CX88_VMUX_COMPOSITE1,
.vmux = 1,
.gpio0 = 0x000000ff,
.gpio1 = 0x0000f37e,
.gpio2 = 0x00000000,
}, {
.type = CX88_VMUX_SVIDEO,
.vmux = 2,
.gpio0 = 0x000000ff,
.gpio1 = 0x0000f37e,
.gpio2 = 0x00000000,
} },
.radio = {
.type = CX88_RADIO,
.gpio0 = 0x000000ff,
.gpio1 = 0x0000f35d,
.gpio2 = 0x00000000,
},
.mpeg = CX88_MPEG_DVB,
},
};
/* ------------------------------------------------------------------ */
......@@ -1959,6 +1997,10 @@ static const struct cx88_subid cx88_subids[] = {
.subvendor = 0x1554,
.subdevice = 0x4935,
.card = CX88_BOARD_PROLINK_PV_8000GT,
}, {
.subvendor = 0x17de,
.subdevice = 0x08c1,
.card = CX88_BOARD_KWORLD_ATSC_120,
},
};
......@@ -2200,6 +2242,7 @@ static int cx88_xc2028_tuner_callback(struct cx88_core *core,
case CX88_BOARD_WINFAST_TV2000_XP_GLOBAL:
case CX88_BOARD_POWERCOLOR_REAL_ANGEL:
case CX88_BOARD_GENIATECH_X8000_MT:
case CX88_BOARD_KWORLD_ATSC_120:
return cx88_xc3028_geniatech_tuner_callback(core,
command, arg);
case CX88_BOARD_PROLINK_PV_8000GT:
......@@ -2363,6 +2406,40 @@ static void cx88_card_setup_pre_i2c(struct cx88_core *core)
}
}
/*
* Sets board-dependent xc3028 configuration
*/
void cx88_setup_xc3028(struct cx88_core *core, struct xc2028_ctrl *ctl)
{
memset(ctl, 0, sizeof(*ctl));
ctl->fname = XC2028_DEFAULT_FIRMWARE;
ctl->max_len = 64;
switch (core->boardnr) {
case CX88_BOARD_POWERCOLOR_REAL_ANGEL:
/* Doesn't work with firmware version 2.7 */
ctl->fname = "xc3028-v25.fw";
break;
case CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO:
ctl->scode_table = XC3028_FE_ZARLINK456;
break;
case CX88_BOARD_KWORLD_ATSC_120:
case CX88_BOARD_DVICO_FUSIONHDTV_5_PCI_NANO:
ctl->demod = XC3028_FE_OREN538;
break;
case CX88_BOARD_PROLINK_PV_8000GT:
/*
* This board uses non-MTS firmware
*/
break;
default:
ctl->demod = XC3028_FE_OREN538;
ctl->mts = 1;
}
}
EXPORT_SYMBOL_GPL(cx88_setup_xc3028);
static void cx88_card_setup(struct cx88_core *core)
{
static u8 eeprom[256];
......@@ -2481,36 +2558,13 @@ static void cx88_card_setup(struct cx88_core *core)
struct v4l2_priv_tun_config xc2028_cfg;
struct xc2028_ctrl ctl;
memset(&xc2028_cfg, 0, sizeof(xc2028_cfg));
memset(&ctl, 0, sizeof(ctl));
ctl.fname = XC2028_DEFAULT_FIRMWARE;
ctl.max_len = 64;
switch (core->boardnr) {
case CX88_BOARD_POWERCOLOR_REAL_ANGEL:
/* Doesn't work with firmware version 2.7 */
ctl.fname = "xc3028-v25.fw";
break;
case CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO:
ctl.scode_table = XC3028_FE_ZARLINK456;
break;
case CX88_BOARD_DVICO_FUSIONHDTV_5_PCI_NANO:
ctl.demod = XC3028_FE_OREN538;
break;
case CX88_BOARD_PROLINK_PV_8000GT:
/*
* This board uses non-MTS firmware
*/
break;
default:
ctl.demod = XC3028_FE_OREN538;
ctl.mts = 1;
}
/* Fills device-dependent initialization parameters */
cx88_setup_xc3028(core, &ctl);
/* Sends parameters to xc2028/3028 tuner */
memset(&xc2028_cfg, 0, sizeof(xc2028_cfg));
xc2028_cfg.tuner = TUNER_XC2028;
xc2028_cfg.priv = &ctl;
info_printk(core, "Asking xc2028/3028 to load firmware %s\n",
ctl.fname);
cx88_call_i2c_clients(core, TUNER_SET_CONFIG, &xc2028_cfg);
......
......@@ -45,7 +45,6 @@
#include "nxt200x.h"
#include "cx24123.h"
#include "isl6421.h"
#include "tuner-xc2028.h"
#include "tuner-xc2028-types.h"
#include "tuner-simple.h"
#include "tda9887.h"
......@@ -443,6 +442,16 @@ static struct s5h1409_config dvico_hdtv5_pci_nano_config = {
.mpeg_timing = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK,
};
static struct s5h1409_config kworld_atsc_120_config = {
.demod_address = 0x32 >> 1,
.qam_if = 44000,
.output_mode = S5H1409_SERIAL_OUTPUT,
.gpio = S5H1409_GPIO_OFF,
.inversion = S5H1409_INVERSION_OFF,
.status_mode = S5H1409_DEMODLOCKING,
.mpeg_timing = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK,
};
static struct xc5000_config pinnacle_pctv_hd_800i_tuner_config = {
.i2c_address = 0x64,
.if_khz = 5380,
......@@ -457,9 +466,12 @@ static struct zl10353_config cx88_geniatech_x8000_mt = {
static int attach_xc3028(u8 addr, struct cx8802_dev *dev)
{
struct dvb_frontend *fe;
struct xc2028_ctrl ctl;
struct xc2028_config cfg = {
.i2c_adap = &dev->core->i2c_adap,
.i2c_addr = addr,
.ctrl = &ctl,
.callback = cx88_tuner_callback,
};
if (!dev->dvb.frontend) {
......@@ -469,6 +481,13 @@ static int attach_xc3028(u8 addr, struct cx8802_dev *dev)
return -EINVAL;
}
/*
* Some xc3028 devices may be hidden by an I2C gate. This is known
* to happen with some s5h1409-based devices.
* Now that I2C gate is open, sets up xc3028 configuration
*/
cx88_setup_xc3028(dev->core, &ctl);
fe = dvb_attach(xc2028_attach, dev->dvb.frontend, &cfg);
if (!fe) {
printk(KERN_ERR "%s/2: xc3028 attach failed\n",
......@@ -810,7 +829,7 @@ static int dvb_register(struct cx8802_dev *dev)
return -EINVAL;
break;
case CX88_BOARD_GENIATECH_X8000_MT:
dev->ts_gen_cntrl = 0x00;
dev->ts_gen_cntrl = 0x00;
dev->dvb.frontend = dvb_attach(zl10353_attach,
&cx88_geniatech_x8000_mt,
......@@ -818,6 +837,13 @@ static int dvb_register(struct cx8802_dev *dev)
if (attach_xc3028(0x61, dev) < 0)
return -EINVAL;
break;
case CX88_BOARD_KWORLD_ATSC_120:
dev->dvb.frontend = dvb_attach(s5h1409_attach,
&kworld_atsc_120_config,
&dev->core->i2c_adap);
if (attach_xc3028(0x61, dev) < 0)
return -EINVAL;
break;
default:
printk(KERN_ERR "%s/2: The frontend of your DVB/ATSC card isn't supported yet\n",
dev->core->name);
......
......@@ -37,6 +37,7 @@
#include "btcx-risc.h"
#include "cx88-reg.h"
#include "tuner-xc2028.h"
#include <linux/version.h>
#include <linux/mutex.h>
......@@ -219,6 +220,7 @@ extern struct sram_channel cx88_sram_channels[];
#define CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO 64
#define CX88_BOARD_DVICO_FUSIONHDTV_7_GOLD 65
#define CX88_BOARD_PROLINK_PV_8000GT 66
#define CX88_BOARD_KWORLD_ATSC_120 67
enum cx88_itype {
CX88_VMUX_COMPOSITE1 = 1,
......@@ -603,6 +605,7 @@ extern int cx88_tuner_callback(void *dev, int command, int arg);
extern int cx88_get_resources(const struct cx88_core *core,
struct pci_dev *pci);
extern struct cx88_core *cx88_core_create(struct pci_dev *pci, int nr);
extern void cx88_setup_xc3028(struct cx88_core *core, struct xc2028_ctrl *ctl);
/* ----------------------------------------------------------- */
/* cx88-tvaudio.c */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment