media: i2c: Add TDA1997x HDMI receiver driver

Add support for the TDA1997x HDMI receivers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix type 'testin' -> 'testing']
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

drivers/media/i2c/Kconfig

@@ -56,6 +56,15 @@ config VIDEO_TDA9840
 	  To compile this driver as a module, choose M here: the
 	  module will be called tda9840.
 
+config VIDEO_TDA1997X
+	tristate "NXP TDA1997x HDMI receiver"
+	depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API
+	---help---
+	  V4L2 subdevice driver for the NXP TDA1997x HDMI receivers.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called tda1997x.
+
 config VIDEO_TEA6415C
 	tristate "Philips TEA6415C audio processor"
 	depends on I2C

drivers/media/i2c/Makefile

@@ -13,6 +13,7 @@ obj-$(CONFIG_VIDEO_TVAUDIO) += tvaudio.o
 obj-$(CONFIG_VIDEO_TDA7432) += tda7432.o
 obj-$(CONFIG_VIDEO_SAA6588) += saa6588.o
 obj-$(CONFIG_VIDEO_TDA9840) += tda9840.o
+obj-$(CONFIG_VIDEO_TDA1997X) += tda1997x.o
 obj-$(CONFIG_VIDEO_TEA6415C) += tea6415c.o
 obj-$(CONFIG_VIDEO_TEA6420) += tea6420.o
 obj-$(CONFIG_VIDEO_SAA7110) += saa7110.o

include/media/i2c/tda1997x.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * tda1997x - NXP HDMI receiver
+ *
+ * Copyright 2017 Tim Harvey <tharvey@gateworks.com>
+ *
+ */
+
+#ifndef _TDA1997X_
+#define _TDA1997X_
+
+/* Platform Data */
+struct tda1997x_platform_data {
+	enum v4l2_mbus_type vidout_bus_type;
+	u32 vidout_bus_width;
+	u8 vidout_port_cfg[9];
+	/* pin polarity (1=invert) */
+	bool vidout_inv_de;
+	bool vidout_inv_hs;
+	bool vidout_inv_vs;
+	bool vidout_inv_pclk;
+	/* clock delays (0=-8, 1=-7 ... 15=+7 pixels) */
+	u8 vidout_delay_hs;
+	u8 vidout_delay_vs;
+	u8 vidout_delay_de;
+	u8 vidout_delay_pclk;
+	/* sync selections (controls how sync pins are derived) */
+	u8 vidout_sel_hs;
+	u8 vidout_sel_vs;
+	u8 vidout_sel_de;
+
+	/* Audio Port Output */
+	int audout_format;
+	u32 audout_mclk_fs;	/* clock multiplier */
+	u32 audout_width;	/* 13 or 32 bit */
+	u32 audout_layout;	/* layout0=AP0 layout1=AP0,AP1,AP2,AP3 */
+	bool audout_layoutauto;	/* audio layout dictated by pkt header */
+	bool audout_invert_clk;	/* data valid on rising edge of BCLK */
+	bool audio_auto_mute;	/* enable hardware audio auto-mute */
+};
+
+#endif