Blackfin: net2272: move pin setup to boards files

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -408,6 +408,9 @@ static struct resource net2272_bfin_resources[] = {
 		.start = 0x20300000,
 		.end = 0x20300000 + 0x100,
 		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 1,
+		.flags = IORESOURCE_BUS,
 	}, {
 		.start = IRQ_PF7,
 		.end = IRQ_PF7,

arch/blackfin/mach-bf533/boards/stamp.c

@@ -79,6 +79,9 @@ static struct resource net2272_bfin_resources[] = {
 		.start = 0x20300000,
 		.end = 0x20300000 + 0x100,
 		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 1,
+		.flags = IORESOURCE_BUS,
 	}, {
 		.start = IRQ_PF10,
 		.end = IRQ_PF10,
@@ -659,6 +662,41 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	/* Set PF0 to 0, PF1 to 1 make /AMS3 work properly */
+	ret = gpio_request(GPIO_PF0, "net2272");
+	if (ret)
+		return ret;
+
+	ret = gpio_request(GPIO_PF1, "net2272");
+	if (ret) {
+		gpio_free(GPIO_PF0);
+		return ret;
+	}
+
+	ret = gpio_request(GPIO_PF11, "net2272");
+	if (ret) {
+		gpio_free(GPIO_PF0);
+		gpio_free(GPIO_PF1);
+		return ret;
+	}
+
+	gpio_direction_output(GPIO_PF0, 0);
+	gpio_direction_output(GPIO_PF1, 1);
+
+	/* Reset the USB chip */
+	gpio_direction_output(GPIO_PF11, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PF11, 1);
+#endif
+
+	return 0;
+}
+
 static int __init stamp_init(void)
 {
 	int ret;
@@ -685,6 +723,9 @@ static int __init stamp_init(void)
 	}
 #endif
 
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 	return 0;
 }

arch/blackfin/mach-bf537/boards/cm_bf537e.c

@@ -766,6 +766,24 @@ static struct platform_device *cm_bf537e_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PG14, "net2272");
+	if (ret)
+		return ret;
+
+	/* Reset USB Chip, PG14 */
+	gpio_direction_output(GPIO_PG14, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PG14, 1);
+#endif
+
+	return 0;
+}
+
 static int __init cm_bf537e_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
@@ -777,6 +795,10 @@ static int __init cm_bf537e_init(void)
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
+
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	return 0;
 }
 

arch/blackfin/mach-bf537/boards/cm_bf537u.c

@@ -731,6 +731,36 @@ static struct platform_device *cm_bf537u_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PH15, driver_name);
+	if (ret)
+		return ret;
+
+	ret = gpio_request(GPIO_PH13, "net2272");
+	if (ret) {
+		gpio_free(GPIO_PH15);
+		return ret;
+	}
+
+	/* Set PH15 Low make /AMS2 work properly */
+	gpio_direction_output(GPIO_PH15, 0);
+
+	/* enable CLKBUF output */
+	bfin_write_VR_CTL(bfin_read_VR_CTL() | CLKBUFOE);
+
+	/* Reset the USB chip */
+	gpio_direction_output(GPIO_PH13, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PH13, 1);
+#endif
+
+	return 0;
+}
+
 static int __init cm_bf537u_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
@@ -742,6 +772,10 @@ static int __init cm_bf537u_init(void)
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
+
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	return 0;
 }
 

arch/blackfin/mach-bf537/boards/stamp.c

@@ -366,6 +366,9 @@ static struct resource net2272_bfin_resources[] = {
 		.start = 0x20300000,
 		.end = 0x20300000 + 0x100,
 		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 1,
+		.flags = IORESOURCE_BUS,
 	}, {
 		.start = IRQ_PF7,
 		.end = IRQ_PF7,
@@ -2916,6 +2919,24 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PF6, "net2272");
+	if (ret)
+		return ret;
+
+	/* Reset the USB chip */
+	gpio_direction_output(GPIO_PF6, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PF6, 1);
+#endif
+
+	return 0;
+}
+
 static int __init stamp_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
@@ -2926,6 +2947,9 @@ static int __init stamp_init(void)
 				ARRAY_SIZE(bfin_i2c_board_info));
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	return 0;
 }
 

arch/blackfin/mach-bf537/boards/tcm_bf537.c

@@ -733,6 +733,24 @@ static struct platform_device *cm_bf537_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PG14, "net2272");
+	if (ret)
+		return ret;
+
+	/* Reset USB Chip, PG14 */
+	gpio_direction_output(GPIO_PG14, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PG14, 1);
+#endif
+
+	return 0;
+}
+
 static int __init tcm_bf537_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
@@ -744,6 +762,10 @@ static int __init tcm_bf537_init(void)
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
+
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	return 0;
 }
 

arch/blackfin/mach-bf561/boards/cm_bf561.c

@@ -532,6 +532,24 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PF46, "net2272");
+	if (ret)
+		return ret;
+
+	/* Reset USB Chip, PF46 */
+	gpio_direction_output(GPIO_PF46, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PF46, 1);
+#endif
+
+	return 0;
+}
+
 static int __init cm_bf561_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
@@ -543,6 +561,10 @@ static int __init cm_bf561_init(void)
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
+
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	return 0;
 }
 

arch/blackfin/mach-bf561/boards/ezkit.c

@@ -107,6 +107,9 @@ static struct resource net2272_bfin_resources[] = {
 		.start = 0x2C000000,
 		.end = 0x2C000000 + 0x7F,
 		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 1,
+		.flags = IORESOURCE_BUS,
 	}, {
 		.start = IRQ_PF10,
 		.end = IRQ_PF10,
@@ -516,6 +519,24 @@ static struct platform_device *ezkit_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PF11, "net2272");
+	if (ret)
+		return ret;
+
+	/* Reset the USB chip */
+	gpio_direction_output(GPIO_PF11, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PF11, 1);
+#endif
+
+	return 0;
+}
+
 static int __init ezkit_init(void)
 {
 	int ret;
@@ -542,6 +563,9 @@ static int __init ezkit_init(void)
 	udelay(400);
 #endif
 
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 	return 0;
 }