mtd: diskonchip: remove unused entries in Kconfig

This patch proposes to remove kernel configuration parameters
defined in drivers/mtd/devices/Kconfig, but used nowhere
in the makefiles and source code (except in comments).
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

drivers/mtd/devices/Kconfig

@@ -224,59 +224,4 @@ config BCH_CONST_T
 	default 4
 endif
 
-config MTD_DOCPROBE
-	tristate
-	select MTD_DOCECC
-
-config MTD_DOCECC
-	tristate
-
-config MTD_DOCPROBE_ADVANCED
-	bool "Advanced detection options for DiskOnChip"
-	depends on MTD_DOCPROBE
-	help
-	  This option allows you to specify nonstandard address at which to
-	  probe for a DiskOnChip, or to change the detection options.  You
-	  are unlikely to need any of this unless you are using LinuxBIOS.
-	  Say 'N'.
-
-config MTD_DOCPROBE_ADDRESS
-	hex "Physical address of DiskOnChip" if MTD_DOCPROBE_ADVANCED
-	depends on MTD_DOCPROBE
-	default "0x0"
-	---help---
-	  By default, the probe for DiskOnChip devices will look for a
-	  DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
-	  This option allows you to specify a single address at which to probe
-	  for the device, which is useful if you have other devices in that
-	  range which get upset when they are probed.
-
-	  (Note that on PowerPC, the normal probe will only check at
-	  0xE4000000.)
-
-	  Normally, you should leave this set to zero, to allow the probe at
-	  the normal addresses.
-
-config MTD_DOCPROBE_HIGH
-	bool "Probe high addresses"
-	depends on MTD_DOCPROBE_ADVANCED
-	help
-	  By default, the probe for DiskOnChip devices will look for a
-	  DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
-	  This option changes to make it probe between 0xFFFC8000 and
-	  0xFFFEE000.  Unless you are using LinuxBIOS, this is unlikely to be
-	  useful to you.  Say 'N'.
-
-config MTD_DOCPROBE_55AA
-	bool "Probe for 0x55 0xAA BIOS Extension Signature"
-	depends on MTD_DOCPROBE_ADVANCED
-	help
-	  Check for the 0x55 0xAA signature of a DiskOnChip, and do not
-	  continue with probing if it is absent.  The signature will always be
-	  present for a DiskOnChip 2000 or a normal DiskOnChip Millennium.
-	  Only if you have overwritten the first block of a DiskOnChip
-	  Millennium will it be absent.  Enable this option if you are using
-	  LinuxBIOS or if you need to recover a DiskOnChip Millennium on which
-	  you have managed to wipe the first block.
-
 endmenu

drivers/mtd/nand/diskonchip.c

@@ -46,13 +46,13 @@ static unsigned long __initdata doc_locations[] = {
 	0xfffd8000, 0xfffda000, 0xfffdc000, 0xfffde000,
 	0xfffe0000, 0xfffe2000, 0xfffe4000, 0xfffe6000,
 	0xfffe8000, 0xfffea000, 0xfffec000, 0xfffee000,
-#else /*  CONFIG_MTD_DOCPROBE_HIGH */
+#else
 	0xc8000, 0xca000, 0xcc000, 0xce000,
 	0xd0000, 0xd2000, 0xd4000, 0xd6000,
 	0xd8000, 0xda000, 0xdc000, 0xde000,
 	0xe0000, 0xe2000, 0xe4000, 0xe6000,
 	0xe8000, 0xea000, 0xec000, 0xee000,
-#endif /*  CONFIG_MTD_DOCPROBE_HIGH */
+#endif
 #endif
 	0xffffffff };