Merge branch 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata updates from Tejun Heo:

 - Hannes's patchset implements support for better error reporting
   introduced by the new ATA command spec.

 - the deperecated pci_ dma API usages have been replaced by dma_ ones.

 - a bunch of hardware specific updates and some cleanups.

* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata: remove deprecated use of pci api
  ahci: st: st_configure_oob must be called after IP is clocked.
  ahci: st: Update the ahci_st DT documentation
  ahci: st: Update the DT example for how to obtain the PHY.
  sata_dwc_460ex: indent an if statement
  libata: Add tracepoints
  libata-eh: Set 'information' field for autosense
  libata: Implement support for sense data reporting
  libata: Implement NCQ autosense
  libata: use status bit definitions in ata_dump_status()
  ide,ata: Rename ATA_IDX to ATA_SENSE
  libata: whitespace fixes in ata_to_sense_error()
  libata: whitespace cleanup in ata_get_cmd_descript()
  libata: use READ_LOG_DMA_EXT
  libata: remove ATA_FLAG_LOWTAG
  sata_dwc_460ex: re-use hsdev->dev instead of dwc_dev
  sata_dwc_460ex: move to generic DMA driver
  sata_dwc_460ex: join messages back
  sata: xgene: add ACPI support for APM X-Gene SATA ports
  ata: sata_mv: add proper definitions for LP_PHY_CTL register values

Documentation/devicetree/bindings/ata/ahci-st.txt

@@ -3,29 +3,48 @@ STMicroelectronics STi SATA controller
 This binding describes a SATA device.
 
 Required properties:
- - compatible	   : Must be "st,sti-ahci"
+ - compatible	   : Must be "st,ahci"
  - reg		   : Physical base addresses and length of register sets
  - interrupts	   : Interrupt associated with the SATA device
  - interrupt-names :   Associated name must be; "hostc"
- - resets	   : The power-down and soft-reset lines of SATA IP
- - reset-names	   :   Associated names must be; "pwr-dwn" and "sw-rst"
  - clocks	   : The phandle for the clock
  - clock-names	   :   Associated name must be; "ahci_clk"
- - phys		   : The phandle for the PHY device
+ - phys		   : The phandle for the PHY port
  - phy-names	   :   Associated name must be; "ahci_phy"
 
+Optional properties:
+ - resets	   : The power-down, soft-reset and power-reset lines of SATA IP
+ - reset-names	   :   Associated names must be; "pwr-dwn", "sw-rst" and "pwr-rst"
+
 Example:
 
+	/* Example for stih416 */
 	sata0: sata@fe380000 {
-		compatible      = "st,sti-ahci";
-		reg             = <0xfe380000 0x1000>;
-		interrupts      = <GIC_SPI 157 IRQ_TYPE_NONE>;
-		interrupt-names = "hostc";
-		phys	        = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>;
-		phy-names       = "ahci_phy";
-		resets	        = <&powerdown STIH416_SATA0_POWERDOWN>,
+		compatible	= "st,ahci";
+		reg		= <0xfe380000 0x1000>;
+		interrupts	= <GIC_SPI 157 IRQ_TYPE_NONE>;
+		interrupt-names	= "hostc";
+		phys		= <&phy_port0 PHY_TYPE_SATA>;
+		phy-names	= "ahci_phy";
+		resets		= <&powerdown STIH416_SATA0_POWERDOWN>,
 				  <&softreset STIH416_SATA0_SOFTRESET>;
-		reset-names     = "pwr-dwn", "sw-rst";
-		clocks	        = <&clk_s_a0_ls CLK_ICN_REG>;
-		clock-names     = "ahci_clk";
+		reset-names	= "pwr-dwn", "sw-rst";
+		clocks		= <&clk_s_a0_ls CLK_ICN_REG>;
+		clock-names	= "ahci_clk";
+	};
+
+	/* Example for stih407 family silicon */
+	sata0: sata@9b20000 {
+		compatible	= "st,ahci";
+		reg		= <0x9b20000 0x1000>;
+		interrupts	= <GIC_SPI 159 IRQ_TYPE_NONE>;
+		interrupt-names	= "hostc";
+		phys		= <&phy_port0 PHY_TYPE_SATA>;
+		phy-names	= "ahci_phy";
+		resets		= <&powerdown STIH407_SATA0_POWERDOWN>,
+				  <&softreset STIH407_SATA0_SOFTRESET>,
+				  <&softreset STIH407_SATA0_PWR_SOFTRESET>;
+		reset-names	= "pwr-dwn", "sw-rst", "pwr-rst";
+		clocks		= <&clk_s_c0_flexgen CLK_ICN_REG>;
+		clock-names	= "ahci_clk";
 	};

drivers/ata/Makefile

@@ -111,7 +111,8 @@ obj-$(CONFIG_ATA_GENERIC)	+= ata_generic.o
 # Should be last libata driver
 obj-$(CONFIG_PATA_LEGACY)	+= pata_legacy.o
 
-libata-y	:= libata-core.o libata-scsi.o libata-eh.o libata-transport.o
+libata-y	:= libata-core.o libata-scsi.o libata-eh.o \
+	libata-transport.o libata-trace.o
 libata-$(CONFIG_ATA_SFF)	+= libata-sff.o
 libata-$(CONFIG_SATA_PMP)	+= libata-pmp.o
 libata-$(CONFIG_ATA_ACPI)	+= libata-acpi.o

drivers/ata/acard-ahci.c

@@ -181,10 +181,10 @@ static int acard_ahci_configure_dma_masks(struct pci_dev *pdev, int using_dac)
 	int rc;
 
 	if (using_dac &&
-	    !pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+	    !dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) {
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
 		if (rc) {
-			rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+			rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 			if (rc) {
 				dev_err(&pdev->dev,
 					   "64-bit DMA enable failed\n");
@@ -192,12 +192,12 @@ static int acard_ahci_configure_dma_masks(struct pci_dev *pdev, int using_dac)
 			}
 		}
 	} else {
-		rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev, "32-bit DMA enable failed\n");
 			return rc;
 		}
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev,
 				"32-bit consistent DMA enable failed\n");

drivers/ata/ahci.c

@@ -738,10 +738,10 @@ static int ahci_configure_dma_masks(struct pci_dev *pdev, int using_dac)
 		return 0;
 
 	if (using_dac &&
-	    !pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+	    !dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) {
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
 		if (rc) {
-			rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+			rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 			if (rc) {
 				dev_err(&pdev->dev,
 					"64-bit DMA enable failed\n");
@@ -749,12 +749,12 @@ static int ahci_configure_dma_masks(struct pci_dev *pdev, int using_dac)
 			}
 		}
 	} else {
-		rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev, "32-bit DMA enable failed\n");
 			return rc;
 		}
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev,
 				"32-bit consistent DMA enable failed\n");

drivers/ata/ahci_st.c

@@ -68,8 +68,6 @@ static int st_ahci_deassert_resets(struct device *dev)
 		}
 	}
 
-	st_ahci_configure_oob(drv_data->hpriv->mmio);
-
 	if (drv_data->sw_rst) {
 		err = reset_control_deassert(drv_data->sw_rst);
 		if (err) {
@@ -172,6 +170,8 @@ static int st_ahci_probe(struct platform_device *pdev)
 	if (err)
 		return err;
 
+	st_ahci_configure_oob(drv_data->hpriv->mmio);
+
 	err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info,
 				      &ahci_platform_sht);
 	if (err) {
@@ -222,6 +222,8 @@ static int st_ahci_resume(struct device *dev)
 		return err;
 	}
 
+	st_ahci_configure_oob(drv_data->hpriv->mmio);
+
 	return ahci_platform_resume_host(dev);
 }
 #endif

drivers/ata/ahci_xgene.c

@@ -22,6 +22,7 @@
  * NOTE: PM support is not currently available.
  *
  */
+#include <linux/acpi.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/ahci_platform.h>
@@ -718,6 +719,14 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 	return rc;
 }
 
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id xgene_ahci_acpi_match[] = {
+	{ "APMC0D0D", },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, xgene_ahci_acpi_match);
+#endif
+
 static const struct of_device_id xgene_ahci_of_match[] = {
 	{.compatible = "apm,xgene-ahci"},
 	{},
@@ -730,6 +739,7 @@ static struct platform_driver xgene_ahci_driver = {
 	.driver = {
 		.name = DRV_NAME,
 		.of_match_table = xgene_ahci_of_match,
+		.acpi_match_table = ACPI_PTR(xgene_ahci_acpi_match),
 	},
 };
 

drivers/ata/libata-core.c

@@ -70,6 +70,9 @@
 #include <linux/pm_runtime.h>
 #include <linux/platform_device.h>
 
+#define CREATE_TRACE_POINTS
+#include <trace/events/libata.h>
+
 #include "libata.h"
 #include "libata-transport.h"
 
@@ -691,11 +694,11 @@ static int ata_rwcmd_protocol(struct ata_taskfile *tf, struct ata_device *dev)
  *	RETURNS:
  *	Block address read from @tf.
  */
-u64 ata_tf_read_block(struct ata_taskfile *tf, struct ata_device *dev)
+u64 ata_tf_read_block(const struct ata_taskfile *tf, struct ata_device *dev)
 {
 	u64 block = 0;
 
-	if (tf->flags & ATA_TFLAG_LBA) {
+	if (!dev || tf->flags & ATA_TFLAG_LBA) {
 		if (tf->flags & ATA_TFLAG_LBA48) {
 			block |= (u64)tf->hob_lbah << 40;
 			block |= (u64)tf->hob_lbam << 32;
@@ -2144,6 +2147,24 @@ static int ata_dev_config_ncq(struct ata_device *dev,
 	return 0;
 }
 
+static void ata_dev_config_sense_reporting(struct ata_device *dev)
+{
+	unsigned int err_mask;
+
+	if (!ata_id_has_sense_reporting(dev->id))
+		return;
+
+	if (ata_id_sense_reporting_enabled(dev->id))
+		return;
+
+	err_mask = ata_dev_set_feature(dev, SETFEATURE_SENSE_DATA, 0x1);
+	if (err_mask) {
+		ata_dev_dbg(dev,
+			    "failed to enable Sense Data Reporting, Emask 0x%x\n",
+			    err_mask);
+	}
+}
+
 /**
  *	ata_dev_configure - Configure the specified ATA/ATAPI device
  *	@dev: Target device to configure
@@ -2366,7 +2387,7 @@ int ata_dev_configure(struct ata_device *dev)
 					dev->devslp_timing[i] = sata_setting[j];
 				}
 		}
-
+		ata_dev_config_sense_reporting(dev);
 		dev->cdb_len = 16;
 	}
 
@@ -4897,6 +4918,7 @@ void ata_qc_complete(struct ata_queued_cmd *qc)
 		 */
 		if (unlikely(ata_tag_internal(qc->tag))) {
 			fill_result_tf(qc);
+			trace_ata_qc_complete_internal(qc);
 			__ata_qc_complete(qc);
 			return;
 		}
@@ -4907,6 +4929,7 @@ void ata_qc_complete(struct ata_queued_cmd *qc)
 		 */
 		if (unlikely(qc->flags & ATA_QCFLAG_FAILED)) {
 			fill_result_tf(qc);
+			trace_ata_qc_complete_failed(qc);
 			ata_qc_schedule_eh(qc);
 			return;
 		}
@@ -4917,6 +4940,7 @@ void ata_qc_complete(struct ata_queued_cmd *qc)
 		if (qc->flags & ATA_QCFLAG_RESULT_TF)
 			fill_result_tf(qc);
 
+		trace_ata_qc_complete_done(qc);
 		/* Some commands need post-processing after successful
 		 * completion.
 		 */
@@ -5064,7 +5088,7 @@ void ata_qc_issue(struct ata_queued_cmd *qc)
 	}
 
 	ap->ops->qc_prep(qc);
-
+	trace_ata_qc_issue(qc);
 	qc->err_mask |= ap->ops->qc_issue(qc);
 	if (unlikely(qc->err_mask))
 		goto err;

drivers/ata/libata-scsi.c

@@ -270,13 +270,28 @@ DEVICE_ATTR(unload_heads, S_IRUGO | S_IWUSR,
 	    ata_scsi_park_show, ata_scsi_park_store);
 EXPORT_SYMBOL_GPL(dev_attr_unload_heads);
 
-static void ata_scsi_set_sense(struct scsi_cmnd *cmd, u8 sk, u8 asc, u8 ascq)
+void ata_scsi_set_sense(struct scsi_cmnd *cmd, u8 sk, u8 asc, u8 ascq)
 {
+	if (!cmd)
+		return;
+
 	cmd->result = (DRIVER_SENSE << 24) | SAM_STAT_CHECK_CONDITION;
 
 	scsi_build_sense_buffer(0, cmd->sense_buffer, sk, asc, ascq);
 }
 
+void ata_scsi_set_sense_information(struct scsi_cmnd *cmd,
+				    const struct ata_taskfile *tf)
+{
+	u64 information;
+
+	if (!cmd)
+		return;
+
+	information = ata_tf_read_block(tf, NULL);
+	scsi_set_sense_information(cmd->sense_buffer, information);
+}
+
 static ssize_t
 ata_scsi_em_message_store(struct device *dev, struct device_attribute *attr,
 			  const char *buf, size_t count)
@@ -799,26 +814,27 @@ static void ata_dump_status(unsigned id, struct ata_taskfile *tf)
 	if (stat & ATA_BUSY) {
 		printk("Busy }\n");	/* Data is not valid in this case */
 	} else {
-		if (stat & 0x40)	printk("DriveReady ");
-		if (stat & 0x20)	printk("DeviceFault ");
-		if (stat & 0x10)	printk("SeekComplete ");
-		if (stat & 0x08)	printk("DataRequest ");
-		if (stat & 0x04)	printk("CorrectedError ");
-		if (stat & 0x02)	printk("Index ");
-		if (stat & 0x01)	printk("Error ");
+		if (stat & ATA_DRDY)	printk("DriveReady ");
+		if (stat & ATA_DF)	printk("DeviceFault ");
+		if (stat & ATA_DSC)	printk("SeekComplete ");
+		if (stat & ATA_DRQ)	printk("DataRequest ");
+		if (stat & ATA_CORR)	printk("CorrectedError ");
+		if (stat & ATA_SENSE)	printk("Sense ");
+		if (stat & ATA_ERR)	printk("Error ");
 		printk("}\n");
 
 		if (err) {
 			printk(KERN_WARNING "ata%u: error=0x%02x { ", id, err);
-			if (err & 0x04)		printk("DriveStatusError ");
-			if (err & 0x80) {
-				if (err & 0x04)	printk("BadCRC ");
+			if (err & ATA_ABORTED)	printk("DriveStatusError ");
+			if (err & ATA_ICRC) {
+				if (err & ATA_ABORTED)
+						printk("BadCRC ");
 				else		printk("Sector ");
 			}
-			if (err & 0x40)		printk("UncorrectableError ");
-			if (err & 0x10)		printk("SectorIdNotFound ");
-			if (err & 0x02)		printk("TrackZeroNotFound ");
-			if (err & 0x01)		printk("AddrMarkNotFound ");
+			if (err & ATA_UNC)	printk("UncorrectableError ");
+			if (err & ATA_IDNF)	printk("SectorIdNotFound ");
+			if (err & ATA_TRK0NF)	printk("TrackZeroNotFound ");
+			if (err & ATA_AMNF)	printk("AddrMarkNotFound ");
 			printk("}\n");
 		}
 	}
@@ -849,40 +865,59 @@ static void ata_to_sense_error(unsigned id, u8 drv_stat, u8 drv_err, u8 *sk,
 	/* Based on the 3ware driver translation table */
 	static const unsigned char sense_table[][4] = {
 		/* BBD|ECC|ID|MAR */
-		{0xd1, 		ABORTED_COMMAND, 0x00, 0x00}, 	// Device busy                  Aborted command
+		{0xd1,		ABORTED_COMMAND, 0x00, 0x00},
+			// Device busy                  Aborted command
 		/* BBD|ECC|ID */
-		{0xd0,  	ABORTED_COMMAND, 0x00, 0x00}, 	// Device busy                  Aborted command
+		{0xd0,		ABORTED_COMMAND, 0x00, 0x00},
+			// Device busy                  Aborted command
 		/* ECC|MC|MARK */
-		{0x61, 		HARDWARE_ERROR, 0x00, 0x00}, 	// Device fault                 Hardware error
+		{0x61,		HARDWARE_ERROR, 0x00, 0x00},
+			// Device fault                 Hardware error
 		/* ICRC|ABRT */		/* NB: ICRC & !ABRT is BBD */
-		{0x84, 		ABORTED_COMMAND, 0x47, 0x00}, 	// Data CRC error               SCSI parity error
+		{0x84,		ABORTED_COMMAND, 0x47, 0x00},
+			// Data CRC error               SCSI parity error
 		/* MC|ID|ABRT|TRK0|MARK */
-		{0x37, 		NOT_READY, 0x04, 0x00}, 	// Unit offline                 Not ready
+		{0x37,		NOT_READY, 0x04, 0x00},
+			// Unit offline                 Not ready
 		/* MCR|MARK */
-		{0x09, 		NOT_READY, 0x04, 0x00}, 	// Unrecovered disk error       Not ready
+		{0x09,		NOT_READY, 0x04, 0x00},
+			// Unrecovered disk error       Not ready
 		/*  Bad address mark */
-		{0x01, 		MEDIUM_ERROR, 0x13, 0x00}, 	// Address mark not found       Address mark not found for data field
-		/* TRK0 */
-		{0x02, 		HARDWARE_ERROR, 0x00, 0x00}, 	// Track 0 not found		Hardware error
+		{0x01,		MEDIUM_ERROR, 0x13, 0x00},
+			// Address mark not found for data field
+		/* TRK0 - Track 0 not found */
+		{0x02,		HARDWARE_ERROR, 0x00, 0x00},
+			// Hardware error
 		/* Abort: 0x04 is not translated here, see below */
 		/* Media change request */
-		{0x08, 		NOT_READY, 0x04, 0x00}, 	// Media change request	  FIXME: faking offline
-		/* SRV/IDNF */
-		{0x10, 		ILLEGAL_REQUEST, 0x21, 0x00}, 	// ID not found                 Logical address out of range
-		/* MC */
-		{0x20, 		UNIT_ATTENTION, 0x28, 0x00}, 	// Media Changed		Not ready to ready change, medium may have changed
-		/* ECC */
-		{0x40, 		MEDIUM_ERROR, 0x11, 0x04}, 	// Uncorrectable ECC error      Unrecovered read error
+		{0x08,		NOT_READY, 0x04, 0x00},
+			// FIXME: faking offline
+		/* SRV/IDNF - ID not found */
+		{0x10,		ILLEGAL_REQUEST, 0x21, 0x00},
+			// Logical address out of range
+		/* MC - Media Changed */
+		{0x20,		UNIT_ATTENTION, 0x28, 0x00},
+			// Not ready to ready change, medium may have changed
+		/* ECC - Uncorrectable ECC error */
+		{0x40,		MEDIUM_ERROR, 0x11, 0x04},
+			// Unrecovered read error
 		/* BBD - block marked bad */
-		{0x80, 		MEDIUM_ERROR, 0x11, 0x04}, 	// Block marked bad		Medium error, unrecovered read error
+		{0x80,		MEDIUM_ERROR, 0x11, 0x04},
+			// Block marked bad	Medium error, unrecovered read error
 		{0xFF, 0xFF, 0xFF, 0xFF}, // END mark
 	};
 	static const unsigned char stat_table[][4] = {
 		/* Must be first because BUSY means no other bits valid */
-		{0x80, 		ABORTED_COMMAND, 0x47, 0x00},	// Busy, fake parity for now
-		{0x20, 		HARDWARE_ERROR,  0x44, 0x00}, 	// Device fault, internal target failure
-		{0x08, 		ABORTED_COMMAND, 0x47, 0x00},	// Timed out in xfer, fake parity for now
-		{0x04, 		RECOVERED_ERROR, 0x11, 0x00},	// Recovered ECC error	  Medium error, recovered
+		{0x80,		ABORTED_COMMAND, 0x47, 0x00},
+		// Busy, fake parity for now
+		{0x40,		ILLEGAL_REQUEST, 0x21, 0x04},
+		// Device ready, unaligned write command
+		{0x20,		HARDWARE_ERROR,  0x44, 0x00},
+		// Device fault, internal target failure
+		{0x08,		ABORTED_COMMAND, 0x47, 0x00},
+		// Timed out in xfer, fake parity for now
+		{0x04,		RECOVERED_ERROR, 0x11, 0x00},
+		// Recovered ECC error	  Medium error, recovered
 		{0xFF, 0xFF, 0xFF, 0xFF}, // END mark
 	};
 
@@ -1757,7 +1792,9 @@ static void ata_scsi_qc_complete(struct ata_queued_cmd *qc)
 	    ((cdb[2] & 0x20) || need_sense)) {
 		ata_gen_passthru_sense(qc);
 	} else {
-		if (!need_sense) {
+		if (qc->flags & ATA_QCFLAG_SENSE_VALID) {
+			cmd->result = SAM_STAT_CHECK_CONDITION;
+		} else if (!need_sense) {
 			cmd->result = SAM_STAT_GOOD;
 		} else {
 			/* TODO: decide which descriptor format to use
@@ -4240,10 +4277,7 @@ int ata_sas_allocate_tag(struct ata_port *ap)
 	unsigned int i, tag;
 
 	for (i = 0, tag = ap->sas_last_tag + 1; i < max_queue; i++, tag++) {
-		if (ap->flags & ATA_FLAG_LOWTAG)
-			tag = 1;
-		else
-			tag = tag < max_queue ? tag : 0;
+		tag = tag < max_queue ? tag : 0;
 
 		/* the last tag is reserved for internal command. */
 		if (tag == ATA_TAG_INTERNAL)

drivers/ata/libata-sff.c

@@ -3220,11 +3220,11 @@ void ata_pci_bmdma_init(struct ata_host *host)
 	 * ->sff_irq_clear method.  Try to initialize bmdma_addr
 	 * regardless of dma masks.
 	 */
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		ata_bmdma_nodma(host, "failed to set dma mask");
 	if (!rc) {
-		rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+		rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 		if (rc)
 			ata_bmdma_nodma(host,
 					"failed to set consistent dma mask");

drivers/ata/libata-trace.c

+/*
+ * libata-trace.c - trace functions for libata
+ *
+ * Copyright 2015 Hannes Reinecke
+ * Copyright 2015 SUSE Linux GmbH
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2, or (at your option)
+ *  any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; see the file COPYING.  If not, write to
+ *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/trace_seq.h>
+#include <trace/events/libata.h>
+
+const char *
+libata_trace_parse_status(struct trace_seq *p, unsigned char status)
+{
+	const char *ret = trace_seq_buffer_ptr(p);
+
+	trace_seq_printf(p, "{ ");
+	if (status & ATA_BUSY)
+		trace_seq_printf(p, "BUSY ");
+	if (status & ATA_DRDY)
+		trace_seq_printf(p, "DRDY ");
+	if (status & ATA_DF)
+		trace_seq_printf(p, "DF ");
+	if (status & ATA_DSC)
+		trace_seq_printf(p, "DSC ");
+	if (status & ATA_DRQ)
+		trace_seq_printf(p, "DRQ ");
+	if (status & ATA_CORR)
+		trace_seq_printf(p, "CORR ");
+	if (status & ATA_SENSE)
+		trace_seq_printf(p, "SENSE ");
+	if (status & ATA_ERR)
+		trace_seq_printf(p, "ERR ");
+	trace_seq_putc(p, '}');
+	trace_seq_putc(p, 0);
+
+	return ret;
+}
+
+const char *
+libata_trace_parse_eh_action(struct trace_seq *p, unsigned int eh_action)
+{
+	const char *ret = trace_seq_buffer_ptr(p);
+
+	trace_seq_printf(p, "%x", eh_action);
+	if (eh_action) {
+		trace_seq_printf(p, "{ ");
+		if (eh_action & ATA_EH_REVALIDATE)
+			trace_seq_printf(p, "REVALIDATE ");
+		if (eh_action & (ATA_EH_SOFTRESET | ATA_EH_HARDRESET))
+			trace_seq_printf(p, "RESET ");
+		else if (eh_action & ATA_EH_SOFTRESET)
+			trace_seq_printf(p, "SOFTRESET ");
+		else if (eh_action & ATA_EH_HARDRESET)
+			trace_seq_printf(p, "HARDRESET ");
+		if (eh_action & ATA_EH_ENABLE_LINK)
+			trace_seq_printf(p, "ENABLE_LINK ");
+		if (eh_action & ATA_EH_PARK)
+			trace_seq_printf(p, "PARK ");
+		trace_seq_putc(p, '}');
+	}
+	trace_seq_putc(p, 0);
+
+	return ret;
+}
+
+const char *
+libata_trace_parse_eh_err_mask(struct trace_seq *p, unsigned int eh_err_mask)
+{
+	const char *ret = trace_seq_buffer_ptr(p);
+
+	trace_seq_printf(p, "%x", eh_err_mask);
+	if (eh_err_mask) {
+		trace_seq_printf(p, "{ ");
+		if (eh_err_mask & AC_ERR_DEV)
+			trace_seq_printf(p, "DEV ");
+		if (eh_err_mask & AC_ERR_HSM)
+			trace_seq_printf(p, "HSM ");
+		if (eh_err_mask & AC_ERR_TIMEOUT)
+			trace_seq_printf(p, "TIMEOUT ");
+		if (eh_err_mask & AC_ERR_MEDIA)
+			trace_seq_printf(p, "MEDIA ");
+		if (eh_err_mask & AC_ERR_ATA_BUS)
+			trace_seq_printf(p, "ATA_BUS ");
+		if (eh_err_mask & AC_ERR_HOST_BUS)
+			trace_seq_printf(p, "HOST_BUS ");
+		if (eh_err_mask & AC_ERR_SYSTEM)
+			trace_seq_printf(p, "SYSTEM ");
+		if (eh_err_mask & AC_ERR_INVALID)
+			trace_seq_printf(p, "INVALID ");
+		if (eh_err_mask & AC_ERR_OTHER)
+			trace_seq_printf(p, "OTHER ");
+		if (eh_err_mask & AC_ERR_NODEV_HINT)
+			trace_seq_printf(p, "NODEV_HINT ");
+		if (eh_err_mask & AC_ERR_NCQ)
+			trace_seq_printf(p, "NCQ ");
+		trace_seq_putc(p, '}');
+	}
+	trace_seq_putc(p, 0);
+
+	return ret;
+}
+
+const char *
+libata_trace_parse_qc_flags(struct trace_seq *p, unsigned int qc_flags)
+{
+	const char *ret = trace_seq_buffer_ptr(p);
+
+	trace_seq_printf(p, "%x", qc_flags);
+	if (qc_flags) {
+		trace_seq_printf(p, "{ ");
+		if (qc_flags & ATA_QCFLAG_ACTIVE)
+			trace_seq_printf(p, "ACTIVE ");
+		if (qc_flags & ATA_QCFLAG_DMAMAP)
+			trace_seq_printf(p, "DMAMAP ");
+		if (qc_flags & ATA_QCFLAG_IO)
+			trace_seq_printf(p, "IO ");
+		if (qc_flags & ATA_QCFLAG_RESULT_TF)
+			trace_seq_printf(p, "RESULT_TF ");
+		if (qc_flags & ATA_QCFLAG_CLEAR_EXCL)
+			trace_seq_printf(p, "CLEAR_EXCL ");
+		if (qc_flags & ATA_QCFLAG_QUIET)
+			trace_seq_printf(p, "QUIET ");
+		if (qc_flags & ATA_QCFLAG_RETRY)
+			trace_seq_printf(p, "RETRY ");
+		if (qc_flags & ATA_QCFLAG_FAILED)
+			trace_seq_printf(p, "FAILED ");
+		if (qc_flags & ATA_QCFLAG_SENSE_VALID)
+			trace_seq_printf(p, "SENSE_VALID ");
+		if (qc_flags & ATA_QCFLAG_EH_SCHEDULED)
+			trace_seq_printf(p, "EH_SCHEDULED ");
+		trace_seq_putc(p, '}');
+	}
+	trace_seq_putc(p, 0);
+
+	return ret;
+}

drivers/ata/libata.h

@@ -67,7 +67,8 @@ extern struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev, int tag);
 extern int ata_build_rw_tf(struct ata_taskfile *tf, struct ata_device *dev,
 			   u64 block, u32 n_block, unsigned int tf_flags,
 			   unsigned int tag);
-extern u64 ata_tf_read_block(struct ata_taskfile *tf, struct ata_device *dev);
+extern u64 ata_tf_read_block(const struct ata_taskfile *tf,
+			     struct ata_device *dev);
 extern unsigned ata_exec_internal(struct ata_device *dev,
 				  struct ata_taskfile *tf, const u8 *cdb,
 				  int dma_dir, void *buf, unsigned int buflen,
@@ -137,6 +138,9 @@ extern int ata_scsi_add_hosts(struct ata_host *host,
 			      struct scsi_host_template *sht);
 extern void ata_scsi_scan_host(struct ata_port *ap, int sync);
 extern int ata_scsi_offline_dev(struct ata_device *dev);
+extern void ata_scsi_set_sense(struct scsi_cmnd *cmd, u8 sk, u8 asc, u8 ascq);
+extern void ata_scsi_set_sense_information(struct scsi_cmnd *cmd,
+					   const struct ata_taskfile *tf);
 extern void ata_scsi_media_change_notify(struct ata_device *dev);
 extern void ata_scsi_hotplug(struct work_struct *work);
 extern void ata_schedule_scsi_eh(struct Scsi_Host *shost);

drivers/ata/pata_atp867x.c

@@ -475,11 +475,11 @@ static int atp867x_ata_pci_sff_init_host(struct ata_host *host)
 
 	atp867x_fixup(host);
 
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	return rc;
 }
 

drivers/ata/pata_cs5520.c

@@ -164,11 +164,11 @@ static int cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 		return -ENODEV;
 	}
 
-	if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
+	if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(32))) {
 		printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
 		return -ENODEV;
 	}
-	if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) {
+	if (dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32))) {
 		printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
 		return -ENODEV;
 	}

drivers/ata/pata_hpt3x3.c

@@ -221,10 +221,10 @@ static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	if (rc)
 		return rc;
 	host->iomap = pcim_iomap_table(pdev);
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 

drivers/ata/pata_ninja32.c

@@ -122,10 +122,10 @@ static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 		return rc;
 
 	host->iomap = pcim_iomap_table(dev);
-	rc = pci_set_dma_mask(dev, ATA_DMA_MASK);
+	rc = dma_set_mask(&dev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(dev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&dev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 	pci_set_master(dev);

drivers/ata/pata_pdc2027x.c

@@ -730,11 +730,11 @@ static int pdc2027x_init_one(struct pci_dev *pdev,
 		return rc;
 	host->iomap = pcim_iomap_table(pdev);
 
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 

drivers/ata/pata_scc.c

@@ -1029,10 +1029,10 @@ static int scc_host_init(struct ata_host *host)
 	if (rc)
 		return rc;
 
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 

drivers/ata/pata_sil680.c

@@ -374,10 +374,10 @@ static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	host->iomap = pcim_iomap_table(pdev);
 
 	/* Setup DMA masks */
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 	pci_set_master(pdev);

drivers/ata/pdc_adma.c

@@ -593,12 +593,12 @@ static int adma_set_dma_masks(struct pci_dev *pdev, void __iomem *mmio_base)
 {
 	int rc;
 
-	rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+	rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 	if (rc) {
 		dev_err(&pdev->dev, "32-bit DMA enable failed\n");
 		return rc;
 	}
-	rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+	rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 	if (rc) {
 		dev_err(&pdev->dev, "32-bit consistent DMA enable failed\n");
 		return rc;

drivers/ata/sata_inic162x.c

@@ -856,13 +856,13 @@ static int inic_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	}
 
 	/* Set dma_mask.  This devices doesn't support 64bit addressing. */
-	rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+	rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 	if (rc) {
 		dev_err(&pdev->dev, "32-bit DMA enable failed\n");
 		return rc;
 	}
 
-	rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+	rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 	if (rc) {
 		dev_err(&pdev->dev, "32-bit consistent DMA enable failed\n");
 		return rc;

drivers/ata/sata_mv.c

@@ -306,6 +306,11 @@ enum {
 	MV5_PHY_CTL		= 0x0C,
 	SATA_IFCFG		= 0x050,
 	LP_PHY_CTL		= 0x058,
+	LP_PHY_CTL_PIN_PU_PLL   = (1 << 0),
+	LP_PHY_CTL_PIN_PU_RX    = (1 << 1),
+	LP_PHY_CTL_PIN_PU_TX    = (1 << 2),
+	LP_PHY_CTL_GEN_TX_3G    = (1 << 5),
+	LP_PHY_CTL_GEN_RX_3G    = (1 << 9),
 
 	MV_M2_PREAMP_MASK	= 0x7e0,
 
@@ -1391,10 +1396,17 @@ static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val)
 				/*
 				 * Set PHY speed according to SControl speed.
 				 */
-				if ((val & 0xf0) == 0x10)
-					writelfl(0x7, lp_phy_addr);
-				else
-					writelfl(0x227, lp_phy_addr);
+				u32 lp_phy_val =
+					LP_PHY_CTL_PIN_PU_PLL |
+					LP_PHY_CTL_PIN_PU_RX  |
+					LP_PHY_CTL_PIN_PU_TX;
+
+				if ((val & 0xf0) != 0x10)
+					lp_phy_val |=
+						LP_PHY_CTL_GEN_TX_3G |
+						LP_PHY_CTL_GEN_RX_3G;
+
+				writelfl(lp_phy_val, lp_phy_addr);
 			}
 		}
 		writelfl(val, addr);
@@ -4308,10 +4320,10 @@ static int pci_go_64(struct pci_dev *pdev)
 {
 	int rc;
 
-	if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+	if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) {
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
 		if (rc) {
-			rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+			rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 			if (rc) {
 				dev_err(&pdev->dev,
 					"64-bit DMA enable failed\n");
@@ -4319,12 +4331,12 @@ static int pci_go_64(struct pci_dev *pdev)
 			}
 		}
 	} else {
-		rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev, "32-bit DMA enable failed\n");
 			return rc;
 		}
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev,
 				"32-bit consistent DMA enable failed\n");

drivers/ata/sata_nv.c

@@ -756,10 +756,10 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
 			blk_queue_bounce_limit(sdev1->request_queue,
 					       ATA_DMA_MASK);
 
-		pci_set_dma_mask(pdev, ATA_DMA_MASK);
+		dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	} else {
 		/** This shouldn't fail as it was set to this value before */
-		pci_set_dma_mask(pdev, pp->adma_dma_mask);
+		dma_set_mask(&pdev->dev, pp->adma_dma_mask);
 		if (sdev0)
 			blk_queue_bounce_limit(sdev0->request_queue,
 					       pp->adma_dma_mask);
@@ -1133,10 +1133,10 @@ static int nv_adma_port_start(struct ata_port *ap)
 
 	/* Ensure DMA mask is set to 32-bit before allocating legacy PRD and
 	   pad buffers */
-	rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+	rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+	rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 	if (rc)
 		return rc;
 
@@ -1161,8 +1161,8 @@ static int nv_adma_port_start(struct ata_port *ap)
 	   These are allowed to fail since we store the value that ends up
 	   being used to set as the bounce limit in slave_config later if
 	   needed. */
-	pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
-	pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+	dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
+	dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
 	pp->adma_dma_mask = *dev->dma_mask;
 
 	mem = dmam_alloc_coherent(dev, NV_ADMA_PORT_PRIV_DMA_SZ,

drivers/ata/sata_promise.c

@@ -1246,10 +1246,10 @@ static int pdc_ata_init_one(struct pci_dev *pdev,
 	/* initialize adapter */
 	pdc_host_init(host);
 
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 

drivers/ata/sata_qstor.c

@@ -557,10 +557,10 @@ static int qs_set_dma_masks(struct pci_dev *pdev, void __iomem *mmio_base)
 	int rc, have_64bit_bus = (bus_info & QS_HPHY_64BIT);
 
 	if (have_64bit_bus &&
-	    !pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+	    !dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) {
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
 		if (rc) {
-			rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+			rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 			if (rc) {
 				dev_err(&pdev->dev,
 					"64-bit DMA enable failed\n");
@@ -568,12 +568,12 @@ static int qs_set_dma_masks(struct pci_dev *pdev, void __iomem *mmio_base)
 			}
 		}
 	} else {
-		rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev, "32-bit DMA enable failed\n");
 			return rc;
 		}
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev,
 				"32-bit consistent DMA enable failed\n");

drivers/ata/sata_sil.c

@@ -770,10 +770,10 @@ static int sil_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 		return rc;
 	host->iomap = pcim_iomap_table(pdev);
 
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 

drivers/ata/sata_sil24.c

@@ -246,7 +246,7 @@ enum {
 	/* host flags */
 	SIL24_COMMON_FLAGS	= ATA_FLAG_SATA | ATA_FLAG_PIO_DMA |
 				  ATA_FLAG_NCQ | ATA_FLAG_ACPI_SATA |
-				  ATA_FLAG_AN | ATA_FLAG_PMP | ATA_FLAG_LOWTAG,
+				  ATA_FLAG_AN | ATA_FLAG_PMP,
 	SIL24_FLAG_PCIX_IRQ_WOC	= (1 << 24), /* IRQ loss errata on PCI-X */
 
 	IRQ_STAT_4PORTS		= 0xf,
@@ -1312,10 +1312,10 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	host->iomap = iomap;
 
 	/* configure and activate the device */
-	if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+	if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) {
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
 		if (rc) {
-			rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+			rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 			if (rc) {
 				dev_err(&pdev->dev,
 					"64-bit DMA enable failed\n");
@@ -1323,12 +1323,12 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 			}
 		}
 	} else {
-		rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev, "32-bit DMA enable failed\n");
 			return rc;
 		}
-		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+		rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 		if (rc) {
 			dev_err(&pdev->dev,
 				"32-bit consistent DMA enable failed\n");

drivers/ata/sata_svw.c

@@ -496,10 +496,10 @@ static int k2_sata_init_one(struct pci_dev *pdev, const struct pci_device_id *en
 		ata_port_pbar_desc(ap, 5, offset, "port");
 	}
 
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 

drivers/ata/sata_sx4.c

@@ -1476,10 +1476,10 @@ static int pdc_sata_init_one(struct pci_dev *pdev,
 	}
 
 	/* configure and activate */
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 

drivers/ata/sata_via.c

@@ -502,10 +502,10 @@ static int vt6421_prepare_host(struct pci_dev *pdev, struct ata_host **r_host)
 	for (i = 0; i < host->n_ports; i++)
 		vt6421_init_addrs(host->ports[i]);
 
-	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
 	if (rc)
 		return rc;
 

drivers/ata/sata_vsc.c

@@ -387,10 +387,10 @@ static int vsc_sata_init_one(struct pci_dev *pdev,
 	/*
 	 * Use 32 bit DMA mask, because 64 bit address support is poor.
 	 */
-	rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+	rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
 	if (rc)
 		return rc;
-	rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+	rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
 	if (rc)
 		return rc;
 

drivers/ide/ide-lib.c

@@ -148,8 +148,8 @@ u8 ide_dump_status(ide_drive_t *drive, const char *msg, u8 stat)
 			printk(KERN_CONT "DataRequest ");
 		if (stat & ATA_CORR)
 			printk(KERN_CONT "CorrectedError ");
-		if (stat & ATA_IDX)
-			printk(KERN_CONT "Index ");
+		if (stat & ATA_SENSE)
+			printk(KERN_CONT "Sense ");
 		if (stat & ATA_ERR)
 			printk(KERN_CONT "Error ");
 	}

drivers/ide/ide-probe.c

@@ -273,7 +273,7 @@ int ide_dev_read_id(ide_drive_t *drive, u8 cmd, u16 *id, int irq_ctx)
 	    (hwif->host_flags & IDE_HFLAG_BROKEN_ALTSTATUS) == 0) {
 		a = tp_ops->read_altstatus(hwif);
 		s = tp_ops->read_status(hwif);
-		if ((a ^ s) & ~ATA_IDX)
+		if ((a ^ s) & ~ATA_SENSE)
 			/* ancient Seagate drives, broken interfaces */
 			printk(KERN_INFO "%s: probing with STATUS(0x%02x) "
 					 "instead of ALTSTATUS(0x%02x)\n",

drivers/scsi/scsi_error.c

@@ -26,6 +26,7 @@
 #include <linux/blkdev.h>
 #include <linux/delay.h>
 #include <linux/jiffies.h>
+#include <asm/unaligned.h>
 
 #include <scsi/scsi.h>
 #include <scsi/scsi_cmnd.h>
@@ -2586,3 +2587,33 @@ void scsi_build_sense_buffer(int desc, u8 *buf, u8 key, u8 asc, u8 ascq)
 	}
 }
 EXPORT_SYMBOL(scsi_build_sense_buffer);
+
+/**
+ * scsi_set_sense_information - set the information field in a
+ *		formatted sense data buffer
+ * @buf:	Where to build sense data
+ * @info:	64-bit information value to be set
+ *
+ **/
+void scsi_set_sense_information(u8 *buf, u64 info)
+{
+	if ((buf[0] & 0x7f) == 0x72) {
+		u8 *ucp, len;
+
+		len = buf[7];
+		ucp = (char *)scsi_sense_desc_find(buf, len + 8, 0);
+		if (!ucp) {
+			buf[7] = len + 0xa;
+			ucp = buf + 8 + len;
+		}
+		ucp[0] = 0;
+		ucp[1] = 0xa;
+		ucp[2] = 0x80; /* Valid bit */
+		ucp[3] = 0;
+		put_unaligned_be64(info, &ucp[4]);
+	} else if ((buf[0] & 0x7f) == 0x70) {
+		buf[0] |= 0x80;
+		put_unaligned_be64(info, &buf[3]);
+	}
+}
+EXPORT_SYMBOL(scsi_set_sense_information);

include/linux/ata.h

@@ -94,6 +94,8 @@ enum {
 	ATA_ID_SECTOR_SIZE	= 106,
 	ATA_ID_WWN		= 108,
 	ATA_ID_LOGICAL_SECTOR_SIZE	= 117,	/* and 118 */
+	ATA_ID_COMMAND_SET_3	= 119,
+	ATA_ID_COMMAND_SET_4	= 120,
 	ATA_ID_LAST_LUN		= 126,
 	ATA_ID_DLF		= 128,
 	ATA_ID_CSFO		= 129,
@@ -177,7 +179,7 @@ enum {
 	ATA_DSC			= (1 << 4),	/* drive seek complete */
 	ATA_DRQ			= (1 << 3),	/* data request i/o */
 	ATA_CORR		= (1 << 2),	/* corrected data error */
-	ATA_IDX			= (1 << 1),	/* index */
+	ATA_SENSE		= (1 << 1),	/* sense code available */
 	ATA_ERR			= (1 << 0),	/* have an error */
 	ATA_SRST		= (1 << 2),	/* software reset */
 	ATA_ICRC		= (1 << 7),	/* interface CRC error */
@@ -382,6 +384,8 @@ enum {
 	SATA_SSP		= 0x06,	/* Software Settings Preservation */
 	SATA_DEVSLP		= 0x09,	/* Device Sleep */
 
+	SETFEATURE_SENSE_DATA = 0xC3, /* Sense Data Reporting feature */
+
 	/* feature values for SET_MAX */
 	ATA_SET_MAX_ADDR	= 0x00,
 	ATA_SET_MAX_PASSWD	= 0x01,
@@ -525,6 +529,8 @@ struct ata_bmdma_prd {
 #define ata_id_cdb_intr(id)	(((id)[ATA_ID_CONFIG] & 0x60) == 0x20)
 #define ata_id_has_da(id)	((id)[ATA_ID_SATA_CAPABILITY_2] & (1 << 4))
 #define ata_id_has_devslp(id)	((id)[ATA_ID_FEATURE_SUPP] & (1 << 8))
+#define ata_id_has_ncq_autosense(id) \
+				((id)[ATA_ID_FEATURE_SUPP] & (1 << 7))
 
 static inline bool ata_id_has_hipm(const u16 *id)
 {
@@ -696,6 +702,27 @@ static inline bool ata_id_wcache_enabled(const u16 *id)
 	return id[ATA_ID_CFS_ENABLE_1] & (1 << 5);
 }
 
+static inline bool ata_id_has_read_log_dma_ext(const u16 *id)
+{
+	if (!(id[ATA_ID_CFS_ENABLE_2] & (1 << 15)))
+		return false;
+	return id[ATA_ID_COMMAND_SET_3] & (1 << 3);
+}
+
+static inline bool ata_id_has_sense_reporting(const u16 *id)
+{
+	if (!(id[ATA_ID_CFS_ENABLE_2] & (1 << 15)))
+		return false;
+	return id[ATA_ID_COMMAND_SET_3] & (1 << 6);
+}
+
+static inline bool ata_id_sense_reporting_enabled(const u16 *id)
+{
+	if (!(id[ATA_ID_CFS_ENABLE_2] & (1 << 15)))
+		return false;
+	return id[ATA_ID_COMMAND_SET_4] & (1 << 6);
+}
+
 /**
  *	ata_id_major_version	-	get ATA level of drive
  *	@id: Identify data

include/linux/libata.h

@@ -231,8 +231,7 @@ enum {
 	ATA_FLAG_SW_ACTIVITY	= (1 << 22), /* driver supports sw activity
 					      * led */
 	ATA_FLAG_NO_DIPM	= (1 << 23), /* host not happy with DIPM */
-	ATA_FLAG_LOWTAG		= (1 << 24), /* host wants lowest available tag */
-	ATA_FLAG_SAS_HOST	= (1 << 25), /* SAS host */
+	ATA_FLAG_SAS_HOST	= (1 << 24), /* SAS host */
 
 	/* bits 24:31 of ap->flags are reserved for LLD specific flags */
 

include/scsi/scsi_eh.h

@@ -59,6 +59,7 @@ extern int scsi_get_sense_info_fld(const u8 * sense_buffer, int sb_len,
 				   u64 * info_out);
 
 extern void scsi_build_sense_buffer(int desc, u8 *buf, u8 key, u8 asc, u8 ascq);
+extern void scsi_set_sense_information(u8 *buf, u64 info);
 
 extern int scsi_ioctl_reset(struct scsi_device *, int __user *);