Skip to content

L
linux
Commit a20b40ff authored by Linus Torvalds's avatar Linus Torvalds
Browse files
Options

Merge bk://kernel.bkbits.net/davem/net-2.5 

into home.transmeta.com:/home/torvalds/v2.5/linux
parents 5e1dcb06 5ae2c9cf
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 4687 additions and 1806 deletions
Documentation/networking/e100.txt
View file @ a20b40ff
Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
==============================================================
September 16, 2002
November 19, 2002
Contents
......@@ -19,7 +19,7 @@ In This Release
===============
This file describes the Linux* Base Driver for the Intel(R) PRO/100 Family of
Adapters, version 2.1.x. This driver includes support for Itanium(TM)-based
Adapters, version 2.2.x. This driver includes support for Itanium(TM)-based
systems.
......@@ -94,8 +94,9 @@ For the latest Intel PRO/100 network driver for Linux, see:
Command Line Parameters
=======================
The following optional parameters are used by entering them on the command
line with the modprobe or insmod command using this syntax:
If the driver is built as a module, the following optional parameters are
used by entering them on the command line with the modprobe or insmod command
using this syntax:
modprobe e100 [<option>=<VAL1>,<VAL2>,...]
......
Documentation/networking/e1000.txt
View file @ a20b40ff
This diff is collapsed.
MAINTAINERS
View file @ a20b40ff
......@@ -923,10 +923,11 @@ M: scott.feldman@intel.com
S: Supported
INTEL PRO/1000 GIGABIT ETHERNET SUPPORT
P: Chris Leech
M: christopher.leech@intel.com
P: Jeb Cramer
M: cramerj@intel.com
P: Scott Feldman
M: scott.feldman@intel.com
W: http://sourceforge.net/projects/e1000/
S: Supported
INTERMEZZO FILE SYSTEM
......
arch/i386/kernel/entry.S
View file @ a20b40ff
......@@ -73,10 +73,10 @@ NT_MASK = 0x00004000
VM_MASK = 0x00020000
/*
* ESP0 is at offset 4. 0x100 is the size of the TSS, and
* ESP0 is at offset 4. 0x200 is the size of the TSS, and
* also thus the top-of-stack pointer offset of SYSENTER_ESP
*/
TSS_ESP0_OFFSET = (4 - 0x100)
TSS_ESP0_OFFSET = (4 - 0x200)
#ifdef CONFIG_PREEMPT
#define preempt_stop cli
......@@ -479,23 +479,32 @@ device_not_available_emulate:
* by hand onto the new stack - while updating the return eip past
* the instruction that would have done it for sysenter.
*/
#define CHECK_SYSENTER_EIP \
cmpl $sysenter_entry,(%esp); \
jne 1f; \
movl TSS_ESP0_OFFSET+12(%esp),%esp; \
#define FIX_STACK(offset, ok, label) \
cmpw $__KERNEL_CS,4(%esp); \
jne ok; \
label: \
movl TSS_ESP0_OFFSET+offset(%esp),%esp; \
pushfl; \
pushl $__KERNEL_CS; \
pushl $sysenter_past_esp; \
1:
pushl $sysenter_past_esp
ENTRY(debug)
CHECK_SYSENTER_EIP
cmpl $sysenter_entry,(%esp)
jne debug_stack_correct
FIX_STACK(12, debug_stack_correct, debug_esp_fix_insn)
debug_stack_correct:
pushl $0
pushl $do_debug
jmp error_code
ENTRY(nmi)
CHECK_SYSENTER_EIP
cmpl $sysenter_entry,(%esp)
je nmi_stack_fixup
cmpl $debug - 1,(%esp)
jle nmi_stack_correct
cmpl $debug_esp_fix_insn,(%esp)
jle nmi_debug_stack_fixup
nmi_stack_correct:
pushl %eax
SAVE_ALL
movl %esp, %edx
......@@ -505,6 +514,13 @@ ENTRY(nmi)
addl $8, %esp
RESTORE_ALL
nmi_stack_fixup:
FIX_STACK(12,nmi_stack_correct, 1)
jmp nmi_stack_correct
nmi_debug_stack_fixup:
FIX_STACK(24,nmi_stack_correct, 1)
jmp nmi_stack_correct
ENTRY(int3)
pushl $0
pushl $do_int3
......
arch/sparc/kernel/traps.c
View file @ a20b40ff
......@@ -89,6 +89,7 @@ void instruction_dump (unsigned long *pc)
void die_if_kernel(char *str, struct pt_regs *regs)
{
static int die_counter;
int count = 0;
/* Amuse the user. */
......@@ -98,7 +99,7 @@ void die_if_kernel(char *str, struct pt_regs *regs)
" /_| \\__/ |_\\\n"
" \\__U_/\n");
printk("%s(%d): %s\n", current->comm, current->pid, str);
printk("%s(%d): %s [#%d]\n", current->comm, current->pid, str, ++die_counter);
show_regs(regs);
__SAVE; __SAVE; __SAVE; __SAVE;
......
arch/sparc64/kernel/head.S
View file @ a20b40ff
......@@ -671,7 +671,9 @@ set_worklist:
#endif
/* Kill PROM timer */
wr %g0, 0, %tick_cmpr
sethi %hi(0x80000000), %g1
sllx %g1, 32, %g1
wr %g1, 0, %tick_cmpr
BRANCH_IF_ANY_CHEETAH(g1,g5,1f)
......
arch/sparc64/kernel/irq.c
View file @ a20b40ff
......@@ -719,12 +719,8 @@ void handler_irq(int irq, struct pt_regs *regs)
*/
{
unsigned long clr_mask = 1 << irq;
unsigned long tick_mask;
unsigned long tick_mask = tick_ops->softint_mask;
if (SPARC64_USE_STICK)
tick_mask = (1UL << 16);
else
tick_mask = (1UL << 0);
if ((irq == 14) && (get_softint() & tick_mask)) {
irq = 0;
clr_mask = tick_mask;
......@@ -946,113 +942,6 @@ int probe_irq_off(unsigned long mask)
return 0;
}
/* This is gets the master TICK_INT timer going. */
void sparc64_init_timers(void (*cfunc)(int, void *, struct pt_regs *),
unsigned long *clock)
{
unsigned long pstate;
extern unsigned long timer_tick_offset;
int node, err;
#ifdef CONFIG_SMP
extern void smp_tick_init(void);
#endif
if (!SPARC64_USE_STICK) {
node = linux_cpus[0].prom_node;
*clock = prom_getint(node, "clock-frequency");
} else {
node = prom_root_node;
*clock = prom_getint(node, "stick-frequency");
}
timer_tick_offset = *clock / HZ;
#ifdef CONFIG_SMP
smp_tick_init();
#endif
/* Register IRQ handler. */
err = request_irq(build_irq(0, 0, 0UL, 0UL), cfunc, SA_STATIC_ALLOC,
"timer", NULL);
if (err) {
prom_printf("Serious problem, cannot register TICK_INT\n");
prom_halt();
}
/* Guarentee that the following sequences execute
* uninterrupted.
*/
__asm__ __volatile__("rdpr %%pstate, %0\n\t"
"wrpr %0, %1, %%pstate"
: "=r" (pstate)
: "i" (PSTATE_IE));
/* Set things up so user can access tick register for profiling
* purposes. Also workaround BB_ERRATA_1 by doing a dummy
* read back of %tick after writing it.
*/
__asm__ __volatile__(
" sethi %%hi(0x80000000), %%g1\n"
" ba,pt %%xcc, 1f\n"
" sllx %%g1, 32, %%g1\n"
" .align 64\n"
"1: rd %%tick, %%g2\n"
" add %%g2, 6, %%g2\n"
" andn %%g2, %%g1, %%g2\n"
" wrpr %%g2, 0, %%tick\n"
" rdpr %%tick, %%g0"
: /* no outputs */
: /* no inputs */
: "g1", "g2");
/* Workaround for Spitfire Errata (#54 I think??), I discovered
* this via Sun BugID 4008234, mentioned in Solaris-2.5.1 patch
* number 103640.
*
* On Blackbird writes to %tick_cmpr can fail, the
* workaround seems to be to execute the wr instruction
* at the start of an I-cache line, and perform a dummy
* read back from %tick_cmpr right after writing to it. -DaveM
*/
if (!SPARC64_USE_STICK) {
__asm__ __volatile__(
" rd %%tick, %%g1\n"
" ba,pt %%xcc, 1f\n"
" add %%g1, %0, %%g1\n"
" .align 64\n"
"1: wr %%g1, 0x0, %%tick_cmpr\n"
" rd %%tick_cmpr, %%g0"
: /* no outputs */
: "r" (timer_tick_offset)
: "g1");
} else {
/* Let the user get at STICK too. */
__asm__ __volatile__(
" sethi %%hi(0x80000000), %%g1\n"
" sllx %%g1, 32, %%g1\n"
" rd %%asr24, %%g2\n"
" andn %%g2, %%g1, %%g2\n"
" wr %%g2, 0, %%asr24"
: /* no outputs */
: /* no inputs */
: "g1", "g2");
__asm__ __volatile__(
" rd %%asr24, %%g1\n"
" add %%g1, %0, %%g1\n"
" wr %%g1, 0x0, %%asr25"
: /* no outputs */
: "r" (timer_tick_offset)
: "g1");
}
/* Restore PSTATE_IE. */
__asm__ __volatile__("wrpr %0, 0x0, %%pstate"
: /* no outputs */
: "r" (pstate));
local_irq_enable();
}
#ifdef CONFIG_SMP
static int retarget_one_irq(struct irqaction *p, int goal_cpu)
{
......
arch/sparc64/kernel/smp.c
View file @ a20b40ff
This diff is collapsed.
arch/sparc64/kernel/sparc64_ksyms.c
View file @ a20b40ff
......@@ -128,20 +128,13 @@ EXPORT_SYMBOL(__write_unlock);
#endif
/* Hard IRQ locking */
#ifdef CONFIG_SMP
EXPORT_SYMBOL(synchronize_irq);
#endif
#if defined(CONFIG_MCOUNT)
extern void mcount(void);
EXPORT_SYMBOL_NOVERS(mcount);
#endif
/* Uniprocessor clock frequency */
#ifndef CONFIG_SMP
EXPORT_SYMBOL(up_clock_tick);
#endif
/* Per-CPU information table */
EXPORT_SYMBOL(cpu_data);
......@@ -162,10 +155,13 @@ EXPORT_SYMBOL(_do_write_lock);
EXPORT_SYMBOL(_do_write_unlock);
#endif
#ifdef CONFIG_SMP
EXPORT_SYMBOL(smp_call_function);
#endif
#endif /* CONFIG_SMP */
/* Uniprocessor clock frequency */
#ifndef CONFIG_SMP
extern unsigned long up_clock_tick;
EXPORT_SYMBOL(up_clock_tick);
#endif
/* semaphores */
......
arch/sparc64/kernel/time.c
View file @ a20b40ff
This diff is collapsed.
arch/sparc64/kernel/trampoline.S
View file @ a20b40ff
......@@ -85,7 +85,10 @@ spitfire_startup:
startup_continue:
wrpr %g0, 15, %pil
wr %g0, 0, %tick_cmpr
sethi %hi(0x80000000), %g2
sllx %g2, 32, %g2
wr %g2, 0, %tick_cmpr
/* Call OBP by hand to lock KERNBASE into i/d tlbs. */
mov %o0, %l0
......
arch/sparc64/kernel/traps.c
View file @ a20b40ff
......@@ -33,6 +33,7 @@
#include <asm/chafsr.h>
#include <asm/psrcompat.h>
#include <asm/processor.h>
#include <asm/timer.h>
#ifdef CONFIG_KMOD
#include <linux/kmod.h>
#endif
......@@ -588,7 +589,7 @@ unsigned long __init cheetah_tune_scheduling(void)
flush_linesize = ecache_flush_linesize;
flush_size = ecache_flush_size >> 1;
__asm__ __volatile__("rd %%tick, %0" : "=r" (tick1));
tick1 = tick_ops->get_tick();
__asm__ __volatile__("1: subcc %0, %4, %0\n\t"
" bne,pt %%xcc, 1b\n\t"
......@@ -597,7 +598,7 @@ unsigned long __init cheetah_tune_scheduling(void)
: "0" (flush_size), "r" (flush_base),
"i" (ASI_PHYS_USE_EC), "r" (flush_linesize));
__asm__ __volatile__("rd %%tick, %0" : "=r" (tick2));
tick2 = tick_ops->get_tick();
raw = (tick2 - tick1);
......@@ -1598,6 +1599,7 @@ void show_trace_task(struct task_struct *tsk)
void die_if_kernel(char *str, struct pt_regs *regs)
{
static int die_counter;
extern void __show_regs(struct pt_regs * regs);
extern void smp_report_regs(void);
int count = 0;
......@@ -1610,7 +1612,7 @@ void die_if_kernel(char *str, struct pt_regs *regs)
" /_| \\__/ |_\\\n"
" \\__U_/\n");
printk("%s(%d): %s\n", current->comm, current->pid, str);
printk("%s(%d): %s [#%d]\n", current->comm, current->pid, str, ++die_counter);
__asm__ __volatile__("flushw");
__show_regs(regs);
if (regs->tstate & TSTATE_PRIV) {
......
arch/sparc64/mm/ultra.S
View file @ a20b40ff
......@@ -560,8 +560,8 @@ xcall_flush_tlb_kernel_range:
/* This runs in a very controlled environment, so we do
* not need to worry about BH races etc.
*/
.globl xcall_sync_stick
xcall_sync_stick:
.globl xcall_sync_tick
xcall_sync_tick:
rdpr %pstate, %g2
wrpr %g2, PSTATE_IG | PSTATE_AG, %pstate
rdpr %pil, %g2
......@@ -569,7 +569,7 @@ xcall_sync_stick:
sethi %hi(109f), %g7
b,pt %xcc, etrap_irq
109: or %g7, %lo(109b), %g7
call smp_synchronize_stick_client
call smp_synchronize_tick_client
nop
clr %l6
b rtrap_xcall
......
drivers/net/3c509.c
View file @ a20b40ff
......@@ -56,6 +56,10 @@
v1.19b 08Nov2002 Marc Zyngier <maz@wild-wind.fr.eu.org>
- Introduce driver model for EISA cards.
*/
/*
FIXES for PC-9800:
Shu Iwanaga: 3c569B(PC-9801 C-bus) support
*/
#define DRV_NAME "3c509"
#define DRV_VERSION "1.19b"
......@@ -257,7 +261,7 @@ static struct mca_driver el3_mca_driver = {
};
#endif /* CONFIG_MCA */
#ifdef __ISAPNP__
#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
static struct isapnp_device_id el3_isapnp_adapters[] __initdata = {
{ ISAPNP_ANY_ID, ISAPNP_ANY_ID,
ISAPNP_VENDOR('T', 'C', 'M'), ISAPNP_FUNCTION(0x5090),
......@@ -350,7 +354,7 @@ static void el3_common_remove (struct net_device *dev)
if (lp->pmdev)
pm_unregister(lp->pmdev);
#endif
#ifdef __ISAPNP__
#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
if (lp->type == EL3_PNP)
pnp_device_detach(to_pnp_dev(lp->dev));
#endif
......@@ -368,12 +372,12 @@ static int __init el3_probe(int card_idx)
int ioaddr, irq, if_port;
u16 phys_addr[3];
static int current_tag;
#ifdef __ISAPNP__
#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
static int pnp_cards;
struct pnp_dev *idev = NULL;
#endif /* __ISAPNP__ */
#ifdef __ISAPNP__
#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
if (nopnp == 1)
goto no_pnp;
......@@ -421,6 +425,9 @@ static int __init el3_probe(int card_idx)
no_pnp:
#endif /* __ISAPNP__ */
#ifdef CONFIG_X86_PC9800
id_port = 0x71d0;
#else
/* Select an open I/O location at 0x1*0 to do contention select. */
for ( ; id_port < 0x200; id_port += 0x10) {
if (check_region(id_port, 1))
......@@ -435,6 +442,7 @@ static int __init el3_probe(int card_idx)
printk(" WARNING: No I/O port available for 3c509 activation.\n");
return -ENODEV;
}
#endif /* CONFIG_X86_PC9800 */
/* Next check for all ISA bus boards by sending the ID sequence to the
ID_PORT. We find cards past the first by setting the 'current_tag'
on cards as they are found. Cards with their tag set will not
......@@ -465,7 +473,7 @@ static int __init el3_probe(int card_idx)
phys_addr[i] = htons(id_read_eeprom(i));
}
#ifdef __ISAPNP__
#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
if (nopnp == 0) {
/* The ISA PnP 3c509 cards respond to the ID sequence.
This check is needed in order not to register them twice. */
......@@ -490,9 +498,19 @@ static int __init el3_probe(int card_idx)
{
unsigned int iobase = id_read_eeprom(8);
if_port = iobase >> 14;
#ifdef CONFIG_X86_PC9800
ioaddr = 0x40d0 + ((iobase & 0x1f) << 8);
#else
ioaddr = 0x200 + ((iobase & 0x1f) << 4);
#endif
}
irq = id_read_eeprom(9) >> 12;
#ifdef CONFIG_X86_PC9800
if (irq == 7)
irq = 6;
else if (irq == 15)
irq = 13;
#endif
if (!(dev = init_etherdev(NULL, sizeof(struct el3_private))))
return -ENOMEM;
......@@ -522,7 +540,11 @@ static int __init el3_probe(int card_idx)
outb(0xd0 + ++current_tag, id_port);
/* Activate the adaptor at the EEPROM location. */
#ifdef CONFIG_X86_PC9800
outb((ioaddr >> 8) | 0xe0, id_port);
#else
outb((ioaddr >> 4) | 0xe0, id_port);
#endif
EL3WINDOW(0);
if (inw(ioaddr) != 0x6d50) {
......@@ -534,7 +556,7 @@ static int __init el3_probe(int card_idx)
/* Free the interrupt so that some other card can use it. */
outw(0x0f00, ioaddr + WN0_IRQ);
#ifdef __ISAPNP__
#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
found: /* PNP jumps here... */
#endif /* __ISAPNP__ */
......@@ -543,7 +565,7 @@ static int __init el3_probe(int card_idx)
dev->irq = irq;
dev->if_port = if_port;
lp = dev->priv;
#ifdef __ISAPNP__
#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
lp->dev = &idev->dev;
#endif
......@@ -1388,6 +1410,12 @@ el3_up(struct net_device *dev)
outw(0x0001, ioaddr + 4);
/* Set the IRQ line. */
#ifdef CONFIG_X86_PC9800
if (dev->irq == 6)
dev->irq = 7;
else if (dev->irq == 13)
dev->irq = 15;
#endif
outw((dev->irq << 12) | 0x0f00, ioaddr + WN0_IRQ);
/* Set the station address in window 2 each time opened. */
......@@ -1550,7 +1578,7 @@ MODULE_PARM_DESC(debug, "debug level (0-6)");
MODULE_PARM_DESC(irq, "IRQ number(s) (assigned)");
MODULE_PARM_DESC(xcvr,"transceiver(s) (0=internal, 1=external)");
MODULE_PARM_DESC(max_interrupt_work, "maximum events handled per interrupt");
#ifdef __ISAPNP__
#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
MODULE_PARM(nopnp, "i");
MODULE_PARM_DESC(nopnp, "disable ISA PnP support (0-1)");
MODULE_DEVICE_TABLE(isapnp, el3_isapnp_adapters);
......
drivers/net/8390.h
View file @ a20b40ff
......@@ -123,7 +123,8 @@ struct ei_device {
#define inb_p(port) in_8(port)
#define outb_p(val,port) out_8(port,val)
#elif defined(CONFIG_ARM_ETHERH) || defined(CONFIG_ARM_ETHERH_MODULE)
#elif defined(CONFIG_ARM_ETHERH) || defined(CONFIG_ARM_ETHERH_MODULE) || \
defined(CONFIG_NET_CBUS)
#define EI_SHIFT(x) (ei_local->reg_offset[x])
#else
#define EI_SHIFT(x) (x)
......
drivers/net/Kconfig
View file @ a20b40ff
......@@ -663,7 +663,7 @@ config EL16
as <file:Documentation/networking/net-modules.txt>.
config EL3
tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
tristate "3c509/3c529 (MCA)/3c569B (98)/3c579 \"EtherLink III\" support"
depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
---help---
If you have a network (Ethernet) card belonging to the 3Com
......@@ -932,7 +932,7 @@ config NI65
source "drivers/net/tulip/Kconfig"
config AT1700
tristate "AT1700/1720 support (EXPERIMENTAL)"
tristate "AT1700/1720/RE1000Plus(C-Bus) support (EXPERIMENTAL)"
depends on NET_ETHERNET && (ISA || MCA) && EXPERIMENTAL
---help---
If you have a network (Ethernet) card of this type, say Y and read
......@@ -978,7 +978,7 @@ config HP100
config NET_ISA
bool "Other ISA cards"
depends on NET_ETHERNET && ISA
depends on NET_ETHERNET && ISA && !X86_PC9800
---help---
If your network (Ethernet) card hasn't been mentioned yet and its
bus system (that's the way the cards talks to the other components
......@@ -1176,6 +1176,55 @@ config SK_G16
the Ethernet-HOWTO, available from
<http://www.linuxdoc.org/docs.html#howto>.
config NET_CBUS
bool "NEC PC-9800 C-bus cards"
depends on NET_ETHERNET && ISA && X86_PC9800
---help---
If your network (Ethernet) card hasn't been mentioned yet and its
bus system (that's the way the cards talks to the other components
of your computer) is NEC PC-9800 C-Bus, say Y.
config NE2K_CBUS
tristate "Most NE2000-based Ethernet support"
depends on NET_CBUS
config NE2K_CBUS_EGY98
bool "Melco EGY-98 support"
depends on NE2K_CBUS
config NE2K_CBUS_LGY98
bool "Melco LGY-98 support"
depends on NE2K_CBUS
config NE2K_CBUS_ICM
bool "ICM IF-27xxET support"
depends on NE2K_CBUS
config NE2K_CBUS_IOLA98
bool "I-O DATA LA-98 support"
depends on NE2K_CBUS
config NE2K_CBUS_CNET98EL
bool "Contec C-NET(98)E/L support"
depends on NE2K_CBUS
config NE2K_CBUS_CNET98EL_IO_BASE
hex "C-NET(98)E/L I/O base address (0xaaed or 0x55ed)"
depends on NE2K_CBUS_CNET98EL
default "0xaaed"
config NE2K_CBUS_ATLA98
bool "Allied Telesis LA-98 Support"
depends on NE2K_CBUS
config NE2K_CBUS_BDN
bool "ELECOM Laneed LD-BDN[123]A Support"
depends on NE2K_CBUS
config NE2K_CBUS_NEC108
bool "NEC PC-9801-108 Support"
depends on NE2K_CBUS
config SKMC
tristate "SKnet MCA support"
depends on NET_ETHERNET && MCA
......@@ -1904,6 +1953,7 @@ config E1000
82544 PRO/1000 XF Server Adapter A50484-xxx
82544 PRO/1000 T Desktop Adapter A62947-xxx
82540 PRO/1000 MT Desktop Adapter A78408-xxx
82541 PRO/1000 MT Desktop Adapter C91016-xxx
82545 PRO/1000 MT Server Adapter A92165-xxx
82546 PRO/1000 MT Dual Port Server Adapter A92111-xxx
82545 PRO/1000 MF Server Adapter A91622-xxx
......
drivers/net/Makefile
View file @ a20b40ff
......@@ -81,6 +81,7 @@ obj-$(CONFIG_ARM_ETHERH) += 8390.o
obj-$(CONFIG_WD80x3) += wd.o 8390.o
obj-$(CONFIG_EL2) += 3c503.o 8390.o
obj-$(CONFIG_NE2000) += ne.o 8390.o
obj-$(CONFIG_NE2K_CBUS) += ne2k_cbus.o 8390.o
obj-$(CONFIG_NE2_MCA) += ne2.o 8390.o
obj-$(CONFIG_HPLAN) += hp.o 8390.o
obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390.o
......
drivers/net/Makefile.lib
View file @ a20b40ff
......@@ -19,6 +19,7 @@ obj-$(CONFIG_MACE) += crc32.o
obj-$(CONFIG_MACMACE) += crc32.o
obj-$(CONFIG_MIPS_AU1000_ENET) += crc32.o
obj-$(CONFIG_NATSEMI) += crc32.o
obj-$(CONFIG_NE2K_CBUS) += crc32.o
obj-$(CONFIG_PCMCIA_FMVJ18X) += crc32.o
obj-$(CONFIG_PCMCIA_SMC91C92) += crc32.o
obj-$(CONFIG_PCMCIA_XIRTULIP) += crc32.o
......
drivers/net/Space.c
View file @ a20b40ff
......@@ -233,7 +233,7 @@ static struct devprobe isa_probes[] __initdata = {
#ifdef CONFIG_E2100 /* Cabletron E21xx series. */
{e2100_probe, 0},
#endif
#ifdef CONFIG_NE2000 /* ISA (use ne2k-pci for PCI cards) */
#if defined(CONFIG_NE2000) || defined(CONFIG_NE2K_CBUS) /* ISA & PC-9800 CBUS (use ne2k-pci for PCI cards) */
{ne_probe, 0},
#endif
#ifdef CONFIG_LANCE /* ISA/VLB (use pcnet32 for PCI cards) */
......
drivers/net/at1700.c
View file @ a20b40ff
......@@ -34,6 +34,10 @@
only is it difficult to detect, it also moves around in I/O space in
response to inb()s from other device probes!
*/
/*
99/03/03 Allied Telesis RE1000 Plus support by T.Hagawa
99/12/30 port to 2.3.35 by K.Takai
*/
#include <linux/config.h>
#include <linux/errno.h>
......@@ -76,10 +80,17 @@ static int fmv18x_probe_list[] __initdata = {
* ISA
*/
#ifndef CONFIG_X86_PC9800
static int at1700_probe_list[] __initdata = {
0x260, 0x280, 0x2a0, 0x240, 0x340, 0x320, 0x380, 0x300, 0
};
#else /* CONFIG_X86_PC9800 */
static int at1700_probe_list[] __initdata = {
0x1d6, 0x1d8, 0x1da, 0x1d4, 0xd4, 0xd2, 0xd8, 0xd0, 0
};
#endif /* CONFIG_X86_PC9800 */
/*
* MCA
*/
......@@ -122,6 +133,7 @@ struct net_local {
/* Offsets from the base address. */
#ifndef CONFIG_X86_PC9800
#define STATUS 0
#define TX_STATUS 0
#define RX_STATUS 1
......@@ -136,6 +148,7 @@ struct net_local {
#define TX_START 10
#define COL16CNTL 11 /* Controll Reg for 16 collisions */
#define MODE13 13
#define RX_CTRL 14
/* Configuration registers only on the '865A/B chips. */
#define EEPROM_Ctrl 16
#define EEPROM_Data 17
......@@ -144,8 +157,39 @@ struct net_local {
#define IOCONFIG 18 /* Either read the jumper, or move the I/O. */
#define IOCONFIG1 19
#define SAPROM 20 /* The station address PROM, if no EEPROM. */
#define MODE24 24
#define RESET 31 /* Write to reset some parts of the chip. */
#define AT1700_IO_EXTENT 32
#define PORT_OFFSET(o) (o)
#else /* CONFIG_X86_PC9800 */
#define STATUS (0x0000)
#define TX_STATUS (0x0000)
#define RX_STATUS (0x0001)
#define TX_INTR (0x0200)/* Bit-mapped interrupt enable registers. */
#define RX_INTR (0x0201)
#define TX_MODE (0x0400)
#define RX_MODE (0x0401)
#define CONFIG_0 (0x0600)/* Misc. configuration settings. */
#define CONFIG_1 (0x0601)
/* Run-time register bank 2 definitions. */
#define DATAPORT (0x0800)/* Word-wide DMA or programmed-I/O dataport. */
#define TX_START (0x0a00)
#define COL16CNTL (0x0a01)/* Controll Reg for 16 collisions */
#define MODE13 (0x0c01)
#define RX_CTRL (0x0e00)
/* Configuration registers only on the '865A/B chips. */
#define EEPROM_Ctrl (0x1000)
#define EEPROM_Data (0x1200)
#define CARDSTATUS 16 /* FMV-18x Card Status */
#define CARDSTATUS1 17 /* FMV-18x Card Status */
#define IOCONFIG (0x1400)/* Either read the jumper, or move the I/O. */
#define IOCONFIG1 (0x1600)
#define SAPROM 20 /* The station address PROM, if no EEPROM. */
#define MODE24 (0x1800)/* The station address PROM, if no EEPROM. */
#define RESET (0x1e01)/* Write to reset some parts of the chip. */
#define PORT_OFFSET(o) ({ int _o_ = (o); (_o_ & ~1) * 0x100 + (_o_ & 1); })
#endif /* CONFIG_X86_PC9800 */
#define TX_TIMEOUT 10
......@@ -225,8 +269,20 @@ static int __init at1700_probe1(struct net_device *dev, int ioaddr)
int slot, ret = -ENODEV;
struct net_local *lp;
#ifndef CONFIG_X86_PC9800
if (!request_region(ioaddr, AT1700_IO_EXTENT, dev->name))
return -EBUSY;
#else
for (i = 0; i < 0x2000; i += 0x0200) {
if (!request_region(ioaddr + i, 2, dev->name)) {
while (i > 0) {
i -= 0x0200;
release_region(ioaddr + i, 2);
}
return -EBUSY;
}
}
#endif
/* Resetting the chip doesn't reset the ISA interface, so don't bother.
That means we have to be careful with the register values we probe for.
......@@ -317,10 +373,17 @@ static int __init at1700_probe1(struct net_device *dev, int ioaddr)
/* Reset the internal state machines. */
outb(0, ioaddr + RESET);
if (is_at1700)
if (is_at1700) {
#ifndef CONFIG_X86_PC9800
irq = at1700_irqmap[(read_eeprom(ioaddr, 12)&0x04)
| (read_eeprom(ioaddr, 0)>>14)];
else {
#else
{
char re1000plus_irqmap[4] = {3, 5, 6, 12};
irq = re1000plus_irqmap[inb(ioaddr + IOCONFIG1) >> 6];
}
#endif
} else {
/* Check PnP mode for FMV-183/184/183A/184A. */
/* This PnP routine is very poor. IO and IRQ should be known. */
if (inb(ioaddr + CARDSTATUS1) & 0x20) {
......@@ -392,18 +455,22 @@ static int __init at1700_probe1(struct net_device *dev, int ioaddr)
/* Set the station address in bank zero. */
outb(0x00, ioaddr + CONFIG_1);
for (i = 0; i < 6; i++)
outb(dev->dev_addr[i], ioaddr + 8 + i);
outb(dev->dev_addr[i], ioaddr + PORT_OFFSET(8 + i));
/* Switch to bank 1 and set the multicast table to accept none. */
outb(0x04, ioaddr + CONFIG_1);
for (i = 0; i < 8; i++)
outb(0x00, ioaddr + 8 + i);
outb(0x00, ioaddr + PORT_OFFSET(8 + i));
/* Switch to bank 2 */
/* Lock our I/O address, and set manual processing mode for 16 collisions. */
outb(0x08, ioaddr + CONFIG_1);
#ifndef CONFIG_X86_PC9800
outb(dev->if_port, ioaddr + MODE13);
#else
outb(0, ioaddr + MODE13);
#endif
outb(0x00, ioaddr + COL16CNTL);
if (net_debug)
......@@ -447,7 +514,12 @@ static int __init at1700_probe1(struct net_device *dev, int ioaddr)
kfree(dev->priv);
dev->priv = NULL;
err_out:
#ifndef CONFIG_X86_PC9800
release_region(ioaddr, AT1700_IO_EXTENT);
#else
for (i = 0; i < 0x2000; i += 0x0200)
release_region(ioaddr + i, 2);
#endif
return ret;
}
......@@ -459,7 +531,11 @@ static int __init at1700_probe1(struct net_device *dev, int ioaddr)
#define EE_DATA_READ 0x80 /* EEPROM chip data out, in reg. 17. */
/* Delay between EEPROM clock transitions. */
#ifndef CONFIG_X86_PC9800
#define eeprom_delay() do { } while (0)
#else
#define eeprom_delay() __asm__ ("out%B0 %%al,%0" :: "N"(0x5f))
#endif
/* The EEPROM commands include the alway-set leading bit. */
#define EE_WRITE_CMD (5 << 6)
......@@ -542,12 +618,12 @@ static void net_tx_timeout (struct net_device *dev)
inw (ioaddr + STATUS), inb (ioaddr + TX_STATUS) & 0x80
? "IRQ conflict" : "network cable problem");
printk ("%s: timeout registers: %04x %04x %04x %04x %04x %04x %04x %04x.\n",
dev->name, inw (ioaddr + 0), inw (ioaddr + 2), inw (ioaddr + 4),
inw (ioaddr + 6), inw (ioaddr + 8), inw (ioaddr + 10),
inw (ioaddr + 12), inw (ioaddr + 14));
dev->name, inw(ioaddr + TX_STATUS), inw(ioaddr + TX_INTR), inw(ioaddr + TX_MODE),
inw(ioaddr + CONFIG_0), inw(ioaddr + DATAPORT), inw(ioaddr + TX_START),
inw(ioaddr + MODE13 - 1), inw(ioaddr + RX_CTRL));
lp->stats.tx_errors++;
/* ToDo: We should try to restart the adaptor... */
outw (0xffff, ioaddr + 24);
outw(0xffff, ioaddr + MODE24);
outw (0xffff, ioaddr + TX_STATUS);
outb (0x5a, ioaddr + CONFIG_0);
outb (0xe8, ioaddr + CONFIG_1);
......@@ -704,7 +780,7 @@ net_rx(struct net_device *dev)
dev->name, inb(ioaddr + RX_MODE), status);
#ifndef final_version
if (status == 0) {
outb(0x05, ioaddr + 14);
outb(0x05, ioaddr + RX_CTRL);
break;
}
#endif
......@@ -724,7 +800,7 @@ net_rx(struct net_device *dev)
dev->name, pkt_len);
/* Prime the FIFO and then flush the packet. */
inw(ioaddr + DATAPORT); inw(ioaddr + DATAPORT);
outb(0x05, ioaddr + 14);
outb(0x05, ioaddr + RX_CTRL);
lp->stats.rx_errors++;
break;
}
......@@ -734,7 +810,7 @@ net_rx(struct net_device *dev)
dev->name, pkt_len);
/* Prime the FIFO and then flush the packet. */
inw(ioaddr + DATAPORT); inw(ioaddr + DATAPORT);
outb(0x05, ioaddr + 14);
outb(0x05, ioaddr + RX_CTRL);
lp->stats.rx_dropped++;
break;
}
......@@ -761,7 +837,7 @@ net_rx(struct net_device *dev)
if ((inb(ioaddr + RX_MODE) & 0x40) == 0x40)
break;
inw(ioaddr + DATAPORT); /* dummy status read */
outb(0x05, ioaddr + 14);
outb(0x05, ioaddr + RX_CTRL);
}
if (net_debug > 5)
......@@ -844,24 +920,28 @@ set_rx_mode(struct net_device *dev)
outb(0x02, ioaddr + RX_MODE); /* Use normal mode. */
}
save_flags(flags);
cli();
spin_lock_irqsave (&lp->lock, flags);
if (memcmp(mc_filter, lp->mc_filter, sizeof(mc_filter))) {
int saved_bank = inw(ioaddr + CONFIG_0);
/* Switch to bank 1 and set the multicast table. */
outw((saved_bank & ~0x0C00) | 0x0480, ioaddr + CONFIG_0);
for (i = 0; i < 8; i++)
outb(mc_filter[i], ioaddr + 8 + i);
outb(mc_filter[i], ioaddr + PORT_OFFSET(8 + i));
memcpy(lp->mc_filter, mc_filter, sizeof(mc_filter));
outw(saved_bank, ioaddr + CONFIG_0);
}
restore_flags(flags);
spin_unlock_irqrestore (&lp->lock, flags);
return;
}
#ifdef MODULE
static struct net_device dev_at1700;
#ifndef CONFIG_X86_PC9800
static int io = 0x260;
#else
static int io = 0xd0;
#endif
static int irq;
MODULE_PARM(io, "i");
......@@ -901,7 +981,15 @@ cleanup_module(void)
/* If we don't do this, we can't re-insmod it later. */
free_irq(dev_at1700.irq, NULL);
#ifndef CONFIG_X86_PC9800
release_region(dev_at1700.base_addr, AT1700_IO_EXTENT);
#else
{
int i;
for (i = 0; i < 0x2000; i += 0x200)
release_region(dev_at1700.base_addr + i, 2);
}
#endif
}
#endif /* MODULE */
MODULE_LICENSE("GPL");
......
drivers/net/e100/e100.h
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -57,6 +57,8 @@
#include <linux/if.h>
#include <asm/uaccess.h>
#include <linux/ip.h>
#include <linux/if_vlan.h>
#include <linux/mii.h>
#define E100_REGS_LEN 1
/*
......@@ -301,6 +303,9 @@ struct driver_stats {
/* EEPROM bit definitions */
/*- EEPROM control register bits */
#define EEPROM_FLAG_ASF 0x8000
#define EEPROM_FLAG_GCL 0x4000
#define EN_TRNF 0x10 /* Enable turnoff */
#define EEDO 0x08 /* EEPROM data out */
#define EEDI 0x04 /* EEPROM data in (set for writing data) */
......@@ -319,6 +324,8 @@ struct driver_stats {
#define EEPROM_COMPATIBILITY_WORD 3
#define EEPROM_PWA_NO 8
#define EEPROM_ID_WORD 0x0A
#define EEPROM_CONFIG_ASF 0x0D
#define EEPROM_SMBUS_ADDR 0x90
#define EEPROM_SUM 0xbaba
......@@ -358,7 +365,7 @@ struct driver_stats {
#define CB_STATUS_MASK BIT_12_15 /* CB Status Mask (4-bits) */
#define CB_STATUS_COMPLETE BIT_15 /* CB Complete Bit */
#define CB_STATUS_OK BIT_13 /* CB OK Bit */
#define CB_STATUS_UNDERRUN BIT_12 /* CB A Bit */
#define CB_STATUS_VLAN BIT_12 /* CB Valn detected Bit */
#define CB_STATUS_FAIL BIT_11 /* CB Fail (F) Bit */
/*misc command bits */
......@@ -851,6 +858,7 @@ struct ethtool_lpbk_data{
};
struct e100_private {
struct vlan_group *vlgrp;
u32 flags; /* board management flags */
u32 tx_per_underrun; /* number of good tx frames per underrun */
unsigned int tx_count; /* count of tx frames, so we can request an interrupt */
......@@ -886,7 +894,6 @@ struct e100_private {
struct driver_stats drv_stats;
u8 rev_id; /* adapter PCI revision ID */
unsigned long device_type; /* device type from e100_vendor.h */
unsigned int phy_addr; /* address of PHY component */
unsigned int PhyId; /* ID of PHY component */
......@@ -923,8 +930,6 @@ struct e100_private {
struct cfg_params params; /* adapter's command line parameters */
char *id_string;
u32 speed_duplex_caps; /* adapter's speed/duplex capabilities */
/* WOL params for ethtool */
......
drivers/net/e100/e100_config.c
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -521,6 +521,25 @@ e100_config_wol(struct e100_private *bdp)
spin_unlock_bh(&(bdp->config_lock));
}
void
e100_config_vlan_drop(struct e100_private *bdp, unsigned char enable)
{
spin_lock_bh(&(bdp->config_lock));
if (enable) {
if (!(bdp->config[22] & CB_CFIG_VLAN_DROP_ENABLE)) {
bdp->config[22] |= CB_CFIG_VLAN_DROP_ENABLE;
E100_CONFIG(bdp, 22);
}
} else {
if ((bdp->config[22] & CB_CFIG_VLAN_DROP_ENABLE)) {
bdp->config[22] &= ~CB_CFIG_VLAN_DROP_ENABLE;
E100_CONFIG(bdp, 22);
}
}
spin_unlock_bh(&(bdp->config_lock));
}
/**
* e100_config_loopback_mode
* @bdp: atapter's private data struct
......
drivers/net/e100/e100_config.h
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -163,5 +163,5 @@ extern void e100_config_force_dplx(struct e100_private *bdp);
extern u8 e100_config_loopback_mode(struct e100_private *bdp, u8 mode);
extern u8 e100_config_dynamic_tbd(struct e100_private *bdp, u8 enable);
extern u8 e100_config_tcb_ext_enable(struct e100_private *bdp, u8 enable);
extern void e100_config_vlan_drop(struct e100_private *bdp, unsigned char enable);
#endif /* _E100_CONFIG_INC_ */
drivers/net/e100/e100_eeprom.c
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......
drivers/net/e100/e100_main.c
View file @ a20b40ff
This diff is collapsed.
drivers/net/e100/e100_phy.c
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -636,7 +636,6 @@ e100_force_speed_duplex(struct e100_private *bdp)
control &= ~BMCR_ANENABLE;
control &= ~BMCR_LOOPBACK;
/* Check e100.c values */
switch (bdp->params.e100_speed_duplex) {
case E100_SPEED_10_HALF:
control &= ~BMCR_SPEED100;
......@@ -682,6 +681,41 @@ e100_force_speed_duplex(struct e100_private *bdp)
} while (true);
}
void
e100_force_speed_duplex_to_phy(struct e100_private *bdp)
{
u16 control;
e100_mdi_read(bdp, MII_BMCR, bdp->phy_addr, &control);
control &= ~BMCR_ANENABLE;
control &= ~BMCR_LOOPBACK;
switch (bdp->params.e100_speed_duplex) {
case E100_SPEED_10_HALF:
control &= ~BMCR_SPEED100;
control &= ~BMCR_FULLDPLX;
break;
case E100_SPEED_10_FULL:
control &= ~BMCR_SPEED100;
control |= BMCR_FULLDPLX;
break;
case E100_SPEED_100_HALF:
control |= BMCR_SPEED100;
control &= ~BMCR_FULLDPLX;
break;
case E100_SPEED_100_FULL:
control |= BMCR_SPEED100;
control |= BMCR_FULLDPLX;
break;
}
/* Send speed/duplex command to PHY layer. */
e100_mdi_write(bdp, MII_BMCR, bdp->phy_addr, control);
}
/*
* Procedure: e100_set_fc
*
......
drivers/net/e100/e100_phy.h
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -30,8 +30,6 @@
#include "e100.h"
#include <linux/mii.h>
/*
* Auto-polarity enable/disable
* e100_autopolarity = 0 => disable auto-polarity
......
drivers/net/e100/e100_test.c
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -242,6 +242,9 @@ e100_diag_config_loopback(struct e100_private* bdp,
*dynamic_tbd = e100_config_dynamic_tbd(bdp,*dynamic_tbd);
if (set_loopback) {
/* ICH PHY loopback is broken */
if (bdp->flags & IS_ICH && loopback_mode == PHY_LOOPBACK)
loopback_mode = MAC_LOOPBACK;
/* Configure loopback on MAC */
e100_config_loopback_mode(bdp,loopback_mode);
} else {
......
drivers/net/e100/e100_ucode.h
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......
drivers/net/e100/e100_vendor.h deleted 100644 → 0
View file @ 5e1dcb06
This diff is collapsed.
drivers/net/e1000/e1000.h
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -65,6 +65,7 @@
#include <linux/reboot.h>
#include <net/checksum.h>
#include <linux/workqueue.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
#include <linux/if_vlan.h>
......@@ -95,6 +96,15 @@ struct e1000_adapter;
#define E1000_RXBUFFER_8192 8192
#define E1000_RXBUFFER_16384 16384
/* SmartSpeed delimiters */
#define E1000_SMARTSPEED_DOWNSHIFT 3
#define E1000_SMARTSPEED_MAX 15
/* Packet Buffer allocations */
#define E1000_TX_FIFO_SIZE_SHIFT 0xA
#define E1000_TX_HEAD_ADDR_SHIFT 7
#define E1000_PBA_TX_MASK 0xFFFF0000
/* Flow Control High-Watermark: 43464 bytes */
#define E1000_FC_HIGH_THRESH 0xA9C8
......@@ -107,10 +117,7 @@ struct e1000_adapter;
/* How many Tx Descriptors do we need to call netif_wake_queue ? */
#define E1000_TX_QUEUE_WAKE 16
/* How many Rx Buffers do we bundle into one write to the hardware ? */
#define E1000_RX_BUFFER_WRITE 16
#define E1000_JUMBO_PBA 0x00000028
#define E1000_DEFAULT_PBA 0x00000030
#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */
#define AUTO_ALL_MODES 0
#define E1000_EEPROM_APME 4
......@@ -145,7 +152,8 @@ struct e1000_desc_ring {
};
#define E1000_DESC_UNUSED(R) \
((((R)->next_to_clean + (R)->count) - ((R)->next_to_use + 1)) % ((R)->count))
((((R)->next_to_clean > (R)->next_to_use) ? 0 : (R)->count) + \
(R)->next_to_clean - (R)->next_to_use - 1)
#define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i]))
#define E1000_RX_DESC(R, i) E1000_GET_DESC(R, i, e1000_rx_desc)
......@@ -155,6 +163,7 @@ struct e1000_desc_ring {
/* board specific private data structure */
struct e1000_adapter {
struct timer_list tx_fifo_stall_timer;
struct timer_list watchdog_timer;
struct timer_list phy_info_timer;
struct vlan_group *vlgrp;
......@@ -163,6 +172,7 @@ struct e1000_adapter {
uint32_t rx_buffer_len;
uint32_t part_num;
uint32_t wol;
uint32_t smartspeed;
uint16_t link_speed;
uint16_t link_duplex;
spinlock_t stats_lock;
......@@ -177,7 +187,11 @@ struct e1000_adapter {
uint32_t txd_cmd;
uint32_t tx_int_delay;
uint32_t tx_abs_int_delay;
int max_data_per_txd;
uint32_t gotcl;
uint32_t tx_fifo_head;
uint32_t tx_head_addr;
uint32_t tx_fifo_size;
atomic_t tx_fifo_stall;
/* RX */
struct e1000_desc_ring rx_ring;
......@@ -186,6 +200,10 @@ struct e1000_adapter {
uint32_t rx_int_delay;
uint32_t rx_abs_int_delay;
boolean_t rx_csum;
uint32_t gorcl;
/* Interrupt Throttle Rate */
uint32_t itr;
/* OS defined structs */
struct net_device *netdev;
......
drivers/net/e1000/e1000_ethtool.c
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -38,6 +38,7 @@ extern char e1000_driver_version[];
extern int e1000_up(struct e1000_adapter *adapter);
extern void e1000_down(struct e1000_adapter *adapter);
extern void e1000_reset(struct e1000_adapter *adapter);
extern int e1000_set_spd_dplx(struct e1000_adapter *adapter, uint16_t spddplx);
static char e1000_gstrings_stats[][ETH_GSTRING_LEN] = {
"rx_packets", "tx_packets", "rx_bytes", "tx_bytes", "rx_errors",
......@@ -129,30 +130,9 @@ e1000_ethtool_sset(struct e1000_adapter *adapter, struct ethtool_cmd *ecmd)
hw->autoneg = 1;
hw->autoneg_advertised = 0x002F;
ecmd->advertising = 0x002F;
} else {
hw->autoneg = 0;
switch(ecmd->speed + ecmd->duplex) {
case SPEED_10 + DUPLEX_HALF:
hw->forced_speed_duplex = e1000_10_half;
break;
case SPEED_10 + DUPLEX_FULL:
hw->forced_speed_duplex = e1000_10_full;
break;
case SPEED_100 + DUPLEX_HALF:
hw->forced_speed_duplex = e1000_100_half;
break;
case SPEED_100 + DUPLEX_FULL:
hw->forced_speed_duplex = e1000_100_full;
break;
case SPEED_1000 + DUPLEX_FULL:
hw->autoneg = 1;
hw->autoneg_advertised = ADVERTISE_1000_FULL;
break;
case SPEED_1000 + DUPLEX_HALF: /* not supported */
default:
} else
if(e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex))
return -EINVAL;
}
}
/* reset the link */
......@@ -165,16 +145,6 @@ e1000_ethtool_sset(struct e1000_adapter *adapter, struct ethtool_cmd *ecmd)
return 0;
}
static inline int
e1000_eeprom_size(struct e1000_hw *hw)
{
if((hw->mac_type > e1000_82544) &&
(E1000_READ_REG(hw, EECD) & E1000_EECD_SIZE))
return 512;
else
return 128;
}
static void
e1000_ethtool_gdrvinfo(struct e1000_adapter *adapter,
struct ethtool_drvinfo *drvinfo)
......@@ -186,7 +156,7 @@ e1000_ethtool_gdrvinfo(struct e1000_adapter *adapter,
drvinfo->n_stats = E1000_STATS_LEN;
#define E1000_REGS_LEN 32
drvinfo->regdump_len = E1000_REGS_LEN * sizeof(uint32_t);
drvinfo->eedump_len = e1000_eeprom_size(&adapter->hw);
drvinfo->eedump_len = adapter->hw.eeprom.word_size * 2;
}
static void
......@@ -220,9 +190,8 @@ e1000_ethtool_geeprom(struct e1000_adapter *adapter,
struct ethtool_eeprom *eeprom, uint16_t *eeprom_buff)
{
struct e1000_hw *hw = &adapter->hw;
int max_len, first_word, last_word;
int first_word, last_word;
int ret_val = 0;
int i;
if(eeprom->len == 0) {
ret_val = -EINVAL;
......@@ -231,22 +200,28 @@ e1000_ethtool_geeprom(struct e1000_adapter *adapter,
eeprom->magic = hw->vendor_id | (hw->device_id << 16);
max_len = e1000_eeprom_size(hw);
if(eeprom->offset > eeprom->offset + eeprom->len) {
ret_val = -EINVAL;
goto geeprom_error;
}
if((eeprom->offset + eeprom->len) > max_len)
eeprom->len = (max_len - eeprom->offset);
if((eeprom->offset + eeprom->len) > (hw->eeprom.word_size * 2))
eeprom->len = ((hw->eeprom.word_size * 2) - eeprom->offset);
first_word = eeprom->offset >> 1;
last_word = (eeprom->offset + eeprom->len - 1) >> 1;
for(i = 0; i <= (last_word - first_word); i++)
e1000_read_eeprom(hw, first_word + i, &eeprom_buff[i]);
if(hw->eeprom.type == e1000_eeprom_spi)
ret_val = e1000_read_eeprom(hw, first_word,
last_word - first_word + 1,
eeprom_buff);
else {
uint16_t i;
for (i = 0; i < last_word - first_word + 1; i++)
if((ret_val = e1000_read_eeprom(hw, first_word + i, 1,
&eeprom_buff[i])))
break;
}
geeprom_error:
return ret_val;
}
......@@ -257,9 +232,8 @@ e1000_ethtool_seeprom(struct e1000_adapter *adapter,
{
struct e1000_hw *hw = &adapter->hw;
uint16_t *eeprom_buff;
int max_len, first_word, last_word;
void *ptr;
int i;
int max_len, first_word, last_word, ret_val = 0;
if(eeprom->len == 0)
return -EOPNOTSUPP;
......@@ -267,7 +241,7 @@ e1000_ethtool_seeprom(struct e1000_adapter *adapter,
if(eeprom->magic != (hw->vendor_id | (hw->device_id << 16)))
return -EFAULT;
max_len = e1000_eeprom_size(hw);
max_len = hw->eeprom.word_size * 2;
if((eeprom->offset + eeprom->len) > max_len)
eeprom->len = (max_len - eeprom->offset);
......@@ -283,30 +257,31 @@ e1000_ethtool_seeprom(struct e1000_adapter *adapter,
if(eeprom->offset & 1) {
/* need read/modify/write of first changed EEPROM word */
/* only the second byte of the word is being modified */
e1000_read_eeprom(hw, first_word, &eeprom_buff[0]);
ret_val = e1000_read_eeprom(hw, first_word, 1,
&eeprom_buff[0]);
ptr++;
}
if((eeprom->offset + eeprom->len) & 1) {
if(((eeprom->offset + eeprom->len) & 1) && (ret_val == 0)) {
/* need read/modify/write of last changed EEPROM word */
/* only the first byte of the word is being modified */
e1000_read_eeprom(hw, last_word,
ret_val = e1000_read_eeprom(hw, last_word, 1,
&eeprom_buff[last_word - first_word]);
}
if(copy_from_user(ptr, user_data, eeprom->len)) {
kfree(eeprom_buff);
return -EFAULT;
if((ret_val != 0) || copy_from_user(ptr, user_data, eeprom->len)) {
ret_val = -EFAULT;
goto seeprom_error;
}
for(i = 0; i <= (last_word - first_word); i++)
e1000_write_eeprom(hw, first_word + i, eeprom_buff[i]);
ret_val = e1000_write_eeprom(hw, first_word,
last_word - first_word + 1, eeprom_buff);
/* Update the checksum over the first part of the EEPROM if needed */
if(first_word <= EEPROM_CHECKSUM_REG)
if((ret_val == 0) && first_word <= EEPROM_CHECKSUM_REG)
e1000_update_eeprom_checksum(hw);
seeprom_error:
kfree(eeprom_buff);
return 0;
return ret_val;
}
static void
......@@ -333,8 +308,8 @@ e1000_ethtool_gwol(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
/* Fall Through */
default:
wol->supported = WAKE_UCAST | WAKE_MCAST
| WAKE_BCAST | WAKE_MAGIC;
wol->supported = WAKE_UCAST | WAKE_MCAST |
WAKE_BCAST | WAKE_MAGIC;
wol->wolopts = 0;
if(adapter->wol & E1000_WUFC_EX)
......@@ -368,7 +343,7 @@ e1000_ethtool_swol(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
/* Fall Through */
default:
if(wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE | WAKE_PHY))
if(wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE))
return -EOPNOTSUPP;
adapter->wol = 0;
......@@ -542,13 +517,12 @@ e1000_ethtool_ioctl(struct net_device *netdev, struct ifreq *ifr)
}
case ETHTOOL_GEEPROM: {
struct ethtool_eeprom eeprom = {ETHTOOL_GEEPROM};
struct e1000_hw *hw = &adapter->hw;
uint16_t *eeprom_buff;
void *ptr;
int max_len, err = 0;
max_len = e1000_eeprom_size(&adapter->hw);
int err = 0;
eeprom_buff = kmalloc(max_len, GFP_KERNEL);
eeprom_buff = kmalloc(hw->eeprom.word_size * 2, GFP_KERNEL);
if(eeprom_buff == NULL)
return -ENOMEM;
......
drivers/net/e1000/e1000_hw.c
View file @ a20b40ff
This diff is collapsed.
drivers/net/e1000/e1000_hw.h
View file @ a20b40ff
This diff is collapsed.
drivers/net/e1000/e1000_main.c
View file @ a20b40ff
This diff is collapsed.
drivers/net/e1000/e1000_osdep.h
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -77,24 +77,22 @@ typedef enum {
#define E1000_WRITE_REG(a, reg, value) ( \
((a)->mac_type >= e1000_82543) ? \
(writel((value), ((a)->hw_addr + E1000_##reg))) : \
(writel((value), ((a)->hw_addr + E1000_82542_##reg))))
writel((value), ((a)->hw_addr + \
(((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg))))
#define E1000_READ_REG(a, reg) ( \
((a)->mac_type >= e1000_82543) ? \
readl((a)->hw_addr + E1000_##reg) : \
readl((a)->hw_addr + E1000_82542_##reg))
readl((a)->hw_addr + \
(((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg)))
#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) ( \
((a)->mac_type >= e1000_82543) ? \
writel((value), ((a)->hw_addr + E1000_##reg + ((offset) << 2))) : \
writel((value), ((a)->hw_addr + E1000_82542_##reg + ((offset) << 2))))
writel((value), ((a)->hw_addr + \
(((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
((offset) << 2))))
#define E1000_READ_REG_ARRAY(a, reg, offset) ( \
((a)->mac_type >= e1000_82543) ? \
readl((a)->hw_addr + E1000_##reg + ((offset) << 2)) : \
readl((a)->hw_addr + E1000_82542_##reg + ((offset) << 2)))
readl((a)->hw_addr + \
(((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
((offset) << 2)))
#define E1000_WRITE_FLUSH(a) E1000_READ_REG(a, STATUS)
......
drivers/net/e1000/e1000_param.c
View file @ a20b40ff
/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
......@@ -169,7 +169,7 @@ E1000_PARAM(TxAbsIntDelay, "Transmit Absolute Interrupt Delay");
*
* Valid Range: 0-65535
*
* Default Value: 0/128
* Default Value: 0
*/
E1000_PARAM(RxIntDelay, "Receive Interrupt Delay");
......@@ -183,6 +183,15 @@ E1000_PARAM(RxIntDelay, "Receive Interrupt Delay");
E1000_PARAM(RxAbsIntDelay, "Receive Absolute Interrupt Delay");
/* Interrupt Throttle Rate (interrupts/sec)
*
* Valid Range: 100-100000 (0=off, 1=dynamic)
*
* Default Value: 1
*/
E1000_PARAM(InterruptThrottleRate, "Interrupt Throttling Rate");
#define AUTONEG_ADV_DEFAULT 0x2F
#define AUTONEG_ADV_MASK 0x2F
#define FLOW_CONTROL_DEFAULT FLOW_CONTROL_FULL
......@@ -213,6 +222,10 @@ E1000_PARAM(RxAbsIntDelay, "Receive Absolute Interrupt Delay");
#define MAX_TXABSDELAY 0xFFFF
#define MIN_TXABSDELAY 0
#define DEFAULT_ITR 1
#define MAX_ITR 100000
#define MIN_ITR 100
struct e1000_option {
enum { enable_option, range_option, list_option } type;
char *name;
......@@ -309,7 +322,7 @@ e1000_check_options(struct e1000_adapter *adapter)
.name = "Transmit Descriptors",
.err = "using default of " __MODULE_STRING(DEFAULT_TXD),
.def = DEFAULT_TXD,
.arg = { .r = { .min = MIN_TXD }}
.arg = { .r { .min = MIN_TXD }}
};
struct e1000_desc_ring *tx_ring = &adapter->tx_ring;
e1000_mac_type mac_type = adapter->hw.mac_type;
......@@ -362,7 +375,8 @@ e1000_check_options(struct e1000_adapter *adapter)
.name = "Flow Control",
.err = "reading default settings from EEPROM",
.def = e1000_fc_default,
.arg = { .l = { .nr = ARRAY_SIZE(fc_list), .p = fc_list }}
.arg = { .l = { .nr = ARRAY_SIZE(fc_list),
.p = fc_list }}
};
int fc = FlowControl[bd];
......@@ -370,58 +384,78 @@ e1000_check_options(struct e1000_adapter *adapter)
adapter->hw.fc = adapter->hw.original_fc = fc;
}
{ /* Transmit Interrupt Delay */
char *tidv = "using default of " __MODULE_STRING(DEFAULT_TIDV);
struct e1000_option opt = {
.type = range_option,
.name = "Transmit Interrupt Delay",
.arg = { .r = { .min = MIN_TXDELAY, .max = MAX_TXDELAY }}
.err = "using default of " __MODULE_STRING(DEFAULT_TIDV),
.def = DEFAULT_TIDV,
.arg = { .r = { .min = MIN_TXDELAY,
.max = MAX_TXDELAY }}
};
opt.def = DEFAULT_TIDV;
opt.err = tidv;
adapter->tx_int_delay = TxIntDelay[bd];
e1000_validate_option(&adapter->tx_int_delay, &opt);
}
{ /* Transmit Absolute Interrupt Delay */
char *tadv = "using default of " __MODULE_STRING(DEFAULT_TADV);
struct e1000_option opt = {
.type = range_option,
.name = "Transmit Absolute Interrupt Delay",
.arg = { .r = { .min = MIN_TXABSDELAY, .max = MAX_TXABSDELAY }}
.err = "using default of " __MODULE_STRING(DEFAULT_TADV),
.def = DEFAULT_TADV,
.arg = { .r = { .min = MIN_TXABSDELAY,
.max = MAX_TXABSDELAY }}
};
opt.def = DEFAULT_TADV;
opt.err = tadv;
adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
e1000_validate_option(&adapter->tx_abs_int_delay, &opt);
}
{ /* Receive Interrupt Delay */
char *rdtr = "using default of " __MODULE_STRING(DEFAULT_RDTR);
struct e1000_option opt = {
.type = range_option,
.name = "Receive Interrupt Delay",
.arg = { .r = { .min = MIN_RXDELAY, .max = MAX_RXDELAY }}
.err = "using default of " __MODULE_STRING(DEFAULT_RDTR),
.def = DEFAULT_RDTR,
.arg = { .r = { .min = MIN_RXDELAY,
.max = MAX_RXDELAY }}
};
opt.def = DEFAULT_RDTR;
opt.err = rdtr;
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt);
}
{ /* Receive Absolute Interrupt Delay */
char *radv = "using default of " __MODULE_STRING(DEFAULT_RADV);
struct e1000_option opt = {
.type = range_option,
.name = "Receive Absolute Interrupt Delay",
.arg = { .r = { .min = MIN_RXABSDELAY, .max = MAX_RXABSDELAY }}
.err = "using default of " __MODULE_STRING(DEFAULT_RADV),
.def = DEFAULT_RADV,
.arg = { .r = { .min = MIN_RXABSDELAY,
.max = MAX_RXABSDELAY }}
};
opt.def = DEFAULT_RADV;
opt.err = radv;
adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
e1000_validate_option(&adapter->rx_abs_int_delay, &opt);
}
{ /* Interrupt Throttling Rate */
struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Throttling Rate (ints/sec)",
.err = "using default of " __MODULE_STRING(DEFAULT_ITR),
.def = DEFAULT_ITR,
.arg = { .r = { .min = MIN_ITR,
.max = MAX_ITR }}
};
adapter->itr = InterruptThrottleRate[bd];
if(adapter->itr == 0) {
printk(KERN_INFO "%s turned off\n", opt.name);
} else if(adapter->itr == 1 || adapter->itr == -1) {
/* Dynamic mode */
adapter->itr = 1;
} else {
e1000_validate_option(&adapter->itr, &opt);
}
}
switch(adapter->hw.media_type) {
case e1000_media_type_fiber:
e1000_check_fiber_options(adapter);
......@@ -486,7 +520,8 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
.name = "Speed",
.err = "parameter ignored",
.def = 0,
.arg = { .l = { .nr = ARRAY_SIZE(speed_list), .p = speed_list }}
.arg = { .l = { .nr = ARRAY_SIZE(speed_list),
.p = speed_list }}
};
speed = Speed[bd];
......@@ -502,7 +537,8 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
.name = "Duplex",
.err = "parameter ignored",
.def = 0,
.arg = { .l = { .nr = ARRAY_SIZE(dplx_list), .p = dplx_list }}
.arg = { .l = { .nr = ARRAY_SIZE(dplx_list),
.p = dplx_list }}
};
dplx = Duplex[bd];
......@@ -554,7 +590,8 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
.name = "AutoNeg",
.err = "parameter ignored",
.def = AUTONEG_ADV_DEFAULT,
.arg = { .l = { .nr = ARRAY_SIZE(an_list), .p = an_list }}
.arg = { .l = { .nr = ARRAY_SIZE(an_list),
.p = an_list }}
};
int an = AutoNeg[bd];
......
drivers/net/ne2k_cbus.c 0 → 100644
View file @ a20b40ff
This diff is collapsed.
drivers/net/ne2k_cbus.h 0 → 100644
View file @ a20b40ff
This diff is collapsed.
drivers/net/tg3.c
View file @ a20b40ff
......@@ -55,8 +55,8 @@
#define DRV_MODULE_NAME "tg3"
#define PFX DRV_MODULE_NAME ": "
#define DRV_MODULE_VERSION "1.4c"
#define DRV_MODULE_RELDATE "Feb 18, 2003"
#define DRV_MODULE_VERSION "1.5"
#define DRV_MODULE_RELDATE "March 21, 2003"
#define TG3_DEF_MAC_MODE 0
#define TG3_DEF_RX_MODE 0
......@@ -6581,11 +6581,11 @@ static int __devinit tg3_test_dma(struct tg3 *tp)
tw32(TG3PCI_DMA_RW_CTRL, tp->dma_rwctrl);
ret = 0;
if (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5700 &&
GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5701)
return 0;
goto out;
ret = 0;
while (1) {
u32 *p, i;
......
drivers/video/Makefile
View file @ a20b40ff
......@@ -58,7 +58,7 @@ obj-$(CONFIG_FB_TX3912) += tx3912fb.o cfbfillrect.o cfbcopyarea.o cfbi
obj-$(CONFIG_FB_MATROX) += matrox/
obj-$(CONFIG_FB_RIVA) += riva/ cfbimgblt.o vgastate.o
obj-$(CONFIG_FB_SIS) += sis/
obj-$(CONFIG_FB_ATY) += aty/ cfbimgblt.o cfbfillrect.o cfbimgblt.o
obj-$(CONFIG_FB_ATY) += aty/ cfbimgblt.o cfbfillrect.o cfbcopyarea.o cfbimgblt.o
obj-$(CONFIG_FB_I810) += i810/ cfbfillrect.o cfbcopyarea.o \
cfbimgblt.o vgastate.o
......
include/asm-i386/processor.h
View file @ a20b40ff
......@@ -371,6 +371,10 @@ struct tss_struct {
* pads the TSS to be cacheline-aligned (size is 0x100)
*/
unsigned long __cacheline_filler[5];
/*
* .. and then another 0x100 bytes for emergency kernel stack
*/
unsigned long stack[64];
};
struct thread_struct {
......
include/asm-sparc64/irq.h
View file @ a20b40ff
......@@ -117,8 +117,6 @@ static __inline__ char *__irq_itoa(unsigned int irq)
extern void disable_irq(unsigned int);
#define disable_irq_nosync disable_irq
extern void enable_irq(unsigned int);
extern void sparc64_init_timers(void (*lvl10_irq)(int, void *, struct pt_regs *),
unsigned long *);
extern unsigned int build_irq(int pil, int inofixup, unsigned long iclr, unsigned long imap);
extern unsigned int sbus_build_irq(void *sbus, unsigned int ino);
extern unsigned int psycho_build_irq(void *psycho, int imap_off, int ino, int need_dma_sync);
......
include/asm-sparc64/spitfire.h
View file @ a20b40ff
......@@ -45,8 +45,6 @@ enum ultra_tlb_layout {
extern enum ultra_tlb_layout tlb_type;
#define SPARC64_USE_STICK (tlb_type != spitfire)
#define CHEETAH_HIGHEST_LOCKED_TLBENT (16 - 1)
#define L1DCACHE_SIZE 0x4000
......
include/asm-sparc64/thread_info.h
View file @ a20b40ff
......@@ -97,7 +97,7 @@ struct thread_info {
#define TI_PCR 0x00000490
#define TI_CEE_STUFF 0x00000498
#define TI_RESTART_BLOCK 0x000004a0
#define TI_FPREGS 0x000004c0
#define TI_FPREGS 0x00000500
/* We embed this in the uppermost byte of thread_info->flags */
#define FAULT_CODE_WRITE 0x01 /* Write access, implies D-TLB */
......
include/asm-sparc64/timer.h
View file @ a20b40ff
......@@ -50,6 +50,17 @@ struct sun5_timer {
*/
#define SUN5_HZ_TO_LIMIT(__hz) (1000000/(__hz))
struct sparc64_tick_ops {
void (*init_tick)(unsigned long);
unsigned long (*get_tick)(void);
unsigned long (*get_compare)(void);
unsigned long (*add_tick)(unsigned long, unsigned long);
unsigned long (*add_compare)(unsigned long);
unsigned long softint_mask;
};
extern struct sparc64_tick_ops *tick_ops;
#ifdef CONFIG_SMP
extern unsigned long timer_tick_offset;
extern void timer_tick_interrupt(struct pt_regs *);
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7