Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM 64-bit DT updates from Arnd Bergmann:
 "The 64-bit DT changes are surprisingly small this time, we only add
  two SoC platforms: the ZTE ZX296718 Set-top-box SoC and the SocioNext
  UniPhier LD11 TV SoC, each with their reference boards.

  There are three new machines added for existing SoC platforms:

   - The Marvell Armada 8040 development board is an impressive
     quad-core Cortex-A72 machine with three 10gbit ethernet interfaces

   - Qualcomms DragonBoard 820c single-board computer is their current
     high-end phone platform in the 96boards form factor

   - Rockchip: Tronsmart Orion r86 set-top-box is a popular mid-range
     Android box based on the 8-core rk3368 SoC"

* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (91 commits)
  arm64: dts: berlin4ct: Add L2 cache topology
  arm64: dts: berlin4ct: enable all wdt nodes unconditionally
  arm64: dts: berlin4ct: switch to Cortex-A53 specific pmu nodes
  arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
  arm64: dts: apm: Add DT node for APM X-Gene 2 CPU clocks
  arm64: dts: apm: Add X-Gene SoC hwmon to device tree
  arm64: dts: apm: Fix interrupt polarity for X-Gene PCIe legacy interrupts
  arm64: dts: apm: Add APM X-Gene v2 SoC PMU DTS entries
  arm64: dts: apm: Add APM X-Gene SoC PMU DTS entries
  arm64: dts: marvell: enable MSI for PCIe on Armada 7K/8K
  arm64: dts: ls2080a: Add 'dma-coherent' for ls2080a PCI nodes
  arm64: dts: rockchip: add Type-C phy for RK3399
  arm64: dts: rockchip: enable the gmac for rk3399 evb board
  arm64: dts: rockchip: add the gmac needed node for rk3399
  arm64: dts: rockchip: support the pmu node for rk3399
  arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
  arm64: dts: rockchip: add the tcpc for rk3399 power domain
  arm64: dts: rockchip: add efuse0 device node for rk3399
  arm64: dts: rockchip: configure PCIe support for rk3399-evb
  arm64: dts: rockchip: add the PCIe controller support for RK3399
  ...

Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt

@@ -175,38 +175,55 @@ Example:
 	};
 
 -----------------------------------------------------------------------
-Hisilicon HiP05 PCIe-SAS system controller
+Hisilicon HiP05/HiP06 PCIe-SAS sub system controller
 
 Required properties:
 - compatible : "hisilicon,pcie-sas-subctrl", "syscon";
 - reg : Register address and size
 
-The HiP05 PCIe-SAS system controller is shared by PCIe and SAS controllers in
-HiP05 Soc to implement some basic configurations.
+The PCIe-SAS sub system controller is shared by PCIe and SAS controllers in
+HiP05 or HiP06 Soc to implement some basic configurations.
 
 Example:
-	/* for HiP05 PCIe-SAS system */
-	pcie_sas: system_controller@0xb0000000 {
+	/* for HiP05 PCIe-SAS sub system */
+	pcie_sas: system_controller@b0000000 {
 		compatible = "hisilicon,pcie-sas-subctrl", "syscon";
 		reg = <0xb0000000 0x10000>;
 	};
 
-Hisilicon HiP05 PERISUB system controller
+Hisilicon HiP05/HiP06 PERI sub system controller
 
 Required properties:
-- compatible : "hisilicon,hip05-perisubc", "syscon";
+- compatible : "hisilicon,peri-subctrl", "syscon";
 - reg : Register address and size
 
-The HiP05 PERISUB system controller is shared by peripheral controllers in
-HiP05 Soc to implement some basic configurations. The peripheral
+The PERI sub system controller is shared by peripheral controllers in
+HiP05 or HiP06 Soc to implement some basic configurations. The peripheral
 controllers include mdio, ddr, iic, uart, timer and so on.
 
 Example:
-	/* for HiP05 perisub-ctrl-c system */
+	/* for HiP05 sub peri system */
 	peri_c_subctrl: syscon@80000000 {
-		compatible = "hisilicon,hip05-perisubc", "syscon";
+		compatible = "hisilicon,peri-subctrl", "syscon";
 		reg = <0x0 0x80000000 0x0 0x10000>;
 	};
+
+Hisilicon HiP05/HiP06 DSA sub system controller
+
+Required properties:
+- compatible : "hisilicon,dsa-subctrl", "syscon";
+- reg : Register address and size
+
+The DSA sub system controller is shared by peripheral controllers in
+HiP05 or HiP06 Soc to implement some basic configurations.
+
+Example:
+	/* for HiP05 dsa sub system */
+	pcie_sas: system_controller@a0000000 {
+		compatible = "hisilicon,dsa-subctrl", "syscon";
+		reg = <0xa0000000 0x10000>;
+	};
+
 -----------------------------------------------------------------------
 Hisilicon CPU controller
 

Documentation/devicetree/bindings/arm/rockchip.txt

@@ -121,3 +121,7 @@ Rockchip platforms device tree bindings
 - Rockchip RK3399 evb:
     Required root node properties:
       - compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
+
+- Tronsmart Orion R68 Meta
+    Required root node properties:
+      - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";

Documentation/devicetree/bindings/arm/zte.txt

@@ -13,3 +13,27 @@ Low power management required properties:
 
 Bus matrix required properties:
       - compatible = "zte,zx-bus-matrix"
+
+
+---------------------------------------
+-  ZX296718 SoC:
+    Required root node properties:
+      - compatible = "zte,zx296718"
+
+ZX296718 EVB board:
+      - "zte,zx296718-evb"
+
+System management required properties:
+      - compatible = "zte,zx296718-aon-sysctrl"
+      - compatible = "zte,zx296718-sysctrl"
+
+Example:
+aon_sysctrl: aon-sysctrl@116000 {
+	compatible = "zte,zx296718-aon-sysctrl", "syscon";
+	reg = <0x116000 0x1000>;
+};
+
+sysctrl: sysctrl@1463000 {
+	compatible = "zte,zx296718-sysctrl", "syscon";
+	reg = <0x1463000 0x1000>;
+};

arch/arm64/Kconfig.platforms

@@ -172,6 +172,8 @@ config ARCH_TEGRA
 	select GENERIC_CLOCKEVENTS
 	select GPIOLIB
 	select PINCTRL
+	select PM
+	select PM_GENERIC_DOMAINS
 	select RESET_CONTROLLER
 	help
 	  This enables support for the NVIDIA Tegra SoC family.

arch/arm64/boot/dts/Makefile

@@ -19,6 +19,7 @@ dts-dirs += socionext
 dts-dirs += sprd
 dts-dirs += xilinx
 dts-dirs += lg
+dts-dirs += zte
 
 subdir-y	:= $(dts-dirs)
 

arch/arm64/boot/dts/apm/apm-shadowcat.dtsi

@@ -26,6 +26,8 @@ cpu@000 {
 			enable-method = "spin-table";
 			cpu-release-addr = <0x1 0x0000fff8>;
 			next-level-cache = <&xgene_L2_0>;
+			#clock-cells = <1>;
+			clocks = <&pmd0clk 0>;
 		};
 		cpu@001 {
 			device_type = "cpu";
@@ -34,6 +36,8 @@ cpu@001 {
 			enable-method = "spin-table";
 			cpu-release-addr = <0x1 0x0000fff8>;
 			next-level-cache = <&xgene_L2_0>;
+			#clock-cells = <1>;
+			clocks = <&pmd0clk 0>;
 		};
 		cpu@100 {
 			device_type = "cpu";
@@ -42,6 +46,8 @@ cpu@100 {
 			enable-method = "spin-table";
 			cpu-release-addr = <0x1 0x0000fff8>;
 			next-level-cache = <&xgene_L2_1>;
+			#clock-cells = <1>;
+			clocks = <&pmd1clk 0>;
 		};
 		cpu@101 {
 			device_type = "cpu";
@@ -50,6 +56,8 @@ cpu@101 {
 			enable-method = "spin-table";
 			cpu-release-addr = <0x1 0x0000fff8>;
 			next-level-cache = <&xgene_L2_1>;
+			#clock-cells = <1>;
+			clocks = <&pmd1clk 0>;
 		};
 		cpu@200 {
 			device_type = "cpu";
@@ -58,6 +66,8 @@ cpu@200 {
 			enable-method = "spin-table";
 			cpu-release-addr = <0x1 0x0000fff8>;
 			next-level-cache = <&xgene_L2_2>;
+			#clock-cells = <1>;
+			clocks = <&pmd2clk 0>;
 		};
 		cpu@201 {
 			device_type = "cpu";
@@ -66,6 +76,8 @@ cpu@201 {
 			enable-method = "spin-table";
 			cpu-release-addr = <0x1 0x0000fff8>;
 			next-level-cache = <&xgene_L2_2>;
+			#clock-cells = <1>;
+			clocks = <&pmd2clk 0>;
 		};
 		cpu@300 {
 			device_type = "cpu";
@@ -74,6 +86,8 @@ cpu@300 {
 			enable-method = "spin-table";
 			cpu-release-addr = <0x1 0x0000fff8>;
 			next-level-cache = <&xgene_L2_3>;
+			#clock-cells = <1>;
+			clocks = <&pmd3clk 0>;
 		};
 		cpu@301 {
 			device_type = "cpu";
@@ -82,6 +96,8 @@ cpu@301 {
 			enable-method = "spin-table";
 			cpu-release-addr = <0x1 0x0000fff8>;
 			next-level-cache = <&xgene_L2_3>;
+			#clock-cells = <1>;
+			clocks = <&pmd3clk 0>;
 		};
 		xgene_L2_0: l2-cache-0 {
 			compatible = "cache";
@@ -223,6 +239,46 @@ refclk: refclk {
 				clock-output-names = "refclk";
 			};
 
+			pmdpll: pmdpll@170000f0 {
+				compatible = "apm,xgene-pcppll-v2-clock";
+				#clock-cells = <1>;
+				clocks = <&refclk 0>;
+				reg = <0x0 0x170000f0 0x0 0x10>;
+				clock-output-names = "pmdpll";
+			};
+
+			pmd0clk: pmd0clk@7e200200 {
+				compatible = "apm,xgene-pmd-clock";
+				#clock-cells = <1>;
+				clocks = <&pmdpll 0>;
+				reg = <0x0 0x7e200200 0x0 0x10>;
+				clock-output-names = "pmd0clk";
+			};
+
+			pmd1clk: pmd1clk@7e200210 {
+				compatible = "apm,xgene-pmd-clock";
+				#clock-cells = <1>;
+				clocks = <&pmdpll 0>;
+				reg = <0x0 0x7e200210 0x0 0x10>;
+				clock-output-names = "pmd1clk";
+			};
+
+			pmd2clk: pmd2clk@7e200220 {
+				compatible = "apm,xgene-pmd-clock";
+				#clock-cells = <1>;
+				clocks = <&pmdpll 0>;
+				reg = <0x0 0x7e200220 0x0 0x10>;
+				clock-output-names = "pmd2clk";
+			};
+
+			pmd3clk: pmd3clk@7e200230 {
+				compatible = "apm,xgene-pmd-clock";
+				#clock-cells = <1>;
+				clocks = <&pmdpll 0>;
+				reg = <0x0 0x7e200230 0x0 0x10>;
+				clock-output-names = "pmd3clk";
+			};
+
 			socpll: socpll@17000120 {
 				compatible = "apm,xgene-socpll-v2-clock";
 				#clock-cells = <1>;
@@ -453,6 +509,64 @@ edacsoc@7e930000 {
 			};
 		};
 
+		pmu: pmu@78810000 {
+			compatible = "apm,xgene-pmu-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			regmap-csw = <&csw>;
+			regmap-mcba = <&mcba>;
+			regmap-mcbb = <&mcbb>;
+			reg = <0x0 0x78810000 0x0 0x1000>;
+			interrupts = <0x0 0x22 0x4>;
+
+			pmul3c@7e610000 {
+				compatible = "apm,xgene-pmu-l3c";
+				reg = <0x0 0x7e610000 0x0 0x1000>;
+			};
+
+			pmuiob@7e940000 {
+				compatible = "apm,xgene-pmu-iob";
+				reg = <0x0 0x7e940000 0x0 0x1000>;
+			};
+
+			pmucmcb@7e710000 {
+				compatible = "apm,xgene-pmu-mcb";
+				reg = <0x0 0x7e710000 0x0 0x1000>;
+				enable-bit-index = <0>;
+			};
+
+			pmucmcb@7e730000 {
+				compatible = "apm,xgene-pmu-mcb";
+				reg = <0x0 0x7e730000 0x0 0x1000>;
+				enable-bit-index = <1>;
+			};
+
+			pmucmc@7e810000 {
+				compatible = "apm,xgene-pmu-mc";
+				reg = <0x0 0x7e810000 0x0 0x1000>;
+				enable-bit-index = <0>;
+			};
+
+			pmucmc@7e850000 {
+				compatible = "apm,xgene-pmu-mc";
+				reg = <0x0 0x7e850000 0x0 0x1000>;
+				enable-bit-index = <1>;
+			};
+
+			pmucmc@7e890000 {
+				compatible = "apm,xgene-pmu-mc";
+				reg = <0x0 0x7e890000 0x0 0x1000>;
+				enable-bit-index = <2>;
+			};
+
+			pmucmc@7e8d0000 {
+				compatible = "apm,xgene-pmu-mc";
+				reg = <0x0 0x7e8d0000 0x0 0x1000>;
+				enable-bit-index = <3>;
+			};
+		};
+
 		mailbox: mailbox@10540000 {
 			compatible = "apm,xgene-slimpro-mbox";
 			reg = <0x0 0x10540000 0x0 0x8000>;
@@ -472,6 +586,11 @@ i2cslimpro {
 			mboxes = <&mailbox 0>;
 		};
 
+		hwmonslimpro {
+			compatible = "apm,xgene-slimpro-hwmon";
+			mboxes = <&mailbox 7>;
+		};
+
 		serial0: serial@10600000 {
 			device_type = "serial";
 			compatible = "ns16550";
@@ -508,10 +627,10 @@ pcie0: pcie@1f2b0000 {
 			dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
 				      0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
 			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x10 0x1
-					 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x11 0x1
-					 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x12 0x1
-					 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x13 0x1>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x10 0x4
+					 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x11 0x4
+					 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x12 0x4
+					 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x13 0x4>;
 			dma-coherent;
 			clocks = <&pcie0clk 0>;
 			msi-parent = <&v2m0>;
@@ -533,10 +652,10 @@ pcie1: pcie@1f2c0000 {
 			dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
 				      0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
 			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x16 0x1
-					 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x17 0x1
-					 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x18 0x1
-					 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x19 0x1>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x16 0x4
+					 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x17 0x4
+					 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x18 0x4
+					 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x19 0x4>;
 			dma-coherent;
 			clocks = <&pcie1clk 0>;
 			msi-parent = <&v2m0>;

arch/arm64/boot/dts/apm/apm-storm.dtsi

@@ -553,6 +553,64 @@ edacsoc@7e930000 {
 			};
 		};
 
+		pmu: pmu@78810000 {
+			compatible = "apm,xgene-pmu-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			regmap-csw = <&csw>;
+			regmap-mcba = <&mcba>;
+			regmap-mcbb = <&mcbb>;
+			reg = <0x0 0x78810000 0x0 0x1000>;
+			interrupts = <0x0 0x22 0x4>;
+
+			pmul3c@7e610000 {
+				compatible = "apm,xgene-pmu-l3c";
+				reg = <0x0 0x7e610000 0x0 0x1000>;
+			};
+
+			pmuiob@7e940000 {
+				compatible = "apm,xgene-pmu-iob";
+				reg = <0x0 0x7e940000 0x0 0x1000>;
+			};
+
+			pmucmcb@7e710000 {
+				compatible = "apm,xgene-pmu-mcb";
+				reg = <0x0 0x7e710000 0x0 0x1000>;
+				enable-bit-index = <0>;
+			};
+
+			pmucmcb@7e730000 {
+				compatible = "apm,xgene-pmu-mcb";
+				reg = <0x0 0x7e730000 0x0 0x1000>;
+				enable-bit-index = <1>;
+			};
+
+			pmucmc@7e810000 {
+				compatible = "apm,xgene-pmu-mc";
+				reg = <0x0 0x7e810000 0x0 0x1000>;
+				enable-bit-index = <0>;
+			};
+
+			pmucmc@7e850000 {
+				compatible = "apm,xgene-pmu-mc";
+				reg = <0x0 0x7e850000 0x0 0x1000>;
+				enable-bit-index = <1>;
+			};
+
+			pmucmc@7e890000 {
+				compatible = "apm,xgene-pmu-mc";
+				reg = <0x0 0x7e890000 0x0 0x1000>;
+				enable-bit-index = <2>;
+			};
+
+			pmucmc@7e8d0000 {
+				compatible = "apm,xgene-pmu-mc";
+				reg = <0x0 0x7e8d0000 0x0 0x1000>;
+				enable-bit-index = <3>;
+			};
+		};
+
 		pcie0: pcie@1f2b0000 {
 			status = "disabled";
 			device_type = "pci";
@@ -569,10 +627,10 @@ pcie0: pcie@1f2b0000 {
 			dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
 				      0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
 			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1
-					 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1
-					 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1
-					 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x4
+					 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x4
+					 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x4
+					 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x4>;
 			dma-coherent;
 			clocks = <&pcie0clk 0>;
 			msi-parent = <&msi>;
@@ -594,10 +652,10 @@ pcie1: pcie@1f2c0000 {
 			dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
 				      0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
 			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc8 0x1
-					 0x0 0x0 0x0 0x2 &gic 0x0 0xc9 0x1
-					 0x0 0x0 0x0 0x3 &gic 0x0 0xca 0x1
-					 0x0 0x0 0x0 0x4 &gic 0x0 0xcb 0x1>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc8 0x4
+					 0x0 0x0 0x0 0x2 &gic 0x0 0xc9 0x4
+					 0x0 0x0 0x0 0x3 &gic 0x0 0xca 0x4
+					 0x0 0x0 0x0 0x4 &gic 0x0 0xcb 0x4>;
 			dma-coherent;
 			clocks = <&pcie1clk 0>;
 			msi-parent = <&msi>;
@@ -619,10 +677,10 @@ pcie2: pcie@1f2d0000 {
 			dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
 				      0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
 			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xce 0x1
-					 0x0 0x0 0x0 0x2 &gic 0x0 0xcf 0x1
-					 0x0 0x0 0x0 0x3 &gic 0x0 0xd0 0x1
-					 0x0 0x0 0x0 0x4 &gic 0x0 0xd1 0x1>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xce 0x4
+					 0x0 0x0 0x0 0x2 &gic 0x0 0xcf 0x4
+					 0x0 0x0 0x0 0x3 &gic 0x0 0xd0 0x4
+					 0x0 0x0 0x0 0x4 &gic 0x0 0xd1 0x4>;
 			dma-coherent;
 			clocks = <&pcie2clk 0>;
 			msi-parent = <&msi>;
@@ -644,10 +702,10 @@ pcie3: pcie@1f500000 {
 			dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
 				      0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
 			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xd4 0x1
-					 0x0 0x0 0x0 0x2 &gic 0x0 0xd5 0x1
-					 0x0 0x0 0x0 0x3 &gic 0x0 0xd6 0x1
-					 0x0 0x0 0x0 0x4 &gic 0x0 0xd7 0x1>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xd4 0x4
+					 0x0 0x0 0x0 0x2 &gic 0x0 0xd5 0x4
+					 0x0 0x0 0x0 0x3 &gic 0x0 0xd6 0x4
+					 0x0 0x0 0x0 0x4 &gic 0x0 0xd7 0x4>;
 			dma-coherent;
 			clocks = <&pcie3clk 0>;
 			msi-parent = <&msi>;
@@ -669,10 +727,10 @@ pcie4: pcie@1f510000 {
 			dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
 				      0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
 			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xda 0x1
-					 0x0 0x0 0x0 0x2 &gic 0x0 0xdb 0x1
-					 0x0 0x0 0x0 0x3 &gic 0x0 0xdc 0x1
-					 0x0 0x0 0x0 0x4 &gic 0x0 0xdd 0x1>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xda 0x4
+					 0x0 0x0 0x0 0x2 &gic 0x0 0xdb 0x4
+					 0x0 0x0 0x0 0x3 &gic 0x0 0xdc 0x4
+					 0x0 0x0 0x0 0x4 &gic 0x0 0xdd 0x4>;
 			dma-coherent;
 			clocks = <&pcie4clk 0>;
 			msi-parent = <&msi>;
@@ -697,6 +755,11 @@ i2cslimpro {
 			mboxes = <&mailbox 0>;
 		};
 
+		hwmonslimpro {
+			compatible = "apm,xgene-slimpro-hwmon";
+			mboxes = <&mailbox 7>;
+		};
+
 		serial0: serial@1c020000 {
 			status = "disabled";
 			device_type = "serial";

arch/arm64/boot/dts/broadcom/ns2.dtsi

@@ -299,6 +299,14 @@ pmu@9000 {
 			};
 		};
 
+		pwm: pwm@66010000 {
+			compatible = "brcm,iproc-pwm";
+			reg = <0x66010000 0x28>;
+			clocks = <&osc>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		mdio_mux_iproc: mdio-mux@6602023c {
 			compatible = "brcm,mdio-mux-iproc";
 			reg = <0x6602023c 0x14>;

arch/arm64/boot/dts/exynos/exynos7.dtsi

@@ -10,6 +10,7 @@
  */
 
 #include <dt-bindings/clock/exynos7-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	compatible = "samsung,exynos7";
@@ -473,10 +474,14 @@ hsi2c_11: hsi2c@136a0000 {
 
 		timer {
 			compatible = "arm,armv8-timer";
-			interrupts = <1 13 0xff08>,
-				     <1 14 0xff08>,
-				     <1 11 0xff08>,
-				     <1 10 0xff08>;
+			interrupts = <GIC_PPI 13
+					(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 14
+					(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 11
+					(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 10
+					(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
 		};
 
 		pmu_system_controller: system-controller@105c0000 {

arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts

@@ -56,12 +56,14 @@ aliases {
 		gpio1 = &gpio2;
 		gpio2 = &gpio3;
 		gpio3 = &gpio4;
-		serial0 = &lpuart0;
-		serial1 = &lpuart1;
-		serial2 = &lpuart2;
-		serial3 = &lpuart3;
-		serial4 = &lpuart4;
-		serial5 = &lpuart5;
+		serial0 = &duart0;
+		serial1 = &duart1;
+		serial2 = &duart2;
+		serial3 = &duart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
 	};
 };
 

arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts

@@ -52,6 +52,14 @@ / {
 
 	aliases {
 		crypto = &crypto;
+		serial0 = &duart0;
+		serial1 = &duart1;
+		serial2 = &duart2;
+		serial3 = &duart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
 	};
 };
 

arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi

@@ -247,6 +247,13 @@ esdhc: esdhc@1560000 {
 			bus-width = <4>;
 		};
 
+		ddr: memory-controller@1080000 {
+			compatible = "fsl,qoriq-memory-controller";
+			reg = <0x0 0x1080000 0x0 0x1000>;
+			interrupts = <0 144 0x4>;
+			big-endian;
+		};
+
 		dspi0: dspi@2100000 {
 			compatible = "fsl,ls1043a-dspi", "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts

@@ -57,6 +57,9 @@ aliases {
 		serial1 = &serial1;
 	};
 
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
 };
 
 &esdhc {

arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts

@@ -56,6 +56,10 @@ aliases {
 		serial0 = &serial0;
 		serial1 = &serial1;
 	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
 };
 
 &esdhc {

arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi

@@ -588,6 +588,7 @@ pcie@3400000 {
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
+			dma-coherent;
 			num-lanes = <4>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x10 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -612,6 +613,7 @@ pcie@3500000 {
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
+			dma-coherent;
 			num-lanes = <4>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x12 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -636,6 +638,7 @@ pcie@3600000 {
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
+			dma-coherent;
 			num-lanes = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x14 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -660,6 +663,7 @@ pcie@3700000 {
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
+			dma-coherent;
 			num-lanes = <4>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -715,4 +719,18 @@ ccn@4000000 {
 			interrupts = <0 12 4>;
 		};
 	};
+
+	ddr1: memory-controller@1080000 {
+		compatible = "fsl,qoriq-memory-controller";
+		reg = <0x0 0x1080000 0x0 0x1000>;
+		interrupts = <0 17 0x4>;
+		little-endian;
+	};
+
+	ddr2: memory-controller@1090000 {
+		compatible = "fsl,qoriq-memory-controller";
+		reg = <0x0 0x1090000 0x0 0x1000>;
+		interrupts = <0 18 0x4>;
+		little-endian;
+	};
 };

arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts

@@ -29,16 +29,56 @@ chosen {
 	 * Reserve below regions from memory node:
 	 *
 	 *  0x05e0,0000 - 0x05ef,ffff: MCU firmware runtime using
+	 *  0x05f0,1000 - 0x05f0,1fff: Reboot reason
 	 *  0x06df,f000 - 0x06df,ffff: Mailbox message data
 	 *  0x0740,f000 - 0x0740,ffff: MCU firmware section
+	 *  0x21f0,0000 - 0x21ff,ffff: pstore/ramoops buffer
 	 *  0x3e00,0000 - 0x3fff,ffff: OP-TEE
 	 */
 	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x00000000 0x00000000 0x05e00000>,
-		      <0x00000000 0x05f00000 0x00000000 0x00eff000>,
+		      <0x00000000 0x05f00000 0x00000000 0x00001000>,
+		      <0x00000000 0x05f02000 0x00000000 0x00efd000>,
 		      <0x00000000 0x06e00000 0x00000000 0x0060f000>,
-		      <0x00000000 0x07410000 0x00000000 0x36bf0000>;
+		      <0x00000000 0x07410000 0x00000000 0x1aaf0000>,
+		      <0x00000000 0x22000000 0x00000000 0x1c000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@0x21f00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x21f00000 0x0 0x00100000>;
+			record-size	= <0x00020000>;
+			console-size	= <0x00020000>;
+			ftrace-size	= <0x00020000>;
+		};
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x00000000 0x08000000>;
+			linux,cma-default;
+		};
+	};
+
+	reboot-mode-syscon@5f01000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x05f01000 0x0 0x00001000>;
+
+		reboot-mode {
+			compatible = "syscon-reboot-mode";
+			offset = <0x0>;
+
+			mode-normal	= <0x77665501>;
+			mode-bootloader	= <0x77665500>;
+			mode-recovery	= <0x77665502>;
+		};
 	};
 
 	soc {
@@ -55,6 +95,8 @@ i2c1: i2c@f7101000 {
 		};
 
 		uart1: uart@f7111000 {
+			assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
+			assigned-clock-rates = <150000000>;
 			status = "ok";
 		};
 
@@ -372,3 +414,43 @@ &uart2 {
 &uart3 {
 	label = "LS-UART1";
 };
+
+&ade {
+	status = "ok";
+};
+
+&dsi {
+	status = "ok";
+
+	ports {
+		/* 1 for output port */
+		port@1 {
+			reg = <1>;
+
+			dsi_out0: endpoint@0 {
+				remote-endpoint = <&adv7533_in>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "ok";
+
+	adv7533: adv7533@39 {
+		compatible = "adi,adv7533";
+		reg = <0x39>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 2>;
+		pd-gpio = <&gpio0 4 0>;
+		adi,dsi-lanes = <4>;
+
+		port {
+			adv7533_in: endpoint {
+				remote-endpoint = <&dsi_out0>;
+			};
+		};
+	};
+};

arch/arm64/boot/dts/hisilicon/hi6220.dtsi

@@ -262,6 +262,11 @@ pm_ctrl: pm_ctrl@f7032000 {
 			#clock-cells = <1>;
 		};
 
+		medianoc_ade: medianoc_ade@f4520000 {
+			compatible = "syscon";
+			reg = <0x0 0xf4520000 0x0 0x4000>;
+		};
+
 		stub_clock: stub_clock {
 			compatible = "hisilicon,hi6220-stub-clk";
 			hisilicon,hi6220-clk-sram = <&sram>;
@@ -766,6 +771,7 @@ dwmmc_0: dwmmc0@f723d000 {
 			interrupts = <0x0 0x48 0x4>;
 			clocks = <&sys_ctrl 2>, <&sys_ctrl 1>;
 			clock-names = "ciu", "biu";
+			resets = <&sys_ctrl PERIPH_RSTDIS0_MMC0>;
 			bus-width = <0x8>;
 			vmmc-supply = <&ldo19>;
 			pinctrl-names = "default";
@@ -779,12 +785,16 @@ dwmmc_1: dwmmc1@f723e000 {
 			card-detect-delay = <200>;
 			hisilicon,peripheral-syscon = <&ao_ctrl>;
 			cap-sd-highspeed;
+			sd-uhs-sdr12;
+			sd-uhs-sdr25;
+			sd-uhs-sdr50;
 			reg = <0x0 0xf723e000 0x0 0x1000>;
 			interrupts = <0x0 0x49 0x4>;
 			#address-cells = <0x1>;
 			#size-cells = <0x0>;
 			clocks = <&sys_ctrl 4>, <&sys_ctrl 3>;
 			clock-names = "ciu", "biu";
+			resets = <&sys_ctrl PERIPH_RSTDIS0_MMC1>;
 			vqmmc-supply = <&ldo7>;
 			vmmc-supply = <&ldo10>;
 			bus-width = <0x4>;
@@ -802,6 +812,7 @@ dwmmc_2: dwmmc2@f723f000 {
 			interrupts = <0x0 0x4a 0x4>;
 			clocks = <&sys_ctrl HI6220_MMC2_CIUCLK>, <&sys_ctrl HI6220_MMC2_CLK>;
 			clock-names = "ciu", "biu";
+			resets = <&sys_ctrl PERIPH_RSTDIS0_MMC2>;
 			bus-width = <0x4>;
 			broken-cd;
 			pinctrl-names = "default", "idle";
@@ -850,5 +861,55 @@ map0 {
 				};
 			};
 		};
+
+		ade: ade@f4100000 {
+			compatible = "hisilicon,hi6220-ade";
+			reg = <0x0 0xf4100000 0x0 0x7800>;
+			reg-names = "ade_base";
+			hisilicon,noc-syscon = <&medianoc_ade>;
+			resets = <&media_ctrl MEDIA_ADE>;
+			interrupts = <0 115 4>; /* ldi interrupt */
+
+			clocks = <&media_ctrl HI6220_ADE_CORE>,
+				 <&media_ctrl HI6220_CODEC_JPEG>,
+				 <&media_ctrl HI6220_ADE_PIX_SRC>;
+			/*clock name*/
+			clock-names  = "clk_ade_core",
+				       "clk_codec_jpeg",
+				       "clk_ade_pix";
+
+			assigned-clocks = <&media_ctrl HI6220_ADE_CORE>,
+				<&media_ctrl HI6220_CODEC_JPEG>;
+			assigned-clock-rates = <360000000>, <288000000>;
+			dma-coherent;
+			status = "disabled";
+
+			port {
+				ade_out: endpoint {
+					remote-endpoint = <&dsi_in>;
+				};
+			};
+		};
+
+		dsi: dsi@f4107800 {
+			compatible = "hisilicon,hi6220-dsi";
+			reg = <0x0 0xf4107800 0x0 0x100>;
+			clocks = <&media_ctrl  HI6220_DSI_PCLK>;
+			clock-names = "pclk";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* 0 for input port */
+				port@0 {
+					reg = <0>;
+					dsi_in: endpoint {
+						remote-endpoint = <&ade_out>;
+					};
+				};
+			};
+		};
 	};
 };

arch/arm64/boot/dts/hisilicon/hip05.dtsi

@@ -300,11 +300,6 @@ refclk200mhz: refclk200mhz {
 			clock-frequency = <200000000>;
 		};
 
-		peri_c_subctrl: syscon@80000000 {
-			compatible = "hisilicon,hip05-perisubc", "syscon";
-			reg = < 0x0 0x80000000 0x0 0x10000>;
-		};
-
 		uart0: uart@80300000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x0 0x80300000 0x0 0x10000>;

arch/arm64/boot/dts/hisilicon/hip05_hns.dtsi

-soc0: soc@000000000 {
-	#address-cells = <2>;
-	#size-cells = <2>;
-	device_type = "soc";
-	compatible = "simple-bus";
-	ranges = <0x0 0x0 0x0 0x0 0x1 0x0>;
-	chip-id = <0>;
-
-	soc0_mdio0: mdio@803c0000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "hisilicon,hns-mdio";
-		reg = <0x0 0x803c0000 0x0 0x10000>;
-		subctrl-vbase = <&peri_c_subctrl>;
-
-		soc0_phy0: ethernet-phy@0 {
-			reg = <0x0>;
-			compatible = "ethernet-phy-ieee802.3-c22";
-		};
-		soc0_phy1: ethernet-phy@1 {
-			reg = <0x1>;
-			compatible = "ethernet-phy-ieee802.3-c22";
-		};
-	};
-
-	dsaf0: dsa@c7000000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "hisilicon,hns-dsaf-v1";
-		mode = "6port-16rss";
-		interrupt-parent = <&mbigen_dsa>;
-
-		reg = <0x0 0xc5000000 0x0 0x890000
-		       0x0 0xc7000000 0x0 0x60000
-		       >;
-
-		reg-names = "ppe-base","dsaf-base";
-		subctrl-syscon = <&dsaf_subctrl>;
-		reset-field-offset = <0>;
-		interrupts = <
-			/* [14] ge fifo err 8 / xge 6**/
-			149 0x4 150 0x4 151 0x4 152 0x4
-			153 0x4 154 0x4  26 0x4 27 0x4
-			155 0x4 156 0x4 157 0x4 158 0x4 159 0x4 160 0x4
-			/* [12] rcb com 4*3**/
-			0x6 0x4 0x7 0x4 0x8 0x4 0x9 0x4
-			 16 0x4  17 0x4  18 0x4  19 0x4
-			 22 0x4  23 0x4  24 0x4  25 0x4
-			/* [8] ppe tnl 0-7***/
-			0x0 0x4 0x1 0x4 0x2 0x4 0x3 0x4
-			0x4 0x4 0x5 0x4 12 0x4 13 0x4
-			/* [21] dsaf event int 3+18**/
-			 128 0x4  129 0x4  130 0x4
-			0x83 0x4 0x84 0x4 0x85 0x4 0x86 0x4 0x87 0x4 0x88 0x4
-			0x89 0x4 0x8a 0x4 0x8b 0x4 0x8c 0x4 0x8d 0x4 0x8e 0x4
-			0x8f 0x4 0x90 0x4 0x91 0x4 0x92 0x4 0x93 0x4 0x94 0x4
-			/* [4] debug rcb 2*2*/
-			0xe 0x1 0xf 0x1 0x14 0x1 0x15 0x1
-			/* [256] sevice rcb 2*128*/
-			0x180 0x1 0x181 0x1 0x182 0x1 0x183 0x1
-			0x184 0x1 0x185 0x1 0x186 0x1 0x187 0x1
-			0x188 0x1 0x189 0x1 0x18a 0x1 0x18b 0x1
-			0x18c 0x1 0x18d 0x1 0x18e 0x1 0x18f 0x1
-			0x190 0x1 0x191 0x1 0x192 0x1 0x193 0x1
-			0x194 0x1 0x195 0x1 0x196 0x1 0x197 0x1
-			0x198 0x1 0x199 0x1 0x19a 0x1 0x19b 0x1
-			0x19c 0x1 0x19d 0x1 0x19e 0x1 0x19f 0x1
-			0x1a0 0x1 0x1a1 0x1 0x1a2 0x1 0x1a3 0x1
-			0x1a4 0x1 0x1a5 0x1 0x1a6 0x1 0x1a7 0x1
-			0x1a8 0x1 0x1a9 0x1 0x1aa 0x1 0x1ab 0x1
-			0x1ac 0x1 0x1ad 0x1 0x1ae 0x1 0x1af 0x1
-			0x1b0 0x1 0x1b1 0x1 0x1b2 0x1 0x1b3 0x1
-			0x1b4 0x1 0x1b5 0x1 0x1b6 0x1 0x1b7 0x1
-			0x1b8 0x1 0x1b9 0x1 0x1ba 0x1 0x1bb 0x1
-			0x1bc 0x1 0x1bd 0x1 0x1be 0x1 0x1bf 0x1
-			0x1c0 0x1 0x1c1 0x1 0x1c2 0x1 0x1c3 0x1
-			0x1c4 0x1 0x1c5 0x1 0x1c6 0x1 0x1c7 0x1
-			0x1c8 0x1 0x1c9 0x1 0x1ca 0x1 0x1cb 0x1
-			0x1cc 0x1 0x1cd 0x1 0x1ce 0x1 0x1cf 0x1
-			0x1d0 0x1 0x1d1 0x1 0x1d2 0x1 0x1d3 0x1
-			0x1d4 0x1 0x1d5 0x1 0x1d6 0x1 0x1d7 0x1
-			0x1d8 0x1 0x1d9 0x1 0x1da 0x1 0x1db 0x1
-			0x1dc 0x1 0x1dd 0x1 0x1de 0x1 0x1df 0x1
-			0x1e0 0x1 0x1e1 0x1 0x1e2 0x1 0x1e3 0x1
-			0x1e4 0x1 0x1e5 0x1 0x1e6 0x1 0x1e7 0x1
-			0x1e8 0x1 0x1e9 0x1 0x1ea 0x1 0x1eb 0x1
-			0x1ec 0x1 0x1ed 0x1 0x1ee 0x1 0x1ef 0x1
-			0x1f0 0x1 0x1f1 0x1 0x1f2 0x1 0x1f3 0x1
-			0x1f4 0x1 0x1f5 0x1 0x1f6 0x1 0x1f7 0x1
-			0x1f8 0x1 0x1f9 0x1 0x1fa 0x1 0x1fb 0x1
-			0x1fc 0x1 0x1fd 0x1 0x1fe 0x1 0x1ff 0x1
-			0x200 0x1 0x201 0x1 0x202 0x1 0x203 0x1
-			0x204 0x1 0x205 0x1 0x206 0x1 0x207 0x1
-			0x208 0x1 0x209 0x1 0x20a 0x1 0x20b 0x1
-			0x20c 0x1 0x20d 0x1 0x20e 0x1 0x20f 0x1
-			0x210 0x1 0x211 0x1 0x212 0x1 0x213 0x1
-			0x214 0x1 0x215 0x1 0x216 0x1 0x217 0x1
-			0x218 0x1 0x219 0x1 0x21a 0x1 0x21b 0x1
-			0x21c 0x1 0x21d 0x1 0x21e 0x1 0x21f 0x1
-			0x220 0x1 0x221 0x1 0x222 0x1 0x223 0x1
-			0x224 0x1 0x225 0x1 0x226 0x1 0x227 0x1
-			0x228 0x1 0x229 0x1 0x22a 0x1 0x22b 0x1
-			0x22c 0x1 0x22d 0x1 0x22e 0x1 0x22f 0x1
-			0x230 0x1 0x231 0x1 0x232 0x1 0x233 0x1
-			0x234 0x1 0x235 0x1 0x236 0x1 0x237 0x1
-			0x238 0x1 0x239 0x1 0x23a 0x1 0x23b 0x1
-			0x23c 0x1 0x23d 0x1 0x23e 0x1 0x23f 0x1
-			0x240 0x1 0x241 0x1 0x242 0x1 0x243 0x1
-			0x244 0x1 0x245 0x1 0x246 0x1 0x247 0x1
-			0x248 0x1 0x249 0x1 0x24a 0x1 0x24b 0x1
-			0x24c 0x1 0x24d 0x1 0x24e 0x1 0x24f 0x1
-			0x250 0x1 0x251 0x1 0x252 0x1 0x253 0x1
-			0x254 0x1 0x255 0x1 0x256 0x1 0x257 0x1
-			0x258 0x1 0x259 0x1 0x25a 0x1 0x25b 0x1
-			0x25c 0x1 0x25d 0x1 0x25e 0x1 0x25f 0x1
-			0x260 0x1 0x261 0x1 0x262 0x1 0x263 0x1
-			0x264 0x1 0x265 0x1 0x266 0x1 0x267 0x1
-			0x268 0x1 0x269 0x1 0x26a 0x1 0x26b 0x1
-			0x26c 0x1 0x26d 0x1 0x26e 0x1 0x26f 0x1
-			0x270 0x1 0x271 0x1 0x272 0x1 0x273 0x1
-			0x274 0x1 0x275 0x1 0x276 0x1 0x277 0x1
-			0x278 0x1 0x279 0x1 0x27a 0x1 0x27b 0x1
-			0x27c 0x1 0x27d 0x1 0x27e 0x1 0x27f 0x1>;
-		buf-size = <4096>;
-		desc-num = <1024>;
-		dma-coherent;
-
-		port@0 {
-			reg = <0>;
-			serdes-syscon = <&serdes_ctrl0>;
-		};
-		port@1 {
-			reg = <1>;
-			serdes-syscon = <&serdes_ctrl0>;
-		};
-		port@4 {
-			reg = <4>;
-			phy-handle = <&soc0_phy0>;
-			serdes-syscon = <&serdes_ctrl1>;
-		};
-		port@5 {
-			reg = <5>;
-			phy-handle = <&soc0_phy1>;
-			serdes-syscon = <&serdes_ctrl1>;
-		};
-	};
-
-	eth0: ethernet@0{
-		compatible = "hisilicon,hns-nic-v1";
-		ae-handle = <&dsaf0>;
-		port-idx-in-ae = <0>;
-		local-mac-address = [00 00 00 01 00 58];
-		status = "disabled";
-		dma-coherent;
-	};
-	eth1: ethernet@1{
-		compatible = "hisilicon,hns-nic-v1";
-		ae-handle = <&dsaf0>;
-		port-idx-in-ae = <1>;
-		local-mac-address = [00 00 00 01 00 59];
-		status = "disabled";
-		dma-coherent;
-	};
-	eth2: ethernet@4{
-		compatible = "hisilicon,hns-nic-v1";
-		ae-handle = <&dsaf0>;
-		port-idx-in-ae = <4>;
-		local-mac-address = [00 00 00 01 00 5a];
-		status = "disabled";
-		dma-coherent;
-	};
-	eth3: ethernet@5{
-		compatible = "hisilicon,hns-nic-v1";
-		ae-handle = <&dsaf0>;
-		port-idx-in-ae = <5>;
-		local-mac-address = [00 00 00 01 00 5b];
-		status = "disabled";
-		dma-coherent;
-	};
-};

arch/arm64/boot/dts/hisilicon/hip06-d03.dts

@@ -25,6 +25,34 @@ memory@00000000 {
 	chosen { };
 };
 
+&eth0 {
+	status = "ok";
+};
+
+&eth1 {
+	status = "ok";
+};
+
+&eth2 {
+	status = "ok";
+};
+
+&eth3 {
+	status = "ok";
+};
+
+&sas0 {
+	status = "ok";
+};
+
+&sas1 {
+	status = "ok";
+};
+
+&sas2 {
+	status = "ok";
+};
+
 &usb_ohci {
 	status = "ok";
 };

arch/arm64/boot/dts/marvell/Makefile

@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-stb.dtb
 # Mvebu SoC Family
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
 
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)

arch/arm64/boot/dts/marvell/armada-8020.dtsi

@@ -47,6 +47,7 @@
 
 #include "armada-ap806-dual.dtsi"
 #include "armada-cp110-master.dtsi"
+#include "armada-cp110-slave.dtsi"
 
 / {
 	model = "Marvell Armada 8020";

arch/arm64/boot/dts/marvell/armada-8040-db.dts

+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * Device Tree file for Marvell Armada 8040 Development board platform
+ */
+
+#include "armada-8040.dtsi"
+
+/ {
+	model = "Marvell Armada 8040 DB board";
+	compatible = "marvell,armada8040-db", "marvell,armada8040",
+		     "marvell,armada-ap806-quad", "marvell,armada-ap806";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@00000000 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&spi0 {
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0 0x200000>;
+			};
+			partition@400000 {
+				label = "Filesystem";
+				reg = <0x200000 0xce0000>;
+			};
+		};
+	};
+};
+
+/* Accessible over the mini-USB CON9 connector on the main board */
+&uart0 {
+	status = "okay";
+};
+
+
+/* CON5 on CP0 expansion */
+&cpm_pcie2 {
+	status = "okay";
+};
+
+&cpm_i2c0 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+/* CON4 on CP0 expansion */
+&cpm_sata0 {
+	status = "okay";
+};
+
+/* CON9 on CP0 expansion */
+&cpm_usb3_0 {
+	status = "okay";
+};
+
+/* CON10 on CP0 expansion */
+&cpm_usb3_1 {
+	status = "okay";
+};
+
+/* CON5 on CP1 expansion */
+&cps_pcie2 {
+	status = "okay";
+};
+
+&cps_i2c0 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+/* CON4 on CP1 expansion */
+&cps_sata0 {
+	status = "okay";
+};
+
+/* CON9 on CP1 expansion */
+&cps_usb3_0 {
+	status = "okay";
+};
+
+/* CON10 on CP1 expansion */
+&cps_usb3_1 {
+	status = "okay";
+};

arch/arm64/boot/dts/marvell/armada-8040.dtsi

@@ -47,6 +47,7 @@
 
 #include "armada-ap806-quad.dtsi"
 #include "armada-cp110-master.dtsi"
+#include "armada-cp110-slave.dtsi"
 
 / {
 	model = "Marvell Armada 8040";

arch/arm64/boot/dts/marvell/armada-ap806.dtsi

@@ -128,6 +128,12 @@ timer {
 					     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 			};
 
+			pmu {
+				compatible = "arm,cortex-a72-pmu";
+				interrupt-parent = <&pic>;
+				interrupts = <17>;
+			};
+
 			odmi: odmi@300000 {
 				compatible = "marvell,odmi-controller";
 				interrupt-controller;
@@ -140,6 +146,14 @@ odmi: odmi@300000 {
 				marvell,spi-base = <128>, <136>, <144>, <152>;
 			};
 
+			pic: interrupt-controller@3f0100 {
+				compatible = "marvell,armada-8k-pic";
+				reg = <0x3f0100 0x10>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
 			xor@400000 {
 				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
 				reg = <0x400000 0x1000>,

arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi

@@ -176,6 +176,7 @@ cpm_pcie0: pcie@f2600000 {
 			#interrupt-cells = <1>;
 			device_type = "pci";
 			dma-coherent;
+			msi-parent = <&gic_v2m0>;
 
 			bus-range = <0 0xff>;
 			ranges =
@@ -201,6 +202,7 @@ cpm_pcie1: pcie@f2620000 {
 			#interrupt-cells = <1>;
 			device_type = "pci";
 			dma-coherent;
+			msi-parent = <&gic_v2m0>;
 
 			bus-range = <0 0xff>;
 			ranges =
@@ -227,6 +229,7 @@ cpm_pcie2: pcie@f2640000 {
 			#interrupt-cells = <1>;
 			device_type = "pci";
 			dma-coherent;
+			msi-parent = <&gic_v2m0>;
 
 			bus-range = <0 0xff>;
 			ranges =

arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi

+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * Device Tree file for Marvell Armada CP110 Slave.
+ */
+
+/ {
+	cp110-slave {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		config-space {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			interrupt-parent = <&gic>;
+			ranges = <0x0 0x0 0xf4000000 0x2000000>;
+
+			cps_syscon0: system-controller@440000 {
+				compatible = "marvell,cp110-system-controller0",
+					     "syscon";
+				reg = <0x440000 0x1000>;
+				#clock-cells = <2>;
+				core-clock-output-names =
+					"cps-apll", "cps-ppv2-core", "cps-eip",
+					"cps-core", "cps-nand-core";
+				gate-clock-output-names =
+					"cps-audio", "cps-communit", "cps-nand",
+					"cps-ppv2", "cps-sdio", "cps-mg-domain",
+					"cps-mg-core", "cps-xor1", "cps-xor0",
+					"cps-gop-dp", "none", "cps-pcie_x10",
+					"cps-pcie_x11", "cps-pcie_x4", "cps-pcie-xor",
+					"cps-sata", "cps-sata-usb", "cps-main",
+					"cps-sd-mmc", "none", "none",
+					"cps-slow-io", "cps-usb3h0", "cps-usb3h1",
+					"cps-usb3dev", "cps-eip150", "cps-eip197";
+			};
+
+			cps_sata0: sata@540000 {
+				compatible = "marvell,armada-8k-ahci";
+				reg = <0x540000 0x30000>;
+				interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cps_syscon0 1 15>;
+				status = "disabled";
+			};
+
+			cps_usb3_0: usb3@500000 {
+				compatible = "marvell,armada-8k-xhci",
+					     "generic-xhci";
+				reg = <0x500000 0x4000>;
+				dma-coherent;
+				interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cps_syscon0 1 22>;
+				status = "disabled";
+			};
+
+			cps_usb3_1: usb3@510000 {
+				compatible = "marvell,armada-8k-xhci",
+					     "generic-xhci";
+				reg = <0x510000 0x4000>;
+				dma-coherent;
+				interrupts = <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cps_syscon0 1 23>;
+				status = "disabled";
+			};
+
+			cps_xor0: xor@6a0000 {
+				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+				reg = <0x6a0000 0x1000>,
+				      <0x6b0000 0x1000>;
+				dma-coherent;
+				msi-parent = <&gic_v2m0>;
+				clocks = <&cps_syscon0 1 8>;
+			};
+
+			cps_xor1: xor@6c0000 {
+				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+				reg = <0x6c0000 0x1000>,
+				      <0x6d0000 0x1000>;
+				dma-coherent;
+				msi-parent = <&gic_v2m0>;
+				clocks = <&cps_syscon0 1 7>;
+			};
+
+			cps_spi0: spi@700600 {
+				compatible = "marvell,armada-380-spi";
+				reg = <0x700600 0x50>;
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				cell-index = <1>;
+				clocks = <&cps_syscon0 0 3>;
+				status = "disabled";
+			};
+
+			cps_spi1: spi@700680 {
+				compatible = "marvell,armada-380-spi";
+				reg = <0x700680 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <2>;
+				clocks = <&cps_syscon0 1 21>;
+				status = "disabled";
+			};
+
+			cps_i2c0: i2c@701000 {
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x701000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cps_syscon0 1 21>;
+				status = "disabled";
+			};
+
+			cps_i2c1: i2c@701100 {
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x701100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cps_syscon0 1 21>;
+				status = "disabled";
+			};
+		};
+
+		cps_pcie0: pcie@f4600000 {
+			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+			reg = <0 0xf4600000 0 0x10000>,
+			      <0 0xfaf00000 0 0x80000>;
+			reg-names = "ctrl", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			device_type = "pci";
+			dma-coherent;
+			msi-parent = <&gic_v2m0>;
+
+			bus-range = <0 0xff>;
+			ranges =
+				/* downstream I/O */
+				<0x81000000 0 0xfd000000 0  0xfd000000 0 0x10000
+				/* non-prefetchable memory */
+				0x82000000 0 0xfa000000 0  0xfa000000 0 0xf00000>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
+			num-lanes = <1>;
+			clocks = <&cps_syscon0 1 13>;
+			status = "disabled";
+		};
+
+		cps_pcie1: pcie@f4620000 {
+			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+			reg = <0 0xf4620000 0 0x10000>,
+			      <0 0xfbf00000 0 0x80000>;
+			reg-names = "ctrl", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			device_type = "pci";
+			dma-coherent;
+			msi-parent = <&gic_v2m0>;
+
+			bus-range = <0 0xff>;
+			ranges =
+				/* downstream I/O */
+				<0x81000000 0 0xfd010000 0  0xfd010000 0 0x10000
+				/* non-prefetchable memory */
+				0x82000000 0 0xfb000000 0  0xfb000000 0 0xf00000>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>;
+
+			num-lanes = <1>;
+			clocks = <&cps_syscon0 1 11>;
+			status = "disabled";
+		};
+
+		cps_pcie2: pcie@f4640000 {
+			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+			reg = <0 0xf4640000 0 0x10000>,
+			      <0 0xfcf00000 0 0x80000>;
+			reg-names = "ctrl", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			device_type = "pci";
+			dma-coherent;
+			msi-parent = <&gic_v2m0>;
+
+			bus-range = <0 0xff>;
+			ranges =
+				/* downstream I/O */
+				<0x81000000 0 0xfd020000 0  0xfd020000 0 0x10000
+				/* non-prefetchable memory */
+				0x82000000 0 0xfc000000 0  0xfc000000 0 0xf00000>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>;
+
+			num-lanes = <1>;
+			clocks = <&cps_syscon0 1 12>;
+			status = "disabled";
+		};
+	};
+};

arch/arm64/boot/dts/marvell/berlin4ct.dtsi

@@ -68,6 +68,7 @@ cpu0: cpu@0 {
 			device_type = "cpu";
 			reg = <0x0>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			cpu-idle-states = <&CPU_SLEEP_0>;
 		};
 
@@ -76,6 +77,7 @@ cpu1: cpu@1 {
 			device_type = "cpu";
 			reg = <0x1>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			cpu-idle-states = <&CPU_SLEEP_0>;
 		};
 
@@ -84,6 +86,7 @@ cpu2: cpu@2 {
 			device_type = "cpu";
 			reg = <0x2>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			cpu-idle-states = <&CPU_SLEEP_0>;
 		};
 
@@ -92,9 +95,14 @@ cpu3: cpu@3 {
 			device_type = "cpu";
 			reg = <0x3>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			cpu-idle-states = <&CPU_SLEEP_0>;
 		};
 
+		l2: cache {
+			compatible = "cache";
+		};
+
 		idle-states {
 			entry-method = "psci";
 			CPU_SLEEP_0: cpu-sleep-0 {
@@ -115,7 +123,7 @@ osc: osc {
 	};
 
 	pmu {
-		compatible = "arm,armv8-pmuv3";
+		compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
@@ -279,7 +287,6 @@ wdt1: watchdog@4000 {
 				reg = <0x4000 0x100>;
 				clocks = <&osc>;
 				interrupts = <1>;
-				status = "disabled";
 			};
 
 			wdt2: watchdog@5000 {
@@ -287,7 +294,6 @@ wdt2: watchdog@5000 {
 				reg = <0x5000 0x100>;
 				clocks = <&osc>;
 				interrupts = <2>;
-				status = "disabled";
 			};
 
 			sm_gpio0: gpio@8000 {

arch/arm64/boot/dts/mediatek/mt8173-evb.dts

@@ -42,6 +42,44 @@ usb_p1_vbus: regulator@0 {
 		gpio = <&pio 130 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "d";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi0_out>;
+			};
+		};
+	};
+};
+
+&cec {
+	status = "okay";
+};
+
+&dpi0 {
+	status = "okay";
+};
+
+&hdmi_phy {
+	status = "okay";
+};
+
+&hdmi0 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			hdmi0_out: endpoint {
+				remote-endpoint = <&hdmi_connector_in>;
+			};
+		};
+	};
 };
 
 &i2c1 {

arch/arm64/boot/dts/mediatek/mt8173.dtsi

@@ -254,6 +254,16 @@ pio: pinctrl@0x10005000 {
 				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
 
+			hdmi_pin: xxx {
+
+				/*hdmi htplg pin*/
+				pins1 {
+					pinmux = <MT8173_PIN_21_HTPLG__FUNC_HTPLG>;
+					input-enable;
+					bias-pull-down;
+				};
+			};
+
 			i2c0_pins_a: i2c0 {
 				pins1 {
 					pinmux = <MT8173_PIN_45_SDA0__FUNC_SDA0>,
@@ -341,6 +351,14 @@ pwrap: pwrap@1000d000 {
 			clock-names = "spi", "wrap";
 		};
 
+		cec: cec@10013000 {
+			compatible = "mediatek,mt8173-cec";
+			reg = <0 0x10013000 0 0xbc>;
+			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&infracfg CLK_INFRA_CEC>;
+			status = "disabled";
+		};
+
 		vpu: vpu@10020000 {
 			compatible = "mediatek,mt8173-vpu";
 			reg = <0 0x10020000 0 0x30000>,
@@ -383,6 +401,19 @@ apmixedsys: clock-controller@10209000 {
 			#clock-cells = <1>;
 		};
 
+		hdmi_phy: hdmi-phy@10209100 {
+			compatible = "mediatek,mt8173-hdmi-phy";
+			reg = <0 0x10209100 0 0x24>;
+			clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
+			clock-names = "pll_ref";
+			clock-output-names = "hdmitx_dig_cts";
+			mediatek,ibias = <0xa>;
+			mediatek,ibias_up = <0x1c>;
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		mipi_tx0: mipi-dphy@10215000 {
 			compatible = "mediatek,mt8173-mipi-tx";
 			reg = <0 0x10215000 0 0x1000>;
@@ -577,6 +608,14 @@ i2c4: i2c@11011000 {
 			status = "disabled";
 		};
 
+		hdmiddc0: i2c@11012000 {
+			compatible = "mediatek,mt8173-hdmi-ddc";
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
+			reg = <0 0x11012000 0 0x1C>;
+			clocks = <&pericfg CLK_PERI_I2C5>;
+			clock-names = "ddc-i2c";
+		};
+
 		i2c6: i2c@11013000 {
 			compatible = "mediatek,mt8173-i2c";
 			reg = <0 0x11013000 0 0x70>,
@@ -885,6 +924,12 @@ dpi0: dpi@1401d000 {
 				 <&apmixedsys CLK_APMIXED_TVDPLL>;
 			clock-names = "pixel", "engine", "pll";
 			status = "disabled";
+
+			port {
+				dpi0_out: endpoint {
+					remote-endpoint = <&hdmi0_in>;
+				};
+			};
 		};
 
 		pwm0: pwm@1401e000 {
@@ -942,6 +987,38 @@ od@14023000 {
 			clocks = <&mmsys CLK_MM_DISP_OD>;
 		};
 
+		hdmi0: hdmi@14025000 {
+			compatible = "mediatek,mt8173-hdmi";
+			reg = <0 0x14025000 0 0x400>;
+			interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
+				 <&mmsys CLK_MM_HDMI_PLLCK>,
+				 <&mmsys CLK_MM_HDMI_AUDIO>,
+				 <&mmsys CLK_MM_HDMI_SPDIF>;
+			clock-names = "pixel", "pll", "bclk", "spdif";
+			pinctrl-names = "default";
+			pinctrl-0 = <&hdmi_pin>;
+			phys = <&hdmi_phy>;
+			phy-names = "hdmi";
+			mediatek,syscon-hdmi = <&mmsys 0x900>;
+			assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
+			assigned-clock-parents = <&hdmi_phy>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					hdmi0_in: endpoint {
+						remote-endpoint = <&dpi0_out>;
+					};
+				};
+			};
+		};
+
 		larb4: larb@14027000 {
 			compatible = "mediatek,mt8173-smi-larb";
 			reg = <0 0x14027000 0 0x1000>;

arch/arm64/boot/dts/nvidia/tegra210-smaug.dts

@@ -27,6 +27,12 @@ memory {
 		reg = <0x0 0x80000000 0x0 0xc0000000>;
 	};
 
+	host1x@50000000 {
+		dpaux: dpaux@545c0000 {
+			status = "okay";
+		};
+	};
+
 	pinmux: pinmux@700008d4 {
 		pinctrl-names = "boot";
 		pinctrl-0 = <&state_boot>;
@@ -1556,6 +1562,46 @@ avddio_1v05: ldo8 {
 		};
 	};
 
+	i2c@7000d100 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		nau8825@1a {
+			compatible = "nuvoton,nau8825";
+			reg = <0x1a>;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>;
+			clock-names = "mclk";
+
+			nuvoton,jkdet-enable;
+			nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
+			nuvoton,vref-impedance = <2>;
+			nuvoton,micbias-voltage = <6>;
+			nuvoton,sar-threshold-num = <4>;
+			nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
+			nuvoton,sar-hysteresis = <1>;
+			nuvoton,sar-voltage = <0>;
+			nuvoton,sar-compare-time = <0>;
+			nuvoton,sar-sampling-time = <0>;
+			nuvoton,short-key-debounce = <2>;
+			nuvoton,jack-insert-debounce = <7>;
+			nuvoton,jack-eject-debounce = <7>;
+			status = "okay";
+		};
+
+		audio-codec@2d {
+			compatible = "realtek,rt5677";
+			reg = <0x2d>;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 0) IRQ_TYPE_LEVEL_HIGH>;
+			realtek,reset-gpio = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_LOW>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "okay";
+		};
+	};
+
 	pmc@7000e400 {
 		nvidia,invert-interrupt;
 		nvidia,suspend-mode = <0>;
@@ -1568,12 +1614,81 @@ pmc@7000e400 {
 		status = "okay";
 	};
 
+	usb@70090000 {
+		phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>,
+		       <&{/padctl@7009f000/pads/pcie/lanes/pcie-6}>;
+		phy-names = "usb2-0", "usb3-0";
+
+		dvddio-pex-supply = <&avddio_1v05>;
+		hvddio-pex-supply = <&pp1800>;
+		avdd-usb-supply = <&pp3300>;
+		avdd-pll-utmip-supply = <&pp1800>;
+		avdd-pll-uerefe-supply = <&pp1050_avdd>;
+		dvdd-pex-pll-supply = <&avddio_1v05>;
+		hvdd-pex-pll-e-supply = <&pp1800>;
+
+		status = "okay";
+	};
+
+	padctl@7009f000 {
+		status = "okay";
+
+		pads {
+			usb2 {
+				status = "okay";
+
+				lanes {
+					usb2-0 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+				};
+			};
+
+			pcie {
+				status = "okay";
+
+				lanes {
+					pcie-6 {
+						nvidia,function = "usb3-ss";
+						status = "okay";
+					};
+				};
+			};
+		};
+
+		ports {
+			usb2-0 {
+				status = "okay";
+				vbus-supply = <&usbc_vbus>;
+				mode = "otg";
+			};
+
+			usb3-0 {
+				nvidia,usb2-companion = <0>;
+				status = "okay";
+			};
+		};
+	};
+
 	sdhci@700b0600 {
 		bus-width = <8>;
 		non-removable;
 		status = "okay";
 	};
 
+	aconnect@702c0000 {
+		status = "okay";
+
+		dma@702e2000 {
+			status = "okay";
+		};
+
+		agic@702f9000 {
+			status = "okay";
+		};
+	};
+
 	clocks {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -1646,6 +1761,11 @@ volume_up {
 		};
 	};
 
+	max98357a {
+		compatible = "maxim,max98357a";
+		status = "okay";
+	};
+
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";

arch/arm64/boot/dts/nvidia/tegra210.dtsi

@@ -34,6 +34,7 @@ dpaux1: dpaux@54040000 {
 			clock-names = "dpaux", "parent";
 			resets = <&tegra_car 207>;
 			reset-names = "dpaux";
+			power-domains = <&pd_sor>;
 			status = "disabled";
 
 			state_dpaux1_aux: pinmux-aux {
@@ -108,6 +109,7 @@ dsi@54300000 {
 			clock-names = "dsi", "lp", "parent";
 			resets = <&tegra_car 48>;
 			reset-names = "dsi";
+			power-domains = <&pd_sor>;
 			nvidia,mipi-calibrate = <&mipi 0x0c0>; /* DSIA & DSIB pads */
 
 			status = "disabled";
@@ -137,6 +139,7 @@ dsi@54400000 {
 			clock-names = "dsi", "lp", "parent";
 			resets = <&tegra_car 82>;
 			reset-names = "dsi";
+			power-domains = <&pd_sor>;
 			nvidia,mipi-calibrate = <&mipi 0x300>; /* DSIC & DSID pads */
 
 			status = "disabled";
@@ -178,6 +181,7 @@ sor@54540000 {
 			pinctrl-1 = <&state_dpaux_i2c>;
 			pinctrl-2 = <&state_dpaux_off>;
 			pinctrl-names = "aux", "i2c", "off";
+			power-domains = <&pd_sor>;
 			status = "disabled";
 		};
 
@@ -197,6 +201,7 @@ sor@54580000 {
 			pinctrl-1 = <&state_dpaux1_i2c>;
 			pinctrl-2 = <&state_dpaux1_off>;
 			pinctrl-names = "aux", "i2c", "off";
+			power-domains = <&pd_sor>;
 			status = "disabled";
 		};
 
@@ -209,6 +214,7 @@ dpaux: dpaux@545c0000 {
 			clock-names = "dpaux", "parent";
 			resets = <&tegra_car 181>;
 			reset-names = "dpaux";
+			power-domains = <&pd_sor>;
 			status = "disabled";
 
 			state_dpaux_aux: pinmux-aux {
@@ -325,7 +331,7 @@ flow-controller@60007000 {
 	};
 
 	gpio: gpio@6000d000 {
-		compatible = "nvidia,tegra210-gpio", "nvidia,tegra124-gpio", "nvidia,tegra30-gpio";
+		compatible = "nvidia,tegra210-gpio", "nvidia,tegra30-gpio";
 		reg = <0x0 0x6000d000 0x0 0x1000>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
@@ -648,27 +654,41 @@ pd_audio: aud {
 				#power-domain-cells = <0>;
 			};
 
+			pd_sor: sor {
+				clocks = <&tegra_car TEGRA210_CLK_SOR0>,
+					 <&tegra_car TEGRA210_CLK_SOR1>,
+					 <&tegra_car TEGRA210_CLK_CSI>,
+					 <&tegra_car TEGRA210_CLK_DSIA>,
+					 <&tegra_car TEGRA210_CLK_DSIB>,
+					 <&tegra_car TEGRA210_CLK_DPAUX>,
+					 <&tegra_car TEGRA210_CLK_DPAUX1>,
+					 <&tegra_car TEGRA210_CLK_MIPI_CAL>;
+				resets = <&tegra_car TEGRA210_CLK_SOR0>,
+					 <&tegra_car TEGRA210_CLK_SOR1>,
+					 <&tegra_car TEGRA210_CLK_CSI>,
+					 <&tegra_car TEGRA210_CLK_DSIA>,
+					 <&tegra_car TEGRA210_CLK_DSIB>,
+					 <&tegra_car TEGRA210_CLK_DPAUX>,
+					 <&tegra_car TEGRA210_CLK_DPAUX1>,
+					 <&tegra_car TEGRA210_CLK_MIPI_CAL>;
+				#power-domain-cells = <0>;
+			};
+
 			pd_xusbss: xusba {
 				clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>;
-				clock-names = "xusb-ss";
 				resets = <&tegra_car TEGRA210_CLK_XUSB_SS>;
-				reset-names = "xusb-ss";
 				#power-domain-cells = <0>;
 			};
 
 			pd_xusbdev: xusbb {
 				clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>;
-				clock-names = "xusb-dev";
 				resets = <&tegra_car 95>;
-				reset-names = "xusb-dev";
 				#power-domain-cells = <0>;
 			};
 
 			pd_xusbhost: xusbc {
 				clocks = <&tegra_car TEGRA210_CLK_XUSB_HOST>;
-				clock-names = "xusb-host";
 				resets = <&tegra_car TEGRA210_CLK_XUSB_HOST>;
-				reset-names = "xusb-host";
 				#power-domain-cells = <0>;
 			};
 		};
@@ -948,6 +968,7 @@ mipi: mipi@700e3000 {
 		reg = <0x0 0x700e3000 0x0 0x100>;
 		clocks = <&tegra_car TEGRA210_CLK_MIPI_CAL>;
 		clock-names = "mipi-cal";
+		power-domains = <&pd_sor>;
 		#nvidia,mipi-calibrate-cells = <1>;
 	};
 
@@ -961,6 +982,50 @@ aconnect@702c0000 {
 		#size-cells = <1>;
 		ranges = <0x702c0000 0x0 0x702c0000 0x00040000>;
 		status = "disabled";
+
+		adma: dma@702e2000 {
+			compatible = "nvidia,tegra210-adma";
+			reg = <0x702e2000 0x2000>;
+			interrupt-parent = <&agic>;
+			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&tegra_car TEGRA210_CLK_D_AUDIO>;
+			clock-names = "d_audio";
+			status = "disabled";
+		};
+
+		agic: agic@702f9000 {
+			compatible = "nvidia,tegra210-agic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x702f9000 0x2000>,
+			      <0x702fa000 0x2000>;
+			interrupts = <GIC_SPI 102 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&tegra_car TEGRA210_CLK_APE>;
+			clock-names = "clk";
+			status = "disabled";
+		};
 	};
 
 	spi@70410000 {

arch/arm64/boot/dts/qcom/Makefile

 dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb msm8916-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
 
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)

arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi

@@ -24,4 +24,52 @@ pinconf {
 			bias-pull-up;
 		};
 	};
+
+	adv7533_int_active: adv533_int_active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_int_suspend: adv7533_int_suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_active: adv7533_switch_active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_suspend: adv7533_switch_suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
 };

arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi

@@ -63,6 +63,47 @@ i2c@78b8000 {
 		/* On High speed expansion */
 			label = "HS-I2C2";
 			status = "okay";
+
+			adv_bridge: bridge@39 {
+				status = "okay";
+
+				compatible = "adi,adv7533";
+				reg = <0x39>;
+
+				interrupt-parent = <&msmgpio>;
+				interrupts = <31 2>;
+
+				adi,dsi-lanes = <4>;
+
+				pd-gpios = <&msmgpio 32 0>;
+
+				avdd-supply = <&pm8916_l6>;
+				v1p2-supply = <&pm8916_l6>;
+				v3p3-supply = <&pm8916_l17>;
+
+				pinctrl-names = "default","sleep";
+				pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+				pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						adv7533_in: endpoint {
+							remote-endpoint = <&dsi0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						adv7533_out: endpoint {
+							remote-endpoint = <&hdmi_con>;
+						};
+					};
+				};
+			};
 		};
 
 		i2c@78ba000 {
@@ -180,6 +221,36 @@ phy@78d9000 {
 		lpass@07708000 {
 			status = "okay";
 		};
+
+		mdss@1a00000 {
+			status = "okay";
+
+			mdp@1a01000 {
+				status = "okay";
+			};
+
+			dsi@1a98000 {
+				status = "okay";
+
+				vdda-supply = <&pm8916_l2>;
+				vddio-supply = <&pm8916_l6>;
+
+				ports {
+					port@1 {
+						endpoint {
+							remote-endpoint = <&adv7533_in>;
+							data-lanes = <0 1 2 3>;
+						};
+					};
+				};
+			};
+
+			dsi-phy@1a98300 {
+				status = "okay";
+
+				vddio-supply = <&pm8916_l6>;
+			};
+		};
 	};
 
 	usb2513 {
@@ -194,6 +265,17 @@ usb_id: usb-id {
 		pinctrl-names = "default";
 		pinctrl-0 = <&usb_id_default>;
 	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
 };
 
 &smd_rpm_regulators {

arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi

+/*
+ * Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+&msmgpio {
+	sdc2_cd_on: sdc2_cd_on {
+		mux {
+			pins = "gpio38";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio38";
+			bias-pull-up;		/* pull up */
+			drive-strength = <16>;	/* 16 MA */
+		};
+	};
+
+	sdc2_cd_off: sdc2_cd_off {
+		mux {
+			pins = "gpio38";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio38";
+			bias-pull-up;		/* pull up */
+			drive-strength = <2>;	/* 2 MA */
+		};
+	};
+};

arch/arm64/boot/dts/qcom/apq8096-db820c.dts

+/*
+ * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include "apq8096-db820c.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. DB820c";
+	compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc";
+};

arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi

+/*
+ * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "msm8996.dtsi"
+#include "apq8096-db820c-pins.dtsi"
+
+/ {
+	aliases {
+		serial0 = &blsp2_uart1;
+		serial1 = &blsp2_uart2;
+		i2c0	= &blsp1_i2c2;
+		i2c1	= &blsp2_i2c1;
+		i2c2	= &blsp2_i2c0;
+		spi0	= &blsp1_spi0;
+		spi1	= &blsp2_spi5;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		serial@75b0000 {
+			label = "LS-UART1";
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_uart1_2pins_default>;
+			pinctrl-1 = <&blsp2_uart1_2pins_sleep>;
+		};
+
+		serial@75b1000 {
+			label = "LS-UART0";
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_uart2_4pins_default>;
+			pinctrl-1 = <&blsp2_uart2_4pins_sleep>;
+		};
+
+		i2c@07577000 {
+		/* On Low speed expansion */
+			label = "LS-I2C0";
+			status = "okay";
+		};
+
+		i2c@075b6000 {
+		/* On Low speed expansion */
+			label = "LS-I2C1";
+			status = "okay";
+		};
+
+		spi@07575000 {
+		/* On Low speed expansion */
+			label = "LS-SPI0";
+			status = "okay";
+		};
+
+		i2c@075b5000 {
+		/* On High speed expansion */
+			label = "HS-I2C2";
+			status = "okay";
+		};
+
+		spi@075ba000{
+		/* On High speed expansion */
+			label = "HS-SPI1";
+			status = "okay";
+		};
+
+		sdhci@74a4900 {
+		/* External SD card */
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+			pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+			cd-gpios = <&msmgpio 38 0x1>;
+			status = "okay";
+		};
+	};
+};

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -86,6 +86,11 @@ wcnss@89300000 {
 			reg = <0x0 0x89300000 0x0 0x600000>;
 			no-map;
 		};
+
+		mba_mem: mba@8ea00000 {
+			no-map;
+			reg = <0 0x8ea00000 0 0x100000>;
+		};
 	};
 
 	cpus {
@@ -155,6 +160,49 @@ pmu {
 		interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>;
 	};
 
+	thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal1 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -187,10 +235,11 @@ smem {
 	};
 
 	firmware {
-		scm {
+		scm: scm {
 			compatible = "qcom,scm";
 			clocks = <&gcc GCC_CRYPTO_CLK>, <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>;
 			clock-names = "core", "bus", "iface";
+			#reset-cells = <1>;
 		};
 	};
 
@@ -228,6 +277,11 @@ tcsr_mutex_regs: syscon@1905000 {
 			reg = <0x1905000 0x20000>;
 		};
 
+		tcsr: syscon@1937000 {
+			compatible = "qcom,tcsr-msm8916", "syscon";
+			reg = <0x1937000 0x30000>;
+		};
+
 		tcsr_mutex: hwlock {
 			compatible = "qcom,tcsr-mutex";
 			syscon = <&tcsr_mutex_regs 0 0x1000>;
@@ -483,7 +537,7 @@ usb_dev: usb@78d9000 {
 			compatible = "qcom,ci-hdrc";
 			reg = <0x78d9000 0x400>;
 			dr_mode = "peripheral";
-			interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			usb-phy = <&usb_otg>;
 			status = "disabled";
 		};
@@ -491,7 +545,7 @@ usb_dev: usb@78d9000 {
 		usb_host: ehci@78d9000 {
 			compatible = "qcom,ehci-host";
 			reg = <0x78d9000 0x400>;
-			interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			usb-phy = <&usb_otg>;
 			status = "disabled";
 		};
@@ -499,8 +553,8 @@ usb_host: ehci@78d9000 {
 		usb_otg: phy@78d9000 {
 			compatible = "qcom,usb-otg-snps";
 			reg = <0x78d9000 0x400>;
-			interrupts = <GIC_SPI 134 IRQ_TYPE_EDGE_BOTH>,
-				     <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 
 			qcom,vdd-levels = <500000 1000000 1320000>;
 			qcom,phy-init-sequence = <0x44 0x6B 0x24 0x13>;
@@ -594,7 +648,7 @@ spmi_bus: spmi@200f000 {
 			      <0x200a000 0x002100>;
 			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
 			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 190 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
 			#address-cells = <2>;
@@ -609,6 +663,144 @@ rng@22000 {
 			clocks = <&gcc GCC_PRNG_AHB_CLK>;
 			clock-names = "core";
 		};
+
+		qfprom: qfprom@5c000 {
+			compatible = "qcom,qfprom";
+			reg = <0x5c000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			tsens_caldata: caldata@d0 {
+				reg = <0xd0 0x8>;
+			};
+			tsens_calsel: calsel@ec {
+				reg = <0xec 0x4>;
+			};
+		};
+
+		tsens: thermal-sensor@4a8000 {
+			compatible = "qcom,msm8916-tsens";
+			reg = <0x4a8000 0x2000>;
+			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
+			nvmem-cell-names = "calib", "calib_sel";
+			#thermal-sensor-cells = <1>;
+		};
+
+		mdss: mdss@1a00000 {
+			compatible = "qcom,mdss";
+			reg = <0x1a00000 0x1000>,
+			      <0x1ac8000 0x3000>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&gcc MDSS_GDSC>;
+
+			clocks = <&gcc GCC_MDSS_AHB_CLK>,
+				 <&gcc GCC_MDSS_AXI_CLK>,
+				 <&gcc GCC_MDSS_VSYNC_CLK>;
+			clock-names = "iface_clk",
+				      "bus_clk",
+				      "vsync_clk";
+
+			interrupts = <0 72 0>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			mdp: mdp@1a01000 {
+				compatible = "qcom,mdp5";
+				reg = <0x1a01000 0x90000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0 0>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_VSYNC_CLK>;
+				clock-names = "iface_clk",
+					      "bus_clk",
+					      "core_clk",
+					      "vsync_clk";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdp5_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+				};
+			};
+
+			dsi0: dsi@1a98000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0x1a98000 0x25c>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4 0>;
+
+				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
+						  <&gcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&dsi_phy0 0>,
+							 <&dsi_phy0 1>;
+
+				clocks = <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_BYTE0_CLK>,
+					 <&gcc GCC_MDSS_PCLK0_CLK>,
+					 <&gcc GCC_MDSS_ESC0_CLK>;
+				clock-names = "mdp_core_clk",
+					      "iface_clk",
+					      "bus_clk",
+					      "byte_clk",
+					      "pixel_clk",
+					      "core_clk";
+				phys = <&dsi_phy0>;
+				phy-names = "dsi-phy";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&mdp5_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi_phy0: dsi-phy@1a98300 {
+				compatible = "qcom,dsi-phy-28nm-lp";
+				reg = <0x1a98300 0xd4>,
+				      <0x1a98500 0x280>,
+				      <0x1a98780 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>;
+				clock-names = "iface_clk";
+			};
+		};
 	};
 
 	smd {
@@ -657,6 +849,88 @@ smd_rpm_regulators: pm8916-regulators {
 			};
 		};
 	};
+
+	hexagon-smp2p {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupts = <0 27 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 14>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		hexagon_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		hexagon_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	wcnss-smp2p {
+		compatible = "qcom,smp2p";
+		qcom,smem = <451>, <431>;
+
+		interrupts = <0 143 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 18>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <4>;
+
+		wcnss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcnss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		qcom,ipc-1 = <&apcs 0 13>;
+		qcom,ipc-6 = <&apcs 0 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		hexagon_smsm: hexagon@1 {
+			reg = <1>;
+			interrupts = <0 26 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@6 {
+			reg = <6>;
+			interrupts = <0 144 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
 };
 
 #include "msm8916-pins.dtsi"

arch/arm64/boot/dts/qcom/msm8996.dtsi

@@ -97,6 +97,92 @@ core1 {
 		};
 	};
 
+	thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 3>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal1 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 5>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal2 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 8>;
+
+			trips {
+				cpu_alert2: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit2: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal3 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 10>;
+
+			trips {
+				cpu_alert3: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit3: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -181,6 +267,12 @@ blsp2_i2c0: i2c@075b5000 {
 			status = "disabled";
 		};
 
+		tsens0: thermal-sensor@4a8000 {
+			compatible = "qcom,msm8996-tsens";
+			reg = <0x4a8000 0x2000>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		blsp2_uart1: serial@75b0000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x75b0000 0x1000>;
@@ -339,7 +431,7 @@ spmi_bus: qcom,spmi@400f000 {
 			      <0x400a000 0x002100>;
 			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
 			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 326 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
 			#address-cells = <2>;

arch/arm64/boot/dts/rockchip/Makefile

 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
 

arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts

+/*
+ * Copyright (c) 2016 Matthias Brugger <mbrugger@suse.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "rk3368.dtsi"
+
+/ {
+	model = "Rockchip Orion R68";
+	compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		pinctrl-0 = <&emmc_reset>;
+		pinctrl-names = "default";
+		reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+	keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwr_key>;
+
+		power {
+			wakeup-source;
+			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+			label = "GPIO Power";
+			linux,code = <KEY_POWER>;
+		};
+	};
+
+	leds: gpio-leds {
+		compatible = "gpio-leds";
+
+		red {
+			gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+			label = "orion:red:led";
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_ctl>;
+			default-state = "on";
+		};
+
+		blue {
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			label = "orion:blue:led";
+			pinctrl-names = "default";
+			pinctrl-0 = <&stby_pwren>;
+			default-state = "off";
+		};
+	};
+
+	vcc_18: vcc18-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	/* supplies both host and otg */
+	vcc_host: vcc-host-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "vcc_host";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_io: vcc-io-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_io";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_lan: vcc-lan-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_lan";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_sd: vcc-sd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sd";
+		gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vccio_sd: vcc-io-sd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name= "vccio_sd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_io>;
+	};
+
+	vccio_wl: vccio-wl-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vccio_wl";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_io>;
+	};
+
+	vdd_10: vdd-10-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_10";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&emmc_pwrseq>;
+	mmc-hs200-1_2v;
+	mmc-hs200-1_8v;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-gpio = <&gpio3 12 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: syr827@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-enable-ramp-delay = <300>;
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <8000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	hym8563: hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		/* rtc_int is not connected */
+	};
+};
+
+&pinctrl {
+	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+		bias-disable;
+		drive-strength = <8>;
+	};
+
+	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	emmc {
+		emmc_bus8: emmc-bus8 {
+			rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+					<1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+					<1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+					<1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+					<1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+					<1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+					<1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+					<1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+		};
+
+		emmc-clk {
+			rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+		};
+
+		emmc-cmd {
+			rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+		};
+
+		emmc_reset: emmc-reset {
+			rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	keys {
+		pwr_key: pwr-key {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	leds {
+		stby_pwren: stby-pwren {
+			rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		led_ctl: led-ctl {
+			rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_cd: sdmmc-cd {
+			rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_bus1: sdmmc-bus1 {
+			rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+	};
+
+	usb {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&saradc {
+	vref-supply = <&vcc_18>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	clock-frequency = <50000000>;
+	clock-freq-min-max = <400000 50000000>;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	keep-power-in-suspend;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_xfer>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};

arch/arm64/boot/dts/rockchip/rk3368-r88.dts

@@ -248,7 +248,6 @@ &io_domains {
 &sdio0 {
 	assigned-clocks = <&cru SCLK_SDIO0>;
 	assigned-clock-parents = <&cru PLL_CPLL>;
-	broken-cd;
 	bus-width = <4>;
 	cap-sd-highspeed;
 	cap-sdio-irq;

arch/arm64/boot/dts/rockchip/rk3368.dtsi

@@ -45,6 +45,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -641,6 +642,15 @@ pmu_io_domains: io-domains {
 			compatible = "rockchip,rk3368-pmu-io-voltage-domain";
 			status = "disabled";
 		};
+
+		reboot-mode {
+			compatible = "syscon-reboot-mode";
+			offset = <0x200>;
+			mode-normal = <BOOT_NORMAL>;
+			mode-recovery = <BOOT_RECOVERY>;
+			mode-bootloader = <BOOT_FASTBOOT>;
+			mode-loader = <BOOT_BL_DOWNLOAD>;
+		};
 	};
 
 	cru: clock-controller@ff760000 {

arch/arm64/boot/dts/rockchip/rk3399-evb.dts

@@ -49,6 +49,13 @@ / {
 	compatible = "rockchip,rk3399-evb", "rockchip,rk3399",
 		     "google,rk3399evb-rev2";
 
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
+	};
+
 	vdd_center: vdd-center {
 		compatible = "pwm-regulator";
 		pwms = <&pwm3 0 25000 0>;
@@ -69,18 +76,61 @@ vcc3v3_sys: vcc3v3-sys {
 		regulator-max-microvolt = <3300000>;
 	};
 
+	vcc5v0_sys: vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en>;
+		regulator-name = "vcc5v0_host";
+		vin-supply = <&vcc5v0_sys>;
+	};
+
 	vcc_phy: vcc-phy-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_phy";
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	vcc_phy: vcc-phy-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_phy";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 };
 
 &emmc_phy {
 	status = "okay";
 };
 
+&gmac {
+	assigned-clocks = <&cru SCLK_RMII_SRC>;
+	assigned-clock-parents = <&clkin_gmac>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_phy>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-gpio = <&gpio3 15 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x28>;
+	rx_delay = <0x11>;
+	status = "okay";
+};
+
 &pwm0 {
 	status = "okay";
 };
@@ -101,6 +151,36 @@ &sdhci {
 	status = "okay";
 };
 
+&pcie_phy {
+	status = "disabled";
+};
+
+&pcie0 {
+	ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	num-lanes = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_clkreqn>;
+	status = "disabled";
+};
+
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
+&u2phy1 {
+	status = "okay";
+};
+
+&u2phy1_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
 &uart2 {
 	status = "okay";
 };
@@ -133,4 +213,11 @@ pmic_dvs2: pmic-dvs2 {
 				<1 18 RK_FUNC_GPIO &pcfg_pull_down>;
 		};
 	};
+
+	usb2 {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins =
+				<4 25 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };

arch/arm64/boot/dts/socionext/Makefile

-dtb-$(CONFIG_ARCH_UNIPHIER) += uniphier-ph1-ld20-ref.dtb
+dtb-$(CONFIG_ARCH_UNIPHIER) += \
+	uniphier-ld11-ref.dtb \
+	uniphier-ld20-ref.dtb
 
 always		:= $(dtb-y)
 clean-files	:= *.dtb

arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts

+/*
+ * Device Tree Source for UniPhier LD11 Reference Board
+ *
+ * Copyright (C) 2016 Socionext Inc.
+ *   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "uniphier-ld11.dtsi"
+/include/ "uniphier-ref-daughter.dtsi"
+/include/ "uniphier-support-card.dtsi"
+
+/ {
+	model = "UniPhier LD11 Reference Board";
+	compatible = "socionext,uniphier-ld11-ref", "socionext,uniphier-ld11";
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x80000000 0 0x40000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+	};
+};
+
+&ethsc {
+	interrupts = <0 48 4>;
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};

arch/arm64/boot/dts/socionext/uniphier-ph1-ld20-ref.dts → arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts

 /*
- * Device Tree Source for UniPhier PH1-LD20 Reference Board
+ * Device Tree Source for UniPhier LD20 Reference Board
  *
- * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ * Copyright (C) 2015-2016 Socionext Inc.
+ *   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -43,13 +44,13 @@
  */
 
 /dts-v1/;
-/include/ "uniphier-ph1-ld20.dtsi"
+/include/ "uniphier-ld20.dtsi"
 /include/ "uniphier-ref-daughter.dtsi"
 /include/ "uniphier-support-card.dtsi"
 
 / {
-	model = "UniPhier PH1-LD20 Reference Board";
-	compatible = "socionext,ph1-ld20-ref", "socionext,ph1-ld20";
+	model = "UniPhier LD20 Reference Board";
+	compatible = "socionext,uniphier-ld20-ref", "socionext,uniphier-ld20";
 
 	memory {
 		device_type = "memory";

arch/arm64/boot/dts/socionext/uniphier-ph1-ld20.dtsi → arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi

 /*
- * Device Tree Source for UniPhier PH1-LD20 SoC
+ * Device Tree Source for UniPhier LD20 SoC
  *
- * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ * Copyright (C) 2015-2016 Socionext Inc.
+ *   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -45,7 +46,7 @@
 /memreserve/ 0x80000000 0x00000008;	/* cpu-release-addr */
 
 / {
-	compatible = "socionext,ph1-ld20";
+	compatible = "socionext,uniphier-ld20";
 	#address-cells = <2>;
 	#size-cells = <2>;
 	interrupt-parent = <&gic>;
@@ -113,18 +114,6 @@ refclk: ref {
 			#clock-cells = <0>;
 			clock-frequency = <25000000>;
 		};
-
-		uart_clk: uart_clk {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <58820000>;
-		};
-
-		i2c_clk: i2c_clk {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <50000000>;
-		};
 	};
 
 	timer {
@@ -148,7 +137,7 @@ serial0: serial@54006800 {
 			interrupts = <0 33 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
-			clocks = <&uart_clk>;
+			clocks = <&peri_clk 0>;
 		};
 
 		serial1: serial@54006900 {
@@ -158,7 +147,7 @@ serial1: serial@54006900 {
 			interrupts = <0 35 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
-			clocks = <&uart_clk>;
+			clocks = <&peri_clk 1>;
 		};
 
 		serial2: serial@54006a00 {
@@ -168,7 +157,7 @@ serial2: serial@54006a00 {
 			interrupts = <0 37 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
-			clocks = <&uart_clk>;
+			clocks = <&peri_clk 2>;
 		};
 
 		serial3: serial@54006b00 {
@@ -178,7 +167,7 @@ serial3: serial@54006b00 {
 			interrupts = <0 177 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
-			clocks = <&uart_clk>;
+			clocks = <&peri_clk 3>;
 		};
 
 		i2c0: i2c@58780000 {
@@ -190,7 +179,7 @@ i2c0: i2c@58780000 {
 			interrupts = <0 41 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
-			clocks = <&i2c_clk>;
+			clocks = <&peri_clk 4>;
 			clock-frequency = <100000>;
 		};
 
@@ -203,7 +192,7 @@ i2c1: i2c@58781000 {
 			interrupts = <0 42 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
-			clocks = <&i2c_clk>;
+			clocks = <&peri_clk 5>;
 			clock-frequency = <100000>;
 		};
 
@@ -213,7 +202,7 @@ i2c2: i2c@58782000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <0 43 4>;
-			clocks = <&i2c_clk>;
+			clocks = <&peri_clk 6>;
 			clock-frequency = <400000>;
 		};
 
@@ -226,7 +215,7 @@ i2c3: i2c@58783000 {
 			interrupts = <0 44 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
-			clocks = <&i2c_clk>;
+			clocks = <&peri_clk 7>;
 			clock-frequency = <100000>;
 		};
 
@@ -239,7 +228,7 @@ i2c4: i2c@58784000 {
 			interrupts = <0 45 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c4>;
-			clocks = <&i2c_clk>;
+			clocks = <&peri_clk 8>;
 			clock-frequency = <100000>;
 		};
 
@@ -249,7 +238,7 @@ i2c5: i2c@58785000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <0 25 4>;
-			clocks = <&i2c_clk>;
+			clocks = <&peri_clk 9>;
 			clock-frequency = <400000>;
 		};
 
@@ -259,6 +248,8 @@ system_bus: system-bus@58c00000 {
 			reg = <0x58c00000 0x400>;
 			#address-cells = <2>;
 			#size-cells = <1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_system_bus>;
 		};
 
 		smpctrl@59800000 {
@@ -266,12 +257,45 @@ smpctrl@59800000 {
 			reg = <0x59801000 0x400>;
 		};
 
+		mioctrl@59810000 {
+			compatible = "socionext,uniphier-mioctrl",
+				     "simple-mfd", "syscon";
+			reg = <0x59810000 0x800>;
+
+			mio_clk: clock {
+				compatible = "socionext,uniphier-ld20-mio-clock";
+				#clock-cells = <1>;
+			};
+
+			mio_rst: reset {
+				compatible = "socionext,uniphier-ld20-mio-reset";
+				#reset-cells = <1>;
+			};
+		};
+
+		perictrl@59820000 {
+			compatible = "socionext,uniphier-perictrl",
+				     "simple-mfd", "syscon";
+			reg = <0x59820000 0x200>;
+
+			peri_clk: clock {
+				compatible = "socionext,uniphier-ld20-peri-clock";
+				#clock-cells = <1>;
+			};
+
+			peri_rst: reset {
+				compatible = "socionext,uniphier-ld20-peri-reset";
+				#reset-cells = <1>;
+			};
+		};
+
 		soc-glue@5f800000 {
-			compatible = "simple-mfd", "syscon";
+			compatible = "socionext,uniphier-soc-glue",
+				     "simple-mfd", "syscon";
 			reg = <0x5f800000 0x2000>;
 
 			pinctrl: pinctrl {
-				 compatible = "socionext,uniphier-ld20-pinctrl";
+				compatible = "socionext,uniphier-ld20-pinctrl";
 			};
 		};
 
@@ -283,6 +307,22 @@ gic: interrupt-controller@5fe00000 {
 			#interrupt-cells = <3>;
 			interrupts = <1 9 4>;
 		};
+
+		sysctrl@61840000 {
+			compatible = "socionext,uniphier-sysctrl",
+				     "simple-mfd", "syscon";
+			reg = <0x61840000 0x4000>;
+
+			sys_clk: clock {
+				compatible = "socionext,uniphier-ld20-clock";
+				#clock-cells = <1>;
+			};
+
+			sys_rst: reset {
+				compatible = "socionext,uniphier-ld20-reset";
+				#reset-cells = <1>;
+			};
+		};
 	};
 };
 

arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts

@@ -29,7 +29,7 @@ chosen {
 
 	memory {
 		device_type = "memory";
-		reg = <0x0 0x0 0x40000000>;
+		reg = <0x0 0x0 0x0 0x40000000>;
 	};
 };