Commit a4f28c00 authored by Mark Brown's avatar Mark Brown

ASoC: Provide microphone bias configuration for WM8962

Add the widget for MICBIAS power control and allow configuration of the
microphone bias setup via the platform data for the WM8962. When
microphone status signals are brought out to GPIO this should be
sufficient to enable microphone detection.
Signed-off-by: default avatarMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: default avatarLiam Girdwood <lrg@slimlogic.co.uk>
parent dee0bb9d
...@@ -17,6 +17,12 @@ ...@@ -17,6 +17,12 @@
struct wm8962_pdata { struct wm8962_pdata {
u32 gpio_init[WM8962_MAX_GPIO]; u32 gpio_init[WM8962_MAX_GPIO];
/* Setup for microphone detection, raw value to be written to
* R48(0x30) - only microphone related bits will be updated.
* Detection may be enabled here for use with signals brought
* out on the GPIOs. */
u32 mic_cfg;
bool irq_active_low; bool irq_active_low;
bool spk_mono; /* Speaker outputs tied together as mono */ bool spk_mono; /* Speaker outputs tied together as mono */
......
...@@ -630,6 +630,8 @@ SND_SOC_DAPM_INPUT("IN4L"), ...@@ -630,6 +630,8 @@ SND_SOC_DAPM_INPUT("IN4L"),
SND_SOC_DAPM_INPUT("IN4R"), SND_SOC_DAPM_INPUT("IN4R"),
SND_SOC_DAPM_INPUT("Beep"), SND_SOC_DAPM_INPUT("Beep"),
SND_SOC_DAPM_MICBIAS("MICBIAS", WM8962_PWR_MGMT_1, 1, 0),
SND_SOC_DAPM_SUPPLY("Class G", WM8962_CHARGE_PUMP_B, 0, 1, NULL, 0), SND_SOC_DAPM_SUPPLY("Class G", WM8962_CHARGE_PUMP_B, 0, 1, NULL, 0),
SND_SOC_DAPM_SUPPLY("SYSCLK", WM8962_CLOCKING2, 5, 0, sysclk_event, SND_SOC_DAPM_SUPPLY("SYSCLK", WM8962_CLOCKING2, 5, 0, sysclk_event,
SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD), SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
...@@ -1755,6 +1757,16 @@ static int wm8962_probe(struct snd_soc_codec *codec) ...@@ -1755,6 +1757,16 @@ static int wm8962_probe(struct snd_soc_codec *codec)
if (pdata->spk_mono) if (pdata->spk_mono)
wm8962->reg_cache[WM8962_CLASS_D_CONTROL_2] wm8962->reg_cache[WM8962_CLASS_D_CONTROL_2]
|= WM8962_SPK_MONO; |= WM8962_SPK_MONO;
/* Micbias setup, detection enable and detection
* threasholds. */
if (pdata->mic_cfg)
snd_soc_update_bits(codec, WM8962_ADDITIONAL_CONTROL_4,
WM8962_MICDET_ENA |
WM8962_MICDET_THR_MASK |
WM8962_MICSHORT_THR_MASK |
WM8962_MICBIAS_LVL,
pdata->mic_cfg);
} }
/* Latch volume update bits */ /* Latch volume update bits */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment