media: usb: dvb-usb: remove old friio driver

friio drivers is unused and un-compilable since
commit b30cc07d ("media: dvb-usb/friio, dvb-usb-v2/gl861: decompose
friio and merge with gl861"). Let's remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Cc: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

drivers/media/usb/dvb-usb/friio.h

-/* DVB USB compliant Linux driver for the Friio USB2.0 ISDB-T receiver.
- *
- * Copyright (C) 2009 Akihiro Tsukada <tskd2@yahoo.co.jp>
- *
- * This module is based off the the gl861 and vp702x modules.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the Free
- * Software Foundation, version 2.
- *
- * see Documentation/media/dvb-drivers/dvb-usb.rst for more information
- */
-#ifndef _DVB_USB_FRIIO_H_
-#define _DVB_USB_FRIIO_H_
-
-/**
- *      Friio Components
- *       USB hub:                                AU4254
- *         USB controller(+ TS dmx & streaming): GL861
- *         Frontend:                             comtech JDVBT-90502
- *             (tuner PLL:                       tua6034, I2C addr:(0xC0 >> 1))
- *             (OFDM demodulator:                TC90502, I2C addr:(0x30 >> 1))
- *         LED x3 (+LNB) control:                PIC 16F676
- *         EEPROM:                               24C08
- *
- *        (USB smart card reader:                AU9522)
- *
- */
-
-#define DVB_USB_LOG_PREFIX "friio"
-#include "dvb-usb.h"
-
-extern int dvb_usb_friio_debug;
-#define deb_info(args...) dprintk(dvb_usb_friio_debug, 0x01, args)
-#define deb_xfer(args...) dprintk(dvb_usb_friio_debug, 0x02, args)
-#define deb_rc(args...)   dprintk(dvb_usb_friio_debug, 0x04, args)
-#define deb_fe(args...)   dprintk(dvb_usb_friio_debug, 0x08, args)
-
-/* Vendor requests */
-#define GL861_WRITE		0x40
-#define GL861_READ		0xc0
-
-/* command bytes */
-#define GL861_REQ_I2C_WRITE	0x01
-#define GL861_REQ_I2C_READ	0x02
-/* For control msg with data argument */
-/* Used for accessing the PLL on the secondary I2C bus of FE via GL861 */
-#define GL861_REQ_I2C_DATA_CTRL_WRITE	0x03
-
-#define GL861_ALTSETTING_COUNT	2
-#define FRIIO_BULK_ALTSETTING	0
-#define FRIIO_ISOC_ALTSETTING	1
-
-/* LED & LNB control via PIC. */
-/* basically, it's serial control with clock and strobe. */
-/* write the below 4bit control data to the reg 0x00 at the I2C addr 0x00 */
-/* when controlling the LEDs, 32bit(saturation, R, G, B) is sent on the bit3*/
-#define FRIIO_CTL_LNB (1 << 0)
-#define FRIIO_CTL_STROBE (1 << 1)
-#define FRIIO_CTL_CLK (1 << 2)
-#define FRIIO_CTL_LED (1 << 3)
-
-/* Front End related */
-
-#define FRIIO_DEMOD_ADDR  (0x30 >> 1)
-#define FRIIO_PLL_ADDR  (0xC0 >> 1)
-
-#define JDVBT90502_PLL_CLK	4000000
-#define JDVBT90502_PLL_DIVIDER	28
-
-#define JDVBT90502_2ND_I2C_REG 0xFE
-
-/* byte index for pll i2c command data structure*/
-/* see datasheet for tua6034 */
-#define DEMOD_REDIRECT_REG 0
-#define ADDRESS_BYTE       1
-#define DIVIDER_BYTE1      2
-#define DIVIDER_BYTE2      3
-#define CONTROL_BYTE       4
-#define BANDSWITCH_BYTE    5
-#define AGC_CTRL_BYTE      5
-#define PLL_CMD_LEN        6
-
-/* bit masks for PLL STATUS response */
-#define PLL_STATUS_POR_MODE   0x80 /* 1: Power on Reset (test) Mode */
-#define PLL_STATUS_LOCKED     0x40 /* 1: locked */
-#define PLL_STATUS_AGC_ACTIVE 0x08 /* 1:active */
-#define PLL_STATUS_TESTMODE   0x07 /* digital output level (5 level) */
-  /* 0.15Vcc step   0x00: < 0.15Vcc, ..., 0x04: >= 0.6Vcc (<= 1Vcc) */
-
-
-struct jdvbt90502_config {
-	u8 demod_address; /* i2c addr for demodulator IC */
-	u8 pll_address;   /* PLL addr on the secondary i2c*/
-};
-extern struct jdvbt90502_config friio_fe_config;
-
-extern struct dvb_frontend *jdvbt90502_attach(struct dvb_usb_device *d);
-#endif