Commit ac4ce718 authored by Barry Song's avatar Barry Song Committed by Greg Kroah-Hartman

serial: sirf: only use lookup table to set baudrate when ioclk=150MHz

The fast lookup table to set baudrate is only right when ioclk
is 150MHz. for most platforms, ioclk is 150MHz, but some boards
might set ioclk to other frequency.

so re-calc the clk_div_reg when ioclk is not 150MHz. this patch
also gets clk in probe and puts it in remove.
Signed-off-by: default avatarBarry Song <Baohua.Song@csr.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent e27a7d79
......@@ -357,7 +357,6 @@ static void sirfsoc_uart_set_termios(struct uart_port *port,
struct ktermios *old)
{
struct sirfsoc_uart_port *sirfport = to_sirfport(port);
unsigned long ioclk_rate;
unsigned long config_reg = 0;
unsigned long baud_rate;
unsigned long setted_baud;
......@@ -369,7 +368,6 @@ static void sirfsoc_uart_set_termios(struct uart_port *port,
int threshold_div;
int temp;
ioclk_rate = 150000000;
switch (termios->c_cflag & CSIZE) {
default:
case CS8:
......@@ -425,14 +423,17 @@ static void sirfsoc_uart_set_termios(struct uart_port *port,
sirfsoc_uart_disable_ms(port);
}
/* common rate: fast calculation */
for (ic = 0; ic < SIRF_BAUD_RATE_SUPPORT_NR; ic++)
if (baud_rate == baudrate_to_regv[ic].baud_rate)
clk_div_reg = baudrate_to_regv[ic].reg_val;
if (port->uartclk == 150000000) {
/* common rate: fast calculation */
for (ic = 0; ic < SIRF_BAUD_RATE_SUPPORT_NR; ic++)
if (baud_rate == baudrate_to_regv[ic].baud_rate)
clk_div_reg = baudrate_to_regv[ic].reg_val;
}
setted_baud = baud_rate;
/* arbitary rate setting */
if (unlikely(clk_div_reg == 0))
clk_div_reg = sirfsoc_calc_sample_div(baud_rate, ioclk_rate,
clk_div_reg = sirfsoc_calc_sample_div(baud_rate, port->uartclk,
&setted_baud);
wr_regl(port, SIRFUART_DIVISOR, clk_div_reg);
......@@ -691,6 +692,14 @@ int sirfsoc_uart_probe(struct platform_device *pdev)
goto err;
}
sirfport->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(sirfport->clk)) {
ret = PTR_ERR(sirfport->clk);
goto clk_err;
}
clk_prepare_enable(sirfport->clk);
port->uartclk = clk_get_rate(sirfport->clk);
port->ops = &sirfsoc_uart_ops;
spin_lock_init(&port->lock);
......@@ -704,6 +713,9 @@ int sirfsoc_uart_probe(struct platform_device *pdev)
return 0;
port_err:
clk_disable_unprepare(sirfport->clk);
clk_put(sirfport->clk);
clk_err:
platform_set_drvdata(pdev, NULL);
if (sirfport->hw_flow_ctrl)
pinctrl_put(sirfport->p);
......@@ -718,6 +730,8 @@ static int sirfsoc_uart_remove(struct platform_device *pdev)
platform_set_drvdata(pdev, NULL);
if (sirfport->hw_flow_ctrl)
pinctrl_put(sirfport->p);
clk_disable_unprepare(sirfport->clk);
clk_put(sirfport->clk);
uart_remove_one_port(&sirfsoc_uart_drv, port);
return 0;
}
......
......@@ -163,6 +163,7 @@ struct sirfsoc_uart_port {
struct uart_port port;
struct pinctrl *p;
struct clk *clk;
};
/* Hardware Flow Control */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment