Commit add7b58e authored by Bjorn Helgaas's avatar Bjorn Helgaas Committed by Russell King

[SERIAL] support the Exsys EX-4055 4S four-port card

Tested by Wolfgang Denk with this device:

    00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
        Subsystem: Exsys EX-4055 4S(16C550) RS-232
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
        Region 1: I/O ports at 7080 [size=128]
        Region 2: I/O ports at 7400 [size=32]

    00:0f.0 Class 0280: 10b5:9050 (rev 01)
        Subsystem: d84d:4055

Results with this patch:

    Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    PCI: Found IRQ 10 for device 0000:00:0f.0
    ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
    ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
    ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
    ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: default avatarBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
parent d5c5d8fe
......@@ -226,8 +226,10 @@ static int __devinit pci_plx9050_init(struct pci_dev *dev)
}
irq_config = 0x41;
if (dev->vendor == PCI_VENDOR_ID_PANACOM)
if (dev->vendor == PCI_VENDOR_ID_PANACOM ||
dev->subsystem_vendor == PCI_SUBVENDOR_ID_EXSYS) {
irq_config = 0x43;
}
if ((dev->vendor == PCI_VENDOR_ID_PLX) &&
(dev->device == PCI_DEVICE_ID_PLX_ROMULUS)) {
/*
......@@ -661,6 +663,15 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
/*
* PLX
*/
{
.vendor = PCI_VENDOR_ID_PLX,
.device = PCI_DEVICE_ID_PLX_9050,
.subvendor = PCI_SUBVENDOR_ID_EXSYS,
.subdevice = PCI_SUBDEVICE_ID_EXSYS_4055,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
{
.vendor = PCI_VENDOR_ID_PLX,
.device = PCI_DEVICE_ID_PLX_9050,
......@@ -927,6 +938,7 @@ enum pci_board_num_t {
pbn_panacom,
pbn_panacom2,
pbn_panacom4,
pbn_exsys_4055,
pbn_plx_romulus,
pbn_oxsemi,
pbn_intel_i960,
......@@ -1292,6 +1304,13 @@ static struct pciserial_board pci_boards[] __devinitdata = {
.reg_shift = 7,
},
[pbn_exsys_4055] = {
.flags = FL_BASE2,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
/* I think this entry is broken - the first_offset looks wrong --rmk */
[pbn_plx_romulus] = {
.flags = FL_BASE2,
......@@ -1853,6 +1872,10 @@ static struct pci_device_id serial_pci_tbl[] = {
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
PCI_SUBDEVICE_ID_CHASE_PCIRAS8, 0, 0,
pbn_b2_8_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_EXSYS,
PCI_SUBDEVICE_ID_EXSYS_4055, 0, 0,
pbn_exsys_4055 },
/*
* Megawolf Romulus PCI Serial Card, from Mike Hudson
* (Exoray@isys.ca)
......
......@@ -2696,6 +2696,7 @@
#define PCI_SUBVENDOR_ID_EXSYS 0xd84d
#define PCI_SUBDEVICE_ID_EXSYS_4014 0x4014
#define PCI_SUBDEVICE_ID_EXSYS_4055 0x4055
#define PCI_VENDOR_ID_TIGERJET 0xe159
#define PCI_DEVICE_ID_TIGERJET_300 0x0001
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment