Merge tag 'mvebu-dt64-4.15-1' of git://git.infradead.org/linux-mvebu into next/dt

Pull "mvebu dt64 for 4.15 (part 1)" from Gregory CLEMENT:

On Armada 7K/8k:
- Improve network support at SoC and board level
- Enable watchdog
- Add UART muxing
- On 7040 DB: add CD SDIO and NAND support
- On 8040 DB: add PCIE more ports and SPI1

On Armada 37xx:
 - Fix UART register size
 - Add vmmc regulator for SD on 3720 DB

* tag 'mvebu-dt64-4.15-1' of git://git.infradead.org/linux-mvebu:
  arm64: dts: marvell: 7040-db: Add the carrier detect pin for SD card on CP
  arm64: dts: marvell: 7040-db: Document the gpio expander
  arm64: dts: marvell: enable additional PCIe ports on Armada 8040 DB
  arm64: dts: marvell: add NAND support on the 7040-DB board
  arm64: dts: marvell: Enable Armada-8040-DB CPS SPI1
  arm64: dts: marvell: 8040-db: enable the SFP ports
  arm64: dts: marvell: 7040-db: enable the SFP port
  arm64: dts: marvell: 7040-db: add comphy reference to Ethernet port
  arm64: dts: marvell: mcbin: add comphy references to Ethernet ports
  arm64: dts: marvell: 37xx: remove empty line
  arm64: dts: marvell: cp110: add PPv2 port interrupts
  arm64: dts: marvell: add comphy nodes on cp110 master and slave
  arm64: dts: marvell: extend the cp110 syscon register area length
  arm64: dts: marvell: enable AP806 watchdog
  arm64: dts: marvell: Fix A37xx UART0 register size
  arm64: dts: marvell: armada-3720-db: Add vmmc regulator for SD slot
  arm64: dts: marvell: add UART muxing on Armada 7K/8K

Documentation/devicetree/bindings/serial/mvebu-uart.txt

@@ -8,6 +8,6 @@ Required properties:
 Example:
 	serial@12000 {
 		compatible = "marvell,armada-3700-uart";
-		reg = <0x12000 0x400>;
+		reg = <0x12000 0x200>;
 		interrupts = <43>;
 	};

arch/arm64/boot/dts/marvell/armada-3720-db.dts

@@ -94,6 +94,16 @@ vcc_sd_reg1: regulator {
 			  3300000 0x0>;
 		enable-active-high;
 	};
+
+	vcc_sd_reg2: regulator-vmcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sd2";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio_exp 4 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 /* Gigabit module on CON19(V2.0)/CON21(V1.4) */
@@ -179,6 +189,7 @@ &sdhci1 {
 	bus-width = <4>;
 	marvell,pad-type = "sd";
 	vqmmc-supply = <&vcc_sd_reg1>;
+	vmmc-supply = <&vcc_sd_reg2>;
 	status = "okay";
 };
 

arch/arm64/boot/dts/marvell/armada-37xx.dtsi

@@ -134,7 +134,7 @@ i2c1: i2c@11080 {
 
 			uart0: serial@12000 {
 				compatible = "marvell,armada-3700-uart";
-				reg = <0x12000 0x400>;
+				reg = <0x12000 0x200>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 			};
@@ -183,7 +183,6 @@ gpionb: gpio {
 					<GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
 				};
 
 				xtalclk: xtal-clk {

arch/arm64/boot/dts/marvell/armada-7040-db.dts

@@ -124,6 +124,8 @@ partition@400000 {
 
 &uart0 {
 	status = "okay";
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
 };
 
 
@@ -141,9 +143,49 @@ expander0: pca9555@21 {
 		gpio-controller;
 		#gpio-cells = <2>;
 		reg = <0x21>;
+		/*
+		 * IO0_0: USB3_PWR_EN0	IO1_0: USB_3_1_Dev_Detect
+		 * IO0_1: USB3_PWR_EN1	IO1_1: USB2_1_current_limit
+		 * IO0_2: DDR3_4_Detect	IO1_2: Hcon_IO_RstN
+		 * IO0_3: USB2_DEVICE_DETECT
+		 * IO0_4: GPIO_0	IO1_4: SD_Status
+		 * IO0_5: GPIO_1	IO1_5: LDO_5V_Enable
+		 * IO0_6: IHB_5V_Enable	IO1_6: PWR_EN_eMMC
+		 * IO0_7:		IO1_7: SDIO_Vcntrl
+		 */
 	};
 };
 
+&cpm_nand {
+	/*
+	 * SPI on CPM and NAND have common pins on this board. We can
+	 * use only one at a time. To enable the NAND (whihch will
+	 * disable the SPI), the "status = "okay";" line have to be
+	 * added here.
+	 */
+	num-cs = <1>;
+	pinctrl-0 = <&nand_pins>, <&nand_rb>;
+	pinctrl-names = "default";
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+	marvell,nand-enable-arbiter;
+	nand-on-flash-bbt;
+
+	partition@0 {
+		label = "U-Boot";
+		reg = <0 0x200000>;
+	};
+	partition@200000 {
+		label = "Linux";
+		reg = <0x200000 0xe00000>;
+	};
+	partition@1000000 {
+		label = "Filesystem";
+		reg = <0x1000000 0x3f000000>;
+	};
+};
+
+
 &cpm_spi1 {
 	status = "okay";
 
@@ -197,7 +239,7 @@ &cpm_sdhci0 {
 	status = "okay";
 	bus-width = <4>;
 	no-1-8-v;
-	non-removable;
+	cd-gpios = <&expander0 12 GPIO_ACTIVE_LOW>;
 };
 
 &cpm_mdio {
@@ -215,10 +257,21 @@ &cpm_ethernet {
 	status = "okay";
 };
 
+&cpm_eth0 {
+	status = "okay";
+	/* Network PHY */
+	phy-mode = "10gbase-kr";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cpm_comphy2 0>;
+};
+
 &cpm_eth1 {
 	status = "okay";
+	/* Network PHY */
 	phy = <&phy0>;
 	phy-mode = "sgmii";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cpm_comphy0 1>;
 };
 
 &cpm_eth2 {

arch/arm64/boot/dts/marvell/armada-70x0.dtsi

@@ -64,5 +64,19 @@ &cpm_gpio2 {
 &cpm_syscon0 {
 	cpm_pinctrl: pinctrl {
 		compatible = "marvell,armada-7k-pinctrl";
+
+		nand_pins: nand-pins {
+			marvell,pins =
+			"mpp15", "mpp16", "mpp17", "mpp18",
+			"mpp19", "mpp20", "mpp21", "mpp22",
+			"mpp23", "mpp24", "mpp25", "mpp26",
+			"mpp27";
+			marvell,function = "dev";
+		};
+
+		nand_rb: nand-rb {
+			marvell,pins = "mpp13";
+			marvell,function = "nf";
+		};
 	};
 };

arch/arm64/boot/dts/marvell/armada-8040-db.dts

@@ -139,8 +139,14 @@ partition@400000 {
 /* Accessible over the mini-USB CON9 connector on the main board */
 &uart0 {
 	status = "okay";
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
 };
 
+/* CON6 on CP0 expansion */
+&cpm_pcie0 {
+	status = "okay";
+};
 
 /* CON5 on CP0 expansion */
 &cpm_pcie2 {
@@ -200,12 +206,27 @@ &cpm_ethernet {
 	status = "okay";
 };
 
+&cpm_eth0 {
+	status = "okay";
+	phy-mode = "10gbase-kr";
+};
+
 &cpm_eth2 {
 	status = "okay";
 	phy = <&phy1>;
 	phy-mode = "rgmii-id";
 };
 
+/* CON6 on CP1 expansion */
+&cps_pcie0 {
+	status = "okay";
+};
+
+/* CON7 on CP1 expansion */
+&cps_pcie1 {
+	status = "okay";
+};
+
 /* CON5 on CP1 expansion */
 &cps_pcie2 {
 	status = "okay";
@@ -216,6 +237,37 @@ &cps_i2c0 {
 	clock-frequency = <100000>;
 };
 
+&cps_spi1 {
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <20000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "Boot";
+				reg = <0x0 0x200000>;
+			};
+			partition@200000 {
+				label = "Filesystem";
+				reg = <0x200000 0xd00000>;
+			};
+			partition@f00000 {
+				label = "Boot_2nd";
+				reg = <0xf00000 0x100000>;
+			};
+		};
+	};
+};
+
 /* CON4 on CP1 expansion */
 &cps_sata0 {
 	status = "okay";
@@ -244,6 +296,11 @@ &cps_ethernet {
 	status = "okay";
 };
 
+&cps_eth0 {
+	status = "okay";
+	phy-mode = "10gbase-kr";
+};
+
 &cps_eth1 {
 	status = "okay";
 	phy = <&phy0>;

arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts

@@ -101,6 +101,8 @@ usb3h0_phy: usb3_phy0 {
 
 &uart0 {
 	status = "okay";
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
 };
 
 &ap_sdhci0 {
@@ -222,8 +224,11 @@ &cpm_ethernet {
 
 &cpm_eth0 {
 	status = "okay";
+	/* Network PHY */
 	phy = <&phy0>;
 	phy-mode = "10gbase-kr";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cpm_comphy4 0>;
 };
 
 &cpm_sata0 {
@@ -257,15 +262,21 @@ &cps_ethernet {
 
 &cps_eth0 {
 	status = "okay";
+	/* Network PHY */
 	phy = <&phy8>;
 	phy-mode = "10gbase-kr";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cps_comphy4 0>;
 };
 
 &cps_eth1 {
 	/* CPS Lane 0 - J5 (Gigabit RJ45) */
 	status = "okay";
+	/* Network PHY */
 	phy = <&ge_phy>;
 	phy-mode = "sgmii";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cps_comphy0 1>;
 };
 
 &cps_pinctrl {

arch/arm64/boot/dts/marvell/armada-ap806.dtsi

@@ -241,6 +241,12 @@ uart1: serial@512100 {
 
 			};
 
+			watchdog: watchdog@600000 {
+				compatible = "arm,sbsa-gwdt";
+				reg = <0x610000 0x1000>, <0x600000 0x1000>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
 			ap_sdhci0: sdhci@6e0000 {
 				compatible = "marvell,armada-ap806-sdhci";
 				reg = <0x6e0000 0x300>;
@@ -263,6 +269,11 @@ ap_clk: clock {
 
 				ap_pinctrl: pinctrl {
 					compatible = "marvell,ap806-pinctrl";
+
+					uart0_pins: uart0-pins {
+						marvell,pins = "mpp11", "mpp19";
+						marvell,function = "uart0";
+					};
 				};
 
 				ap_gpio: gpio@1040 {

arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi

@@ -74,9 +74,10 @@ cpm_eth0: eth0 {
 						     <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>;
+						     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>,
+						     <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared";
+							  "tx-cpu3", "rx-shared", "link";
 					port-id = <0>;
 					gop-port-id = <0>;
 					status = "disabled";
@@ -87,9 +88,10 @@ cpm_eth1: eth1 {
 						     <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>;
+						     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>,
+						     <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared";
+							  "tx-cpu3", "rx-shared", "link";
 					port-id = <1>;
 					gop-port-id = <2>;
 					status = "disabled";
@@ -100,15 +102,54 @@ cpm_eth2: eth2 {
 						     <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>;
+						     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>,
+						     <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared";
+							  "tx-cpu3", "rx-shared", "link";
 					port-id = <2>;
 					gop-port-id = <3>;
 					status = "disabled";
 				};
 			};
 
+			cpm_comphy: phy@120000 {
+				compatible = "marvell,comphy-cp110";
+				reg = <0x120000 0x6000>;
+				marvell,system-controller = <&cpm_syscon0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				cpm_comphy0: phy@0 {
+					reg = <0>;
+					#phy-cells = <1>;
+				};
+
+				cpm_comphy1: phy@1 {
+					reg = <1>;
+					#phy-cells = <1>;
+				};
+
+				cpm_comphy2: phy@2 {
+					reg = <2>;
+					#phy-cells = <1>;
+				};
+
+				cpm_comphy3: phy@3 {
+					reg = <3>;
+					#phy-cells = <1>;
+				};
+
+				cpm_comphy4: phy@4 {
+					reg = <4>;
+					#phy-cells = <1>;
+				};
+
+				cpm_comphy5: phy@5 {
+					reg = <5>;
+					#phy-cells = <1>;
+				};
+			};
+
 			cpm_mdio: mdio@12a200 {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -143,7 +184,7 @@ cpm_rtc: rtc@284000 {
 
 			cpm_syscon0: system-controller@440000 {
 				compatible = "syscon", "simple-mfd";
-				reg = <0x440000 0x1000>;
+				reg = <0x440000 0x2000>;
 
 				cpm_clk: clock {
 					compatible = "marvell,cp110-clock";
@@ -274,12 +315,14 @@ cpm_nand: nand@720000 {
 				 * this controller is only usable on the CPM
 				 * for A7K and on the CPS for A8K.
 				 */
-				compatible = "marvell,armada370-nand";
+				compatible = "marvell,armada-8k-nand",
+					     "marvell,armada370-nand";
 				reg = <0x720000 0x54>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				interrupts = <ICU_GRP_NSR 115 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&cpm_clk 1 2>;
+				marvell,system-controller = <&cpm_syscon0>;
 				status = "disabled";
 			};
 

arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi

@@ -74,9 +74,10 @@ cps_eth0: eth0 {
 						     <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>;
+						     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>,
+						     <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared";
+							  "tx-cpu3", "rx-shared", "link";
 					port-id = <0>;
 					gop-port-id = <0>;
 					status = "disabled";
@@ -87,9 +88,10 @@ cps_eth1: eth1 {
 						     <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>;
+						     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>,
+						     <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared";
+							  "tx-cpu3", "rx-shared", "link";
 					port-id = <1>;
 					gop-port-id = <2>;
 					status = "disabled";
@@ -100,15 +102,54 @@ cps_eth2: eth2 {
 						     <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>,
 						     <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>;
+						     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>,
+						     <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared";
+							  "tx-cpu3", "rx-shared", "link";
 					port-id = <2>;
 					gop-port-id = <3>;
 					status = "disabled";
 				};
 			};
 
+			cps_comphy: phy@120000 {
+				compatible = "marvell,comphy-cp110";
+				reg = <0x120000 0x6000>;
+				marvell,system-controller = <&cps_syscon0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				cps_comphy0: phy@0 {
+					reg = <0>;
+					#phy-cells = <1>;
+				};
+
+				cps_comphy1: phy@1 {
+					reg = <1>;
+					#phy-cells = <1>;
+				};
+
+				cps_comphy2: phy@2 {
+					reg = <2>;
+					#phy-cells = <1>;
+				};
+
+				cps_comphy3: phy@3 {
+					reg = <3>;
+					#phy-cells = <1>;
+				};
+
+				cps_comphy4: phy@4 {
+					reg = <4>;
+					#phy-cells = <1>;
+				};
+
+				cps_comphy5: phy@5 {
+					reg = <5>;
+					#phy-cells = <1>;
+				};
+			};
+
 			cps_mdio: mdio@12a200 {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -143,7 +184,7 @@ cps_rtc: rtc@284000 {
 
 			cps_syscon0: system-controller@440000 {
 				compatible = "syscon", "simple-mfd";
-				reg = <0x440000 0x1000>;
+				reg = <0x440000 0x2000>;
 
 				cps_clk: clock {
 					compatible = "marvell,cp110-clock";
@@ -275,7 +316,8 @@ cps_nand: nand@720000 {
 				 * this controller is only usable on the CPM
 				 * for A7K and on the CPS for A8K.
 				 */
-				compatible = "marvell,armada370-nand";
+				compatible = "marvell,armada370-nand",
+					     "marvell,armada370-nand";
 				reg = <0x720000 0x54>;
 				#address-cells = <1>;
 				#size-cells = <1>;