Commit b3e5838a authored by Linus Torvalds's avatar Linus Torvalds

Merge branch 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata fixes from Tejun Heo:
 "Rather big for fixes pull.

   - SCC controllers never lived to see the light of the day.  Both
     libata and ide drivers removed.

   - In some configurations, link power management policy changes
     sometimes cause delayed spurious PHY events which can develop into
     noticeable failures.  This has been reported several times over the
     years.  Gabriele's patches suppress PHY events for a while after
     LPM policy changes which should help most of these failures without
     causing too much problem for hotplug use cases.

   - A few controller specific fixes"

[ Hmm.  I don't think removing SSC support is really a "fix", but hey, it
  removes a lot of lines of code.  Which I like.  So ...  good riddance ]

* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: avoton port-disable reset-quirk
  ata: select DW_DMAC in case of SATA_DWC
  libata: Blacklist queued TRIM on all Samsung 800-series
  libata: Ignore spurious PHY event on LPM policy change
  libata: Add helper to determine when PHY events should be ignored
  ata: ahci_st: fixup layering violations / drvdata errors
  Remove celleb-only SCC PATA drivers
parents c91aa67e dbfe8ef5
...@@ -270,6 +270,7 @@ config ATA_PIIX ...@@ -270,6 +270,7 @@ config ATA_PIIX
config SATA_DWC config SATA_DWC
tristate "DesignWare Cores SATA support" tristate "DesignWare Cores SATA support"
depends on 460EX depends on 460EX
select DW_DMAC
help help
This option enables support for the on-chip SATA controller of the This option enables support for the on-chip SATA controller of the
AppliedMicro processor 460EX. AppliedMicro processor 460EX.
...@@ -729,15 +730,6 @@ config PATA_SC1200 ...@@ -729,15 +730,6 @@ config PATA_SC1200
If unsure, say N. If unsure, say N.
config PATA_SCC
tristate "Toshiba's Cell Reference Set IDE support"
depends on PCI && PPC_CELLEB
help
This option enables support for the built-in IDE controller on
Toshiba Cell Reference Board.
If unsure, say N.
config PATA_SCH config PATA_SCH
tristate "Intel SCH PATA support" tristate "Intel SCH PATA support"
depends on PCI depends on PCI
......
...@@ -75,7 +75,6 @@ obj-$(CONFIG_PATA_PDC_OLD) += pata_pdc202xx_old.o ...@@ -75,7 +75,6 @@ obj-$(CONFIG_PATA_PDC_OLD) += pata_pdc202xx_old.o
obj-$(CONFIG_PATA_RADISYS) += pata_radisys.o obj-$(CONFIG_PATA_RADISYS) += pata_radisys.o
obj-$(CONFIG_PATA_RDC) += pata_rdc.o obj-$(CONFIG_PATA_RDC) += pata_rdc.o
obj-$(CONFIG_PATA_SC1200) += pata_sc1200.o obj-$(CONFIG_PATA_SC1200) += pata_sc1200.o
obj-$(CONFIG_PATA_SCC) += pata_scc.o
obj-$(CONFIG_PATA_SCH) += pata_sch.o obj-$(CONFIG_PATA_SCH) += pata_sch.o
obj-$(CONFIG_PATA_SERVERWORKS) += pata_serverworks.o obj-$(CONFIG_PATA_SERVERWORKS) += pata_serverworks.o
obj-$(CONFIG_PATA_SIL680) += pata_sil680.o obj-$(CONFIG_PATA_SIL680) += pata_sil680.o
......
...@@ -66,6 +66,7 @@ enum board_ids { ...@@ -66,6 +66,7 @@ enum board_ids {
board_ahci_yes_fbs, board_ahci_yes_fbs,
/* board IDs for specific chipsets in alphabetical order */ /* board IDs for specific chipsets in alphabetical order */
board_ahci_avn,
board_ahci_mcp65, board_ahci_mcp65,
board_ahci_mcp77, board_ahci_mcp77,
board_ahci_mcp89, board_ahci_mcp89,
...@@ -84,6 +85,8 @@ enum board_ids { ...@@ -84,6 +85,8 @@ enum board_ids {
static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class, static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline); unsigned long deadline);
static int ahci_avn_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
static void ahci_mcp89_apple_enable(struct pci_dev *pdev); static void ahci_mcp89_apple_enable(struct pci_dev *pdev);
static bool is_mcp89_apple(struct pci_dev *pdev); static bool is_mcp89_apple(struct pci_dev *pdev);
static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class, static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
...@@ -107,6 +110,11 @@ static struct ata_port_operations ahci_p5wdh_ops = { ...@@ -107,6 +110,11 @@ static struct ata_port_operations ahci_p5wdh_ops = {
.hardreset = ahci_p5wdh_hardreset, .hardreset = ahci_p5wdh_hardreset,
}; };
static struct ata_port_operations ahci_avn_ops = {
.inherits = &ahci_ops,
.hardreset = ahci_avn_hardreset,
};
static const struct ata_port_info ahci_port_info[] = { static const struct ata_port_info ahci_port_info[] = {
/* by features */ /* by features */
[board_ahci] = { [board_ahci] = {
...@@ -151,6 +159,12 @@ static const struct ata_port_info ahci_port_info[] = { ...@@ -151,6 +159,12 @@ static const struct ata_port_info ahci_port_info[] = {
.port_ops = &ahci_ops, .port_ops = &ahci_ops,
}, },
/* by chipsets */ /* by chipsets */
[board_ahci_avn] = {
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_avn_ops,
},
[board_ahci_mcp65] = { [board_ahci_mcp65] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_FPDMA_AA | AHCI_HFLAG_NO_PMP | AHCI_HFLAGS (AHCI_HFLAG_NO_FPDMA_AA | AHCI_HFLAG_NO_PMP |
AHCI_HFLAG_YES_NCQ), AHCI_HFLAG_YES_NCQ),
...@@ -290,14 +304,14 @@ static const struct pci_device_id ahci_pci_tbl[] = { ...@@ -290,14 +304,14 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, 0x1f27), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f27), board_ahci }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f2e), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f2e), board_ahci }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f2f), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f2f), board_ahci }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f32), board_ahci }, /* Avoton AHCI */ { PCI_VDEVICE(INTEL, 0x1f32), board_ahci_avn }, /* Avoton AHCI */
{ PCI_VDEVICE(INTEL, 0x1f33), board_ahci }, /* Avoton AHCI */ { PCI_VDEVICE(INTEL, 0x1f33), board_ahci_avn }, /* Avoton AHCI */
{ PCI_VDEVICE(INTEL, 0x1f34), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f34), board_ahci_avn }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f35), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f35), board_ahci_avn }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f36), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f36), board_ahci_avn }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f37), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f37), board_ahci_avn }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f3e), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f3e), board_ahci_avn }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f3f), board_ahci }, /* Avoton RAID */ { PCI_VDEVICE(INTEL, 0x1f3f), board_ahci_avn }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x2823), board_ahci }, /* Wellsburg RAID */ { PCI_VDEVICE(INTEL, 0x2823), board_ahci }, /* Wellsburg RAID */
{ PCI_VDEVICE(INTEL, 0x2827), board_ahci }, /* Wellsburg RAID */ { PCI_VDEVICE(INTEL, 0x2827), board_ahci }, /* Wellsburg RAID */
{ PCI_VDEVICE(INTEL, 0x8d02), board_ahci }, /* Wellsburg AHCI */ { PCI_VDEVICE(INTEL, 0x8d02), board_ahci }, /* Wellsburg AHCI */
...@@ -670,6 +684,79 @@ static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class, ...@@ -670,6 +684,79 @@ static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
return rc; return rc;
} }
/*
* ahci_avn_hardreset - attempt more aggressive recovery of Avoton ports.
*
* It has been observed with some SSDs that the timing of events in the
* link synchronization phase can leave the port in a state that can not
* be recovered by a SATA-hard-reset alone. The failing signature is
* SStatus.DET stuck at 1 ("Device presence detected but Phy
* communication not established"). It was found that unloading and
* reloading the driver when this problem occurs allows the drive
* connection to be recovered (DET advanced to 0x3). The critical
* component of reloading the driver is that the port state machines are
* reset by bouncing "port enable" in the AHCI PCS configuration
* register. So, reproduce that effect by bouncing a port whenever we
* see DET==1 after a reset.
*/
static int ahci_avn_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
struct ata_port *ap = link->ap;
struct ahci_port_priv *pp = ap->private_data;
struct ahci_host_priv *hpriv = ap->host->private_data;
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
unsigned long tmo = deadline - jiffies;
struct ata_taskfile tf;
bool online;
int rc, i;
DPRINTK("ENTER\n");
ahci_stop_engine(ap);
for (i = 0; i < 2; i++) {
u16 val;
u32 sstatus;
int port = ap->port_no;
struct ata_host *host = ap->host;
struct pci_dev *pdev = to_pci_dev(host->dev);
/* clear D2H reception area to properly wait for D2H FIS */
ata_tf_init(link->device, &tf);
tf.command = ATA_BUSY;
ata_tf_to_fis(&tf, 0, 0, d2h_fis);
rc = sata_link_hardreset(link, timing, deadline, &online,
ahci_check_ready);
if (sata_scr_read(link, SCR_STATUS, &sstatus) != 0 ||
(sstatus & 0xf) != 1)
break;
ata_link_printk(link, KERN_INFO, "avn bounce port%d\n",
port);
pci_read_config_word(pdev, 0x92, &val);
val &= ~(1 << port);
pci_write_config_word(pdev, 0x92, val);
ata_msleep(ap, 1000);
val |= 1 << port;
pci_write_config_word(pdev, 0x92, val);
deadline += tmo;
}
hpriv->start_engine(ap);
if (online)
*class = ahci_dev_classify(ap);
DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
return rc;
}
#ifdef CONFIG_PM #ifdef CONFIG_PM
static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg) static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{ {
......
...@@ -37,7 +37,6 @@ struct st_ahci_drv_data { ...@@ -37,7 +37,6 @@ struct st_ahci_drv_data {
struct reset_control *pwr; struct reset_control *pwr;
struct reset_control *sw_rst; struct reset_control *sw_rst;
struct reset_control *pwr_rst; struct reset_control *pwr_rst;
struct ahci_host_priv *hpriv;
}; };
static void st_ahci_configure_oob(void __iomem *mmio) static void st_ahci_configure_oob(void __iomem *mmio)
...@@ -55,9 +54,10 @@ static void st_ahci_configure_oob(void __iomem *mmio) ...@@ -55,9 +54,10 @@ static void st_ahci_configure_oob(void __iomem *mmio)
writel(new_val, mmio + ST_AHCI_OOBR); writel(new_val, mmio + ST_AHCI_OOBR);
} }
static int st_ahci_deassert_resets(struct device *dev) static int st_ahci_deassert_resets(struct ahci_host_priv *hpriv,
struct device *dev)
{ {
struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev); struct st_ahci_drv_data *drv_data = hpriv->plat_data;
int err; int err;
if (drv_data->pwr) { if (drv_data->pwr) {
...@@ -90,8 +90,8 @@ static int st_ahci_deassert_resets(struct device *dev) ...@@ -90,8 +90,8 @@ static int st_ahci_deassert_resets(struct device *dev)
static void st_ahci_host_stop(struct ata_host *host) static void st_ahci_host_stop(struct ata_host *host)
{ {
struct ahci_host_priv *hpriv = host->private_data; struct ahci_host_priv *hpriv = host->private_data;
struct st_ahci_drv_data *drv_data = hpriv->plat_data;
struct device *dev = host->dev; struct device *dev = host->dev;
struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
int err; int err;
if (drv_data->pwr) { if (drv_data->pwr) {
...@@ -103,29 +103,30 @@ static void st_ahci_host_stop(struct ata_host *host) ...@@ -103,29 +103,30 @@ static void st_ahci_host_stop(struct ata_host *host)
ahci_platform_disable_resources(hpriv); ahci_platform_disable_resources(hpriv);
} }
static int st_ahci_probe_resets(struct platform_device *pdev) static int st_ahci_probe_resets(struct ahci_host_priv *hpriv,
struct device *dev)
{ {
struct st_ahci_drv_data *drv_data = platform_get_drvdata(pdev); struct st_ahci_drv_data *drv_data = hpriv->plat_data;
drv_data->pwr = devm_reset_control_get(&pdev->dev, "pwr-dwn"); drv_data->pwr = devm_reset_control_get(dev, "pwr-dwn");
if (IS_ERR(drv_data->pwr)) { if (IS_ERR(drv_data->pwr)) {
dev_info(&pdev->dev, "power reset control not defined\n"); dev_info(dev, "power reset control not defined\n");
drv_data->pwr = NULL; drv_data->pwr = NULL;
} }
drv_data->sw_rst = devm_reset_control_get(&pdev->dev, "sw-rst"); drv_data->sw_rst = devm_reset_control_get(dev, "sw-rst");
if (IS_ERR(drv_data->sw_rst)) { if (IS_ERR(drv_data->sw_rst)) {
dev_info(&pdev->dev, "soft reset control not defined\n"); dev_info(dev, "soft reset control not defined\n");
drv_data->sw_rst = NULL; drv_data->sw_rst = NULL;
} }
drv_data->pwr_rst = devm_reset_control_get(&pdev->dev, "pwr-rst"); drv_data->pwr_rst = devm_reset_control_get(dev, "pwr-rst");
if (IS_ERR(drv_data->pwr_rst)) { if (IS_ERR(drv_data->pwr_rst)) {
dev_dbg(&pdev->dev, "power soft reset control not defined\n"); dev_dbg(dev, "power soft reset control not defined\n");
drv_data->pwr_rst = NULL; drv_data->pwr_rst = NULL;
} }
return st_ahci_deassert_resets(&pdev->dev); return st_ahci_deassert_resets(hpriv, dev);
} }
static struct ata_port_operations st_ahci_port_ops = { static struct ata_port_operations st_ahci_port_ops = {
...@@ -154,15 +155,12 @@ static int st_ahci_probe(struct platform_device *pdev) ...@@ -154,15 +155,12 @@ static int st_ahci_probe(struct platform_device *pdev)
if (!drv_data) if (!drv_data)
return -ENOMEM; return -ENOMEM;
platform_set_drvdata(pdev, drv_data);
hpriv = ahci_platform_get_resources(pdev); hpriv = ahci_platform_get_resources(pdev);
if (IS_ERR(hpriv)) if (IS_ERR(hpriv))
return PTR_ERR(hpriv); return PTR_ERR(hpriv);
hpriv->plat_data = drv_data;
drv_data->hpriv = hpriv; err = st_ahci_probe_resets(hpriv, &pdev->dev);
err = st_ahci_probe_resets(pdev);
if (err) if (err)
return err; return err;
...@@ -170,7 +168,7 @@ static int st_ahci_probe(struct platform_device *pdev) ...@@ -170,7 +168,7 @@ static int st_ahci_probe(struct platform_device *pdev)
if (err) if (err)
return err; return err;
st_ahci_configure_oob(drv_data->hpriv->mmio); st_ahci_configure_oob(hpriv->mmio);
err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info, err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info,
&ahci_platform_sht); &ahci_platform_sht);
...@@ -185,8 +183,9 @@ static int st_ahci_probe(struct platform_device *pdev) ...@@ -185,8 +183,9 @@ static int st_ahci_probe(struct platform_device *pdev)
#ifdef CONFIG_PM_SLEEP #ifdef CONFIG_PM_SLEEP
static int st_ahci_suspend(struct device *dev) static int st_ahci_suspend(struct device *dev)
{ {
struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev); struct ata_host *host = dev_get_drvdata(dev);
struct ahci_host_priv *hpriv = drv_data->hpriv; struct ahci_host_priv *hpriv = host->private_data;
struct st_ahci_drv_data *drv_data = hpriv->plat_data;
int err; int err;
err = ahci_platform_suspend_host(dev); err = ahci_platform_suspend_host(dev);
...@@ -208,21 +207,21 @@ static int st_ahci_suspend(struct device *dev) ...@@ -208,21 +207,21 @@ static int st_ahci_suspend(struct device *dev)
static int st_ahci_resume(struct device *dev) static int st_ahci_resume(struct device *dev)
{ {
struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev); struct ata_host *host = dev_get_drvdata(dev);
struct ahci_host_priv *hpriv = drv_data->hpriv; struct ahci_host_priv *hpriv = host->private_data;
int err; int err;
err = ahci_platform_enable_resources(hpriv); err = ahci_platform_enable_resources(hpriv);
if (err) if (err)
return err; return err;
err = st_ahci_deassert_resets(dev); err = st_ahci_deassert_resets(hpriv, dev);
if (err) { if (err) {
ahci_platform_disable_resources(hpriv); ahci_platform_disable_resources(hpriv);
return err; return err;
} }
st_ahci_configure_oob(drv_data->hpriv->mmio); st_ahci_configure_oob(hpriv->mmio);
return ahci_platform_resume_host(dev); return ahci_platform_resume_host(dev);
} }
......
...@@ -1707,8 +1707,7 @@ static void ahci_handle_port_interrupt(struct ata_port *ap, ...@@ -1707,8 +1707,7 @@ static void ahci_handle_port_interrupt(struct ata_port *ap,
if (unlikely(resetting)) if (unlikely(resetting))
status &= ~PORT_IRQ_BAD_PMP; status &= ~PORT_IRQ_BAD_PMP;
/* if LPM is enabled, PHYRDY doesn't mean anything */ if (sata_lpm_ignore_phy_events(&ap->link)) {
if (ap->link.lpm_policy > ATA_LPM_MAX_POWER) {
status &= ~PORT_IRQ_PHYRDY; status &= ~PORT_IRQ_PHYRDY;
ahci_scr_write(&ap->link, SCR_ERROR, SERR_PHYRDY_CHG); ahci_scr_write(&ap->link, SCR_ERROR, SERR_PHYRDY_CHG);
} }
......
...@@ -4235,7 +4235,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { ...@@ -4235,7 +4235,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
ATA_HORKAGE_ZERO_AFTER_TRIM, }, ATA_HORKAGE_ZERO_AFTER_TRIM, },
{ "Crucial_CT*MX100*", "MU01", ATA_HORKAGE_NO_NCQ_TRIM | { "Crucial_CT*MX100*", "MU01", ATA_HORKAGE_NO_NCQ_TRIM |
ATA_HORKAGE_ZERO_AFTER_TRIM, }, ATA_HORKAGE_ZERO_AFTER_TRIM, },
{ "Samsung SSD 850 PRO*", NULL, ATA_HORKAGE_NO_NCQ_TRIM | { "Samsung SSD 8*", NULL, ATA_HORKAGE_NO_NCQ_TRIM |
ATA_HORKAGE_ZERO_AFTER_TRIM, }, ATA_HORKAGE_ZERO_AFTER_TRIM, },
/* /*
...@@ -6752,6 +6752,38 @@ u32 ata_wait_register(struct ata_port *ap, void __iomem *reg, u32 mask, u32 val, ...@@ -6752,6 +6752,38 @@ u32 ata_wait_register(struct ata_port *ap, void __iomem *reg, u32 mask, u32 val,
return tmp; return tmp;
} }
/**
* sata_lpm_ignore_phy_events - test if PHY event should be ignored
* @link: Link receiving the event
*
* Test whether the received PHY event has to be ignored or not.
*
* LOCKING:
* None:
*
* RETURNS:
* True if the event has to be ignored.
*/
bool sata_lpm_ignore_phy_events(struct ata_link *link)
{
unsigned long lpm_timeout = link->last_lpm_change +
msecs_to_jiffies(ATA_TMOUT_SPURIOUS_PHY);
/* if LPM is enabled, PHYRDY doesn't mean anything */
if (link->lpm_policy > ATA_LPM_MAX_POWER)
return true;
/* ignore the first PHY event after the LPM policy changed
* as it is might be spurious
*/
if ((link->flags & ATA_LFLAG_CHANGED) &&
time_before(jiffies, lpm_timeout))
return true;
return false;
}
EXPORT_SYMBOL_GPL(sata_lpm_ignore_phy_events);
/* /*
* Dummy port_ops * Dummy port_ops
*/ */
......
...@@ -3597,6 +3597,9 @@ static int ata_eh_set_lpm(struct ata_link *link, enum ata_lpm_policy policy, ...@@ -3597,6 +3597,9 @@ static int ata_eh_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
} }
} }
link->last_lpm_change = jiffies;
link->flags |= ATA_LFLAG_CHANGED;
return 0; return 0;
fail: fail:
......
This diff is collapsed.
...@@ -643,15 +643,6 @@ config BLK_DEV_TC86C001 ...@@ -643,15 +643,6 @@ config BLK_DEV_TC86C001
help help
This driver adds support for Toshiba TC86C001 GOKU-S chip. This driver adds support for Toshiba TC86C001 GOKU-S chip.
config BLK_DEV_CELLEB
tristate "Toshiba's Cell Reference Set IDE support"
depends on PPC_CELLEB
select BLK_DEV_IDEDMA_PCI
help
This driver provides support for the on-board IDE controller on
Toshiba Cell Reference Board.
If unsure, say Y.
endif endif
# TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF # TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
......
...@@ -38,7 +38,6 @@ obj-$(CONFIG_BLK_DEV_AEC62XX) += aec62xx.o ...@@ -38,7 +38,6 @@ obj-$(CONFIG_BLK_DEV_AEC62XX) += aec62xx.o
obj-$(CONFIG_BLK_DEV_ALI15X3) += alim15x3.o obj-$(CONFIG_BLK_DEV_ALI15X3) += alim15x3.o
obj-$(CONFIG_BLK_DEV_AMD74XX) += amd74xx.o obj-$(CONFIG_BLK_DEV_AMD74XX) += amd74xx.o
obj-$(CONFIG_BLK_DEV_ATIIXP) += atiixp.o obj-$(CONFIG_BLK_DEV_ATIIXP) += atiixp.o
obj-$(CONFIG_BLK_DEV_CELLEB) += scc_pata.o
obj-$(CONFIG_BLK_DEV_CMD64X) += cmd64x.o obj-$(CONFIG_BLK_DEV_CMD64X) += cmd64x.o
obj-$(CONFIG_BLK_DEV_CS5520) += cs5520.o obj-$(CONFIG_BLK_DEV_CS5520) += cs5520.o
obj-$(CONFIG_BLK_DEV_CS5530) += cs5530.o obj-$(CONFIG_BLK_DEV_CS5530) += cs5530.o
......
This diff is collapsed.
...@@ -205,6 +205,7 @@ enum { ...@@ -205,6 +205,7 @@ enum {
ATA_LFLAG_SW_ACTIVITY = (1 << 7), /* keep activity stats */ ATA_LFLAG_SW_ACTIVITY = (1 << 7), /* keep activity stats */
ATA_LFLAG_NO_LPM = (1 << 8), /* disable LPM on this link */ ATA_LFLAG_NO_LPM = (1 << 8), /* disable LPM on this link */
ATA_LFLAG_RST_ONCE = (1 << 9), /* limit recovery to one reset */ ATA_LFLAG_RST_ONCE = (1 << 9), /* limit recovery to one reset */
ATA_LFLAG_CHANGED = (1 << 10), /* LPM state changed on this link */
/* struct ata_port flags */ /* struct ata_port flags */
ATA_FLAG_SLAVE_POSS = (1 << 0), /* host supports slave dev */ ATA_FLAG_SLAVE_POSS = (1 << 0), /* host supports slave dev */
...@@ -309,6 +310,12 @@ enum { ...@@ -309,6 +310,12 @@ enum {
*/ */
ATA_TMOUT_PMP_SRST_WAIT = 5000, ATA_TMOUT_PMP_SRST_WAIT = 5000,
/* When the LPM policy is set to ATA_LPM_MAX_POWER, there might
* be a spurious PHY event, so ignore the first PHY event that
* occurs within 10s after the policy change.
*/
ATA_TMOUT_SPURIOUS_PHY = 10000,
/* ATA bus states */ /* ATA bus states */
BUS_UNKNOWN = 0, BUS_UNKNOWN = 0,
BUS_DMA = 1, BUS_DMA = 1,
...@@ -788,6 +795,8 @@ struct ata_link { ...@@ -788,6 +795,8 @@ struct ata_link {
struct ata_eh_context eh_context; struct ata_eh_context eh_context;
struct ata_device device[ATA_MAX_DEVICES]; struct ata_device device[ATA_MAX_DEVICES];
unsigned long last_lpm_change; /* when last LPM change happened */
}; };
#define ATA_LINK_CLEAR_BEGIN offsetof(struct ata_link, active_tag) #define ATA_LINK_CLEAR_BEGIN offsetof(struct ata_link, active_tag)
#define ATA_LINK_CLEAR_END offsetof(struct ata_link, device[0]) #define ATA_LINK_CLEAR_END offsetof(struct ata_link, device[0])
...@@ -1201,6 +1210,7 @@ extern struct ata_device *ata_dev_pair(struct ata_device *adev); ...@@ -1201,6 +1210,7 @@ extern struct ata_device *ata_dev_pair(struct ata_device *adev);
extern int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev); extern int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev);
extern void ata_scsi_port_error_handler(struct Scsi_Host *host, struct ata_port *ap); extern void ata_scsi_port_error_handler(struct Scsi_Host *host, struct ata_port *ap);
extern void ata_scsi_cmd_error_handler(struct Scsi_Host *host, struct ata_port *ap, struct list_head *eh_q); extern void ata_scsi_cmd_error_handler(struct Scsi_Host *host, struct ata_port *ap, struct list_head *eh_q);
extern bool sata_lpm_ignore_phy_events(struct ata_link *link);
extern int ata_cable_40wire(struct ata_port *ap); extern int ata_cable_40wire(struct ata_port *ap);
extern int ata_cable_80wire(struct ata_port *ap); extern int ata_cable_80wire(struct ata_port *ap);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment