Commit b3f7ed03 authored by Rob Herring's avatar Rob Herring Committed by Arnd Bergmann

ARM: gic: add OF based initialization

This adds ARM gic interrupt controller initialization using device tree
data.

The initialization function is intended to be called by of_irq_init
function like this:

const static struct of_device_id irq_match[] = {
	{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
	{}
};

static void __init init_irqs(void)
{
	of_irq_init(irq_match);
}
Signed-off-by: default avatarRob Herring <rob.herring@calxeda.com>
Reviewed-by: default avatarJamie Iles <jamie@jamieiles.com>
Tested-by: default avatarThomas Abraham <thomas.abraham@linaro.org>
Acked-by: default avatarGrant Likely <grant.likely@secretlab.ca>
parent 4294f8ba
* ARM Generic Interrupt Controller
ARM SMP cores are often associated with a GIC, providing per processor
interrupts (PPI), shared processor interrupts (SPI) and software
generated interrupts (SGI).
Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
Secondary GICs are cascaded into the upward interrupt controller and do not
have PPIs or SGIs.
Main node required properties:
- compatible : should be one of:
"arm,cortex-a9-gic"
"arm,arm11mp-gic"
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Specifies the number of cells needed to encode an
interrupt source. The type shall be a <u32> and the value shall be 3.
The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
interrupts.
The 2nd cell contains the interrupt number for the interrupt type.
SPI interrupts are in the range [0-987]. PPI interrupts are in the
range [0-15].
The 3rd cell is the flags, encoded as follows:
bits[3:0] trigger type and level flags.
1 = low-to-high edge triggered
2 = high-to-low edge triggered
4 = active high level-sensitive
8 = active low level-sensitive
bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of
the 8 possible cpus attached to the GIC. A bit set to '1' indicated
the interrupt is wired to that CPU. Only valid for PPI interrupts.
- reg : Specifies base physical address(s) and size of the GIC registers. The
first region is the GIC distributor register base and size. The 2nd region is
the GIC cpu interface register base and size.
Optional
- interrupts : Interrupt source of the parent interrupt controller. Only
present on secondary GICs.
Example:
intc: interrupt-controller@fff11000 {
compatible = "arm,cortex-a9-gic";
#interrupt-cells = <3>;
#address-cells = <1>;
interrupt-controller;
reg = <0xfff11000 0x1000>,
<0xfff10100 0x100>;
};
......@@ -30,6 +30,9 @@
#include <linux/cpu_pm.h>
#include <linux/cpumask.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/irqdomain.h>
#include <linux/interrupt.h>
#include <linux/percpu.h>
......@@ -530,7 +533,33 @@ static void __init gic_pm_init(struct gic_chip_data *gic)
}
#endif
#ifdef CONFIG_OF
static int gic_irq_domain_dt_translate(struct irq_domain *d,
struct device_node *controller,
const u32 *intspec, unsigned int intsize,
unsigned long *out_hwirq, unsigned int *out_type)
{
if (d->of_node != controller)
return -EINVAL;
if (intsize < 3)
return -EINVAL;
/* Get the interrupt number and add 16 to skip over SGIs */
*out_hwirq = intspec[1] + 16;
/* For SPIs, we need to add 16 more to get the GIC irq ID number */
if (!intspec[0])
*out_hwirq += 16;
*out_type = intspec[2] & IRQ_TYPE_SENSE_MASK;
return 0;
}
#endif
const struct irq_domain_ops gic_irq_domain_ops = {
#ifdef CONFIG_OF
.dt_translate = gic_irq_domain_dt_translate,
#endif
};
void __init gic_init(unsigned int gic_nr, unsigned int irq_start,
......@@ -608,3 +637,35 @@ void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
writel_relaxed(map << 16 | irq, gic_data[0].dist_base + GIC_DIST_SOFTINT);
}
#endif
#ifdef CONFIG_OF
static int gic_cnt __initdata = 0;
int __init gic_of_init(struct device_node *node, struct device_node *parent)
{
void __iomem *cpu_base;
void __iomem *dist_base;
int irq;
struct irq_domain *domain = &gic_data[gic_cnt].domain;
if (WARN_ON(!node))
return -ENODEV;
dist_base = of_iomap(node, 0);
WARN(!dist_base, "unable to map gic dist registers\n");
cpu_base = of_iomap(node, 1);
WARN(!cpu_base, "unable to map gic cpu registers\n");
domain->of_node = of_node_get(node);
gic_init(gic_cnt, 16, dist_base, cpu_base);
if (parent) {
irq = irq_of_parse_and_map(node, 0);
gic_cascade_irq(gic_cnt, irq);
}
gic_cnt++;
return 0;
}
#endif
......@@ -40,6 +40,7 @@ extern void __iomem *gic_cpu_base_addr;
extern struct irq_chip gic_arch_extn;
void gic_init(unsigned int, unsigned int, void __iomem *, void __iomem *);
int gic_of_init(struct device_node *node, struct device_node *parent);
void gic_secondary_init(unsigned int);
void gic_cascade_irq(unsigned int gic_nr, unsigned int irq);
void gic_raise_softirq(const struct cpumask *mask, unsigned int irq);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment