power: supply: smb347-charger: Drop pdata support

There are no platforms using the pdata support, so let's
drop it to simplify the driver.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

include/linux/power/smb347-charger.h

-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Summit Microelectronics SMB347 Battery Charger Driver
- *
- * Copyright (C) 2011, Intel Corporation
- *
- * Authors: Bruce E. Robertson <bruce.e.robertson@intel.com>
- *          Mika Westerberg <mika.westerberg@linux.intel.com>
- */
-
-#ifndef SMB347_CHARGER_H
-#define SMB347_CHARGER_H
-
-#include <linux/types.h>
-#include <linux/power_supply.h>
-
-enum {
-	/* use the default compensation method */
-	SMB347_SOFT_TEMP_COMPENSATE_DEFAULT = -1,
-
-	SMB347_SOFT_TEMP_COMPENSATE_NONE,
-	SMB347_SOFT_TEMP_COMPENSATE_CURRENT,
-	SMB347_SOFT_TEMP_COMPENSATE_VOLTAGE,
-};
-
-/* Use default factory programmed value for hard/soft temperature limit */
-#define SMB347_TEMP_USE_DEFAULT		-273
-
-/*
- * Charging enable can be controlled by software (via i2c) by
- * smb347-charger driver or by EN pin (active low/high).
- */
-enum smb347_chg_enable {
-	SMB347_CHG_ENABLE_SW,
-	SMB347_CHG_ENABLE_PIN_ACTIVE_LOW,
-	SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH,
-};
-
-/**
- * struct smb347_charger_platform_data - platform data for SMB347 charger
- * @battery_info: Information about the battery
- * @max_charge_current: maximum current (in uA) the battery can be charged
- * @max_charge_voltage: maximum voltage (in uV) the battery can be charged
- * @pre_charge_current: current (in uA) to use in pre-charging phase
- * @termination_current: current (in uA) used to determine when the
- *			 charging cycle terminates
- * @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to
- *			 pre-charge to fast charge mode
- * @mains_current_limit: maximum input current drawn from AC/DC input (in uA)
- * @usb_hc_current_limit: maximum input high current (in uA) drawn from USB
- *			  input
- * @chip_temp_threshold: die temperature where device starts limiting charge
- *			 current [%100 - %130] (in degree C)
- * @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C),
- *			  granularity is 5 deg C.
- * @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree  C),
- *			 granularity is 5 deg C.
- * @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C),
- *			  granularity is 5 deg C.
- * @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C),
- *			 granularity is 5 deg C.
- * @suspend_on_hard_temp_limit: suspend charging when hard limit is hit
- * @soft_temp_limit_compensation: compensation method when soft temperature
- *				  limit is hit
- * @charge_current_compensation: current (in uA) for charging compensation
- *				 current when temperature hits soft limits
- * @use_mains: AC/DC input can be used
- * @use_usb: USB input can be used
- * @use_usb_otg: USB OTG output can be used (not implemented yet)
- * @irq_gpio: GPIO number used for interrupts (%-1 if not used)
- * @enable_control: how charging enable/disable is controlled
- *		    (driver/pin controls)
- *
- * @use_main, @use_usb, and @use_usb_otg are means to enable/disable
- * hardware support for these. This is useful when we want to have for
- * example OTG charging controlled via OTG transceiver driver and not by
- * the SMB347 hardware.
- *
- * Hard and soft temperature limit values are given as described in the
- * device data sheet and assuming NTC beta value is %3750. Even if this is
- * not the case, these values should be used. They can be mapped to the
- * corresponding NTC beta values with the help of table %2 in the data
- * sheet. So for example if NTC beta is %3375 and we want to program hard
- * hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50.
- *
- * If zero value is given in any of the current and voltage values, the
- * factory programmed default will be used. For soft/hard temperature
- * values, pass in %SMB347_TEMP_USE_DEFAULT instead.
- */
-struct smb347_charger_platform_data {
-	struct power_supply_info battery_info;
-	unsigned int	max_charge_current;
-	unsigned int	max_charge_voltage;
-	unsigned int	pre_charge_current;
-	unsigned int	termination_current;
-	unsigned int	pre_to_fast_voltage;
-	unsigned int	mains_current_limit;
-	unsigned int	usb_hc_current_limit;
-	unsigned int	chip_temp_threshold;
-	int		soft_cold_temp_limit;
-	int		soft_hot_temp_limit;
-	int		hard_cold_temp_limit;
-	int		hard_hot_temp_limit;
-	bool		suspend_on_hard_temp_limit;
-	unsigned int	soft_temp_limit_compensation;
-	unsigned int	charge_current_compensation;
-	bool		use_mains;
-	bool		use_usb;
-	bool		use_usb_otg;
-	int		irq_gpio;
-	enum smb347_chg_enable enable_control;
-};
-
-#endif /* SMB347_CHARGER_H */