drm: Add Panel Self Refresh DP addresses

Add the addresses and definitions I care about for Panel Self Refresh, as
documented in the eDP spec.

I'm sending these out before some other patches because this should be a fairly
simple one to get upstream and not require too much fuss (where the others may
have some fuss).

This file is a mess with white spacing. I tried to stay consistent with the
surrounding code.

v2: had some silly mistakes in v1 which Keith caught

Cc: Dave Airlie <airlied@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>

include/drm/drm_dp_helper.h

@@ -74,6 +74,20 @@
 
 #define DP_TRAINING_AUX_RD_INTERVAL         0x00e
 
+#define DP_PSR_SUPPORT                      0x070
+# define DP_PSR_IS_SUPPORTED                1
+#define DP_PSR_CAPS                         0x071
+# define DP_PSR_NO_TRAIN_ON_EXIT            1
+# define DP_PSR_SETUP_TIME_330              (0 << 1)
+# define DP_PSR_SETUP_TIME_275              (1 << 1)
+# define DP_PSR_SETUP_TIME_220              (2 << 1)
+# define DP_PSR_SETUP_TIME_165              (3 << 1)
+# define DP_PSR_SETUP_TIME_110              (4 << 1)
+# define DP_PSR_SETUP_TIME_55               (5 << 1)
+# define DP_PSR_SETUP_TIME_0                (6 << 1)
+# define DP_PSR_SETUP_TIME_MASK             (7 << 1)
+# define DP_PSR_SETUP_TIME_SHIFT            1
+
 /* link configuration */
 #define	DP_LINK_BW_SET		            0x100
 # define DP_LINK_BW_1_62		    0x06
@@ -133,6 +147,12 @@
 #define DP_MAIN_LINK_CHANNEL_CODING_SET	    0x108
 # define DP_SET_ANSI_8B10B		    (1 << 0)
 
+#define DP_PSR_EN_CFG			    0x170
+# define DP_PSR_ENABLE			    (1 << 0)
+# define DP_PSR_MAIN_LINK_ACTIVE	    (1 << 1)
+# define DP_PSR_CRC_VERIFICATION	    (1 << 2)
+# define DP_PSR_FRAME_CAPTURE		    (1 << 3)
+
 #define DP_LANE0_1_STATUS		    0x202
 #define DP_LANE2_3_STATUS		    0x203
 # define DP_LANE_CR_DONE		    (1 << 0)
@@ -169,6 +189,22 @@
 # define DP_SET_POWER_D0                    0x1
 # define DP_SET_POWER_D3                    0x2
 
+#define DP_PSR_ERROR_STATUS                 0x2006
+# define DP_PSR_LINK_CRC_ERROR              (1 << 0)
+# define DP_PSR_RFB_STORAGE_ERROR           (1 << 1)
+
+#define DP_PSR_ESI                          0x2007
+# define DP_PSR_CAPS_CHANGE                 (1 << 0)
+
+#define DP_PSR_STATUS                       0x2008
+# define DP_PSR_SINK_INACTIVE               0
+# define DP_PSR_SINK_ACTIVE_SRC_SYNCED      1
+# define DP_PSR_SINK_ACTIVE_RFB             2
+# define DP_PSR_SINK_ACTIVE_SINK_SYNCED     3
+# define DP_PSR_SINK_ACTIVE_RESYNC          4
+# define DP_PSR_SINK_INTERNAL_ERROR         7
+# define DP_PSR_SINK_STATE_MASK             0x07
+
 #define MODE_I2C_START	1
 #define MODE_I2C_WRITE	2
 #define MODE_I2C_READ	4