Merge branch 'for-torvalds' of...

Merge branch 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson

* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  mach-ux500: configure board for the TPS61052 regulator v2
  mach-ux500: provide ab8500 init vector
  mach-ux500: board support for AB8500 GPIO driver
  gpio: driver for 42 AB8500 GPIO pins

arch/arm/mach-ux500/Kconfig

@@ -23,6 +23,7 @@ menu "Ux500 target platform"
 config MACH_U8500
 	bool "U8500 Development platform"
 	depends on UX500_SOC_DB8500
+	select TPS6105X
 	help
 	  Include support for the mop500 development platform.
 

arch/arm/mach-ux500/board-mop500-regulators.c

@@ -13,6 +13,30 @@
 #include <linux/regulator/ab8500.h>
 #include "board-mop500-regulators.h"
 
+/*
+ * TPS61052 regulator
+ */
+static struct regulator_consumer_supply tps61052_vaudio_consumers[] = {
+	/*
+	 * Boost converter supply to raise voltage on audio speaker, this
+	 * is actually connected to three pins, VInVhfL (left amplifier)
+	 * VInVhfR (right amplifier) and VIntDClassInt - all three must
+	 * be connected to the same voltage.
+	 */
+	REGULATOR_SUPPLY("vintdclassint", "ab8500-codec.0"),
+};
+
+struct regulator_init_data tps61052_regulator = {
+	.constraints = {
+		.name = "vaudio-hf",
+		.min_uV = 4500000,
+		.max_uV = 4500000,
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(tps61052_vaudio_consumers),
+	.consumer_supplies = tps61052_vaudio_consumers,
+};
+
 static struct regulator_consumer_supply ab8500_vaux1_consumers[] = {
 	/* External displays, connector on board 2v5 power supply */
 	REGULATOR_SUPPLY("vaux12v5", "mcde.0"),
@@ -62,6 +86,182 @@ static struct regulator_consumer_supply ab8500_vana_consumers[] = {
 	REGULATOR_SUPPLY("vsmps2", "mcde.0"),
 };
 
+/* ab8500 regulator register initialization */
+struct ab8500_regulator_reg_init
+ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
+	/*
+	 * VanaRequestCtrl          = HP/LP depending on VxRequest
+	 * VextSupply1RequestCtrl   = HP/LP depending on VxRequest
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL2, 0x00),
+	/*
+	 * VextSupply2RequestCtrl   = HP/LP depending on VxRequest
+	 * VextSupply3RequestCtrl   = HP/LP depending on VxRequest
+	 * Vaux1RequestCtrl         = HP/LP depending on VxRequest
+	 * Vaux2RequestCtrl         = HP/LP depending on VxRequest
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL3, 0x00),
+	/*
+	 * Vaux3RequestCtrl         = HP/LP depending on VxRequest
+	 * SwHPReq                  = Control through SWValid disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL4, 0x00),
+	/*
+	 * VanaSysClkReq1HPValid    = disabled
+	 * Vaux1SysClkReq1HPValid   = disabled
+	 * Vaux2SysClkReq1HPValid   = disabled
+	 * Vaux3SysClkReq1HPValid   = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID1, 0x00),
+	/*
+	 * VextSupply1SysClkReq1HPValid = disabled
+	 * VextSupply2SysClkReq1HPValid = disabled
+	 * VextSupply3SysClkReq1HPValid = SysClkReq1 controlled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID2, 0x40),
+	/*
+	 * VanaHwHPReq1Valid        = disabled
+	 * Vaux1HwHPreq1Valid       = disabled
+	 * Vaux2HwHPReq1Valid       = disabled
+	 * Vaux3HwHPReqValid        = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID1, 0x00),
+	/*
+	 * VextSupply1HwHPReq1Valid = disabled
+	 * VextSupply2HwHPReq1Valid = disabled
+	 * VextSupply3HwHPReq1Valid = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID2, 0x00),
+	/*
+	 * VanaHwHPReq2Valid        = disabled
+	 * Vaux1HwHPReq2Valid       = disabled
+	 * Vaux2HwHPReq2Valid       = disabled
+	 * Vaux3HwHPReq2Valid       = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID1, 0x00),
+	/*
+	 * VextSupply1HwHPReq2Valid = disabled
+	 * VextSupply2HwHPReq2Valid = disabled
+	 * VextSupply3HwHPReq2Valid = HWReq2 controlled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID2, 0x04),
+	/*
+	 * VanaSwHPReqValid         = disabled
+	 * Vaux1SwHPReqValid        = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID1, 0x00),
+	/*
+	 * Vaux2SwHPReqValid        = disabled
+	 * Vaux3SwHPReqValid        = disabled
+	 * VextSupply1SwHPReqValid  = disabled
+	 * VextSupply2SwHPReqValid  = disabled
+	 * VextSupply3SwHPReqValid  = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID2, 0x00),
+	/*
+	 * SysClkReq2Valid1         = SysClkReq2 controlled
+	 * SysClkReq3Valid1         = disabled
+	 * SysClkReq4Valid1         = SysClkReq4 controlled
+	 * SysClkReq5Valid1         = disabled
+	 * SysClkReq6Valid1         = SysClkReq6 controlled
+	 * SysClkReq7Valid1         = disabled
+	 * SysClkReq8Valid1         = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID1, 0x2a),
+	/*
+	 * SysClkReq2Valid2         = disabled
+	 * SysClkReq3Valid2         = disabled
+	 * SysClkReq4Valid2         = disabled
+	 * SysClkReq5Valid2         = disabled
+	 * SysClkReq6Valid2         = SysClkReq6 controlled
+	 * SysClkReq7Valid2         = disabled
+	 * SysClkReq8Valid2         = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID2, 0x20),
+	/*
+	 * VTVoutEna                = disabled
+	 * Vintcore12Ena            = disabled
+	 * Vintcore12Sel            = 1.25 V
+	 * Vintcore12LP             = inactive (HP)
+	 * VTVoutLP                 = inactive (HP)
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUMISC1, 0x10),
+	/*
+	 * VaudioEna                = disabled
+	 * VdmicEna                 = disabled
+	 * Vamic1Ena                = disabled
+	 * Vamic2Ena                = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VAUDIOSUPPLY, 0x00),
+	/*
+	 * Vamic1_dzout             = high-Z when Vamic1 is disabled
+	 * Vamic2_dzout             = high-Z when Vamic2 is disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUCTRL1VAMIC, 0x00),
+	/*
+	 * VPll                     = Hw controlled
+	 * VanaRegu                 = force off
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VPLLVANAREGU, 0x02),
+	/*
+	 * VrefDDREna               = disabled
+	 * VrefDDRSleepMode         = inactive (no pulldown)
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VREFDDR, 0x00),
+	/*
+	 * VextSupply1Regu          = HW control
+	 * VextSupply2Regu          = HW control
+	 * VextSupply3Regu          = HW control
+	 * ExtSupply2Bypass         = ExtSupply12LPn ball is 0 when Ena is 0
+	 * ExtSupply3Bypass         = ExtSupply3LPn ball is 0 when Ena is 0
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU, 0x2a),
+	/*
+	 * Vaux1Regu                = force HP
+	 * Vaux2Regu                = force off
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VAUX12REGU, 0x01),
+	/*
+	 * Vaux3regu                = force off
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3REGU, 0x00),
+	/*
+	 * Vsmps1                   = 1.15V
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VSMPS1SEL1, 0x24),
+	/*
+	 * Vaux1Sel                 = 2.5 V
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VAUX1SEL, 0x08),
+	/*
+	 * Vaux2Sel                 = 2.9 V
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VAUX2SEL, 0x0d),
+	/*
+	 * Vaux3Sel                 = 2.91 V
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3SEL, 0x07),
+	/*
+	 * VextSupply12LP           = disabled (no LP)
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUCTRL2SPARE, 0x00),
+	/*
+	 * Vaux1Disch               = short discharge time
+	 * Vaux2Disch               = short discharge time
+	 * Vaux3Disch               = short discharge time
+	 * Vintcore12Disch          = short discharge time
+	 * VTVoutDisch              = short discharge time
+	 * VaudioDisch              = short discharge time
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH, 0x00),
+	/*
+	 * VanaDisch                = short discharge time
+	 * VdmicPullDownEna         = pulldown disabled when Vdmic is disabled
+	 * VdmicDisch               = short discharge time
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH2, 0x00),
+};
+
 /* AB8500 regulators */
 struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
 	/* supplies to the display/camera */
@@ -72,6 +272,7 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
 			.max_uV = 2900000,
 			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
 					  REGULATOR_CHANGE_STATUS,
+			.boot_on = 1, /* must be on for display */
 		},
 		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaux1_consumers),
 		.consumer_supplies = ab8500_vaux1_consumers,

arch/arm/mach-ux500/board-mop500-regulators.h

@@ -17,5 +17,6 @@
 extern struct ab8500_regulator_reg_init
 ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS];
 extern struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS];
+extern struct regulator_init_data tps61052_regulator;
 
 #endif

arch/arm/mach-ux500/board-mop500.c

@@ -22,6 +22,8 @@
 #include <linux/mfd/ab8500.h>
 #include <linux/regulator/ab8500.h>
 #include <linux/mfd/tc3589x.h>
+#include <linux/mfd/tps6105x.h>
+#include <linux/mfd/ab8500/gpio.h>
 #include <linux/leds-lp5521.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
@@ -42,10 +44,35 @@
 #include "board-mop500.h"
 #include "board-mop500-regulators.h"
 
+static struct ab8500_gpio_platform_data ab8500_gpio_pdata = {
+	.gpio_base		= MOP500_AB8500_GPIO(0),
+	.irq_base		= MOP500_AB8500_VIR_GPIO_IRQ_BASE,
+	/* config_reg is the initial configuration of ab8500 pins.
+	 * The pins can be configured as GPIO or alt functions based
+	 * on value present in GpioSel1 to GpioSel6 and AlternatFunction
+	 * register. This is the array of 7 configuration settings.
+	 * One has to compile time decide these settings. Below is the
+	 * explaination of these setting
+	 * GpioSel1 = 0x00 => Pins GPIO1 to GPIO8 are not used as GPIO
+	 * GpioSel2 = 0x1E => Pins GPIO10 to GPIO13 are configured as GPIO
+	 * GpioSel3 = 0x80 => Pin GPIO24 is configured as GPIO
+	 * GpioSel4 = 0x01 => Pin GPIo25 is configured as GPIO
+	 * GpioSel5 = 0x7A => Pins GPIO34, GPIO36 to GPIO39 are conf as GPIO
+	 * GpioSel6 = 0x00 => Pins GPIO41 & GPIo42 are not configured as GPIO
+	 * AlternaFunction = 0x00 => If Pins GPIO10 to 13 are not configured
+	 * as GPIO then this register selectes the alternate fucntions
+	 */
+	.config_reg		= {0x00, 0x1E, 0x80, 0x01,
+					0x7A, 0x00, 0x00},
+};
+
 static struct ab8500_platform_data ab8500_platdata = {
 	.irq_base	= MOP500_AB8500_IRQ_BASE,
+	.regulator_reg_init = ab8500_regulator_reg_init,
+	.num_regulator_reg_init	= ARRAY_SIZE(ab8500_regulator_reg_init),
 	.regulator	= ab8500_regulators,
 	.num_regulator	= ARRAY_SIZE(ab8500_regulators),
+	.gpio		= &ab8500_gpio_pdata,
 };
 
 static struct resource ab8500_resources[] = {
@@ -66,6 +93,15 @@ struct platform_device ab8500_device = {
 	.resource = ab8500_resources,
 };
 
+/*
+ * TPS61052
+ */
+
+static struct tps6105x_platform_data mop500_tps61052_data = {
+	.mode = TPS6105X_MODE_VOLTAGE,
+	.regulator_data = &tps61052_regulator,
+};
+
 /*
  * TC35892
  */
@@ -136,7 +172,7 @@ static struct lp5521_platform_data __initdata lp5521_sec_data = {
        .clock_mode     = LP5521_CLOCK_EXT,
 };
 
-static struct i2c_board_info mop500_i2c0_devices[] = {
+static struct i2c_board_info __initdata mop500_i2c0_devices[] = {
 	{
 		I2C_BOARD_INFO("tc3589x", 0x42),
 		.irq		= NOMADIK_GPIO_TO_IRQ(217),
@@ -144,6 +180,14 @@ static struct i2c_board_info mop500_i2c0_devices[] = {
 	},
 };
 
+/* I2C0 devices only available prior to HREFv60 */
+static struct i2c_board_info __initdata mop500_i2c0_old_devices[] = {
+	{
+		I2C_BOARD_INFO("tps61052", 0x33),
+		.platform_data  = &mop500_tps61052_data,
+	},
+};
+
 static struct i2c_board_info __initdata mop500_i2c2_devices[] = {
 	{
 		/* lp5521 LED driver, 1st device */
@@ -406,6 +450,9 @@ static void __init mop500_init_machine(void)
 
 	i2c_register_board_info(0, mop500_i2c0_devices,
 				ARRAY_SIZE(mop500_i2c0_devices));
+	if (!machine_is_hrefv60())
+		i2c_register_board_info(0, mop500_i2c0_old_devices,
+					ARRAY_SIZE(mop500_i2c0_old_devices));
 	i2c_register_board_info(2, mop500_i2c2_devices,
 				ARRAY_SIZE(mop500_i2c2_devices));
 }

arch/arm/mach-ux500/board-mop500.h

@@ -27,6 +27,10 @@
 #define GPIO_BU21013_CS			MOP500_EGPIO(13)
 #define GPIO_SDMMC_EN			MOP500_EGPIO(17)
 #define GPIO_SDMMC_1V8_3V_SEL		MOP500_EGPIO(18)
+#define MOP500_EGPIO_END		MOP500_EGPIO(24)
+
+/* GPIOs on the AB8500 mixed-signals circuit */
+#define MOP500_AB8500_GPIO(x)		(MOP500_EGPIO_END + (x))
 
 struct i2c_board_info;
 

arch/arm/mach-ux500/include/mach/irqs-board-mop500.h

@@ -35,9 +35,20 @@
 #define MOP500_STMPE1601_IRQBASE        MOP500_EGPIO_IRQ_END
 #define MOP500_STMPE1601_IRQ(x)         (MOP500_STMPE1601_IRQBASE + (x))
 
-#define MOP500_NR_IRQS          MOP500_STMPE1601_IRQ(STMPE_NR_INTERNAL_IRQS)
+#define MOP500_STMPE1601_IRQ_END	\
+	MOP500_STMPE1601_IRQ(STMPE_NR_INTERNAL_IRQS)
 
-#define MOP500_IRQ_END          MOP500_NR_IRQS
+/* AB8500 virtual gpio IRQ */
+#define AB8500_VIR_GPIO_NR_IRQS			16
+
+#define MOP500_AB8500_VIR_GPIO_IRQ_BASE		\
+	MOP500_STMPE1601_IRQ_END
+#define MOP500_AB8500_VIR_GPIO_IRQ_END		\
+	(MOP500_AB8500_VIR_GPIO_IRQ_BASE + AB8500_VIR_GPIO_NR_IRQS)
+
+#define MOP500_NR_IRQS		MOP500_AB8500_VIR_GPIO_IRQ_END
+
+#define MOP500_IRQ_END		MOP500_NR_IRQS
 
 #if MOP500_IRQ_END > IRQ_BOARD_END
 #undef IRQ_BOARD_END

drivers/gpio/Kconfig

@@ -414,4 +414,9 @@ config GPIO_JANZ_TTL
 	  This driver provides support for driving the pins in output
 	  mode only. Input mode is not supported.
 
+config AB8500_GPIO
+	bool "ST-Ericsson AB8500 Mixed Signal Circuit gpio functions"
+	depends on AB8500_CORE
+	help
+	  Select this to enable the AB8500 IC GPIO driver
 endif

drivers/gpio/Makefile

@@ -42,3 +42,4 @@ obj-$(CONFIG_GPIO_JANZ_TTL)	+= janz-ttl.o
 obj-$(CONFIG_GPIO_SX150X)	+= sx150x.o
 obj-$(CONFIG_GPIO_VX855)	+= vx855_gpio.o
 obj-$(CONFIG_GPIO_ML_IOH)	+= ml_ioh_gpio.o
+obj-$(CONFIG_AB8500_GPIO)       += ab8500-gpio.o

drivers/mfd/ab8500-core.c

@@ -362,6 +362,15 @@ static void ab8500_irq_remove(struct ab8500 *ab8500)
 	}
 }
 
+static struct resource ab8500_gpio_resources[] = {
+	{
+		.name	= "GPIO_INT6",
+		.start	= AB8500_INT_GPIO6R,
+		.end	= AB8500_INT_GPIO41F,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
 static struct resource ab8500_gpadc_resources[] = {
 	{
 		.name	= "HW_CONV_END",
@@ -595,6 +604,11 @@ static struct mfd_cell ab8500_devs[] = {
 	{
 		.name = "ab8500-regulator",
 	},
+	{
+		.name = "ab8500-gpio",
+		.num_resources = ARRAY_SIZE(ab8500_gpio_resources),
+		.resources = ab8500_gpio_resources,
+	},
 	{
 		.name = "ab8500-gpadc",
 		.num_resources = ARRAY_SIZE(ab8500_gpadc_resources),

drivers/mfd/ab8500-i2c.c

@@ -97,7 +97,7 @@ static void __exit ab8500_i2c_exit(void)
 {
 	platform_driver_unregister(&ab8500_i2c_driver);
 }
-subsys_initcall(ab8500_i2c_init);
+arch_initcall(ab8500_i2c_init);
 module_exit(ab8500_i2c_exit);
 
 MODULE_AUTHOR("Mattias WALLIN <mattias.wallin@stericsson.com");

include/linux/mfd/ab8500.h

@@ -74,6 +74,45 @@
 #define AB8500_INT_ACC_DETECT_21DB_F	37
 #define AB8500_INT_ACC_DETECT_21DB_R	38
 #define AB8500_INT_GP_SW_ADC_CONV_END	39
+#define AB8500_INT_ACC_DETECT_1DB_F	33
+#define AB8500_INT_ACC_DETECT_1DB_R	34
+#define AB8500_INT_ACC_DETECT_22DB_F	35
+#define AB8500_INT_ACC_DETECT_22DB_R	36
+#define AB8500_INT_ACC_DETECT_21DB_F	37
+#define AB8500_INT_ACC_DETECT_21DB_R	38
+#define AB8500_INT_GP_SW_ADC_CONV_END	39
+#define AB8500_INT_GPIO6R		40
+#define AB8500_INT_GPIO7R		41
+#define AB8500_INT_GPIO8R		42
+#define AB8500_INT_GPIO9R		43
+#define AB8500_INT_GPIO10R		44
+#define AB8500_INT_GPIO11R		45
+#define AB8500_INT_GPIO12R		46
+#define AB8500_INT_GPIO13R		47
+#define AB8500_INT_GPIO24R		48
+#define AB8500_INT_GPIO25R		49
+#define AB8500_INT_GPIO36R		50
+#define AB8500_INT_GPIO37R		51
+#define AB8500_INT_GPIO38R		52
+#define AB8500_INT_GPIO39R		53
+#define AB8500_INT_GPIO40R		54
+#define AB8500_INT_GPIO41R		55
+#define AB8500_INT_GPIO6F		56
+#define AB8500_INT_GPIO7F		57
+#define AB8500_INT_GPIO8F		58
+#define AB8500_INT_GPIO9F		59
+#define AB8500_INT_GPIO10F		60
+#define AB8500_INT_GPIO11F		61
+#define AB8500_INT_GPIO12F		62
+#define AB8500_INT_GPIO13F		63
+#define AB8500_INT_GPIO24F		64
+#define AB8500_INT_GPIO25F		65
+#define AB8500_INT_GPIO36F		66
+#define AB8500_INT_GPIO37F		67
+#define AB8500_INT_GPIO38F		68
+#define AB8500_INT_GPIO39F		69
+#define AB8500_INT_GPIO40F		70
+#define AB8500_INT_GPIO41F		71
 #define AB8500_INT_ADP_SOURCE_ERROR	72
 #define AB8500_INT_ADP_SINK_ERROR	73
 #define AB8500_INT_ADP_PROBE_PLUG	74
@@ -141,6 +180,7 @@ struct ab8500 {
 
 struct regulator_reg_init;
 struct regulator_init_data;
+struct ab8500_gpio_platform_data;
 
 /**
  * struct ab8500_platform_data - AB8500 platform data
@@ -158,6 +198,7 @@ struct ab8500_platform_data {
 	struct ab8500_regulator_reg_init *regulator_reg_init;
 	int num_regulator;
 	struct regulator_init_data *regulator;
+	struct ab8500_gpio_platform_data *gpio;
 };
 
 extern int __devinit ab8500_init(struct ab8500 *ab8500);

include/linux/mfd/ab8500/gpio.h

+/*
+ * Copyright ST-Ericsson 2010.
+ *
+ * Author: Bibek Basu <bibek.basu@stericsson.com>
+ * Licensed under GPLv2.
+ */
+
+#ifndef _AB8500_GPIO_H
+#define _AB8500_GPIO_H
+
+/*
+ * Platform data to register a block: only the initial gpio/irq number.
+ */
+
+struct ab8500_gpio_platform_data {
+	int gpio_base;
+	u32 irq_base;
+	u8  config_reg[7];
+};
+
+#endif /* _AB8500_GPIO_H */