Commit be937f1f authored by Alexandr Smirnov's avatar Alexandr Smirnov Committed by Jeff Garzik

Marvell PHY m88e1111 driver fix

Marvell PHY m88e1111 (not sure about other models, but think they too)
works in two modes: fiber and copper. In Marvell PHY driver (that we
have in current community kernels) code supported only copper mode,
and this is not configurable, bits for copper mode are simply written
in registers during PHY initialization.

This patch adds support for both modes.
Signed-off-by: default avatarAlexandr Smirnov <asmirnov@ru.mvista.com>
Acked-by: default avatarAndy Fleming <afleming@freescale.com>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent d1847a72
......@@ -58,9 +58,25 @@
#define MII_M1111_RX_DELAY 0x80
#define MII_M1111_TX_DELAY 0x2
#define MII_M1111_PHY_EXT_SR 0x1b
#define MII_M1111_HWCFG_MODE_MASK 0xf
#define MII_M1111_HWCFG_MODE_RGMII 0xb
#define MII_M1111_HWCFG_MODE_MASK 0xf
#define MII_M1111_HWCFG_MODE_COPPER_RGMII 0xb
#define MII_M1111_HWCFG_MODE_FIBER_RGMII 0x3
#define MII_M1111_HWCFG_MODE_SGMII_NO_CLK 0x4
#define MII_M1111_HWCFG_FIBER_COPPER_AUTO 0x8000
#define MII_M1111_HWCFG_FIBER_COPPER_RES 0x2000
#define MII_M1111_COPPER 0
#define MII_M1111_FIBER 1
#define MII_M1011_PHY_STATUS 0x11
#define MII_M1011_PHY_STATUS_1000 0x8000
#define MII_M1011_PHY_STATUS_100 0x4000
#define MII_M1011_PHY_STATUS_SPD_MASK 0xc000
#define MII_M1011_PHY_STATUS_FULLDUPLEX 0x2000
#define MII_M1011_PHY_STATUS_RESOLVED 0x0800
#define MII_M1011_PHY_STATUS_LINK 0x0400
MODULE_DESCRIPTION("Marvell PHY driver");
MODULE_AUTHOR("Andy Fleming");
......@@ -141,12 +157,22 @@ static int marvell_config_aneg(struct phy_device *phydev)
static int m88e1111_config_init(struct phy_device *phydev)
{
int err;
int temp;
int mode;
/* Enable Fiber/Copper auto selection */
temp = phy_read(phydev, MII_M1111_PHY_EXT_SR);
temp |= MII_M1111_HWCFG_FIBER_COPPER_AUTO;
phy_write(phydev, MII_M1111_PHY_EXT_SR, temp);
temp = phy_read(phydev, MII_BMCR);
temp |= BMCR_RESET;
phy_write(phydev, MII_BMCR, temp);
if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
(phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) ||
(phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) ||
(phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) {
int temp;
temp = phy_read(phydev, MII_M1111_PHY_EXT_CR);
if (temp < 0)
......@@ -171,7 +197,13 @@ static int m88e1111_config_init(struct phy_device *phydev)
return temp;
temp &= ~(MII_M1111_HWCFG_MODE_MASK);
temp |= MII_M1111_HWCFG_MODE_RGMII;
mode = phy_read(phydev, MII_M1111_PHY_EXT_CR);
if (mode & MII_M1111_HWCFG_FIBER_COPPER_RES)
temp |= MII_M1111_HWCFG_MODE_FIBER_RGMII;
else
temp |= MII_M1111_HWCFG_MODE_COPPER_RGMII;
err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp);
if (err < 0)
......@@ -262,6 +294,93 @@ static int m88e1145_config_init(struct phy_device *phydev)
return 0;
}
/* marvell_read_status
*
* Generic status code does not detect Fiber correctly!
* Description:
* Check the link, then figure out the current state
* by comparing what we advertise with what the link partner
* advertises. Start by checking the gigabit possibilities,
* then move on to 10/100.
*/
static int marvell_read_status(struct phy_device *phydev)
{
int adv;
int err;
int lpa;
int status = 0;
/* Update the link, but return if there
* was an error */
err = genphy_update_link(phydev);
if (err)
return err;
if (AUTONEG_ENABLE == phydev->autoneg) {
status = phy_read(phydev, MII_M1011_PHY_STATUS);
if (status < 0)
return status;
lpa = phy_read(phydev, MII_LPA);
if (lpa < 0)
return lpa;
adv = phy_read(phydev, MII_ADVERTISE);
if (adv < 0)
return adv;
lpa &= adv;
if (status & MII_M1011_PHY_STATUS_FULLDUPLEX)
phydev->duplex = DUPLEX_FULL;
else
phydev->duplex = DUPLEX_HALF;
status = status & MII_M1011_PHY_STATUS_SPD_MASK;
phydev->pause = phydev->asym_pause = 0;
switch (status) {
case MII_M1011_PHY_STATUS_1000:
phydev->speed = SPEED_1000;
break;
case MII_M1011_PHY_STATUS_100:
phydev->speed = SPEED_100;
break;
default:
phydev->speed = SPEED_10;
break;
}
if (phydev->duplex == DUPLEX_FULL) {
phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0;
phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0;
}
} else {
int bmcr = phy_read(phydev, MII_BMCR);
if (bmcr < 0)
return bmcr;
if (bmcr & BMCR_FULLDPLX)
phydev->duplex = DUPLEX_FULL;
else
phydev->duplex = DUPLEX_HALF;
if (bmcr & BMCR_SPEED1000)
phydev->speed = SPEED_1000;
else if (bmcr & BMCR_SPEED100)
phydev->speed = SPEED_100;
else
phydev->speed = SPEED_10;
phydev->pause = phydev->asym_pause = 0;
}
return 0;
}
static struct phy_driver marvell_drivers[] = {
{
.phy_id = 0x01410c60,
......@@ -296,7 +415,7 @@ static struct phy_driver marvell_drivers[] = {
.flags = PHY_HAS_INTERRUPT,
.config_init = &m88e1111_config_init,
.config_aneg = &marvell_config_aneg,
.read_status = &genphy_read_status,
.read_status = &marvell_read_status,
.ack_interrupt = &marvell_ack_interrupt,
.config_intr = &marvell_config_intr,
.driver = { .owner = THIS_MODULE },
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment