ide: move CONFIG_IDE_ETRAX to drivers/ide/Kconfig

* Move ETRAX_IDE and friends from arch/cris/arch-{v10,v32}/drivers/Kconfig
  to drivers/ide/Kconfig.

* Don't force selecting ide-disk and ide-cd device drivers
  (please handle this through defconfig if necessary).

* Make ETRAX_IDE depend on BROKEN for the time being
  (it doesn't even compile currently).

Cc: Mikael Starvik <starvik@axis.com>
Acked-by: default avatarSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent acfad6e1
......@@ -542,45 +542,6 @@ config ETRAX_RS485_DISABLE_RECEIVER
loopback. Not all products are able to do this in software only.
Axis 2400/2401 must disable receiver.
config ETRAX_IDE
bool "ATA/IDE support"
select IDE
select BLK_DEV_IDE
select BLK_DEV_IDEDISK
select BLK_DEV_IDECD
select BLK_DEV_IDEDMA
select IDE_GENERIC
help
Enable this to get support for ATA/IDE.
You can't use parallel ports or SCSI ports
at the same time.
config ETRAX_IDE_DELAY
int "Delay for drives to regain consciousness"
depends on ETRAX_IDE
default 15
help
Number of seconds to wait for IDE drives to spin up after an IDE
reset.
choice
prompt "IDE reset pin"
depends on ETRAX_IDE
default ETRAX_IDE_PB7_RESET
config ETRAX_IDE_PB7_RESET
bool "Port_PB_Bit_7"
help
IDE reset on pin 7 on port B
config ETRAX_IDE_G27_RESET
bool "Port_G_Bit_27"
help
IDE reset on pin 27 on port G
endchoice
config ETRAX_USB_HOST
bool "USB host"
select USB
......
......@@ -582,18 +582,6 @@ config ETRAX_PE_CHANGEABLE_BITS
that a user can change the value on using ioctl's.
Bit set = changeable.
config ETRAX_IDE
bool "ATA/IDE support"
depends on ETRAX_ARCH_V32
select IDE
select BLK_DEV_IDE
select BLK_DEV_IDEDISK
select BLK_DEV_IDECD
select BLK_DEV_IDEDMA
select IDE_GENERIC
help
Enables the ETRAX IDE driver.
config ETRAX_CARDBUS
bool "Cardbus support"
depends on ETRAX_ARCH_V32
......
......@@ -882,6 +882,41 @@ config BLK_DEV_IDE_BAST
Say Y here if you want to support the onboard IDE channels on the
Simtec BAST or the Thorcom VR1000
config ETRAX_IDE
bool "ETRAX IDE support"
depends on CRIS && BROKEN
select BLK_DEV_IDEDMA
select IDE_GENERIC
help
Enables the ETRAX IDE driver.
You can't use parallel ports or SCSI ports at the same time.
config ETRAX_IDE_DELAY
int "Delay for drives to regain consciousness"
depends on ETRAX_IDE && ETRAX_ARCH_V10
default 15
help
Number of seconds to wait for IDE drives to spin up after an IDE
reset.
choice
prompt "IDE reset pin"
depends on ETRAX_IDE && ETRAX_ARCH_V10
default ETRAX_IDE_PB7_RESET
config ETRAX_IDE_PB7_RESET
bool "Port_PB_Bit_7"
help
IDE reset on pin 7 on port B
config ETRAX_IDE_G27_RESET
bool "Port_G_Bit_27"
help
IDE reset on pin 27 on port G
endchoice
config IDE_H8300
bool "H8300 IDE support"
depends on H8300
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment