Bluetooth: btusb: Use IS_ENABLED instead of #ifdef

For the different hardware support options, it is better to use
IS_ENABLED check. Let the compiler do the needed optimizations.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

drivers/bluetooth/btusb.c

@@ -2496,8 +2496,6 @@ static int btusb_shutdown_intel_new(struct hci_dev *hdev)
 	return 0;
 }
 
-#ifdef CONFIG_BT_HCIBTUSB_MTK
-
 #define FIRMWARE_MT7663		"mediatek/mt7663pr2h.bin"
 #define FIRMWARE_MT7668		"mediatek/mt7668pr2h.bin"
 
@@ -3058,7 +3056,6 @@ static int btusb_mtk_shutdown(struct hci_dev *hdev)
 
 MODULE_FIRMWARE(FIRMWARE_MT7663);
 MODULE_FIRMWARE(FIRMWARE_MT7668);
-#endif
 
 #ifdef CONFIG_PM
 /* Configure an out-of-band gpio as wake-up pin, if specified in device tree */
@@ -3418,7 +3415,6 @@ static int btusb_setup_qca(struct hci_dev *hdev)
 	return 0;
 }
 
-#ifdef CONFIG_BT_HCIBTUSB_BCM
 static inline int __set_diag_interface(struct hci_dev *hdev)
 {
 	struct btusb_data *data = hci_get_drvdata(hdev);
@@ -3505,7 +3501,6 @@ static int btusb_bcm_set_diag(struct hci_dev *hdev, bool enable)
 
 	return submit_or_queue_tx_urb(hdev, urb);
 }
-#endif
 
 #ifdef CONFIG_PM
 static irqreturn_t btusb_oob_wake_handler(int irq, void *priv)
@@ -3731,8 +3726,8 @@ static int btusb_probe(struct usb_interface *intf,
 	if (id->driver_info & BTUSB_BCM92035)
 		hdev->setup = btusb_setup_bcm92035;
 
-#ifdef CONFIG_BT_HCIBTUSB_BCM
-	if (id->driver_info & BTUSB_BCM_PATCHRAM) {
+	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) &&
+	    (id->driver_info & BTUSB_BCM_PATCHRAM)) {
 		hdev->manufacturer = 15;
 		hdev->setup = btbcm_setup_patchram;
 		hdev->set_diag = btusb_bcm_set_diag;
@@ -3742,7 +3737,8 @@ static int btusb_probe(struct usb_interface *intf,
 		data->diag = usb_ifnum_to_if(data->udev, ifnum_base + 2);
 	}
 
-	if (id->driver_info & BTUSB_BCM_APPLE) {
+	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) &&
+	    (id->driver_info & BTUSB_BCM_APPLE)) {
 		hdev->manufacturer = 15;
 		hdev->setup = btbcm_setup_apple;
 		hdev->set_diag = btusb_bcm_set_diag;
@@ -3750,7 +3746,6 @@ static int btusb_probe(struct usb_interface *intf,
 		/* Broadcom LM_DIAG Interface numbers are hardcoded */
 		data->diag = usb_ifnum_to_if(data->udev, ifnum_base + 2);
 	}
-#endif
 
 	if (id->driver_info & BTUSB_INTEL) {
 		hdev->manufacturer = 2;
@@ -3781,14 +3776,13 @@ static int btusb_probe(struct usb_interface *intf,
 	if (id->driver_info & BTUSB_MARVELL)
 		hdev->set_bdaddr = btusb_set_bdaddr_marvell;
 
-#ifdef CONFIG_BT_HCIBTUSB_MTK
-	if (id->driver_info & BTUSB_MEDIATEK) {
+	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_MTK) &&
+	    (id->driver_info & BTUSB_MEDIATEK)) {
 		hdev->setup = btusb_mtk_setup;
 		hdev->shutdown = btusb_mtk_shutdown;
 		hdev->manufacturer = 70;
 		set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
 	}
-#endif
 
 	if (id->driver_info & BTUSB_SWAVE) {
 		set_bit(HCI_QUIRK_FIXUP_INQUIRY_MODE, &hdev->quirks);
@@ -3893,15 +3887,13 @@ static int btusb_probe(struct usb_interface *intf,
 			goto out_free_dev;
 	}
 
-#ifdef CONFIG_BT_HCIBTUSB_BCM
-	if (data->diag) {
+	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) && data->diag) {
 		if (!usb_driver_claim_interface(&btusb_driver,
 						data->diag, data))
 			__set_diag_interface(hdev);
 		else
 			data->diag = NULL;
 	}
-#endif
 
 	if (enable_autosuspend)
 		usb_enable_autosuspend(data->udev);