Commit c220aec2 authored by Maxime Ripard's avatar Maxime Ripard

ARM: dts: sun6i: Add Merrii A31 Hummingbird support

This adds support for the A31 Hummingbird:
http://www.merrii.com/en/pla_d.asp?id=172

The Merrii A31 Hummingbird is a development board based on the
Allwinner A31 SoC with multiple USB ports through a USB hub chip,
a uSD slot, a 10/100/1000M ethernet port, an AP6210 WiFi/BT chip,
TV-in, HDMI, VGA, audio in/out ports, and LCD/CSI headers.
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: enable usbphy, ehci0, ohci0 for on-board usb hub;
 add pcf8563 rtc node; add comments for i2c0 and mmc0 pull-ups;
 correct ethernet phy address to 0x01; drop uart2 (BT chip has
 no power) and uart3 (no device); use proper commit message]
Signed-off-by: default avatarChen-Yu Tsai <wens@csie.org>
parent e5073fde
......@@ -375,6 +375,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31-app4-evb1.dtb \
sun6i-a31-colombus.dtb \
sun6i-a31-hummingbird.dtb \
sun6i-a31-m9.dtb
dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-cubieboard2.dtb \
......
/*
* Copyright 2014 Maxime Ripard
*
* Maxime Ripard <maxime.ripard@free-electrons.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
/include/ "sun6i-a31.dtsi"
/include/ "sunxi-common-regulators.dtsi"
/ {
model = "Merrii A31 Hummingbird";
compatible = "merrii,a31-hummingbird", "allwinner,sun6i-a31";
chosen {
bootargs = "earlyprintk console=ttyS0,115200";
};
soc@01c00000 {
mmc0: mmc@01c0f000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_hummingbird>;
vmmc-supply = <&reg_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 0 8 0>; /* PA8 */
cd-inverted;
status = "okay";
};
usbphy: phy@01c19400 {
usb1_vbus-supply = <&reg_usb1_vbus>;
status = "okay";
};
ehci0: usb@01c1a000 {
status = "okay";
};
ohci0: usb@01c1a400 {
status = "okay";
};
pio: pinctrl@01c20800 {
mmc0_pins_a: mmc0@0 {
/* external pull-ups missing for some pins */
allwinner,pull = <1>;
};
mmc0_cd_pin_hummingbird: mmc0_cd_pin@0 {
allwinner,pins = "PA8";
allwinner,function = "gpio_in";
allwinner,drive = <0>;
allwinner,pull = <1>;
};
usb1_vbus_pin_a: usb1_vbus_pin@0 {
allwinner,pins = "PH24";
allwinner,function = "gpio_out";
allwinner,drive = <0>;
allwinner,pull = <0>;
};
};
uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
i2c0: i2c@01c2ac00 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
/* pull-ups and devices require AXP221 DLDO3 */
status = "failed";
};
i2c1: i2c@01c2b000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
i2c2: i2c@01c2b400 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
pcf8563: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
};
gmac: ethernet@01c30000 {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
};
reg_usb1_vbus: usb1-vbus {
pinctrl-0 = <&usb1_vbus_pin_a>;
gpio = <&pio 7 24 0>; /* PH24 */
status = "okay";
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment