ARM: dts: sun7i: Enable mmc controller on various A20 boards

The cd pin settings have been taken from the original firmware fex files,
and have been confirmed to work on the actual boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arch/arm/boot/dts/sun7i-a20-cubieboard2.dts

@@ -20,6 +20,15 @@ / {
 	compatible = "cubietech,cubieboard2", "allwinner,sun7i-a20";
 
 	soc@01c00000 {
+		mmc0: mmc@01c0f000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+			bus-width = <4>;
+			cd-gpios = <&pio 7 1 0>; /* PH1 */
+			cd-inverted;
+			status = "okay";
+		};
+
 		usbphy: phy@01c13400 {
 			usb1_vbus-supply = <&reg_usb1_vbus>;
 			usb2_vbus-supply = <&reg_usb2_vbus>;

arch/arm/boot/dts/sun7i-a20-cubietruck.dts

@@ -20,6 +20,15 @@ / {
 	compatible = "cubietech,cubietruck", "allwinner,sun7i-a20";
 
 	soc@01c00000 {
+		mmc0: mmc@01c0f000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+			bus-width = <4>;
+			cd-gpios = <&pio 7 1 0>; /* PH1 */
+			cd-inverted;
+			status = "okay";
+		};
+
 		usbphy: phy@01c13400 {
 			usb1_vbus-supply = <&reg_usb1_vbus>;
 			usb2_vbus-supply = <&reg_usb2_vbus>;

arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts

@@ -31,6 +31,24 @@ spi1: spi@01c06000 {
 			status = "okay";
 		};
 
+		mmc0: mmc@01c0f000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+			bus-width = <4>;
+			cd-gpios = <&pio 7 1 0>; /* PH1 */
+			cd-inverted;
+			status = "okay";
+		};
+
+		mmc3: mmc@01c12000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olinuxinom>;
+			bus-width = <4>;
+			cd-gpios = <&pio 7 11 0>; /* PH11 */
+			cd-inverted;
+			status = "okay";
+		};
+
 		usbphy: phy@01c13400 {
 			usb1_vbus-supply = <&reg_usb1_vbus>;
 			usb2_vbus-supply = <&reg_usb2_vbus>;
@@ -65,6 +83,13 @@ ohci1: usb@01c1c400 {
 		};
 
 		pinctrl@01c20800 {
+			mmc3_cd_pin_olinuxinom: mmc3_cd_pin@0 {
+				allwinner,pins = "PH11";
+				allwinner,function = "gpio_in";
+				allwinner,drive = <0>;
+				allwinner,pull = <1>;
+			};
+
 			led_pins_olinuxino: led_pins@0 {
 				allwinner,pins = "PH2";
 				allwinner,function = "gpio_out";