OMAP: DSS2: move memory_read()

Move memory_read() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>

arch/arm/plat-omap/include/plat/display.h

@@ -495,10 +495,6 @@ struct omap_dss_device {
 	bool (*get_mirror)(struct omap_dss_device *dssdev);
 	int (*set_mirror)(struct omap_dss_device *dssdev, bool enable);
 
-	int (*memory_read)(struct omap_dss_device *dssdev,
-			void *buf, size_t size,
-			u16 x, u16 y, u16 w, u16 h);
-
 	int (*set_wss)(struct omap_dss_device *dssdev, u32 wss);
 	u32 (*get_wss)(struct omap_dss_device *dssdev);
 

drivers/video/omap2/displays/panel-taal.c

@@ -847,6 +847,10 @@ static int taal_memory_read(struct omap_dss_device *dssdev,
 	int first = 1;
 	int plen;
 	unsigned buf_used = 0;
+	struct taal_data *td = dev_get_drvdata(&dssdev->dev);
+
+	if (!td->enabled)
+		return -ENODEV;
 
 	if (size < w * h * 3)
 		return -ENOMEM;
@@ -855,6 +859,8 @@ static int taal_memory_read(struct omap_dss_device *dssdev,
 			dssdev->panel.timings.x_res *
 			dssdev->panel.timings.y_res * 3);
 
+	dsi_bus_lock();
+
 	/* plen 1 or 2 goes into short packet. until checksum error is fixed,
 	 * use short packets. plen 32 works, but bigger packets seem to cause
 	 * an error. */
@@ -863,11 +869,11 @@ static int taal_memory_read(struct omap_dss_device *dssdev,
 	else
 		plen = 2;
 
-	taal_setup_update(dssdev, x, y, w, h);
+	taal_set_update_window(x, y, w, h);
 
 	r = dsi_vc_set_max_rx_packet_size(TCH, plen);
 	if (r)
-		return r;
+		goto err0;
 
 	while (buf_used < size) {
 		u8 dcs_cmd = first ? 0x2e : 0x3e;
@@ -900,7 +906,8 @@ static int taal_memory_read(struct omap_dss_device *dssdev,
 
 err:
 	dsi_vc_set_max_rx_packet_size(TCH, 1);
-
+err0:
+	dsi_bus_unlock();
 	return r;
 }
 

drivers/video/omap2/dss/dsi.c

@@ -3584,34 +3584,6 @@ static bool dsi_display_get_mirror(struct omap_dss_device *dssdev)
 	return dssdev->driver->get_mirror(dssdev);
 }
 
-static int dsi_display_memory_read(struct omap_dss_device *dssdev,
-		void *buf, size_t size,
-		u16 x, u16 y, u16 w, u16 h)
-{
-	int r;
-
-	DSSDBGF("");
-
-	if (!dssdev->driver->memory_read)
-		return -EINVAL;
-
-	if (dssdev->state != OMAP_DSS_DISPLAY_ACTIVE)
-		return -EIO;
-
-	dsi_bus_lock();
-
-	r = dssdev->driver->memory_read(dssdev, buf, size,
-			x, y, w, h);
-
-	/* Memory read usually changes the update area. This will
-	 * force the next update to re-set the update area */
-	dsi.active_update_region.dirty = true;
-
-	dsi_bus_unlock();
-
-	return r;
-}
-
 void dsi_get_overlay_fifo_thresholds(enum omap_plane plane,
 		u32 fifo_size, enum omap_burst_size *burst_size,
 		u32 *fifo_low, u32 *fifo_high)
@@ -3646,8 +3618,6 @@ int dsi_init_display(struct omap_dss_device *dssdev)
 	dssdev->get_mirror = dsi_display_get_mirror;
 	dssdev->set_mirror = dsi_display_set_mirror;
 
-	dssdev->memory_read = dsi_display_memory_read;
-
 	/* XXX these should be figured out dynamically */
 	dssdev->caps = OMAP_DSS_DISPLAY_CAP_MANUAL_UPDATE |
 		OMAP_DSS_DISPLAY_CAP_TEAR_ELIM;

drivers/video/omap2/omapfb/omapfb-ioctl.c

@@ -374,7 +374,7 @@ static int omapfb_memory_read(struct fb_info *fbi,
 	void *buf;
 	int r;
 
-	if (!display || !display->memory_read)
+	if (!display || !display->driver->memory_read)
 		return -ENOENT;
 
 	if (!access_ok(VERIFY_WRITE, mr->buffer, mr->buffer_size))
@@ -389,7 +389,7 @@ static int omapfb_memory_read(struct fb_info *fbi,
 		return -ENOMEM;
 	}
 
-	r = display->memory_read(display, buf, mr->buffer_size,
+	r = display->driver->memory_read(display, buf, mr->buffer_size,
 			mr->x, mr->y, mr->w, mr->h);
 
 	if (r > 0) {